| /kernel/linux/linux-5.10/drivers/scsi/pcmcia/ |
| H A D | sym53c500_cs.c | 88 #define CMD_REG 0x03 /* command register */ macro
229 outb(CHIP_RESET, io_port + CMD_REG); in SYM53C500_int_host_reset()
230 outb(SCSI_NOP, io_port + CMD_REG); /* required after reset */ in SYM53C500_int_host_reset()
231 outb(SCSI_RESET, io_port + CMD_REG); in SYM53C500_int_host_reset()
417 outb(FLUSH_FIFO, port_base + CMD_REG); in SYM53C500_intr()
419 outb(TRANSFER_INFO | DMA_OP, port_base + CMD_REG); in SYM53C500_intr()
436 outb(FLUSH_FIFO, port_base + CMD_REG); in SYM53C500_intr()
438 outb(TRANSFER_INFO | DMA_OP, port_base + CMD_REG); in SYM53C500_intr()
456 outb(FLUSH_FIFO, port_base + CMD_REG); in SYM53C500_intr()
457 outb(INIT_CMD_COMPLETE, port_base + CMD_REG); in SYM53C500_intr()
[all...] |
| /kernel/linux/linux-6.6/drivers/scsi/pcmcia/ |
| H A D | sym53c500_cs.c | 88 #define CMD_REG 0x03 /* command register */ macro
235 outb(CHIP_RESET, io_port + CMD_REG); in SYM53C500_int_host_reset()
236 outb(SCSI_NOP, io_port + CMD_REG); /* required after reset */ in SYM53C500_int_host_reset()
237 outb(SCSI_RESET, io_port + CMD_REG); in SYM53C500_int_host_reset()
424 outb(FLUSH_FIFO, port_base + CMD_REG); in SYM53C500_intr()
426 outb(TRANSFER_INFO | DMA_OP, port_base + CMD_REG); in SYM53C500_intr()
443 outb(FLUSH_FIFO, port_base + CMD_REG); in SYM53C500_intr()
445 outb(TRANSFER_INFO | DMA_OP, port_base + CMD_REG); in SYM53C500_intr()
463 outb(FLUSH_FIFO, port_base + CMD_REG); in SYM53C500_intr()
464 outb(INIT_CMD_COMPLETE, port_base + CMD_REG); in SYM53C500_intr()
[all...] |
| /kernel/linux/linux-5.10/drivers/clk/qcom/ |
| H A D | clk-rcg2.c | 23 #define CMD_REG 0x0 macro
69 ret = regmap_read(rcg->clkr.regmap, rcg->cmd_rcgr + CMD_REG, &cmd); in clk_rcg2_is_enabled()
107 ret = regmap_update_bits(rcg->clkr.regmap, rcg->cmd_rcgr + CMD_REG, in update_config()
114 ret = regmap_read(rcg->clkr.regmap, rcg->cmd_rcgr + CMD_REG, &cmd); in update_config()
824 ret = regmap_update_bits(rcg->clkr.regmap, rcg->cmd_rcgr + CMD_REG, in clk_rcg2_set_force_enable()
845 return regmap_update_bits(rcg->clkr.regmap, rcg->cmd_rcgr + CMD_REG, in clk_rcg2_clear_force_enable()
|
| /kernel/linux/linux-6.6/drivers/clk/qcom/ |
| H A D | clk-rcg2.c | 24 #define CMD_REG 0x0 macro
70 ret = regmap_read(rcg->clkr.regmap, rcg->cmd_rcgr + CMD_REG, &cmd); in clk_rcg2_is_enabled()
118 ret = regmap_update_bits(rcg->clkr.regmap, rcg->cmd_rcgr + CMD_REG, in update_config()
125 ret = regmap_read(rcg->clkr.regmap, rcg->cmd_rcgr + CMD_REG, &cmd); in update_config()
981 ret = regmap_update_bits(rcg->clkr.regmap, rcg->cmd_rcgr + CMD_REG, in clk_rcg2_set_force_enable()
1002 return regmap_update_bits(rcg->clkr.regmap, rcg->cmd_rcgr + CMD_REG, in clk_rcg2_clear_force_enable()
|
| /kernel/linux/linux-6.6/drivers/net/ieee802154/ |
| H A D | at86rf230.c | 317 .write_flag_mask = CMD_REG | CMD_WRITE,
318 .read_flag_mask = CMD_REG,
377 tx_buf[0] = (reg & CMD_REG_MASK) | CMD_REG; in at86rf230_async_read_reg()
391 ctx->buf[0] = (reg & CMD_REG_MASK) | CMD_REG | CMD_WRITE; in at86rf230_async_write_reg()
802 ctx->buf[0] = (RG_IRQ_STATUS & CMD_REG_MASK) | CMD_REG; in at86rf230_isr()
|
| H A D | at86rf230.h | 171 #define CMD_REG 0x80 macro
|
| /kernel/linux/linux-5.10/drivers/net/ieee802154/ |
| H A D | at86rf230.c | 328 .write_flag_mask = CMD_REG | CMD_WRITE,
329 .read_flag_mask = CMD_REG,
389 tx_buf[0] = (reg & CMD_REG_MASK) | CMD_REG; in at86rf230_async_read_reg()
403 ctx->buf[0] = (reg & CMD_REG_MASK) | CMD_REG | CMD_WRITE; in at86rf230_async_write_reg()
838 ctx->buf[0] = (RG_IRQ_STATUS & CMD_REG_MASK) | CMD_REG; in at86rf230_isr()
|
| H A D | at86rf230.h | 171 #define CMD_REG 0x80 macro
|
| /kernel/linux/linux-5.10/drivers/mtd/nand/raw/ |
| H A D | arasan-nand-controller.c | 38 #define CMD_REG 0x0C macro
248 writel_relaxed(nfc_op->cmd_reg, nfc->base + CMD_REG); in anfc_trigger_op()
|
| /kernel/linux/linux-6.6/drivers/mtd/nand/raw/ |
| H A D | arasan-nand-controller.c | 39 #define CMD_REG 0x0C macro
277 writel_relaxed(nfc_op->cmd_reg, nfc->base + CMD_REG); in anfc_trigger_op()
|