1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * arch/arm/mach-at91/pm_slow_clock.S 4 * 5 * Copyright (C) 2006 Savin Zlobec 6 * 7 * AT91SAM9 support: 8 * Copyright (C) 2007 Anti Sullin <anti.sullin@artecdesign.ee> 9 */ 10 #include <linux/linkage.h> 11 #include <linux/clk/at91_pmc.h> 12 #include "pm.h" 13 #include "pm_data-offsets.h" 14 15 #define SRAMC_SELF_FRESH_ACTIVE 0x01 16 #define SRAMC_SELF_FRESH_EXIT 0x00 17 18 pmc .req r0 19 tmp1 .req r4 20 tmp2 .req r5 21 tmp3 .req r6 22 23 /* 24 * Wait until master clock is ready (after switching master clock source) 25 */ 26 .macro wait_mckrdy 27 1: ldr tmp1, [pmc, #AT91_PMC_SR] 28 tst tmp1, #AT91_PMC_MCKRDY 29 beq 1b 30 .endm 31 32 /* 33 * Wait until master oscillator has stabilized. 34 */ 35 .macro wait_moscrdy 36 1: ldr tmp1, [pmc, #AT91_PMC_SR] 37 tst tmp1, #AT91_PMC_MOSCS 38 beq 1b 39 .endm 40 41 /* 42 * Wait for main oscillator selection is done 43 */ 44 .macro wait_moscsels 45 1: ldr tmp1, [pmc, #AT91_PMC_SR] 46 tst tmp1, #AT91_PMC_MOSCSELS 47 beq 1b 48 .endm 49 50 /* 51 * Put the processor to enter the idle state 52 */ 53 .macro at91_cpu_idle 54 55 #if defined(CONFIG_CPU_V7) 56 mov tmp1, #AT91_PMC_PCK 57 str tmp1, [pmc, #AT91_PMC_SCDR] 58 59 dsb 60 61 wfi @ Wait For Interrupt 62 #else 63 mcr p15, 0, tmp1, c7, c0, 4 64 #endif 65 66 .endm 67 68 .text 69 70 .arm 71 72 /* 73 * void at91_suspend_sram_fn(struct at91_pm_data*) 74 * @input param: 75 * @r0: base address of struct at91_pm_data 76 */ 77 /* at91_pm_suspend_in_sram must be 8-byte aligned per the requirements of fncpy() */ 78 .align 3 79 ENTRY(at91_pm_suspend_in_sram) 80 /* Save registers on stack */ 81 stmfd sp!, {r4 - r12, lr} 82 83 /* Drain write buffer */ 84 mov tmp1, #0 85 mcr p15, 0, tmp1, c7, c10, 4 86 87 ldr tmp1, [r0, #PM_DATA_PMC] 88 str tmp1, .pmc_base 89 ldr tmp1, [r0, #PM_DATA_RAMC0] 90 str tmp1, .sramc_base 91 ldr tmp1, [r0, #PM_DATA_RAMC1] 92 str tmp1, .sramc1_base 93 ldr tmp1, [r0, #PM_DATA_MEMCTRL] 94 str tmp1, .memtype 95 ldr tmp1, [r0, #PM_DATA_MODE] 96 str tmp1, .pm_mode 97 ldr tmp1, [r0, #PM_DATA_PMC_MCKR_OFFSET] 98 str tmp1, .mckr_offset 99 ldr tmp1, [r0, #PM_DATA_PMC_VERSION] 100 str tmp1, .pmc_version 101 /* Both ldrne below are here to preload their address in the TLB */ 102 ldr tmp1, [r0, #PM_DATA_SHDWC] 103 str tmp1, .shdwc 104 cmp tmp1, #0 105 ldrne tmp2, [tmp1, #0] 106 ldr tmp1, [r0, #PM_DATA_SFRBU] 107 str tmp1, .sfrbu 108 cmp tmp1, #0 109 ldrne tmp2, [tmp1, #0x10] 110 111 /* Active the self-refresh mode */ 112 mov r0, #SRAMC_SELF_FRESH_ACTIVE 113 bl at91_sramc_self_refresh 114 115 ldr r0, .pm_mode 116 cmp r0, #AT91_PM_STANDBY 117 beq standby 118 cmp r0, #AT91_PM_BACKUP 119 beq backup_mode 120 121 bl at91_ulp_mode 122 b exit_suspend 123 124 standby: 125 /* Wait for interrupt */ 126 ldr pmc, .pmc_base 127 at91_cpu_idle 128 b exit_suspend 129 130 backup_mode: 131 bl at91_backup_mode 132 b exit_suspend 133 134 exit_suspend: 135 /* Exit the self-refresh mode */ 136 mov r0, #SRAMC_SELF_FRESH_EXIT 137 bl at91_sramc_self_refresh 138 139 /* Restore registers, and return */ 140 ldmfd sp!, {r4 - r12, pc} 141 ENDPROC(at91_pm_suspend_in_sram) 142 143 ENTRY(at91_backup_mode) 144 /* Switch the master clock source to slow clock. */ 145 ldr pmc, .pmc_base 146 ldr tmp2, .mckr_offset 147 ldr tmp1, [pmc, tmp2] 148 bic tmp1, tmp1, #AT91_PMC_CSS 149 str tmp1, [pmc, tmp2] 150 151 wait_mckrdy 152 153 /*BUMEN*/ 154 ldr r0, .sfrbu 155 mov tmp1, #0x1 156 str tmp1, [r0, #0x10] 157 158 /* Shutdown */ 159 ldr r0, .shdwc 160 mov tmp1, #0xA5000000 161 add tmp1, tmp1, #0x1 162 str tmp1, [r0, #0] 163 ENDPROC(at91_backup_mode) 164 165 .macro at91_pm_ulp0_mode 166 ldr pmc, .pmc_base 167 ldr tmp2, .pm_mode 168 ldr tmp3, .mckr_offset 169 170 /* Check if ULP0 fast variant has been requested. */ 171 cmp tmp2, #AT91_PM_ULP0_FAST 172 bne 0f 173 174 /* Set highest prescaler for power saving */ 175 ldr tmp1, [pmc, tmp3] 176 bic tmp1, tmp1, #AT91_PMC_PRES 177 orr tmp1, tmp1, #AT91_PMC_PRES_64 178 str tmp1, [pmc, tmp3] 179 wait_mckrdy 180 b 1f 181 182 0: 183 /* Turn off the crystal oscillator */ 184 ldr tmp1, [pmc, #AT91_CKGR_MOR] 185 bic tmp1, tmp1, #AT91_PMC_MOSCEN 186 orr tmp1, tmp1, #AT91_PMC_KEY 187 str tmp1, [pmc, #AT91_CKGR_MOR] 188 189 /* Save RC oscillator state */ 190 ldr tmp1, [pmc, #AT91_PMC_SR] 191 str tmp1, .saved_osc_status 192 tst tmp1, #AT91_PMC_MOSCRCS 193 bne 1f 194 195 /* Turn off RC oscillator */ 196 ldr tmp1, [pmc, #AT91_CKGR_MOR] 197 bic tmp1, tmp1, #AT91_PMC_MOSCRCEN 198 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 199 orr tmp1, tmp1, #AT91_PMC_KEY 200 str tmp1, [pmc, #AT91_CKGR_MOR] 201 202 /* Wait main RC disabled done */ 203 2: ldr tmp1, [pmc, #AT91_PMC_SR] 204 tst tmp1, #AT91_PMC_MOSCRCS 205 bne 2b 206 207 /* Wait for interrupt */ 208 1: at91_cpu_idle 209 210 /* Check if ULP0 fast variant has been requested. */ 211 cmp tmp2, #AT91_PM_ULP0_FAST 212 bne 5f 213 214 /* Set lowest prescaler for fast resume. */ 215 ldr tmp1, [pmc, tmp3] 216 bic tmp1, tmp1, #AT91_PMC_PRES 217 str tmp1, [pmc, tmp3] 218 wait_mckrdy 219 b 6f 220 221 5: /* Restore RC oscillator state */ 222 ldr tmp1, .saved_osc_status 223 tst tmp1, #AT91_PMC_MOSCRCS 224 beq 4f 225 226 /* Turn on RC oscillator */ 227 ldr tmp1, [pmc, #AT91_CKGR_MOR] 228 orr tmp1, tmp1, #AT91_PMC_MOSCRCEN 229 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 230 orr tmp1, tmp1, #AT91_PMC_KEY 231 str tmp1, [pmc, #AT91_CKGR_MOR] 232 233 /* Wait main RC stabilization */ 234 3: ldr tmp1, [pmc, #AT91_PMC_SR] 235 tst tmp1, #AT91_PMC_MOSCRCS 236 beq 3b 237 238 /* Turn on the crystal oscillator */ 239 4: ldr tmp1, [pmc, #AT91_CKGR_MOR] 240 orr tmp1, tmp1, #AT91_PMC_MOSCEN 241 orr tmp1, tmp1, #AT91_PMC_KEY 242 str tmp1, [pmc, #AT91_CKGR_MOR] 243 244 wait_moscrdy 245 6: 246 .endm 247 248 /** 249 * Note: This procedure only applies on the platform which uses 250 * the external crystal oscillator as a main clock source. 251 */ 252 .macro at91_pm_ulp1_mode 253 ldr pmc, .pmc_base 254 ldr tmp2, .mckr_offset 255 256 /* Save RC oscillator state and check if it is enabled. */ 257 ldr tmp1, [pmc, #AT91_PMC_SR] 258 str tmp1, .saved_osc_status 259 tst tmp1, #AT91_PMC_MOSCRCS 260 bne 2f 261 262 /* Enable RC oscillator */ 263 ldr tmp1, [pmc, #AT91_CKGR_MOR] 264 orr tmp1, tmp1, #AT91_PMC_MOSCRCEN 265 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 266 orr tmp1, tmp1, #AT91_PMC_KEY 267 str tmp1, [pmc, #AT91_CKGR_MOR] 268 269 /* Wait main RC stabilization */ 270 1: ldr tmp1, [pmc, #AT91_PMC_SR] 271 tst tmp1, #AT91_PMC_MOSCRCS 272 beq 1b 273 274 /* Switch the main clock source to 12-MHz RC oscillator */ 275 2: ldr tmp1, [pmc, #AT91_CKGR_MOR] 276 bic tmp1, tmp1, #AT91_PMC_MOSCSEL 277 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 278 orr tmp1, tmp1, #AT91_PMC_KEY 279 str tmp1, [pmc, #AT91_CKGR_MOR] 280 281 wait_moscsels 282 283 /* Disable the crystal oscillator */ 284 ldr tmp1, [pmc, #AT91_CKGR_MOR] 285 bic tmp1, tmp1, #AT91_PMC_MOSCEN 286 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 287 orr tmp1, tmp1, #AT91_PMC_KEY 288 str tmp1, [pmc, #AT91_CKGR_MOR] 289 290 /* Switch the master clock source to main clock */ 291 ldr tmp1, [pmc, tmp2] 292 bic tmp1, tmp1, #AT91_PMC_CSS 293 orr tmp1, tmp1, #AT91_PMC_CSS_MAIN 294 str tmp1, [pmc, tmp2] 295 296 wait_mckrdy 297 298 /* Enter the ULP1 mode by set WAITMODE bit in CKGR_MOR */ 299 ldr tmp1, [pmc, #AT91_CKGR_MOR] 300 orr tmp1, tmp1, #AT91_PMC_WAITMODE 301 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 302 orr tmp1, tmp1, #AT91_PMC_KEY 303 str tmp1, [pmc, #AT91_CKGR_MOR] 304 305 /* Quirk for SAM9X60's PMC */ 306 nop 307 nop 308 309 wait_mckrdy 310 311 /* Enable the crystal oscillator */ 312 ldr tmp1, [pmc, #AT91_CKGR_MOR] 313 orr tmp1, tmp1, #AT91_PMC_MOSCEN 314 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 315 orr tmp1, tmp1, #AT91_PMC_KEY 316 str tmp1, [pmc, #AT91_CKGR_MOR] 317 318 wait_moscrdy 319 320 /* Switch the master clock source to slow clock */ 321 ldr tmp1, [pmc, tmp2] 322 bic tmp1, tmp1, #AT91_PMC_CSS 323 str tmp1, [pmc, tmp2] 324 325 wait_mckrdy 326 327 /* Switch main clock source to crystal oscillator */ 328 ldr tmp1, [pmc, #AT91_CKGR_MOR] 329 orr tmp1, tmp1, #AT91_PMC_MOSCSEL 330 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 331 orr tmp1, tmp1, #AT91_PMC_KEY 332 str tmp1, [pmc, #AT91_CKGR_MOR] 333 334 wait_moscsels 335 336 /* Switch the master clock source to main clock */ 337 ldr tmp1, [pmc, tmp2] 338 bic tmp1, tmp1, #AT91_PMC_CSS 339 orr tmp1, tmp1, #AT91_PMC_CSS_MAIN 340 str tmp1, [pmc, tmp2] 341 342 wait_mckrdy 343 344 /* Restore RC oscillator state */ 345 ldr tmp1, .saved_osc_status 346 tst tmp1, #AT91_PMC_MOSCRCS 347 bne 3f 348 349 /* Disable RC oscillator */ 350 ldr tmp1, [pmc, #AT91_CKGR_MOR] 351 bic tmp1, tmp1, #AT91_PMC_MOSCRCEN 352 bic tmp1, tmp1, #AT91_PMC_KEY_MASK 353 orr tmp1, tmp1, #AT91_PMC_KEY 354 str tmp1, [pmc, #AT91_CKGR_MOR] 355 356 /* Wait RC oscillator disable done */ 357 4: ldr tmp1, [pmc, #AT91_PMC_SR] 358 tst tmp1, #AT91_PMC_MOSCRCS 359 bne 4b 360 361 3: 362 .endm 363 364 .macro at91_plla_disable 365 /* Save PLLA setting and disable it */ 366 ldr tmp1, .pmc_version 367 cmp tmp1, #AT91_PMC_V1 368 beq 1f 369 370 #ifdef CONFIG_SOC_SAM9X60 371 /* Save PLLA settings. */ 372 ldr tmp2, [pmc, #AT91_PMC_PLL_UPDT] 373 bic tmp2, tmp2, #AT91_PMC_PLL_UPDT_ID 374 str tmp2, [pmc, #AT91_PMC_PLL_UPDT] 375 376 /* save div. */ 377 mov tmp1, #0 378 ldr tmp2, [pmc, #AT91_PMC_PLL_CTRL0] 379 bic tmp2, tmp2, #0xffffff00 380 orr tmp1, tmp1, tmp2 381 382 /* save mul. */ 383 ldr tmp2, [pmc, #AT91_PMC_PLL_CTRL1] 384 bic tmp2, tmp2, #0xffffff 385 orr tmp1, tmp1, tmp2 386 str tmp1, .saved_pllar 387 388 /* step 2. */ 389 ldr tmp1, [pmc, #AT91_PMC_PLL_UPDT] 390 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_UPDATE 391 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_ID 392 str tmp1, [pmc, #AT91_PMC_PLL_UPDT] 393 394 /* step 3. */ 395 ldr tmp1, [pmc, #AT91_PMC_PLL_CTRL0] 396 bic tmp1, tmp1, #AT91_PMC_PLL_CTRL0_ENPLLCK 397 orr tmp1, tmp1, #AT91_PMC_PLL_CTRL0_ENPLL 398 str tmp1, [pmc, #AT91_PMC_PLL_CTRL0] 399 400 /* step 4. */ 401 ldr tmp1, [pmc, #AT91_PMC_PLL_UPDT] 402 orr tmp1, tmp1, #AT91_PMC_PLL_UPDT_UPDATE 403 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_ID 404 str tmp1, [pmc, #AT91_PMC_PLL_UPDT] 405 406 /* step 5. */ 407 ldr tmp1, [pmc, #AT91_PMC_PLL_CTRL0] 408 bic tmp1, tmp1, #AT91_PMC_PLL_CTRL0_ENPLL 409 str tmp1, [pmc, #AT91_PMC_PLL_CTRL0] 410 411 /* step 7. */ 412 ldr tmp1, [pmc, #AT91_PMC_PLL_UPDT] 413 orr tmp1, tmp1, #AT91_PMC_PLL_UPDT_UPDATE 414 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_ID 415 str tmp1, [pmc, #AT91_PMC_PLL_UPDT] 416 417 b 2f 418 #endif 419 420 1: /* Save PLLA setting and disable it */ 421 ldr tmp1, [pmc, #AT91_CKGR_PLLAR] 422 str tmp1, .saved_pllar 423 424 /* Disable PLLA. */ 425 mov tmp1, #AT91_PMC_PLLCOUNT 426 orr tmp1, tmp1, #(1 << 29) /* bit 29 always set */ 427 str tmp1, [pmc, #AT91_CKGR_PLLAR] 428 2: 429 .endm 430 431 .macro at91_plla_enable 432 ldr tmp2, .saved_pllar 433 ldr tmp3, .pmc_version 434 cmp tmp3, #AT91_PMC_V1 435 beq 4f 436 437 #ifdef CONFIG_SOC_SAM9X60 438 /* step 1. */ 439 ldr tmp1, [pmc, #AT91_PMC_PLL_UPDT] 440 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_ID 441 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_UPDATE 442 str tmp1, [pmc, #AT91_PMC_PLL_UPDT] 443 444 /* step 2. */ 445 ldr tmp1, =AT91_PMC_PLL_ACR_DEFAULT_PLLA 446 str tmp1, [pmc, #AT91_PMC_PLL_ACR] 447 448 /* step 3. */ 449 ldr tmp1, [pmc, #AT91_PMC_PLL_CTRL1] 450 mov tmp3, tmp2 451 bic tmp3, tmp3, #0xffffff 452 orr tmp1, tmp1, tmp3 453 str tmp1, [pmc, #AT91_PMC_PLL_CTRL1] 454 455 /* step 8. */ 456 ldr tmp1, [pmc, #AT91_PMC_PLL_UPDT] 457 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_ID 458 orr tmp1, tmp1, #AT91_PMC_PLL_UPDT_UPDATE 459 str tmp1, [pmc, #AT91_PMC_PLL_UPDT] 460 461 /* step 9. */ 462 ldr tmp1, [pmc, #AT91_PMC_PLL_CTRL0] 463 orr tmp1, tmp1, #AT91_PMC_PLL_CTRL0_ENLOCK 464 orr tmp1, tmp1, #AT91_PMC_PLL_CTRL0_ENPLL 465 orr tmp1, tmp1, #AT91_PMC_PLL_CTRL0_ENPLLCK 466 bic tmp1, tmp1, #0xff 467 mov tmp3, tmp2 468 bic tmp3, tmp3, #0xffffff00 469 orr tmp1, tmp1, tmp3 470 str tmp1, [pmc, #AT91_PMC_PLL_CTRL0] 471 472 /* step 10. */ 473 ldr tmp1, [pmc, #AT91_PMC_PLL_UPDT] 474 orr tmp1, tmp1, #AT91_PMC_PLL_UPDT_UPDATE 475 bic tmp1, tmp1, #AT91_PMC_PLL_UPDT_ID 476 str tmp1, [pmc, #AT91_PMC_PLL_UPDT] 477 478 /* step 11. */ 479 3: ldr tmp1, [pmc, #AT91_PMC_PLL_ISR0] 480 tst tmp1, #0x1 481 beq 3b 482 b 2f 483 #endif 484 485 /* Restore PLLA setting */ 486 4: str tmp2, [pmc, #AT91_CKGR_PLLAR] 487 488 /* Enable PLLA. */ 489 tst tmp2, #(AT91_PMC_MUL & 0xff0000) 490 bne 1f 491 tst tmp2, #(AT91_PMC_MUL & ~0xff0000) 492 beq 2f 493 494 1: ldr tmp1, [pmc, #AT91_PMC_SR] 495 tst tmp1, #AT91_PMC_LOCKA 496 beq 1b 497 2: 498 .endm 499 500 ENTRY(at91_ulp_mode) 501 ldr pmc, .pmc_base 502 ldr tmp2, .mckr_offset 503 ldr tmp3, .pm_mode 504 505 /* Save Master clock setting */ 506 ldr tmp1, [pmc, tmp2] 507 str tmp1, .saved_mckr 508 509 /* 510 * Set master clock source to: 511 * - MAINCK if using ULP0 fast variant 512 * - slow clock, otherwise 513 */ 514 bic tmp1, tmp1, #AT91_PMC_CSS 515 cmp tmp3, #AT91_PM_ULP0_FAST 516 bne save_mck 517 orr tmp1, tmp1, #AT91_PMC_CSS_MAIN 518 save_mck: 519 str tmp1, [pmc, tmp2] 520 521 wait_mckrdy 522 523 at91_plla_disable 524 525 cmp tmp3, #AT91_PM_ULP1 526 beq ulp1_mode 527 528 at91_pm_ulp0_mode 529 b ulp_exit 530 531 ulp1_mode: 532 at91_pm_ulp1_mode 533 b ulp_exit 534 535 ulp_exit: 536 ldr pmc, .pmc_base 537 538 at91_plla_enable 539 540 /* 541 * Restore master clock setting 542 */ 543 ldr tmp1, .mckr_offset 544 ldr tmp2, .saved_mckr 545 str tmp2, [pmc, tmp1] 546 547 wait_mckrdy 548 549 mov pc, lr 550 ENDPROC(at91_ulp_mode) 551 552 /* 553 * void at91_sramc_self_refresh(unsigned int is_active) 554 * 555 * @input param: 556 * @r0: 1 - active self-refresh mode 557 * 0 - exit self-refresh mode 558 * register usage: 559 * @r1: memory type 560 * @r2: base address of the sram controller 561 */ 562 563 ENTRY(at91_sramc_self_refresh) 564 ldr r1, .memtype 565 ldr r2, .sramc_base 566 567 cmp r1, #AT91_MEMCTRL_MC 568 bne ddrc_sf 569 570 /* 571 * at91rm9200 Memory controller 572 */ 573 574 /* 575 * For exiting the self-refresh mode, do nothing, 576 * automatically exit the self-refresh mode. 577 */ 578 tst r0, #SRAMC_SELF_FRESH_ACTIVE 579 beq exit_sramc_sf 580 581 /* Active SDRAM self-refresh mode */ 582 mov r3, #1 583 str r3, [r2, #AT91_MC_SDRAMC_SRR] 584 b exit_sramc_sf 585 586 ddrc_sf: 587 cmp r1, #AT91_MEMCTRL_DDRSDR 588 bne sdramc_sf 589 590 /* 591 * DDR Memory controller 592 */ 593 tst r0, #SRAMC_SELF_FRESH_ACTIVE 594 beq ddrc_exit_sf 595 596 /* LPDDR1 --> force DDR2 mode during self-refresh */ 597 ldr r3, [r2, #AT91_DDRSDRC_MDR] 598 str r3, .saved_sam9_mdr 599 bic r3, r3, #~AT91_DDRSDRC_MD 600 cmp r3, #AT91_DDRSDRC_MD_LOW_POWER_DDR 601 ldreq r3, [r2, #AT91_DDRSDRC_MDR] 602 biceq r3, r3, #AT91_DDRSDRC_MD 603 orreq r3, r3, #AT91_DDRSDRC_MD_DDR2 604 streq r3, [r2, #AT91_DDRSDRC_MDR] 605 606 /* Active DDRC self-refresh mode */ 607 ldr r3, [r2, #AT91_DDRSDRC_LPR] 608 str r3, .saved_sam9_lpr 609 bic r3, r3, #AT91_DDRSDRC_LPCB 610 orr r3, r3, #AT91_DDRSDRC_LPCB_SELF_REFRESH 611 str r3, [r2, #AT91_DDRSDRC_LPR] 612 613 /* If using the 2nd ddr controller */ 614 ldr r2, .sramc1_base 615 cmp r2, #0 616 beq no_2nd_ddrc 617 618 ldr r3, [r2, #AT91_DDRSDRC_MDR] 619 str r3, .saved_sam9_mdr1 620 bic r3, r3, #~AT91_DDRSDRC_MD 621 cmp r3, #AT91_DDRSDRC_MD_LOW_POWER_DDR 622 ldreq r3, [r2, #AT91_DDRSDRC_MDR] 623 biceq r3, r3, #AT91_DDRSDRC_MD 624 orreq r3, r3, #AT91_DDRSDRC_MD_DDR2 625 streq r3, [r2, #AT91_DDRSDRC_MDR] 626 627 /* Active DDRC self-refresh mode */ 628 ldr r3, [r2, #AT91_DDRSDRC_LPR] 629 str r3, .saved_sam9_lpr1 630 bic r3, r3, #AT91_DDRSDRC_LPCB 631 orr r3, r3, #AT91_DDRSDRC_LPCB_SELF_REFRESH 632 str r3, [r2, #AT91_DDRSDRC_LPR] 633 634 no_2nd_ddrc: 635 b exit_sramc_sf 636 637 ddrc_exit_sf: 638 /* Restore MDR in case of LPDDR1 */ 639 ldr r3, .saved_sam9_mdr 640 str r3, [r2, #AT91_DDRSDRC_MDR] 641 /* Restore LPR on AT91 with DDRAM */ 642 ldr r3, .saved_sam9_lpr 643 str r3, [r2, #AT91_DDRSDRC_LPR] 644 645 /* If using the 2nd ddr controller */ 646 ldr r2, .sramc1_base 647 cmp r2, #0 648 ldrne r3, .saved_sam9_mdr1 649 strne r3, [r2, #AT91_DDRSDRC_MDR] 650 ldrne r3, .saved_sam9_lpr1 651 strne r3, [r2, #AT91_DDRSDRC_LPR] 652 653 b exit_sramc_sf 654 655 /* 656 * SDRAMC Memory controller 657 */ 658 sdramc_sf: 659 tst r0, #SRAMC_SELF_FRESH_ACTIVE 660 beq sdramc_exit_sf 661 662 /* Active SDRAMC self-refresh mode */ 663 ldr r3, [r2, #AT91_SDRAMC_LPR] 664 str r3, .saved_sam9_lpr 665 bic r3, r3, #AT91_SDRAMC_LPCB 666 orr r3, r3, #AT91_SDRAMC_LPCB_SELF_REFRESH 667 str r3, [r2, #AT91_SDRAMC_LPR] 668 669 sdramc_exit_sf: 670 ldr r3, .saved_sam9_lpr 671 str r3, [r2, #AT91_SDRAMC_LPR] 672 673 exit_sramc_sf: 674 mov pc, lr 675 ENDPROC(at91_sramc_self_refresh) 676 677 .pmc_base: 678 .word 0 679 .sramc_base: 680 .word 0 681 .sramc1_base: 682 .word 0 683 .shdwc: 684 .word 0 685 .sfrbu: 686 .word 0 687 .memtype: 688 .word 0 689 .pm_mode: 690 .word 0 691 .mckr_offset: 692 .word 0 693 .pmc_version: 694 .word 0 695 .saved_mckr: 696 .word 0 697 .saved_pllar: 698 .word 0 699 .saved_sam9_lpr: 700 .word 0 701 .saved_sam9_lpr1: 702 .word 0 703 .saved_sam9_mdr: 704 .word 0 705 .saved_sam9_mdr1: 706 .word 0 707 .saved_osc_status: 708 .word 0 709 710 ENTRY(at91_pm_suspend_in_sram_sz) 711 .word .-at91_pm_suspend_in_sram 712