xref: /kernel/linux/linux-6.6/scripts/dtc/include-prefixes/arm64/actions/s900-bubblegum-96.dts

// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright (c) 2017 Andreas Färber
 */

/dts-v1/;

#include "s900.dtsi"

/ {
	compatible = "ucrobotics,bubblegum-96", "actions,s900";
	model = "Bubblegum-96";

	aliases {
		mmc0 = &mmc0;
		mmc1 = &mmc1;
		mmc2 = &mmc2;
		serial5 = &uart5;
	};

	chosen {
		stdout-path = "serial5:115200n8";
	};

	memory@0 {
		device_type = "memory";
		reg = <0x0 0x0 0x0 0x80000000>;
	};

	/* Fixed regulator used in the absence of PMIC */
	vcc_3v1: vcc-3v1 {
		compatible = "regulator-fixed";
		regulator-name = "fixed-3.1V";
		regulator-min-microvolt = <3100000>;
		regulator-max-microvolt = <3100000>;
		regulator-always-on;
	};

	/* Fixed regulator used in the absence of PMIC */
	sd_vcc: sd-vcc {
		compatible = "regulator-fixed";
		regulator-name = "fixed-3.1V";
		regulator-min-microvolt = <3100000>;
		regulator-max-microvolt = <3100000>;
		regulator-always-on;
	};
};

&i2c0 {
	status = "disabled";
	pinctrl-names = "default";
	pinctrl-0 = <&i2c0_default>;
};

&i2c1 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&i2c1_default>;
};

&i2c2 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&i2c2_default>;
};

/*
 * GPIO name legend: proper name = the GPIO line is used as GPIO
 *         NC = not connected (pin out but not routed from the chip to
 *              anything the board)
 *         "[PER]" = pin is muxed for [peripheral] (not GPIO)
 *         LSEC = Low Speed External Connector
 *         HSEC = High Speed External Connector
 *
 * Line names are taken from the schematic "Schematics Bubblegum96"
 * version v1.0
 *
 * For the lines routed to the external connectors the
 * lines are named after the 96Boards CE Specification 1.0,
 * Appendix "Expansion Connector Signal Description".
 *
 * When the 96Boards naming of a line and the schematic name of
 * the same line are in conflict, the 96Boards specification
 * takes precedence, which means that the external UART on the
 * LSEC is named UART0 while the schematic and SoC names this
 * UART2. Only exception is the I2C lines for which the schematic
 * naming has been preferred. This is only for the informational
 * lines i.e. "[FOO]", the GPIO named lines "GPIO-A" thru "GPIO-L"
 * are the only ones actually used for GPIO.
 */

&pinctrl {
	gpio-line-names =
		"GPIO-A", /* GPIO_0, LSEC pin 23 */
		"GPIO-B", /* GPIO_1, LSEC pin 24 */
		"GPIO-C", /* GPIO_2, LSEC pin 25 */
		"GPIO-D", /* GPIO_3, LSEC pin 26 */
		"GPIO-E", /* GPIO_4, LSEC pin 27 */
		"GPIO-F", /* GPIO_5, LSEC pin 28 */
		"GPIO-G", /* GPIO_6, LSEC pin 29 */
		"GPIO-H", /* GPIO_7, LSEC pin 30 */
		"GPIO-I", /* GPIO_8, LSEC pin 31 */
		"GPIO-J", /* GPIO_9, LSEC pin 32 */
		"NC", /* GPIO_10 */
		"NC", /* GPIO_11 */
		"SIRQ2_1V8", /* GPIO_12 */
		"PCM0_OUT", /* GPIO_13 */
		"WIFI_LED", /* GPIO_14 */
		"PCM0_SYNC", /* GPIO_15 */
		"PCM0_CLK", /* GPIO_16 */
		"PCM0_IN", /* GPIO_17 */
		"BT_LED", /* GPIO_18 */
		"LED0", /* GPIO_19 */
		"LED1", /* GPIO_20 */
		"JTAG_TCK", /* GPIO_21 */
		"JTAG_TMS", /* GPIO_22 */
		"JTAG_TDI", /* GPIO_23 */
		"JTAG_TDO", /* GPIO_24 */
		"[UART1_RxD]", /* GPIO_25, LSEC pin 13 */
		"NC", /* GPIO_26 */
		"[UART1_TxD]", /* GPIO_27, LSEC pin 11 */
		"SD0_D0", /* GPIO_28 */
		"SD0_D1", /* GPIO_29 */
		"SD0_D2", /* GPIO_30 */
		"SD0_D3", /* GPIO_31 */
		"SD1_D0", /* GPIO_32 */
		"SD1_D1", /* GPIO_33 */
		"SD1_D2", /* GPIO_34 */
		"SD1_D3", /* GPIO_35 */
		"SD0_CMD", /* GPIO_36 */
		"SD0_CLK", /* GPIO_37 */
		"SD1_CMD", /* GPIO_38 */
		"SD1_CLK", /* GPIO_39 */
		"SPI0_SCLK", /* GPIO_40, LSEC pin 8 */
		"SPI0_CS", /* GPIO_41, LSEC pin 12 */
		"SPI0_DIN", /* GPIO_42, LSEC pin 10 */
		"SPI0_DOUT", /* GPIO_43, LSEC pin 14 */
		"I2C5_SDATA", /* GPIO_44, HSEC pin 36 */
		"I2C5_SCLK", /* GPIO_45, HSEC pin 38 */
		"UART0_RX", /* GPIO_46, LSEC pin 7 */
		"UART0_TX", /* GPIO_47, LSEC pin 5 */
		"UART0_RTSB", /* GPIO_48, LSEC pin 9 */
		"UART0_CTSB", /* GPIO_49, LSEC pin 3 */
		"I2C4_SCLK", /* GPIO_50, HSEC pin 32 */
		"I2C4_SDATA", /* GPIO_51, HSEC pin 34 */
		"I2C0_SCLK", /* GPIO_52 */
		"I2C0_SDATA", /* GPIO_53 */
		"I2C1_SCLK", /* GPIO_54, LSEC pin 15 */
		"I2C1_SDATA", /* GPIO_55, LSEC pin 17 */
		"I2C2_SCLK", /* GPIO_56, LSEC pin 19 */
		"I2C2_SDATA", /* GPIO_57, LSEC pin 21 */
		"CSI0_DN0", /* GPIO_58, HSEC pin 10 */
		"CSI0_DP0", /* GPIO_59, HSEC pin 8 */
		"CSI0_DN1", /* GPIO_60, HSEC pin 16 */
		"CSI0_DP1", /* GPIO_61, HSEC pin 14 */
		"CSI0_CN", /* GPIO_62, HSEC pin 4 */
		"CSI0_CP", /* GPIO_63, HSEC pin 2 */
		"CSI0_DN2", /* GPIO_64, HSEC pin 22 */
		"CSI0_DP2", /* GPIO_65, HSEC pin 20 */
		"CSI0_DN3", /* GPIO_66, HSEC pin 28 */
		"CSI0_DP3", /* GPIO_67, HSEC pin 26 */
		"[CLK0]", /* GPIO_68, HSEC pin 15 */
		"CSI1_DN0", /* GPIO_69, HSEC pin 44 */
		"CSI1_DP0", /* GPIO_70, HSEC pin 42 */
		"CSI1_DN1", /* GPIO_71, HSEC pin 50 */
		"CSI1_DP1", /* GPIO_72, HSEC pin 48 */
		"CSI1_CN", /* GPIO_73, HSEC pin 56 */
		"CSI1_CP", /* GPIO_74, HSEC pin 54 */
		"[CLK1]", /* GPIO_75, HSEC pin 17 */
		"[GPIOD0]", /* GPIO_76 */
		"[GPIOD1]", /* GPIO_77 */
		"BT_RST_N", /* GPIO_78 */
		"EXT_DC_EN", /* GPIO_79 */
		"[PCM_DI]", /* GPIO_80, LSEC pin 22 */
		"[PCM_DO]", /* GPIO_81, LSEC pin 20 */
		"[PCM_CLK]", /* GPIO_82, LSEC pin 18 */
		"[PCM_FS]", /* GPIO_83, LSEC pin 16 */
		"WAKE_BT", /* GPIO_84 */
		"WL_REG_ON", /* GPIO_85 */
		"NC", /* GPIO_86 */
		"NC", /* GPIO_87 */
		"NC", /* GPIO_88 */
		"NC", /* GPIO_89 */
		"NC", /* GPIO_90 */
		"WIFI_WAKE", /* GPIO_91 */
		"BT_WAKE", /* GPIO_92 */
		"NC", /* GPIO_93 */
		"OTG_EN2", /* GPIO_94 */
		"OTG_EN", /* GPIO_95 */
		"DSI_DP3", /* GPIO_96, HSEC pin 45 */
		"DSI_DN3", /* GPIO_97, HSEC pin 47 */
		"DSI_DP1", /* GPIO_98, HSEC pin 33 */
		"DSI_DN1", /* GPIO_99, HSEC pin 35 */
		"DSI_CP", /* GPIO_100, HSEC pin 21 */
		"DSI_CN", /* GPIO_101, HSEC pin 23 */
		"DSI_DP0", /* GPIO_102, HSEC pin 27 */
		"DSI_DN0", /* GPIO_103, HSEC pin 29 */
		"DSI_DP2", /* GPIO_104, HSEC pin 39 */
		"DSI_DN2", /* GPIO_105, HSEC pin 41 */
		"N0_D0", /* GPIO_106 */
		"N0_D1", /* GPIO_107 */
		"N0_D2", /* GPIO_108 */
		"N0_D3", /* GPIO_109 */
		"N0_D4", /* GPIO_110 */
		"N0_D5", /* GPIO_111 */
		"N0_D6", /* GPIO_112 */
		"N0_D7", /* GPIO_113 */
		"N0_DQS", /* GPIO_114 */
		"N0_DQSN", /* GPIO_115 */
		"NC", /* GPIO_116 */
		"NC", /* GPIO_117 */
		"NC", /* GPIO_118 */
		"N0_CEB1", /* GPIO_119 */
		"CARD_DT", /* GPIO_120 */
		"N0_CEB3", /* GPIO_121 */
		"SD_DAT0", /* GPIO_122, HSEC pin 1 */
		"SD_DAT1", /* GPIO_123, HSEC pin 3 */
		"SD_DAT2", /* GPIO_124, HSEC pin 5 */
		"SD_DAT3", /* GPIO_125, HSEC pin 7 */
		"NC", /* GPIO_126 */
		"NC", /* GPIO_127 */
		"[PWR_BTN_N]", /* GPIO_128, LSEC pin 4 */
		"[RST_BTN_N]", /* GPIO_129, LSEC pin 6 */
		"NC", /* GPIO_130 */
		"SD_CMD", /* GPIO_131 */
		"GPIO-L", /* GPIO_132, LSEC pin 34 */
		"GPIO-K", /* GPIO_133, LSEC pin 33 */
		"NC", /* GPIO_134 */
		"SD_SCLK", /* GPIO_135 */
		"NC", /* GPIO_136 */
		"JTAG_TRST", /* GPIO_137 */
		"I2C3_SCLK", /* GPIO_138 */
		"LED2", /* GPIO_139 */
		"LED3", /* GPIO_140 */
		"I2C3_SDATA", /* GPIO_141 */
		"UART3_RX", /* GPIO_142 */
		"UART3_TX", /* GPIO_143 */
		"UART3_RTSB", /* GPIO_144 */
		"UART3_CTSB"; /* GPIO_145 */

	i2c0_default: i2c0-default {
		pinmux {
			groups = "i2c0_mfp";
			function = "i2c0";
		};
		pinconf {
			pins = "i2c0_sclk", "i2c0_sdata";
			bias-pull-up;
		};
	};

	i2c1_default: i2c1-default {
		pinconf {
			pins = "i2c1_sclk", "i2c1_sdata";
			bias-pull-up;
		};
	};

	i2c2_default: i2c2-default {
		pinconf {
			pins = "i2c2_sclk", "i2c2_sdata";
			bias-pull-up;
		};
	};

	mmc0_default: mmc0_default {
		pinmux {
			groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp",
				 "sd0_cmd_mfp", "sd0_clk_mfp";
			function = "sd0";
		};
	};

	mmc2_default: mmc2_default {
		pinmux {
			groups = "nand0_d0_ceb3_mfp";
			function = "sd2";
		};
	};
};

/* uSD */
&mmc0 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&mmc0_default>;
	no-sdio;
	no-mmc;
	no-1-8-v;
	cd-gpios = <&pinctrl 120 GPIO_ACTIVE_LOW>;
	bus-width = <4>;
	vmmc-supply = <&sd_vcc>;
	vqmmc-supply = <&sd_vcc>;
};

/* eMMC */
&mmc2 {
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&mmc2_default>;
	no-sdio;
	no-sd;
	non-removable;
	bus-width = <8>;
	vmmc-supply = <&vcc_3v1>;
};

&timer {
	clocks = <&hosc>;
};

&uart5 {
	status = "okay";
};