| /kernel/linux/linux-5.10/arch/powerpc/platforms/embedded6xx/ |
| H A D | ls_uart.c | 78 out_8(avr_addr + UART_FCR, UART_FCR_ENABLE_FIFO); /* enable FIFO */ in avr_uart_configure()
97 out_8(avr_addr + UART_FCR, UART_FCR_ENABLE_FIFO); /* enable FIFO */ in ls_uart_init()
98 out_8(avr_addr + UART_FCR, UART_FCR_ENABLE_FIFO | in ls_uart_init()
100 out_8(avr_addr + UART_FCR, 0); in ls_uart_init()
|
| /kernel/linux/linux-6.6/arch/powerpc/platforms/embedded6xx/ |
| H A D | ls_uart.c | 79 out_8(avr_addr + UART_FCR, UART_FCR_ENABLE_FIFO); /* enable FIFO */ in avr_uart_configure()
98 out_8(avr_addr + UART_FCR, UART_FCR_ENABLE_FIFO); /* enable FIFO */ in ls_uart_init()
99 out_8(avr_addr + UART_FCR, UART_FCR_ENABLE_FIFO | in ls_uart_init()
101 out_8(avr_addr + UART_FCR, 0); in ls_uart_init()
|
| /kernel/linux/linux-5.10/arch/powerpc/boot/ |
| H A D | ns16550.c | 22 #define UART_FCR 2 /* Out: FIFO Control Register */ macro
36 out_8(reg_base + (UART_FCR << reg_shift), 0x06); in ns16550_open()
|
| /kernel/linux/linux-6.6/arch/powerpc/boot/ |
| H A D | ns16550.c | 22 #define UART_FCR 2 /* Out: FIFO Control Register */ macro
36 out_8(reg_base + (UART_FCR << reg_shift), 0x06); in ns16550_open()
|
| /kernel/linux/linux-5.10/drivers/tty/serial/ |
| H A D | sunsu.c | 648 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); in sunsu_startup()
649 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | in sunsu_startup()
651 serial_outp(up, UART_FCR, 0); in sunsu_startup()
753 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | in sunsu_shutdown()
756 serial_outp(up, UART_FCR, 0); in sunsu_shutdown()
887 serial_outp(up, UART_FCR, fcr); /* set fcr */ in sunsu_change_speed()
893 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); in sunsu_change_speed()
895 serial_outp(up, UART_FCR, fcr); /* set fcr */ in sunsu_change_speed()
1097 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); in sunsu_autoconfig()
1127 serial_outp(up, UART_FCR, in sunsu_autoconfig()
[all...] |
| H A D | pxa.c | 353 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); in serial_pxa_startup()
354 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | in serial_pxa_startup()
356 serial_out(up, UART_FCR, 0); in serial_pxa_startup()
417 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | in serial_pxa_shutdown()
420 serial_out(up, UART_FCR, 0); in serial_pxa_shutdown()
542 serial_out(up, UART_FCR, fcr); in serial_pxa_set_termios()
|
| H A D | vr41xx_siu.c | 135 siu_write(port, UART_FCR, UART_FCR_ENABLE_FIFO); in siu_clear_fifo()
136 siu_write(port, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | in siu_clear_fifo()
138 siu_write(port, UART_FCR, 0); in siu_clear_fifo()
573 siu_write(port, UART_FCR, fcr); in siu_set_termios()
|
| /kernel/linux/linux-6.6/drivers/tty/serial/ |
| H A D | sunsu.c | 644 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); in sunsu_startup()
645 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | in sunsu_startup()
647 serial_outp(up, UART_FCR, 0); in sunsu_startup()
749 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO | in sunsu_shutdown()
752 serial_outp(up, UART_FCR, 0); in sunsu_shutdown()
881 serial_outp(up, UART_FCR, fcr); /* set fcr */ in sunsu_change_speed()
887 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); in sunsu_change_speed()
889 serial_outp(up, UART_FCR, fcr); /* set fcr */ in sunsu_change_speed()
1091 serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO); in sunsu_autoconfig()
1121 serial_outp(up, UART_FCR, in sunsu_autoconfig()
[all...] |
| H A D | pxa.c | 331 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); in serial_pxa_startup()
332 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | in serial_pxa_startup()
334 serial_out(up, UART_FCR, 0); in serial_pxa_startup()
395 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | in serial_pxa_shutdown()
398 serial_out(up, UART_FCR, 0); in serial_pxa_shutdown()
506 serial_out(up, UART_FCR, fcr); in serial_pxa_set_termios()
|
| /kernel/linux/linux-5.10/arch/powerpc/kernel/ |
| H A D | udbg_16550.c | 19 #define UART_FCR 2 macro
26 #define UART_IIR UART_FCR
121 udbg_uart_out(UART_FCR, 0x7); in udbg_uart_setup()
|
| /kernel/linux/linux-6.6/arch/powerpc/kernel/ |
| H A D | udbg_16550.c | 20 #define UART_FCR 2 macro
27 #define UART_IIR UART_FCR
122 udbg_uart_out(UART_FCR, 0x7); in udbg_uart_setup()
|
| /kernel/linux/linux-5.10/drivers/usb/serial/ |
| H A D | ark3116.c | 143 ark3116_write_reg(serial, UART_FCR, 0); in ark3116_port_probe()
278 ark3116_write_reg(serial, UART_FCR, 0); in ark3116_set_termios()
293 ark3116_write_reg(serial, UART_FCR, UART_FCR_DMA_SELECT); in ark3116_set_termios()
317 ark3116_write_reg(serial, UART_FCR, 0); in ark3116_close()
372 ark3116_write_reg(port->serial, UART_FCR, UART_FCR_DMA_SELECT); in ark3116_open()
|
| /kernel/linux/linux-6.6/drivers/usb/serial/ |
| H A D | ark3116.c | 143 ark3116_write_reg(serial, UART_FCR, 0); in ark3116_port_probe()
262 ark3116_write_reg(serial, UART_FCR, 0); in ark3116_set_termios()
277 ark3116_write_reg(serial, UART_FCR, UART_FCR_DMA_SELECT); in ark3116_set_termios()
301 ark3116_write_reg(serial, UART_FCR, 0); in ark3116_close()
356 ark3116_write_reg(port->serial, UART_FCR, UART_FCR_DMA_SELECT); in ark3116_open()
|
| /kernel/linux/linux-5.10/drivers/tty/serial/8250/ |
| H A D | 8250_ingenic.c | 117 early_out(port, UART_FCR, UART_FCR_UME | UART_FCR_CLEAR_XMIT | in ingenic_early_console_setup()
152 case UART_FCR: in ingenic_uart_serial_out()
193 case UART_FCR: in ingenic_uart_serial_in()
|
| H A D | 8250_port.c | 347 4, /* UART_FCR */
539 serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO); in serial8250_clear_fifos()
540 serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO | in serial8250_clear_fifos()
542 serial_out(p, UART_FCR, 0); in serial8250_clear_fifos()
552 serial_out(p, UART_FCR, p->fcr); in serial8250_clear_and_reinit_fifos()
825 old_fcr = serial_in(up, UART_FCR); in size_fifo()
827 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | in size_fifo()
840 serial_out(up, UART_FCR, old_fcr); in size_fifo()
1030 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | in autoconfig_16550a()
1033 serial_out(up, UART_FCR, in autoconfig_16550a()
[all...] |
| H A D | 8250_em.c | 34 case UART_FCR: /* FCR @ 0x0c (+1) */ in serial8250_em_serial_out()
|
| /kernel/linux/linux-6.6/drivers/tty/serial/8250/ |
| H A D | 8250_ingenic.c | 114 early_out(port, UART_FCR, UART_FCR_UME | UART_FCR_CLEAR_XMIT | in ingenic_earlycon_setup_tail()
176 case UART_FCR: in ingenic_uart_serial_out()
217 case UART_FCR: in ingenic_uart_serial_in()
|
| H A D | 8250_port.c | 494 serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO); in serial8250_clear_fifos()
495 serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO | in serial8250_clear_fifos()
497 serial_out(p, UART_FCR, 0); in serial8250_clear_fifos()
507 serial_out(p, UART_FCR, p->fcr); in serial8250_clear_and_reinit_fifos()
801 old_fcr = serial_in(up, UART_FCR); in size_fifo()
803 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | in size_fifo()
816 serial_out(up, UART_FCR, old_fcr); in size_fifo()
1009 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | in autoconfig_16550a()
1013 serial_out(up, UART_FCR, 0); in autoconfig_16550a()
1083 serial_out(up, UART_FCR, UART_FCR_ENABLE_FIF in autoconfig_16550a()
[all...] |
| H A D | 8250_rt288x.c | 31 [UART_FCR] = 4,
|
| /kernel/linux/linux-5.10/drivers/mmc/core/ |
| H A D | sdio_uart.c | 342 sdio_out(port, UART_FCR, fcr); in sdio_uart_change_speed()
622 sdio_out(port, UART_FCR, UART_FCR_ENABLE_FIFO); in sdio_uart_activate()
623 sdio_out(port, UART_FCR, UART_FCR_ENABLE_FIFO | in sdio_uart_activate()
625 sdio_out(port, UART_FCR, 0); in sdio_uart_activate()
699 sdio_out(port, UART_FCR, UART_FCR_ENABLE_FIFO | in sdio_uart_shutdown()
702 sdio_out(port, UART_FCR, 0); in sdio_uart_shutdown()
|
| /kernel/linux/linux-6.6/drivers/mmc/core/ |
| H A D | sdio_uart.c | 329 sdio_out(port, UART_FCR, fcr); in sdio_uart_change_speed()
608 sdio_out(port, UART_FCR, UART_FCR_ENABLE_FIFO); in sdio_uart_activate()
609 sdio_out(port, UART_FCR, UART_FCR_ENABLE_FIFO | in sdio_uart_activate()
611 sdio_out(port, UART_FCR, 0); in sdio_uart_activate()
685 sdio_out(port, UART_FCR, UART_FCR_ENABLE_FIFO | in sdio_uart_shutdown()
688 sdio_out(port, UART_FCR, 0); in sdio_uart_shutdown()
|
| /kernel/linux/linux-5.10/drivers/media/rc/ |
| H A D | sir_ir.c | 135 outb(UART_FCR_CLEAR_RCVR, io + UART_FCR); in sir_timeout()
302 outb(UART_FCR_ENABLE_FIFO, io + UART_FCR); in init_hardware()
|
| /kernel/linux/linux-5.10/drivers/tty/ |
| H A D | mxser.c | 803 outb(fcr, info->ioaddr + UART_FCR); /* set fcr */ in mxser_change_speed()
884 MOXA_MUST_FCR_GDA_MODE_ENABLE), info->ioaddr + UART_FCR); in mxser_activate()
887 info->ioaddr + UART_FCR); in mxser_activate()
984 info->ioaddr + UART_FCR); in mxser_shutdown_port()
987 info->ioaddr + UART_FCR); in mxser_shutdown_port()
1031 fcr = inb(info->ioaddr + UART_FCR); in mxser_flush_buffer()
1033 info->ioaddr + UART_FCR); in mxser_flush_buffer()
1034 outb(fcr, info->ioaddr + UART_FCR); in mxser_flush_buffer()
2106 outb(0x23, port->ioaddr + UART_FCR); in mxser_receive_chars()
2261 outb(0x27, port->ioaddr + UART_FCR); in mxser_interrupt()
[all...] |
| /kernel/linux/linux-5.10/arch/sh/include/asm/ |
| H A D | smc37c93x.h | 61 #define UART_FCR 0x4 /* FIFO Control Register (Write Only) */ macro
|
| /kernel/linux/linux-6.6/arch/sh/include/asm/ |
| H A D | smc37c93x.h | 61 #define UART_FCR 0x4 /* FIFO Control Register (Write Only) */ macro
|