1// SPDX-License-Identifier: GPL-2.0-or-later 2/* 3 * Broadcom Starfighter 2 DSA switch driver 4 * 5 * Copyright (C) 2014, Broadcom Corporation 6 */ 7 8#include <linux/list.h> 9#include <linux/module.h> 10#include <linux/netdevice.h> 11#include <linux/interrupt.h> 12#include <linux/platform_device.h> 13#include <linux/phy.h> 14#include <linux/phy_fixed.h> 15#include <linux/phylink.h> 16#include <linux/mii.h> 17#include <linux/clk.h> 18#include <linux/of.h> 19#include <linux/of_irq.h> 20#include <linux/of_address.h> 21#include <linux/of_net.h> 22#include <linux/of_mdio.h> 23#include <net/dsa.h> 24#include <linux/ethtool.h> 25#include <linux/if_bridge.h> 26#include <linux/brcmphy.h> 27#include <linux/etherdevice.h> 28#include <linux/platform_data/b53.h> 29 30#include "bcm_sf2.h" 31#include "bcm_sf2_regs.h" 32#include "b53/b53_priv.h" 33#include "b53/b53_regs.h" 34 35static u16 bcm_sf2_reg_rgmii_cntrl(struct bcm_sf2_priv *priv, int port) 36{ 37 switch (priv->type) { 38 case BCM4908_DEVICE_ID: 39 switch (port) { 40 case 7: 41 return REG_RGMII_11_CNTRL; 42 default: 43 break; 44 } 45 break; 46 default: 47 switch (port) { 48 case 0: 49 return REG_RGMII_0_CNTRL; 50 case 1: 51 return REG_RGMII_1_CNTRL; 52 case 2: 53 return REG_RGMII_2_CNTRL; 54 default: 55 break; 56 } 57 } 58 59 WARN_ONCE(1, "Unsupported port %d\n", port); 60 61 /* RO fallback reg */ 62 return REG_SWITCH_STATUS; 63} 64 65static u16 bcm_sf2_reg_led_base(struct bcm_sf2_priv *priv, int port) 66{ 67 switch (port) { 68 case 0: 69 return REG_LED_0_CNTRL; 70 case 1: 71 return REG_LED_1_CNTRL; 72 case 2: 73 return REG_LED_2_CNTRL; 74 } 75 76 switch (priv->type) { 77 case BCM4908_DEVICE_ID: 78 switch (port) { 79 case 3: 80 return REG_LED_3_CNTRL; 81 case 7: 82 return REG_LED_4_CNTRL; 83 default: 84 break; 85 } 86 break; 87 default: 88 break; 89 } 90 91 WARN_ONCE(1, "Unsupported port %d\n", port); 92 93 /* RO fallback reg */ 94 return REG_SWITCH_STATUS; 95} 96 97static u32 bcm_sf2_port_override_offset(struct bcm_sf2_priv *priv, int port) 98{ 99 switch (priv->type) { 100 case BCM4908_DEVICE_ID: 101 case BCM7445_DEVICE_ID: 102 return port == 8 ? CORE_STS_OVERRIDE_IMP : 103 CORE_STS_OVERRIDE_GMIIP_PORT(port); 104 case BCM7278_DEVICE_ID: 105 return port == 8 ? CORE_STS_OVERRIDE_IMP2 : 106 CORE_STS_OVERRIDE_GMIIP2_PORT(port); 107 default: 108 WARN_ONCE(1, "Unsupported device: %d\n", priv->type); 109 } 110 111 /* RO fallback register */ 112 return REG_SWITCH_STATUS; 113} 114 115/* Return the number of active ports, not counting the IMP (CPU) port */ 116static unsigned int bcm_sf2_num_active_ports(struct dsa_switch *ds) 117{ 118 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 119 unsigned int port, count = 0; 120 121 for (port = 0; port < ds->num_ports; port++) { 122 if (dsa_is_cpu_port(ds, port)) 123 continue; 124 if (priv->port_sts[port].enabled) 125 count++; 126 } 127 128 return count; 129} 130 131static void bcm_sf2_recalc_clock(struct dsa_switch *ds) 132{ 133 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 134 unsigned long new_rate; 135 unsigned int ports_active; 136 /* Frequenty in Mhz */ 137 static const unsigned long rate_table[] = { 138 59220000, 139 60820000, 140 62500000, 141 62500000, 142 }; 143 144 ports_active = bcm_sf2_num_active_ports(ds); 145 if (ports_active == 0 || !priv->clk_mdiv) 146 return; 147 148 /* If we overflow our table, just use the recommended operational 149 * frequency 150 */ 151 if (ports_active > ARRAY_SIZE(rate_table)) 152 new_rate = 90000000; 153 else 154 new_rate = rate_table[ports_active - 1]; 155 clk_set_rate(priv->clk_mdiv, new_rate); 156} 157 158static void bcm_sf2_imp_setup(struct dsa_switch *ds, int port) 159{ 160 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 161 unsigned int i; 162 u32 reg; 163 164 /* Enable the port memories */ 165 reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL); 166 reg &= ~P_TXQ_PSM_VDD(port); 167 core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL); 168 169 /* Enable forwarding */ 170 core_writel(priv, SW_FWDG_EN, CORE_SWMODE); 171 172 /* Enable IMP port in dumb mode */ 173 reg = core_readl(priv, CORE_SWITCH_CTRL); 174 reg |= MII_DUMB_FWDG_EN; 175 core_writel(priv, reg, CORE_SWITCH_CTRL); 176 177 /* Configure Traffic Class to QoS mapping, allow each priority to map 178 * to a different queue number 179 */ 180 reg = core_readl(priv, CORE_PORT_TC2_QOS_MAP_PORT(port)); 181 for (i = 0; i < SF2_NUM_EGRESS_QUEUES; i++) 182 reg |= i << (PRT_TO_QID_SHIFT * i); 183 core_writel(priv, reg, CORE_PORT_TC2_QOS_MAP_PORT(port)); 184 185 b53_brcm_hdr_setup(ds, port); 186 187 if (port == 8) { 188 /* Enable Broadcast, Multicast, Unicast forwarding to IMP port */ 189 reg = core_readl(priv, CORE_IMP_CTL); 190 reg |= (RX_BCST_EN | RX_MCST_EN | RX_UCST_EN); 191 reg &= ~(RX_DIS | TX_DIS); 192 core_writel(priv, reg, CORE_IMP_CTL); 193 } else { 194 reg = core_readl(priv, CORE_G_PCTL_PORT(port)); 195 reg &= ~(RX_DIS | TX_DIS); 196 core_writel(priv, reg, CORE_G_PCTL_PORT(port)); 197 } 198 199 priv->port_sts[port].enabled = true; 200} 201 202static void bcm_sf2_gphy_enable_set(struct dsa_switch *ds, bool enable) 203{ 204 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 205 u32 reg; 206 207 reg = reg_readl(priv, REG_SPHY_CNTRL); 208 if (enable) { 209 reg |= PHY_RESET; 210 reg &= ~(EXT_PWR_DOWN | IDDQ_BIAS | IDDQ_GLOBAL_PWR | CK25_DIS); 211 reg_writel(priv, reg, REG_SPHY_CNTRL); 212 udelay(21); 213 reg = reg_readl(priv, REG_SPHY_CNTRL); 214 reg &= ~PHY_RESET; 215 } else { 216 reg |= EXT_PWR_DOWN | IDDQ_BIAS | PHY_RESET; 217 reg_writel(priv, reg, REG_SPHY_CNTRL); 218 mdelay(1); 219 reg |= CK25_DIS; 220 } 221 reg_writel(priv, reg, REG_SPHY_CNTRL); 222 223 /* Use PHY-driven LED signaling */ 224 if (!enable) { 225 u16 led_ctrl = bcm_sf2_reg_led_base(priv, 0); 226 227 if (priv->type == BCM7278_DEVICE_ID || 228 priv->type == BCM7445_DEVICE_ID) { 229 reg = reg_led_readl(priv, led_ctrl, 0); 230 reg |= LED_CNTRL_SPDLNK_SRC_SEL; 231 reg_led_writel(priv, reg, led_ctrl, 0); 232 } 233 } 234} 235 236static inline void bcm_sf2_port_intr_enable(struct bcm_sf2_priv *priv, 237 int port) 238{ 239 unsigned int off; 240 241 switch (port) { 242 case 7: 243 off = P7_IRQ_OFF; 244 break; 245 case 0: 246 /* Port 0 interrupts are located on the first bank */ 247 intrl2_0_mask_clear(priv, P_IRQ_MASK(P0_IRQ_OFF)); 248 return; 249 default: 250 off = P_IRQ_OFF(port); 251 break; 252 } 253 254 intrl2_1_mask_clear(priv, P_IRQ_MASK(off)); 255} 256 257static inline void bcm_sf2_port_intr_disable(struct bcm_sf2_priv *priv, 258 int port) 259{ 260 unsigned int off; 261 262 switch (port) { 263 case 7: 264 off = P7_IRQ_OFF; 265 break; 266 case 0: 267 /* Port 0 interrupts are located on the first bank */ 268 intrl2_0_mask_set(priv, P_IRQ_MASK(P0_IRQ_OFF)); 269 intrl2_0_writel(priv, P_IRQ_MASK(P0_IRQ_OFF), INTRL2_CPU_CLEAR); 270 return; 271 default: 272 off = P_IRQ_OFF(port); 273 break; 274 } 275 276 intrl2_1_mask_set(priv, P_IRQ_MASK(off)); 277 intrl2_1_writel(priv, P_IRQ_MASK(off), INTRL2_CPU_CLEAR); 278} 279 280static int bcm_sf2_port_setup(struct dsa_switch *ds, int port, 281 struct phy_device *phy) 282{ 283 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 284 unsigned int i; 285 u32 reg; 286 287 if (!dsa_is_user_port(ds, port)) 288 return 0; 289 290 priv->port_sts[port].enabled = true; 291 292 bcm_sf2_recalc_clock(ds); 293 294 /* Clear the memory power down */ 295 reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL); 296 reg &= ~P_TXQ_PSM_VDD(port); 297 core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL); 298 299 /* Enable Broadcom tags for that port if requested */ 300 if (priv->brcm_tag_mask & BIT(port)) 301 b53_brcm_hdr_setup(ds, port); 302 303 /* Configure Traffic Class to QoS mapping, allow each priority to map 304 * to a different queue number 305 */ 306 reg = core_readl(priv, CORE_PORT_TC2_QOS_MAP_PORT(port)); 307 for (i = 0; i < SF2_NUM_EGRESS_QUEUES; i++) 308 reg |= i << (PRT_TO_QID_SHIFT * i); 309 core_writel(priv, reg, CORE_PORT_TC2_QOS_MAP_PORT(port)); 310 311 /* Re-enable the GPHY and re-apply workarounds */ 312 if (priv->int_phy_mask & 1 << port && priv->hw_params.num_gphy == 1) { 313 bcm_sf2_gphy_enable_set(ds, true); 314 if (phy) { 315 /* if phy_stop() has been called before, phy 316 * will be in halted state, and phy_start() 317 * will call resume. 318 * 319 * the resume path does not configure back 320 * autoneg settings, and since we hard reset 321 * the phy manually here, we need to reset the 322 * state machine also. 323 */ 324 phy->state = PHY_READY; 325 phy_init_hw(phy); 326 } 327 } 328 329 /* Enable MoCA port interrupts to get notified */ 330 if (port == priv->moca_port) 331 bcm_sf2_port_intr_enable(priv, port); 332 333 /* Set per-queue pause threshold to 32 */ 334 core_writel(priv, 32, CORE_TXQ_THD_PAUSE_QN_PORT(port)); 335 336 /* Set ACB threshold to 24 */ 337 for (i = 0; i < SF2_NUM_EGRESS_QUEUES; i++) { 338 reg = acb_readl(priv, ACB_QUEUE_CFG(port * 339 SF2_NUM_EGRESS_QUEUES + i)); 340 reg &= ~XOFF_THRESHOLD_MASK; 341 reg |= 24; 342 acb_writel(priv, reg, ACB_QUEUE_CFG(port * 343 SF2_NUM_EGRESS_QUEUES + i)); 344 } 345 346 return b53_enable_port(ds, port, phy); 347} 348 349static void bcm_sf2_port_disable(struct dsa_switch *ds, int port) 350{ 351 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 352 u32 reg; 353 354 /* Disable learning while in WoL mode */ 355 if (priv->wol_ports_mask & (1 << port)) { 356 reg = core_readl(priv, CORE_DIS_LEARN); 357 reg |= BIT(port); 358 core_writel(priv, reg, CORE_DIS_LEARN); 359 return; 360 } 361 362 if (port == priv->moca_port) 363 bcm_sf2_port_intr_disable(priv, port); 364 365 if (priv->int_phy_mask & 1 << port && priv->hw_params.num_gphy == 1) 366 bcm_sf2_gphy_enable_set(ds, false); 367 368 b53_disable_port(ds, port); 369 370 /* Power down the port memory */ 371 reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL); 372 reg |= P_TXQ_PSM_VDD(port); 373 core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL); 374 375 priv->port_sts[port].enabled = false; 376 377 bcm_sf2_recalc_clock(ds); 378} 379 380 381static int bcm_sf2_sw_indir_rw(struct bcm_sf2_priv *priv, int op, int addr, 382 int regnum, u16 val) 383{ 384 int ret = 0; 385 u32 reg; 386 387 reg = reg_readl(priv, REG_SWITCH_CNTRL); 388 reg |= MDIO_MASTER_SEL; 389 reg_writel(priv, reg, REG_SWITCH_CNTRL); 390 391 /* Page << 8 | offset */ 392 reg = 0x70; 393 reg <<= 2; 394 core_writel(priv, addr, reg); 395 396 /* Page << 8 | offset */ 397 reg = 0x80 << 8 | regnum << 1; 398 reg <<= 2; 399 400 if (op) 401 ret = core_readl(priv, reg); 402 else 403 core_writel(priv, val, reg); 404 405 reg = reg_readl(priv, REG_SWITCH_CNTRL); 406 reg &= ~MDIO_MASTER_SEL; 407 reg_writel(priv, reg, REG_SWITCH_CNTRL); 408 409 return ret & 0xffff; 410} 411 412static int bcm_sf2_sw_mdio_read(struct mii_bus *bus, int addr, int regnum) 413{ 414 struct bcm_sf2_priv *priv = bus->priv; 415 416 /* Intercept reads from Broadcom pseudo-PHY address, else, send 417 * them to our master MDIO bus controller 418 */ 419 if (addr == BRCM_PSEUDO_PHY_ADDR && priv->indir_phy_mask & BIT(addr)) 420 return bcm_sf2_sw_indir_rw(priv, 1, addr, regnum, 0); 421 else 422 return mdiobus_read_nested(priv->master_mii_bus, addr, regnum); 423} 424 425static int bcm_sf2_sw_mdio_write(struct mii_bus *bus, int addr, int regnum, 426 u16 val) 427{ 428 struct bcm_sf2_priv *priv = bus->priv; 429 430 /* Intercept writes to the Broadcom pseudo-PHY address, else, 431 * send them to our master MDIO bus controller 432 */ 433 if (addr == BRCM_PSEUDO_PHY_ADDR && priv->indir_phy_mask & BIT(addr)) 434 return bcm_sf2_sw_indir_rw(priv, 0, addr, regnum, val); 435 else 436 return mdiobus_write_nested(priv->master_mii_bus, addr, 437 regnum, val); 438} 439 440static irqreturn_t bcm_sf2_switch_0_isr(int irq, void *dev_id) 441{ 442 struct dsa_switch *ds = dev_id; 443 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 444 445 priv->irq0_stat = intrl2_0_readl(priv, INTRL2_CPU_STATUS) & 446 ~priv->irq0_mask; 447 intrl2_0_writel(priv, priv->irq0_stat, INTRL2_CPU_CLEAR); 448 449 return IRQ_HANDLED; 450} 451 452static irqreturn_t bcm_sf2_switch_1_isr(int irq, void *dev_id) 453{ 454 struct dsa_switch *ds = dev_id; 455 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 456 457 priv->irq1_stat = intrl2_1_readl(priv, INTRL2_CPU_STATUS) & 458 ~priv->irq1_mask; 459 intrl2_1_writel(priv, priv->irq1_stat, INTRL2_CPU_CLEAR); 460 461 if (priv->irq1_stat & P_LINK_UP_IRQ(P7_IRQ_OFF)) { 462 priv->port_sts[7].link = true; 463 dsa_port_phylink_mac_change(ds, 7, true); 464 } 465 if (priv->irq1_stat & P_LINK_DOWN_IRQ(P7_IRQ_OFF)) { 466 priv->port_sts[7].link = false; 467 dsa_port_phylink_mac_change(ds, 7, false); 468 } 469 470 return IRQ_HANDLED; 471} 472 473static int bcm_sf2_sw_rst(struct bcm_sf2_priv *priv) 474{ 475 unsigned int timeout = 1000; 476 u32 reg; 477 int ret; 478 479 /* The watchdog reset does not work on 7278, we need to hit the 480 * "external" reset line through the reset controller. 481 */ 482 if (priv->type == BCM7278_DEVICE_ID) { 483 ret = reset_control_assert(priv->rcdev); 484 if (ret) 485 return ret; 486 487 return reset_control_deassert(priv->rcdev); 488 } 489 490 reg = core_readl(priv, CORE_WATCHDOG_CTRL); 491 reg |= SOFTWARE_RESET | EN_CHIP_RST | EN_SW_RESET; 492 core_writel(priv, reg, CORE_WATCHDOG_CTRL); 493 494 do { 495 reg = core_readl(priv, CORE_WATCHDOG_CTRL); 496 if (!(reg & SOFTWARE_RESET)) 497 break; 498 499 usleep_range(1000, 2000); 500 } while (timeout-- > 0); 501 502 if (timeout == 0) 503 return -ETIMEDOUT; 504 505 return 0; 506} 507 508static void bcm_sf2_crossbar_setup(struct bcm_sf2_priv *priv) 509{ 510 struct device *dev = priv->dev->ds->dev; 511 int shift; 512 u32 mask; 513 u32 reg; 514 int i; 515 516 mask = BIT(priv->num_crossbar_int_ports) - 1; 517 518 reg = reg_readl(priv, REG_CROSSBAR); 519 switch (priv->type) { 520 case BCM4908_DEVICE_ID: 521 shift = CROSSBAR_BCM4908_INT_P7 * priv->num_crossbar_int_ports; 522 reg &= ~(mask << shift); 523 if (0) /* FIXME */ 524 reg |= CROSSBAR_BCM4908_EXT_SERDES << shift; 525 else if (priv->int_phy_mask & BIT(7)) 526 reg |= CROSSBAR_BCM4908_EXT_GPHY4 << shift; 527 else if (phy_interface_mode_is_rgmii(priv->port_sts[7].mode)) 528 reg |= CROSSBAR_BCM4908_EXT_RGMII << shift; 529 else if (WARN(1, "Invalid port mode\n")) 530 return; 531 break; 532 default: 533 return; 534 } 535 reg_writel(priv, reg, REG_CROSSBAR); 536 537 reg = reg_readl(priv, REG_CROSSBAR); 538 for (i = 0; i < priv->num_crossbar_int_ports; i++) { 539 shift = i * priv->num_crossbar_int_ports; 540 541 dev_dbg(dev, "crossbar int port #%d - ext port #%d\n", i, 542 (reg >> shift) & mask); 543 } 544} 545 546static void bcm_sf2_intr_disable(struct bcm_sf2_priv *priv) 547{ 548 intrl2_0_mask_set(priv, 0xffffffff); 549 intrl2_0_writel(priv, 0xffffffff, INTRL2_CPU_CLEAR); 550 intrl2_1_mask_set(priv, 0xffffffff); 551 intrl2_1_writel(priv, 0xffffffff, INTRL2_CPU_CLEAR); 552} 553 554static void bcm_sf2_identify_ports(struct bcm_sf2_priv *priv, 555 struct device_node *dn) 556{ 557 struct device *dev = priv->dev->ds->dev; 558 struct bcm_sf2_port_status *port_st; 559 struct device_node *port; 560 unsigned int port_num; 561 struct property *prop; 562 int err; 563 564 priv->moca_port = -1; 565 566 for_each_available_child_of_node(dn, port) { 567 if (of_property_read_u32(port, "reg", &port_num)) 568 continue; 569 570 if (port_num >= DSA_MAX_PORTS) { 571 dev_err(dev, "Invalid port number %d\n", port_num); 572 continue; 573 } 574 575 port_st = &priv->port_sts[port_num]; 576 577 /* Internal PHYs get assigned a specific 'phy-mode' property 578 * value: "internal" to help flag them before MDIO probing 579 * has completed, since they might be turned off at that 580 * time 581 */ 582 err = of_get_phy_mode(port, &port_st->mode); 583 if (err) 584 continue; 585 586 if (port_st->mode == PHY_INTERFACE_MODE_INTERNAL) 587 priv->int_phy_mask |= 1 << port_num; 588 589 if (port_st->mode == PHY_INTERFACE_MODE_MOCA) 590 priv->moca_port = port_num; 591 592 if (of_property_read_bool(port, "brcm,use-bcm-hdr")) 593 priv->brcm_tag_mask |= 1 << port_num; 594 595 /* Ensure that port 5 is not picked up as a DSA CPU port 596 * flavour but a regular port instead. We should be using 597 * devlink to be able to set the port flavour. 598 */ 599 if (port_num == 5 && priv->type == BCM7278_DEVICE_ID) { 600 prop = of_find_property(port, "ethernet", NULL); 601 if (prop) 602 of_remove_property(port, prop); 603 } 604 } 605} 606 607static int bcm_sf2_mdio_register(struct dsa_switch *ds) 608{ 609 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 610 struct device_node *dn, *child; 611 struct phy_device *phydev; 612 struct property *prop; 613 static int index; 614 int err, reg; 615 616 /* Find our integrated MDIO bus node */ 617 dn = of_find_compatible_node(NULL, NULL, "brcm,unimac-mdio"); 618 priv->master_mii_bus = of_mdio_find_bus(dn); 619 if (!priv->master_mii_bus) { 620 err = -EPROBE_DEFER; 621 goto err_of_node_put; 622 } 623 624 priv->master_mii_dn = dn; 625 626 priv->slave_mii_bus = mdiobus_alloc(); 627 if (!priv->slave_mii_bus) { 628 err = -ENOMEM; 629 goto err_put_master_mii_bus_dev; 630 } 631 632 priv->slave_mii_bus->priv = priv; 633 priv->slave_mii_bus->name = "sf2 slave mii"; 634 priv->slave_mii_bus->read = bcm_sf2_sw_mdio_read; 635 priv->slave_mii_bus->write = bcm_sf2_sw_mdio_write; 636 snprintf(priv->slave_mii_bus->id, MII_BUS_ID_SIZE, "sf2-%d", 637 index++); 638 priv->slave_mii_bus->dev.of_node = dn; 639 640 /* Include the pseudo-PHY address to divert reads towards our 641 * workaround. This is only required for 7445D0, since 7445E0 642 * disconnects the internal switch pseudo-PHY such that we can use the 643 * regular SWITCH_MDIO master controller instead. 644 * 645 * Here we flag the pseudo PHY as needing special treatment and would 646 * otherwise make all other PHY read/writes go to the master MDIO bus 647 * controller that comes with this switch backed by the "mdio-unimac" 648 * driver. 649 */ 650 if (of_machine_is_compatible("brcm,bcm7445d0")) 651 priv->indir_phy_mask |= (1 << BRCM_PSEUDO_PHY_ADDR) | (1 << 0); 652 else 653 priv->indir_phy_mask = 0; 654 655 ds->phys_mii_mask = priv->indir_phy_mask; 656 ds->slave_mii_bus = priv->slave_mii_bus; 657 priv->slave_mii_bus->parent = ds->dev->parent; 658 priv->slave_mii_bus->phy_mask = ~priv->indir_phy_mask; 659 660 /* We need to make sure that of_phy_connect() will not work by 661 * removing the 'phandle' and 'linux,phandle' properties and 662 * unregister the existing PHY device that was already registered. 663 */ 664 for_each_available_child_of_node(dn, child) { 665 if (of_property_read_u32(child, "reg", ®) || 666 reg >= PHY_MAX_ADDR) 667 continue; 668 669 if (!(priv->indir_phy_mask & BIT(reg))) 670 continue; 671 672 prop = of_find_property(child, "phandle", NULL); 673 if (prop) 674 of_remove_property(child, prop); 675 676 prop = of_find_property(child, "linux,phandle", NULL); 677 if (prop) 678 of_remove_property(child, prop); 679 680 phydev = of_phy_find_device(child); 681 if (phydev) 682 phy_device_remove(phydev); 683 } 684 685 err = mdiobus_register(priv->slave_mii_bus); 686 if (err && dn) 687 goto err_free_slave_mii_bus; 688 689 return 0; 690 691err_free_slave_mii_bus: 692 mdiobus_free(priv->slave_mii_bus); 693err_put_master_mii_bus_dev: 694 put_device(&priv->master_mii_bus->dev); 695err_of_node_put: 696 of_node_put(dn); 697 return err; 698} 699 700static void bcm_sf2_mdio_unregister(struct bcm_sf2_priv *priv) 701{ 702 mdiobus_unregister(priv->slave_mii_bus); 703 mdiobus_free(priv->slave_mii_bus); 704 put_device(&priv->master_mii_bus->dev); 705 of_node_put(priv->master_mii_dn); 706} 707 708static u32 bcm_sf2_sw_get_phy_flags(struct dsa_switch *ds, int port) 709{ 710 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 711 712 /* The BCM7xxx PHY driver expects to find the integrated PHY revision 713 * in bits 15:8 and the patch level in bits 7:0 which is exactly what 714 * the REG_PHY_REVISION register layout is. 715 */ 716 if (priv->int_phy_mask & BIT(port)) 717 return priv->hw_params.gphy_rev; 718 else 719 return PHY_BRCM_AUTO_PWRDWN_ENABLE | 720 PHY_BRCM_DIS_TXCRXC_NOENRGY | 721 PHY_BRCM_IDDQ_SUSPEND; 722} 723 724static void bcm_sf2_sw_get_caps(struct dsa_switch *ds, int port, 725 struct phylink_config *config) 726{ 727 unsigned long *interfaces = config->supported_interfaces; 728 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 729 730 if (priv->int_phy_mask & BIT(port)) { 731 __set_bit(PHY_INTERFACE_MODE_INTERNAL, interfaces); 732 } else if (priv->moca_port == port) { 733 __set_bit(PHY_INTERFACE_MODE_MOCA, interfaces); 734 } else { 735 __set_bit(PHY_INTERFACE_MODE_MII, interfaces); 736 __set_bit(PHY_INTERFACE_MODE_REVMII, interfaces); 737 __set_bit(PHY_INTERFACE_MODE_GMII, interfaces); 738 phy_interface_set_rgmii(interfaces); 739 } 740 741 config->mac_capabilities = MAC_ASYM_PAUSE | MAC_SYM_PAUSE | 742 MAC_10 | MAC_100 | MAC_1000; 743} 744 745static void bcm_sf2_sw_mac_config(struct dsa_switch *ds, int port, 746 unsigned int mode, 747 const struct phylink_link_state *state) 748{ 749 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 750 u32 id_mode_dis = 0, port_mode; 751 u32 reg_rgmii_ctrl; 752 u32 reg; 753 754 if (port == core_readl(priv, CORE_IMP0_PRT_ID)) 755 return; 756 757 switch (state->interface) { 758 case PHY_INTERFACE_MODE_RGMII: 759 id_mode_dis = 1; 760 fallthrough; 761 case PHY_INTERFACE_MODE_RGMII_TXID: 762 port_mode = EXT_GPHY; 763 break; 764 case PHY_INTERFACE_MODE_MII: 765 port_mode = EXT_EPHY; 766 break; 767 case PHY_INTERFACE_MODE_REVMII: 768 port_mode = EXT_REVMII; 769 break; 770 default: 771 /* Nothing required for all other PHYs: internal and MoCA */ 772 return; 773 } 774 775 reg_rgmii_ctrl = bcm_sf2_reg_rgmii_cntrl(priv, port); 776 777 /* Clear id_mode_dis bit, and the existing port mode, let 778 * RGMII_MODE_EN bet set by mac_link_{up,down} 779 */ 780 reg = reg_readl(priv, reg_rgmii_ctrl); 781 reg &= ~ID_MODE_DIS; 782 reg &= ~(PORT_MODE_MASK << PORT_MODE_SHIFT); 783 784 reg |= port_mode; 785 if (id_mode_dis) 786 reg |= ID_MODE_DIS; 787 788 reg_writel(priv, reg, reg_rgmii_ctrl); 789} 790 791static void bcm_sf2_sw_mac_link_set(struct dsa_switch *ds, int port, 792 phy_interface_t interface, bool link) 793{ 794 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 795 u32 reg_rgmii_ctrl; 796 u32 reg; 797 798 if (!phy_interface_mode_is_rgmii(interface) && 799 interface != PHY_INTERFACE_MODE_MII && 800 interface != PHY_INTERFACE_MODE_REVMII) 801 return; 802 803 reg_rgmii_ctrl = bcm_sf2_reg_rgmii_cntrl(priv, port); 804 805 /* If the link is down, just disable the interface to conserve power */ 806 reg = reg_readl(priv, reg_rgmii_ctrl); 807 if (link) 808 reg |= RGMII_MODE_EN; 809 else 810 reg &= ~RGMII_MODE_EN; 811 reg_writel(priv, reg, reg_rgmii_ctrl); 812} 813 814static void bcm_sf2_sw_mac_link_down(struct dsa_switch *ds, int port, 815 unsigned int mode, 816 phy_interface_t interface) 817{ 818 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 819 u32 reg, offset; 820 821 if (priv->wol_ports_mask & BIT(port)) 822 return; 823 824 offset = bcm_sf2_port_override_offset(priv, port); 825 reg = core_readl(priv, offset); 826 reg &= ~LINK_STS; 827 core_writel(priv, reg, offset); 828 829 bcm_sf2_sw_mac_link_set(ds, port, interface, false); 830} 831 832static void bcm_sf2_sw_mac_link_up(struct dsa_switch *ds, int port, 833 unsigned int mode, 834 phy_interface_t interface, 835 struct phy_device *phydev, 836 int speed, int duplex, 837 bool tx_pause, bool rx_pause) 838{ 839 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 840 struct ethtool_eee *p = &priv->dev->ports[port].eee; 841 u32 reg_rgmii_ctrl = 0; 842 u32 reg, offset; 843 844 bcm_sf2_sw_mac_link_set(ds, port, interface, true); 845 846 offset = bcm_sf2_port_override_offset(priv, port); 847 848 if (phy_interface_mode_is_rgmii(interface) || 849 interface == PHY_INTERFACE_MODE_MII || 850 interface == PHY_INTERFACE_MODE_REVMII) { 851 reg_rgmii_ctrl = bcm_sf2_reg_rgmii_cntrl(priv, port); 852 reg = reg_readl(priv, reg_rgmii_ctrl); 853 reg &= ~(RX_PAUSE_EN | TX_PAUSE_EN); 854 855 if (tx_pause) 856 reg |= TX_PAUSE_EN; 857 if (rx_pause) 858 reg |= RX_PAUSE_EN; 859 860 reg_writel(priv, reg, reg_rgmii_ctrl); 861 } 862 863 reg = LINK_STS; 864 if (port == 8) { 865 if (priv->type == BCM4908_DEVICE_ID) 866 reg |= GMII_SPEED_UP_2G; 867 reg |= MII_SW_OR; 868 } else { 869 reg |= SW_OVERRIDE; 870 } 871 872 switch (speed) { 873 case SPEED_1000: 874 reg |= SPDSTS_1000 << SPEED_SHIFT; 875 break; 876 case SPEED_100: 877 reg |= SPDSTS_100 << SPEED_SHIFT; 878 break; 879 } 880 881 if (duplex == DUPLEX_FULL) 882 reg |= DUPLX_MODE; 883 884 if (tx_pause) 885 reg |= TXFLOW_CNTL; 886 if (rx_pause) 887 reg |= RXFLOW_CNTL; 888 889 core_writel(priv, reg, offset); 890 891 if (mode == MLO_AN_PHY && phydev) 892 p->eee_enabled = b53_eee_init(ds, port, phydev); 893} 894 895static void bcm_sf2_sw_fixed_state(struct dsa_switch *ds, int port, 896 struct phylink_link_state *status) 897{ 898 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 899 900 status->link = false; 901 902 /* MoCA port is special as we do not get link status from CORE_LNKSTS, 903 * which means that we need to force the link at the port override 904 * level to get the data to flow. We do use what the interrupt handler 905 * did determine before. 906 * 907 * For the other ports, we just force the link status, since this is 908 * a fixed PHY device. 909 */ 910 if (port == priv->moca_port) { 911 status->link = priv->port_sts[port].link; 912 /* For MoCA interfaces, also force a link down notification 913 * since some version of the user-space daemon (mocad) use 914 * cmd->autoneg to force the link, which messes up the PHY 915 * state machine and make it go in PHY_FORCING state instead. 916 */ 917 if (!status->link) 918 netif_carrier_off(dsa_to_port(ds, port)->slave); 919 status->duplex = DUPLEX_FULL; 920 } else { 921 status->link = true; 922 } 923} 924 925static void bcm_sf2_enable_acb(struct dsa_switch *ds) 926{ 927 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 928 u32 reg; 929 930 /* Enable ACB globally */ 931 reg = acb_readl(priv, ACB_CONTROL); 932 reg |= (ACB_FLUSH_MASK << ACB_FLUSH_SHIFT); 933 acb_writel(priv, reg, ACB_CONTROL); 934 reg &= ~(ACB_FLUSH_MASK << ACB_FLUSH_SHIFT); 935 reg |= ACB_EN | ACB_ALGORITHM; 936 acb_writel(priv, reg, ACB_CONTROL); 937} 938 939static int bcm_sf2_sw_suspend(struct dsa_switch *ds) 940{ 941 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 942 unsigned int port; 943 944 bcm_sf2_intr_disable(priv); 945 946 /* Disable all ports physically present including the IMP 947 * port, the other ones have already been disabled during 948 * bcm_sf2_sw_setup 949 */ 950 for (port = 0; port < ds->num_ports; port++) { 951 if (dsa_is_user_port(ds, port) || dsa_is_cpu_port(ds, port)) 952 bcm_sf2_port_disable(ds, port); 953 } 954 955 if (!priv->wol_ports_mask) 956 clk_disable_unprepare(priv->clk); 957 958 return 0; 959} 960 961static int bcm_sf2_sw_resume(struct dsa_switch *ds) 962{ 963 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 964 int ret; 965 966 if (!priv->wol_ports_mask) 967 clk_prepare_enable(priv->clk); 968 969 ret = bcm_sf2_sw_rst(priv); 970 if (ret) { 971 pr_err("%s: failed to software reset switch\n", __func__); 972 return ret; 973 } 974 975 bcm_sf2_crossbar_setup(priv); 976 977 ret = bcm_sf2_cfp_resume(ds); 978 if (ret) 979 return ret; 980 981 if (priv->hw_params.num_gphy == 1) 982 bcm_sf2_gphy_enable_set(ds, true); 983 984 ds->ops->setup(ds); 985 986 return 0; 987} 988 989static void bcm_sf2_sw_get_wol(struct dsa_switch *ds, int port, 990 struct ethtool_wolinfo *wol) 991{ 992 struct net_device *p = dsa_port_to_master(dsa_to_port(ds, port)); 993 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 994 struct ethtool_wolinfo pwol = { }; 995 996 /* Get the parent device WoL settings */ 997 if (p->ethtool_ops->get_wol) 998 p->ethtool_ops->get_wol(p, &pwol); 999 1000 /* Advertise the parent device supported settings */ 1001 wol->supported = pwol.supported; 1002 memset(&wol->sopass, 0, sizeof(wol->sopass)); 1003 1004 if (pwol.wolopts & WAKE_MAGICSECURE) 1005 memcpy(&wol->sopass, pwol.sopass, sizeof(wol->sopass)); 1006 1007 if (priv->wol_ports_mask & (1 << port)) 1008 wol->wolopts = pwol.wolopts; 1009 else 1010 wol->wolopts = 0; 1011} 1012 1013static int bcm_sf2_sw_set_wol(struct dsa_switch *ds, int port, 1014 struct ethtool_wolinfo *wol) 1015{ 1016 struct net_device *p = dsa_port_to_master(dsa_to_port(ds, port)); 1017 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 1018 s8 cpu_port = dsa_to_port(ds, port)->cpu_dp->index; 1019 struct ethtool_wolinfo pwol = { }; 1020 1021 if (p->ethtool_ops->get_wol) 1022 p->ethtool_ops->get_wol(p, &pwol); 1023 if (wol->wolopts & ~pwol.supported) 1024 return -EINVAL; 1025 1026 if (wol->wolopts) 1027 priv->wol_ports_mask |= (1 << port); 1028 else 1029 priv->wol_ports_mask &= ~(1 << port); 1030 1031 /* If we have at least one port enabled, make sure the CPU port 1032 * is also enabled. If the CPU port is the last one enabled, we disable 1033 * it since this configuration does not make sense. 1034 */ 1035 if (priv->wol_ports_mask && priv->wol_ports_mask != (1 << cpu_port)) 1036 priv->wol_ports_mask |= (1 << cpu_port); 1037 else 1038 priv->wol_ports_mask &= ~(1 << cpu_port); 1039 1040 return p->ethtool_ops->set_wol(p, wol); 1041} 1042 1043static int bcm_sf2_sw_setup(struct dsa_switch *ds) 1044{ 1045 struct bcm_sf2_priv *priv = bcm_sf2_to_priv(ds); 1046 unsigned int port; 1047 1048 /* Enable all valid ports and disable those unused */ 1049 for (port = 0; port < priv->hw_params.num_ports; port++) { 1050 /* IMP port receives special treatment */ 1051 if (dsa_is_user_port(ds, port)) 1052 bcm_sf2_port_setup(ds, port, NULL); 1053 else if (dsa_is_cpu_port(ds, port)) 1054 bcm_sf2_imp_setup(ds, port); 1055 else 1056 bcm_sf2_port_disable(ds, port); 1057 } 1058 1059 b53_configure_vlan(ds); 1060 bcm_sf2_enable_acb(ds); 1061 1062 return b53_setup_devlink_resources(ds); 1063} 1064 1065static void bcm_sf2_sw_teardown(struct dsa_switch *ds) 1066{ 1067 dsa_devlink_resources_unregister(ds); 1068} 1069 1070/* The SWITCH_CORE register space is managed by b53 but operates on a page + 1071 * register basis so we need to translate that into an address that the 1072 * bus-glue understands. 1073 */ 1074#define SF2_PAGE_REG_MKADDR(page, reg) ((page) << 10 | (reg) << 2) 1075 1076static int bcm_sf2_core_read8(struct b53_device *dev, u8 page, u8 reg, 1077 u8 *val) 1078{ 1079 struct bcm_sf2_priv *priv = dev->priv; 1080 1081 *val = core_readl(priv, SF2_PAGE_REG_MKADDR(page, reg)); 1082 1083 return 0; 1084} 1085 1086static int bcm_sf2_core_read16(struct b53_device *dev, u8 page, u8 reg, 1087 u16 *val) 1088{ 1089 struct bcm_sf2_priv *priv = dev->priv; 1090 1091 *val = core_readl(priv, SF2_PAGE_REG_MKADDR(page, reg)); 1092 1093 return 0; 1094} 1095 1096static int bcm_sf2_core_read32(struct b53_device *dev, u8 page, u8 reg, 1097 u32 *val) 1098{ 1099 struct bcm_sf2_priv *priv = dev->priv; 1100 1101 *val = core_readl(priv, SF2_PAGE_REG_MKADDR(page, reg)); 1102 1103 return 0; 1104} 1105 1106static int bcm_sf2_core_read64(struct b53_device *dev, u8 page, u8 reg, 1107 u64 *val) 1108{ 1109 struct bcm_sf2_priv *priv = dev->priv; 1110 1111 *val = core_readq(priv, SF2_PAGE_REG_MKADDR(page, reg)); 1112 1113 return 0; 1114} 1115 1116static int bcm_sf2_core_write8(struct b53_device *dev, u8 page, u8 reg, 1117 u8 value) 1118{ 1119 struct bcm_sf2_priv *priv = dev->priv; 1120 1121 core_writel(priv, value, SF2_PAGE_REG_MKADDR(page, reg)); 1122 1123 return 0; 1124} 1125 1126static int bcm_sf2_core_write16(struct b53_device *dev, u8 page, u8 reg, 1127 u16 value) 1128{ 1129 struct bcm_sf2_priv *priv = dev->priv; 1130 1131 core_writel(priv, value, SF2_PAGE_REG_MKADDR(page, reg)); 1132 1133 return 0; 1134} 1135 1136static int bcm_sf2_core_write32(struct b53_device *dev, u8 page, u8 reg, 1137 u32 value) 1138{ 1139 struct bcm_sf2_priv *priv = dev->priv; 1140 1141 core_writel(priv, value, SF2_PAGE_REG_MKADDR(page, reg)); 1142 1143 return 0; 1144} 1145 1146static int bcm_sf2_core_write64(struct b53_device *dev, u8 page, u8 reg, 1147 u64 value) 1148{ 1149 struct bcm_sf2_priv *priv = dev->priv; 1150 1151 core_writeq(priv, value, SF2_PAGE_REG_MKADDR(page, reg)); 1152 1153 return 0; 1154} 1155 1156static const struct b53_io_ops bcm_sf2_io_ops = { 1157 .read8 = bcm_sf2_core_read8, 1158 .read16 = bcm_sf2_core_read16, 1159 .read32 = bcm_sf2_core_read32, 1160 .read48 = bcm_sf2_core_read64, 1161 .read64 = bcm_sf2_core_read64, 1162 .write8 = bcm_sf2_core_write8, 1163 .write16 = bcm_sf2_core_write16, 1164 .write32 = bcm_sf2_core_write32, 1165 .write48 = bcm_sf2_core_write64, 1166 .write64 = bcm_sf2_core_write64, 1167}; 1168 1169static void bcm_sf2_sw_get_strings(struct dsa_switch *ds, int port, 1170 u32 stringset, uint8_t *data) 1171{ 1172 int cnt = b53_get_sset_count(ds, port, stringset); 1173 1174 b53_get_strings(ds, port, stringset, data); 1175 bcm_sf2_cfp_get_strings(ds, port, stringset, 1176 data + cnt * ETH_GSTRING_LEN); 1177} 1178 1179static void bcm_sf2_sw_get_ethtool_stats(struct dsa_switch *ds, int port, 1180 uint64_t *data) 1181{ 1182 int cnt = b53_get_sset_count(ds, port, ETH_SS_STATS); 1183 1184 b53_get_ethtool_stats(ds, port, data); 1185 bcm_sf2_cfp_get_ethtool_stats(ds, port, data + cnt); 1186} 1187 1188static int bcm_sf2_sw_get_sset_count(struct dsa_switch *ds, int port, 1189 int sset) 1190{ 1191 int cnt = b53_get_sset_count(ds, port, sset); 1192 1193 if (cnt < 0) 1194 return cnt; 1195 1196 cnt += bcm_sf2_cfp_get_sset_count(ds, port, sset); 1197 1198 return cnt; 1199} 1200 1201static const struct dsa_switch_ops bcm_sf2_ops = { 1202 .get_tag_protocol = b53_get_tag_protocol, 1203 .setup = bcm_sf2_sw_setup, 1204 .teardown = bcm_sf2_sw_teardown, 1205 .get_strings = bcm_sf2_sw_get_strings, 1206 .get_ethtool_stats = bcm_sf2_sw_get_ethtool_stats, 1207 .get_sset_count = bcm_sf2_sw_get_sset_count, 1208 .get_ethtool_phy_stats = b53_get_ethtool_phy_stats, 1209 .get_phy_flags = bcm_sf2_sw_get_phy_flags, 1210 .phylink_get_caps = bcm_sf2_sw_get_caps, 1211 .phylink_mac_config = bcm_sf2_sw_mac_config, 1212 .phylink_mac_link_down = bcm_sf2_sw_mac_link_down, 1213 .phylink_mac_link_up = bcm_sf2_sw_mac_link_up, 1214 .phylink_fixed_state = bcm_sf2_sw_fixed_state, 1215 .suspend = bcm_sf2_sw_suspend, 1216 .resume = bcm_sf2_sw_resume, 1217 .get_wol = bcm_sf2_sw_get_wol, 1218 .set_wol = bcm_sf2_sw_set_wol, 1219 .port_enable = bcm_sf2_port_setup, 1220 .port_disable = bcm_sf2_port_disable, 1221 .get_mac_eee = b53_get_mac_eee, 1222 .set_mac_eee = b53_set_mac_eee, 1223 .port_bridge_join = b53_br_join, 1224 .port_bridge_leave = b53_br_leave, 1225 .port_pre_bridge_flags = b53_br_flags_pre, 1226 .port_bridge_flags = b53_br_flags, 1227 .port_stp_state_set = b53_br_set_stp_state, 1228 .port_fast_age = b53_br_fast_age, 1229 .port_vlan_filtering = b53_vlan_filtering, 1230 .port_vlan_add = b53_vlan_add, 1231 .port_vlan_del = b53_vlan_del, 1232 .port_fdb_dump = b53_fdb_dump, 1233 .port_fdb_add = b53_fdb_add, 1234 .port_fdb_del = b53_fdb_del, 1235 .get_rxnfc = bcm_sf2_get_rxnfc, 1236 .set_rxnfc = bcm_sf2_set_rxnfc, 1237 .port_mirror_add = b53_mirror_add, 1238 .port_mirror_del = b53_mirror_del, 1239 .port_mdb_add = b53_mdb_add, 1240 .port_mdb_del = b53_mdb_del, 1241}; 1242 1243struct bcm_sf2_of_data { 1244 u32 type; 1245 const u16 *reg_offsets; 1246 unsigned int core_reg_align; 1247 unsigned int num_cfp_rules; 1248 unsigned int num_crossbar_int_ports; 1249}; 1250 1251static const u16 bcm_sf2_4908_reg_offsets[] = { 1252 [REG_SWITCH_CNTRL] = 0x00, 1253 [REG_SWITCH_STATUS] = 0x04, 1254 [REG_DIR_DATA_WRITE] = 0x08, 1255 [REG_DIR_DATA_READ] = 0x0c, 1256 [REG_SWITCH_REVISION] = 0x10, 1257 [REG_PHY_REVISION] = 0x14, 1258 [REG_SPHY_CNTRL] = 0x24, 1259 [REG_CROSSBAR] = 0xc8, 1260 [REG_RGMII_11_CNTRL] = 0x014c, 1261 [REG_LED_0_CNTRL] = 0x40, 1262 [REG_LED_1_CNTRL] = 0x4c, 1263 [REG_LED_2_CNTRL] = 0x58, 1264 [REG_LED_3_CNTRL] = 0x64, 1265 [REG_LED_4_CNTRL] = 0x88, 1266 [REG_LED_5_CNTRL] = 0xa0, 1267 [REG_LED_AGGREGATE_CTRL] = 0xb8, 1268 1269}; 1270 1271static const struct bcm_sf2_of_data bcm_sf2_4908_data = { 1272 .type = BCM4908_DEVICE_ID, 1273 .core_reg_align = 0, 1274 .reg_offsets = bcm_sf2_4908_reg_offsets, 1275 .num_cfp_rules = 256, 1276 .num_crossbar_int_ports = 2, 1277}; 1278 1279/* Register offsets for the SWITCH_REG_* block */ 1280static const u16 bcm_sf2_7445_reg_offsets[] = { 1281 [REG_SWITCH_CNTRL] = 0x00, 1282 [REG_SWITCH_STATUS] = 0x04, 1283 [REG_DIR_DATA_WRITE] = 0x08, 1284 [REG_DIR_DATA_READ] = 0x0C, 1285 [REG_SWITCH_REVISION] = 0x18, 1286 [REG_PHY_REVISION] = 0x1C, 1287 [REG_SPHY_CNTRL] = 0x2C, 1288 [REG_RGMII_0_CNTRL] = 0x34, 1289 [REG_RGMII_1_CNTRL] = 0x40, 1290 [REG_RGMII_2_CNTRL] = 0x4c, 1291 [REG_LED_0_CNTRL] = 0x90, 1292 [REG_LED_1_CNTRL] = 0x94, 1293 [REG_LED_2_CNTRL] = 0x98, 1294}; 1295 1296static const struct bcm_sf2_of_data bcm_sf2_7445_data = { 1297 .type = BCM7445_DEVICE_ID, 1298 .core_reg_align = 0, 1299 .reg_offsets = bcm_sf2_7445_reg_offsets, 1300 .num_cfp_rules = 256, 1301}; 1302 1303static const u16 bcm_sf2_7278_reg_offsets[] = { 1304 [REG_SWITCH_CNTRL] = 0x00, 1305 [REG_SWITCH_STATUS] = 0x04, 1306 [REG_DIR_DATA_WRITE] = 0x08, 1307 [REG_DIR_DATA_READ] = 0x0c, 1308 [REG_SWITCH_REVISION] = 0x10, 1309 [REG_PHY_REVISION] = 0x14, 1310 [REG_SPHY_CNTRL] = 0x24, 1311 [REG_RGMII_0_CNTRL] = 0xe0, 1312 [REG_RGMII_1_CNTRL] = 0xec, 1313 [REG_RGMII_2_CNTRL] = 0xf8, 1314 [REG_LED_0_CNTRL] = 0x40, 1315 [REG_LED_1_CNTRL] = 0x4c, 1316 [REG_LED_2_CNTRL] = 0x58, 1317}; 1318 1319static const struct bcm_sf2_of_data bcm_sf2_7278_data = { 1320 .type = BCM7278_DEVICE_ID, 1321 .core_reg_align = 1, 1322 .reg_offsets = bcm_sf2_7278_reg_offsets, 1323 .num_cfp_rules = 128, 1324}; 1325 1326static const struct of_device_id bcm_sf2_of_match[] = { 1327 { .compatible = "brcm,bcm4908-switch", 1328 .data = &bcm_sf2_4908_data 1329 }, 1330 { .compatible = "brcm,bcm7445-switch-v4.0", 1331 .data = &bcm_sf2_7445_data 1332 }, 1333 { .compatible = "brcm,bcm7278-switch-v4.0", 1334 .data = &bcm_sf2_7278_data 1335 }, 1336 { .compatible = "brcm,bcm7278-switch-v4.8", 1337 .data = &bcm_sf2_7278_data 1338 }, 1339 { /* sentinel */ }, 1340}; 1341MODULE_DEVICE_TABLE(of, bcm_sf2_of_match); 1342 1343static int bcm_sf2_sw_probe(struct platform_device *pdev) 1344{ 1345 const char *reg_names[BCM_SF2_REGS_NUM] = BCM_SF2_REGS_NAME; 1346 struct device_node *dn = pdev->dev.of_node; 1347 const struct of_device_id *of_id = NULL; 1348 const struct bcm_sf2_of_data *data; 1349 struct b53_platform_data *pdata; 1350 struct dsa_switch_ops *ops; 1351 struct device_node *ports; 1352 struct bcm_sf2_priv *priv; 1353 struct b53_device *dev; 1354 struct dsa_switch *ds; 1355 void __iomem **base; 1356 unsigned int i; 1357 u32 reg, rev; 1358 int ret; 1359 1360 priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); 1361 if (!priv) 1362 return -ENOMEM; 1363 1364 ops = devm_kzalloc(&pdev->dev, sizeof(*ops), GFP_KERNEL); 1365 if (!ops) 1366 return -ENOMEM; 1367 1368 dev = b53_switch_alloc(&pdev->dev, &bcm_sf2_io_ops, priv); 1369 if (!dev) 1370 return -ENOMEM; 1371 1372 pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL); 1373 if (!pdata) 1374 return -ENOMEM; 1375 1376 of_id = of_match_node(bcm_sf2_of_match, dn); 1377 if (!of_id || !of_id->data) 1378 return -EINVAL; 1379 1380 data = of_id->data; 1381 1382 /* Set SWITCH_REG register offsets and SWITCH_CORE align factor */ 1383 priv->type = data->type; 1384 priv->reg_offsets = data->reg_offsets; 1385 priv->core_reg_align = data->core_reg_align; 1386 priv->num_cfp_rules = data->num_cfp_rules; 1387 priv->num_crossbar_int_ports = data->num_crossbar_int_ports; 1388 1389 priv->rcdev = devm_reset_control_get_optional_exclusive(&pdev->dev, 1390 "switch"); 1391 if (IS_ERR(priv->rcdev)) 1392 return PTR_ERR(priv->rcdev); 1393 1394 /* Auto-detection using standard registers will not work, so 1395 * provide an indication of what kind of device we are for 1396 * b53_common to work with 1397 */ 1398 pdata->chip_id = priv->type; 1399 dev->pdata = pdata; 1400 1401 priv->dev = dev; 1402 ds = dev->ds; 1403 ds->ops = &bcm_sf2_ops; 1404 1405 /* Advertise the 8 egress queues */ 1406 ds->num_tx_queues = SF2_NUM_EGRESS_QUEUES; 1407 1408 dev_set_drvdata(&pdev->dev, priv); 1409 1410 spin_lock_init(&priv->indir_lock); 1411 mutex_init(&priv->cfp.lock); 1412 INIT_LIST_HEAD(&priv->cfp.rules_list); 1413 1414 /* CFP rule #0 cannot be used for specific classifications, flag it as 1415 * permanently used 1416 */ 1417 set_bit(0, priv->cfp.used); 1418 set_bit(0, priv->cfp.unique); 1419 1420 /* Balance of_node_put() done by of_find_node_by_name() */ 1421 of_node_get(dn); 1422 ports = of_find_node_by_name(dn, "ports"); 1423 if (ports) { 1424 bcm_sf2_identify_ports(priv, ports); 1425 of_node_put(ports); 1426 } 1427 1428 priv->irq0 = irq_of_parse_and_map(dn, 0); 1429 priv->irq1 = irq_of_parse_and_map(dn, 1); 1430 1431 base = &priv->core; 1432 for (i = 0; i < BCM_SF2_REGS_NUM; i++) { 1433 *base = devm_platform_ioremap_resource(pdev, i); 1434 if (IS_ERR(*base)) { 1435 pr_err("unable to find register: %s\n", reg_names[i]); 1436 return PTR_ERR(*base); 1437 } 1438 base++; 1439 } 1440 1441 priv->clk = devm_clk_get_optional(&pdev->dev, "sw_switch"); 1442 if (IS_ERR(priv->clk)) 1443 return PTR_ERR(priv->clk); 1444 1445 ret = clk_prepare_enable(priv->clk); 1446 if (ret) 1447 return ret; 1448 1449 priv->clk_mdiv = devm_clk_get_optional(&pdev->dev, "sw_switch_mdiv"); 1450 if (IS_ERR(priv->clk_mdiv)) { 1451 ret = PTR_ERR(priv->clk_mdiv); 1452 goto out_clk; 1453 } 1454 1455 ret = clk_prepare_enable(priv->clk_mdiv); 1456 if (ret) 1457 goto out_clk; 1458 1459 ret = bcm_sf2_sw_rst(priv); 1460 if (ret) { 1461 pr_err("unable to software reset switch: %d\n", ret); 1462 goto out_clk_mdiv; 1463 } 1464 1465 bcm_sf2_crossbar_setup(priv); 1466 1467 bcm_sf2_gphy_enable_set(priv->dev->ds, true); 1468 1469 ret = bcm_sf2_mdio_register(ds); 1470 if (ret) { 1471 pr_err("failed to register MDIO bus\n"); 1472 goto out_clk_mdiv; 1473 } 1474 1475 bcm_sf2_gphy_enable_set(priv->dev->ds, false); 1476 1477 ret = bcm_sf2_cfp_rst(priv); 1478 if (ret) { 1479 pr_err("failed to reset CFP\n"); 1480 goto out_mdio; 1481 } 1482 1483 /* Disable all interrupts and request them */ 1484 bcm_sf2_intr_disable(priv); 1485 1486 ret = devm_request_irq(&pdev->dev, priv->irq0, bcm_sf2_switch_0_isr, 0, 1487 "switch_0", ds); 1488 if (ret < 0) { 1489 pr_err("failed to request switch_0 IRQ\n"); 1490 goto out_mdio; 1491 } 1492 1493 ret = devm_request_irq(&pdev->dev, priv->irq1, bcm_sf2_switch_1_isr, 0, 1494 "switch_1", ds); 1495 if (ret < 0) { 1496 pr_err("failed to request switch_1 IRQ\n"); 1497 goto out_mdio; 1498 } 1499 1500 /* Reset the MIB counters */ 1501 reg = core_readl(priv, CORE_GMNCFGCFG); 1502 reg |= RST_MIB_CNT; 1503 core_writel(priv, reg, CORE_GMNCFGCFG); 1504 reg &= ~RST_MIB_CNT; 1505 core_writel(priv, reg, CORE_GMNCFGCFG); 1506 1507 /* Get the maximum number of ports for this switch */ 1508 priv->hw_params.num_ports = core_readl(priv, CORE_IMP0_PRT_ID) + 1; 1509 if (priv->hw_params.num_ports > DSA_MAX_PORTS) 1510 priv->hw_params.num_ports = DSA_MAX_PORTS; 1511 1512 /* Assume a single GPHY setup if we can't read that property */ 1513 if (of_property_read_u32(dn, "brcm,num-gphy", 1514 &priv->hw_params.num_gphy)) 1515 priv->hw_params.num_gphy = 1; 1516 1517 rev = reg_readl(priv, REG_SWITCH_REVISION); 1518 priv->hw_params.top_rev = (rev >> SWITCH_TOP_REV_SHIFT) & 1519 SWITCH_TOP_REV_MASK; 1520 priv->hw_params.core_rev = (rev & SF2_REV_MASK); 1521 1522 rev = reg_readl(priv, REG_PHY_REVISION); 1523 priv->hw_params.gphy_rev = rev & PHY_REVISION_MASK; 1524 1525 ret = b53_switch_register(dev); 1526 if (ret) 1527 goto out_mdio; 1528 1529 dev_info(&pdev->dev, 1530 "Starfighter 2 top: %x.%02x, core: %x.%02x, IRQs: %d, %d\n", 1531 priv->hw_params.top_rev >> 8, priv->hw_params.top_rev & 0xff, 1532 priv->hw_params.core_rev >> 8, priv->hw_params.core_rev & 0xff, 1533 priv->irq0, priv->irq1); 1534 1535 return 0; 1536 1537out_mdio: 1538 bcm_sf2_mdio_unregister(priv); 1539out_clk_mdiv: 1540 clk_disable_unprepare(priv->clk_mdiv); 1541out_clk: 1542 clk_disable_unprepare(priv->clk); 1543 return ret; 1544} 1545 1546static int bcm_sf2_sw_remove(struct platform_device *pdev) 1547{ 1548 struct bcm_sf2_priv *priv = platform_get_drvdata(pdev); 1549 1550 if (!priv) 1551 return 0; 1552 1553 priv->wol_ports_mask = 0; 1554 /* Disable interrupts */ 1555 bcm_sf2_intr_disable(priv); 1556 dsa_unregister_switch(priv->dev->ds); 1557 bcm_sf2_cfp_exit(priv->dev->ds); 1558 bcm_sf2_mdio_unregister(priv); 1559 clk_disable_unprepare(priv->clk_mdiv); 1560 clk_disable_unprepare(priv->clk); 1561 if (priv->type == BCM7278_DEVICE_ID) 1562 reset_control_assert(priv->rcdev); 1563 1564 return 0; 1565} 1566 1567static void bcm_sf2_sw_shutdown(struct platform_device *pdev) 1568{ 1569 struct bcm_sf2_priv *priv = platform_get_drvdata(pdev); 1570 1571 if (!priv) 1572 return; 1573 1574 /* For a kernel about to be kexec'd we want to keep the GPHY on for a 1575 * successful MDIO bus scan to occur. If we did turn off the GPHY 1576 * before (e.g: port_disable), this will also power it back on. 1577 * 1578 * Do not rely on kexec_in_progress, just power the PHY on. 1579 */ 1580 if (priv->hw_params.num_gphy == 1) 1581 bcm_sf2_gphy_enable_set(priv->dev->ds, true); 1582 1583 dsa_switch_shutdown(priv->dev->ds); 1584 1585 platform_set_drvdata(pdev, NULL); 1586} 1587 1588#ifdef CONFIG_PM_SLEEP 1589static int bcm_sf2_suspend(struct device *dev) 1590{ 1591 struct bcm_sf2_priv *priv = dev_get_drvdata(dev); 1592 1593 return dsa_switch_suspend(priv->dev->ds); 1594} 1595 1596static int bcm_sf2_resume(struct device *dev) 1597{ 1598 struct bcm_sf2_priv *priv = dev_get_drvdata(dev); 1599 1600 return dsa_switch_resume(priv->dev->ds); 1601} 1602#endif /* CONFIG_PM_SLEEP */ 1603 1604static SIMPLE_DEV_PM_OPS(bcm_sf2_pm_ops, 1605 bcm_sf2_suspend, bcm_sf2_resume); 1606 1607 1608static struct platform_driver bcm_sf2_driver = { 1609 .probe = bcm_sf2_sw_probe, 1610 .remove = bcm_sf2_sw_remove, 1611 .shutdown = bcm_sf2_sw_shutdown, 1612 .driver = { 1613 .name = "brcm-sf2", 1614 .of_match_table = bcm_sf2_of_match, 1615 .pm = &bcm_sf2_pm_ops, 1616 }, 1617}; 1618module_platform_driver(bcm_sf2_driver); 1619 1620MODULE_AUTHOR("Broadcom Corporation"); 1621MODULE_DESCRIPTION("Driver for Broadcom Starfighter 2 ethernet switch chip"); 1622MODULE_LICENSE("GPL"); 1623MODULE_ALIAS("platform:brcm-sf2"); 1624