1// SPDX-License-Identifier: GPL-2.0 2/* 3 * Freescale eSDHC i.MX controller driver for the platform bus. 4 * 5 * derived from the OF-version. 6 * 7 * Copyright (c) 2010 Pengutronix e.K. 8 * Author: Wolfram Sang <kernel@pengutronix.de> 9 */ 10 11#include <linux/bitfield.h> 12#include <linux/io.h> 13#include <linux/iopoll.h> 14#include <linux/delay.h> 15#include <linux/err.h> 16#include <linux/clk.h> 17#include <linux/module.h> 18#include <linux/slab.h> 19#include <linux/pm_qos.h> 20#include <linux/mmc/host.h> 21#include <linux/mmc/mmc.h> 22#include <linux/mmc/sdio.h> 23#include <linux/mmc/slot-gpio.h> 24#include <linux/of.h> 25#include <linux/platform_device.h> 26#include <linux/pinctrl/consumer.h> 27#include <linux/pm_runtime.h> 28#include "sdhci-cqhci.h" 29#include "sdhci-pltfm.h" 30#include "sdhci-esdhc.h" 31#include "cqhci.h" 32 33#define ESDHC_SYS_CTRL_DTOCV_MASK 0x0f 34#define ESDHC_CTRL_D3CD 0x08 35#define ESDHC_BURST_LEN_EN_INCR (1 << 27) 36/* VENDOR SPEC register */ 37#define ESDHC_VENDOR_SPEC 0xc0 38#define ESDHC_VENDOR_SPEC_SDIO_QUIRK (1 << 1) 39#define ESDHC_VENDOR_SPEC_VSELECT (1 << 1) 40#define ESDHC_VENDOR_SPEC_FRC_SDCLK_ON (1 << 8) 41#define ESDHC_DEBUG_SEL_AND_STATUS_REG 0xc2 42#define ESDHC_DEBUG_SEL_REG 0xc3 43#define ESDHC_DEBUG_SEL_MASK 0xf 44#define ESDHC_DEBUG_SEL_CMD_STATE 1 45#define ESDHC_DEBUG_SEL_DATA_STATE 2 46#define ESDHC_DEBUG_SEL_TRANS_STATE 3 47#define ESDHC_DEBUG_SEL_DMA_STATE 4 48#define ESDHC_DEBUG_SEL_ADMA_STATE 5 49#define ESDHC_DEBUG_SEL_FIFO_STATE 6 50#define ESDHC_DEBUG_SEL_ASYNC_FIFO_STATE 7 51#define ESDHC_WTMK_LVL 0x44 52#define ESDHC_WTMK_DEFAULT_VAL 0x10401040 53#define ESDHC_WTMK_LVL_RD_WML_MASK 0x000000FF 54#define ESDHC_WTMK_LVL_RD_WML_SHIFT 0 55#define ESDHC_WTMK_LVL_WR_WML_MASK 0x00FF0000 56#define ESDHC_WTMK_LVL_WR_WML_SHIFT 16 57#define ESDHC_WTMK_LVL_WML_VAL_DEF 64 58#define ESDHC_WTMK_LVL_WML_VAL_MAX 128 59#define ESDHC_MIX_CTRL 0x48 60#define ESDHC_MIX_CTRL_DDREN (1 << 3) 61#define ESDHC_MIX_CTRL_AC23EN (1 << 7) 62#define ESDHC_MIX_CTRL_EXE_TUNE (1 << 22) 63#define ESDHC_MIX_CTRL_SMPCLK_SEL (1 << 23) 64#define ESDHC_MIX_CTRL_AUTO_TUNE_EN (1 << 24) 65#define ESDHC_MIX_CTRL_FBCLK_SEL (1 << 25) 66#define ESDHC_MIX_CTRL_HS400_EN (1 << 26) 67#define ESDHC_MIX_CTRL_HS400_ES_EN (1 << 27) 68/* Bits 3 and 6 are not SDHCI standard definitions */ 69#define ESDHC_MIX_CTRL_SDHCI_MASK 0xb7 70/* Tuning bits */ 71#define ESDHC_MIX_CTRL_TUNING_MASK 0x03c00000 72 73/* dll control register */ 74#define ESDHC_DLL_CTRL 0x60 75#define ESDHC_DLL_OVERRIDE_VAL_SHIFT 9 76#define ESDHC_DLL_OVERRIDE_EN_SHIFT 8 77 78/* tune control register */ 79#define ESDHC_TUNE_CTRL_STATUS 0x68 80#define ESDHC_TUNE_CTRL_STEP 1 81#define ESDHC_TUNE_CTRL_MIN 0 82#define ESDHC_TUNE_CTRL_MAX ((1 << 7) - 1) 83 84/* strobe dll register */ 85#define ESDHC_STROBE_DLL_CTRL 0x70 86#define ESDHC_STROBE_DLL_CTRL_ENABLE (1 << 0) 87#define ESDHC_STROBE_DLL_CTRL_RESET (1 << 1) 88#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT 0x7 89#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT 3 90#define ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT (4 << 20) 91 92#define ESDHC_STROBE_DLL_STATUS 0x74 93#define ESDHC_STROBE_DLL_STS_REF_LOCK (1 << 1) 94#define ESDHC_STROBE_DLL_STS_SLV_LOCK 0x1 95 96#define ESDHC_VEND_SPEC2 0xc8 97#define ESDHC_VEND_SPEC2_EN_BUSY_IRQ (1 << 8) 98#define ESDHC_VEND_SPEC2_AUTO_TUNE_8BIT_EN (1 << 4) 99#define ESDHC_VEND_SPEC2_AUTO_TUNE_4BIT_EN (0 << 4) 100#define ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN (2 << 4) 101#define ESDHC_VEND_SPEC2_AUTO_TUNE_CMD_EN (1 << 6) 102#define ESDHC_VEND_SPEC2_AUTO_TUNE_MODE_MASK (7 << 4) 103 104#define ESDHC_TUNING_CTRL 0xcc 105#define ESDHC_STD_TUNING_EN (1 << 24) 106/* NOTE: the minimum valid tuning start tap for mx6sl is 1 */ 107#define ESDHC_TUNING_START_TAP_DEFAULT 0x1 108#define ESDHC_TUNING_START_TAP_MASK 0x7f 109#define ESDHC_TUNING_CMD_CRC_CHECK_DISABLE (1 << 7) 110#define ESDHC_TUNING_STEP_DEFAULT 0x1 111#define ESDHC_TUNING_STEP_MASK 0x00070000 112#define ESDHC_TUNING_STEP_SHIFT 16 113 114/* pinctrl state */ 115#define ESDHC_PINCTRL_STATE_100MHZ "state_100mhz" 116#define ESDHC_PINCTRL_STATE_200MHZ "state_200mhz" 117 118/* 119 * Our interpretation of the SDHCI_HOST_CONTROL register 120 */ 121#define ESDHC_CTRL_4BITBUS (0x1 << 1) 122#define ESDHC_CTRL_8BITBUS (0x2 << 1) 123#define ESDHC_CTRL_BUSWIDTH_MASK (0x3 << 1) 124#define USDHC_GET_BUSWIDTH(c) (c & ESDHC_CTRL_BUSWIDTH_MASK) 125 126/* 127 * There is an INT DMA ERR mismatch between eSDHC and STD SDHC SPEC: 128 * Bit25 is used in STD SPEC, and is reserved in fsl eSDHC design, 129 * but bit28 is used as the INT DMA ERR in fsl eSDHC design. 130 * Define this macro DMA error INT for fsl eSDHC 131 */ 132#define ESDHC_INT_VENDOR_SPEC_DMA_ERR (1 << 28) 133 134/* the address offset of CQHCI */ 135#define ESDHC_CQHCI_ADDR_OFFSET 0x100 136 137/* 138 * The CMDTYPE of the CMD register (offset 0xE) should be set to 139 * "11" when the STOP CMD12 is issued on imx53 to abort one 140 * open ended multi-blk IO. Otherwise the TC INT wouldn't 141 * be generated. 142 * In exact block transfer, the controller doesn't complete the 143 * operations automatically as required at the end of the 144 * transfer and remains on hold if the abort command is not sent. 145 * As a result, the TC flag is not asserted and SW received timeout 146 * exception. Bit1 of Vendor Spec register is used to fix it. 147 */ 148#define ESDHC_FLAG_MULTIBLK_NO_INT BIT(1) 149/* 150 * The flag tells that the ESDHC controller is an USDHC block that is 151 * integrated on the i.MX6 series. 152 */ 153#define ESDHC_FLAG_USDHC BIT(3) 154/* The IP supports manual tuning process */ 155#define ESDHC_FLAG_MAN_TUNING BIT(4) 156/* The IP supports standard tuning process */ 157#define ESDHC_FLAG_STD_TUNING BIT(5) 158/* The IP has SDHCI_CAPABILITIES_1 register */ 159#define ESDHC_FLAG_HAVE_CAP1 BIT(6) 160/* 161 * The IP has erratum ERR004536 162 * uSDHC: ADMA Length Mismatch Error occurs if the AHB read access is slow, 163 * when reading data from the card 164 * This flag is also set for i.MX25 and i.MX35 in order to get 165 * SDHCI_QUIRK_BROKEN_ADMA, but for different reasons (ADMA capability bits). 166 */ 167#define ESDHC_FLAG_ERR004536 BIT(7) 168/* The IP supports HS200 mode */ 169#define ESDHC_FLAG_HS200 BIT(8) 170/* The IP supports HS400 mode */ 171#define ESDHC_FLAG_HS400 BIT(9) 172/* 173 * The IP has errata ERR010450 174 * uSDHC: At 1.8V due to the I/O timing limit, for SDR mode, SD card 175 * clock can't exceed 150MHz, for DDR mode, SD card clock can't exceed 45MHz. 176 */ 177#define ESDHC_FLAG_ERR010450 BIT(10) 178/* The IP supports HS400ES mode */ 179#define ESDHC_FLAG_HS400_ES BIT(11) 180/* The IP has Host Controller Interface for Command Queuing */ 181#define ESDHC_FLAG_CQHCI BIT(12) 182/* need request pmqos during low power */ 183#define ESDHC_FLAG_PMQOS BIT(13) 184/* The IP state got lost in low power mode */ 185#define ESDHC_FLAG_STATE_LOST_IN_LPMODE BIT(14) 186/* The IP lost clock rate in PM_RUNTIME */ 187#define ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME BIT(15) 188/* 189 * The IP do not support the ACMD23 feature completely when use ADMA mode. 190 * In ADMA mode, it only use the 16 bit block count of the register 0x4 191 * (BLOCK_ATT) as the CMD23's argument for ACMD23 mode, which means it will 192 * ignore the upper 16 bit of the CMD23's argument. This will block the reliable 193 * write operation in RPMB, because RPMB reliable write need to set the bit31 194 * of the CMD23's argument. 195 * imx6qpdl/imx6sx/imx6sl/imx7d has this limitation only for ADMA mode, SDMA 196 * do not has this limitation. so when these SoC use ADMA mode, it need to 197 * disable the ACMD23 feature. 198 */ 199#define ESDHC_FLAG_BROKEN_AUTO_CMD23 BIT(16) 200 201/* ERR004536 is not applicable for the IP */ 202#define ESDHC_FLAG_SKIP_ERR004536 BIT(17) 203 204enum wp_types { 205 ESDHC_WP_NONE, /* no WP, neither controller nor gpio */ 206 ESDHC_WP_CONTROLLER, /* mmc controller internal WP */ 207 ESDHC_WP_GPIO, /* external gpio pin for WP */ 208}; 209 210enum cd_types { 211 ESDHC_CD_NONE, /* no CD, neither controller nor gpio */ 212 ESDHC_CD_CONTROLLER, /* mmc controller internal CD */ 213 ESDHC_CD_GPIO, /* external gpio pin for CD */ 214 ESDHC_CD_PERMANENT, /* no CD, card permanently wired to host */ 215}; 216 217/* 218 * struct esdhc_platform_data - platform data for esdhc on i.MX 219 * 220 * ESDHC_WP(CD)_CONTROLLER type is not available on i.MX25/35. 221 * 222 * @wp_type: type of write_protect method (see wp_types enum above) 223 * @cd_type: type of card_detect method (see cd_types enum above) 224 */ 225 226struct esdhc_platform_data { 227 enum wp_types wp_type; 228 enum cd_types cd_type; 229 int max_bus_width; 230 unsigned int delay_line; 231 unsigned int tuning_step; /* The delay cell steps in tuning procedure */ 232 unsigned int tuning_start_tap; /* The start delay cell point in tuning procedure */ 233 unsigned int strobe_dll_delay_target; /* The delay cell for strobe pad (read clock) */ 234}; 235 236struct esdhc_soc_data { 237 u32 flags; 238}; 239 240static const struct esdhc_soc_data esdhc_imx25_data = { 241 .flags = ESDHC_FLAG_ERR004536, 242}; 243 244static const struct esdhc_soc_data esdhc_imx35_data = { 245 .flags = ESDHC_FLAG_ERR004536, 246}; 247 248static const struct esdhc_soc_data esdhc_imx51_data = { 249 .flags = 0, 250}; 251 252static const struct esdhc_soc_data esdhc_imx53_data = { 253 .flags = ESDHC_FLAG_MULTIBLK_NO_INT, 254}; 255 256static const struct esdhc_soc_data usdhc_imx6q_data = { 257 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING 258 | ESDHC_FLAG_BROKEN_AUTO_CMD23, 259}; 260 261static const struct esdhc_soc_data usdhc_imx6sl_data = { 262 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 263 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_ERR004536 264 | ESDHC_FLAG_HS200 265 | ESDHC_FLAG_BROKEN_AUTO_CMD23, 266}; 267 268static const struct esdhc_soc_data usdhc_imx6sll_data = { 269 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 270 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 271 | ESDHC_FLAG_HS400 272 | ESDHC_FLAG_STATE_LOST_IN_LPMODE, 273}; 274 275static const struct esdhc_soc_data usdhc_imx6sx_data = { 276 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 277 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 278 | ESDHC_FLAG_STATE_LOST_IN_LPMODE 279 | ESDHC_FLAG_BROKEN_AUTO_CMD23, 280}; 281 282static const struct esdhc_soc_data usdhc_imx6ull_data = { 283 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 284 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 285 | ESDHC_FLAG_ERR010450 286 | ESDHC_FLAG_STATE_LOST_IN_LPMODE, 287}; 288 289static const struct esdhc_soc_data usdhc_imx7d_data = { 290 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 291 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 292 | ESDHC_FLAG_HS400 293 | ESDHC_FLAG_STATE_LOST_IN_LPMODE 294 | ESDHC_FLAG_BROKEN_AUTO_CMD23, 295}; 296 297static struct esdhc_soc_data usdhc_s32g2_data = { 298 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_MAN_TUNING 299 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 300 | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES 301 | ESDHC_FLAG_SKIP_ERR004536, 302}; 303 304static struct esdhc_soc_data usdhc_imx7ulp_data = { 305 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 306 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 307 | ESDHC_FLAG_PMQOS | ESDHC_FLAG_HS400 308 | ESDHC_FLAG_STATE_LOST_IN_LPMODE, 309}; 310static struct esdhc_soc_data usdhc_imxrt1050_data = { 311 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 312 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200, 313}; 314 315static struct esdhc_soc_data usdhc_imx8qxp_data = { 316 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 317 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 318 | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES 319 | ESDHC_FLAG_STATE_LOST_IN_LPMODE 320 | ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME, 321}; 322 323static struct esdhc_soc_data usdhc_imx8mm_data = { 324 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 325 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 326 | ESDHC_FLAG_HS400 | ESDHC_FLAG_HS400_ES 327 | ESDHC_FLAG_STATE_LOST_IN_LPMODE, 328}; 329 330struct pltfm_imx_data { 331 u32 scratchpad; 332 struct pinctrl *pinctrl; 333 struct pinctrl_state *pins_100mhz; 334 struct pinctrl_state *pins_200mhz; 335 const struct esdhc_soc_data *socdata; 336 struct esdhc_platform_data boarddata; 337 struct clk *clk_ipg; 338 struct clk *clk_ahb; 339 struct clk *clk_per; 340 unsigned int actual_clock; 341 342 /* 343 * USDHC has one limition, require the SDIO device a different 344 * register setting. Driver has to recognize card type during 345 * the card init, but at this stage, mmc_host->card is not 346 * available. So involve this field to save the card type 347 * during card init through usdhc_init_card(). 348 */ 349 unsigned int init_card_type; 350 351 enum { 352 NO_CMD_PENDING, /* no multiblock command pending */ 353 MULTIBLK_IN_PROCESS, /* exact multiblock cmd in process */ 354 WAIT_FOR_INT, /* sent CMD12, waiting for response INT */ 355 } multiblock_status; 356 u32 is_ddr; 357 struct pm_qos_request pm_qos_req; 358}; 359 360static const struct of_device_id imx_esdhc_dt_ids[] = { 361 { .compatible = "fsl,imx25-esdhc", .data = &esdhc_imx25_data, }, 362 { .compatible = "fsl,imx35-esdhc", .data = &esdhc_imx35_data, }, 363 { .compatible = "fsl,imx51-esdhc", .data = &esdhc_imx51_data, }, 364 { .compatible = "fsl,imx53-esdhc", .data = &esdhc_imx53_data, }, 365 { .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, }, 366 { .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, }, 367 { .compatible = "fsl,imx6sll-usdhc", .data = &usdhc_imx6sll_data, }, 368 { .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, }, 369 { .compatible = "fsl,imx6ull-usdhc", .data = &usdhc_imx6ull_data, }, 370 { .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, }, 371 { .compatible = "fsl,imx7ulp-usdhc", .data = &usdhc_imx7ulp_data, }, 372 { .compatible = "fsl,imx8qxp-usdhc", .data = &usdhc_imx8qxp_data, }, 373 { .compatible = "fsl,imx8mm-usdhc", .data = &usdhc_imx8mm_data, }, 374 { .compatible = "fsl,imxrt1050-usdhc", .data = &usdhc_imxrt1050_data, }, 375 { .compatible = "nxp,s32g2-usdhc", .data = &usdhc_s32g2_data, }, 376 { /* sentinel */ } 377}; 378MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids); 379 380static inline int is_imx25_esdhc(struct pltfm_imx_data *data) 381{ 382 return data->socdata == &esdhc_imx25_data; 383} 384 385static inline int is_imx53_esdhc(struct pltfm_imx_data *data) 386{ 387 return data->socdata == &esdhc_imx53_data; 388} 389 390static inline int esdhc_is_usdhc(struct pltfm_imx_data *data) 391{ 392 return !!(data->socdata->flags & ESDHC_FLAG_USDHC); 393} 394 395static inline void esdhc_clrset_le(struct sdhci_host *host, u32 mask, u32 val, int reg) 396{ 397 void __iomem *base = host->ioaddr + (reg & ~0x3); 398 u32 shift = (reg & 0x3) * 8; 399 400 writel(((readl(base) & ~(mask << shift)) | (val << shift)), base); 401} 402 403#define DRIVER_NAME "sdhci-esdhc-imx" 404#define ESDHC_IMX_DUMP(f, x...) \ 405 pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x) 406static void esdhc_dump_debug_regs(struct sdhci_host *host) 407{ 408 int i; 409 char *debug_status[7] = { 410 "cmd debug status", 411 "data debug status", 412 "trans debug status", 413 "dma debug status", 414 "adma debug status", 415 "fifo debug status", 416 "async fifo debug status" 417 }; 418 419 ESDHC_IMX_DUMP("========= ESDHC IMX DEBUG STATUS DUMP =========\n"); 420 for (i = 0; i < 7; i++) { 421 esdhc_clrset_le(host, ESDHC_DEBUG_SEL_MASK, 422 ESDHC_DEBUG_SEL_CMD_STATE + i, ESDHC_DEBUG_SEL_REG); 423 ESDHC_IMX_DUMP("%s: 0x%04x\n", debug_status[i], 424 readw(host->ioaddr + ESDHC_DEBUG_SEL_AND_STATUS_REG)); 425 } 426 427 esdhc_clrset_le(host, ESDHC_DEBUG_SEL_MASK, 0, ESDHC_DEBUG_SEL_REG); 428 429} 430 431static inline void esdhc_wait_for_card_clock_gate_off(struct sdhci_host *host) 432{ 433 u32 present_state; 434 int ret; 435 436 ret = readl_poll_timeout(host->ioaddr + ESDHC_PRSSTAT, present_state, 437 (present_state & ESDHC_CLOCK_GATE_OFF), 2, 100); 438 if (ret == -ETIMEDOUT) 439 dev_warn(mmc_dev(host->mmc), "%s: card clock still not gate off in 100us!.\n", __func__); 440} 441 442/* Enable the auto tuning circuit to check the CMD line and BUS line */ 443static inline void usdhc_auto_tuning_mode_sel_and_en(struct sdhci_host *host) 444{ 445 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 446 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 447 u32 buswidth, auto_tune_buswidth; 448 u32 reg; 449 450 buswidth = USDHC_GET_BUSWIDTH(readl(host->ioaddr + SDHCI_HOST_CONTROL)); 451 452 switch (buswidth) { 453 case ESDHC_CTRL_8BITBUS: 454 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_8BIT_EN; 455 break; 456 case ESDHC_CTRL_4BITBUS: 457 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_4BIT_EN; 458 break; 459 default: /* 1BITBUS */ 460 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN; 461 break; 462 } 463 464 /* 465 * For USDHC, auto tuning circuit can not handle the async sdio 466 * device interrupt correctly. When sdio device use 4 data lines, 467 * async sdio interrupt will use the shared DAT[1], if enable auto 468 * tuning circuit check these 4 data lines, include the DAT[1], 469 * this circuit will detect this interrupt, take this as a data on 470 * DAT[1], and adjust the delay cell wrongly. 471 * This is the hardware design limitation, to avoid this, for sdio 472 * device, config the auto tuning circuit only check DAT[0] and CMD 473 * line. 474 */ 475 if (imx_data->init_card_type == MMC_TYPE_SDIO) 476 auto_tune_buswidth = ESDHC_VEND_SPEC2_AUTO_TUNE_1BIT_EN; 477 478 esdhc_clrset_le(host, ESDHC_VEND_SPEC2_AUTO_TUNE_MODE_MASK, 479 auto_tune_buswidth | ESDHC_VEND_SPEC2_AUTO_TUNE_CMD_EN, 480 ESDHC_VEND_SPEC2); 481 482 reg = readl(host->ioaddr + ESDHC_MIX_CTRL); 483 reg |= ESDHC_MIX_CTRL_AUTO_TUNE_EN; 484 writel(reg, host->ioaddr + ESDHC_MIX_CTRL); 485} 486 487static u32 esdhc_readl_le(struct sdhci_host *host, int reg) 488{ 489 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 490 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 491 u32 val = readl(host->ioaddr + reg); 492 493 if (unlikely(reg == SDHCI_PRESENT_STATE)) { 494 u32 fsl_prss = val; 495 /* save the least 20 bits */ 496 val = fsl_prss & 0x000FFFFF; 497 /* move dat[0-3] bits */ 498 val |= (fsl_prss & 0x0F000000) >> 4; 499 /* move cmd line bit */ 500 val |= (fsl_prss & 0x00800000) << 1; 501 } 502 503 if (unlikely(reg == SDHCI_CAPABILITIES)) { 504 /* ignore bit[0-15] as it stores cap_1 register val for mx6sl */ 505 if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1) 506 val &= 0xffff0000; 507 508 /* In FSL esdhc IC module, only bit20 is used to indicate the 509 * ADMA2 capability of esdhc, but this bit is messed up on 510 * some SOCs (e.g. on MX25, MX35 this bit is set, but they 511 * don't actually support ADMA2). So set the BROKEN_ADMA 512 * quirk on MX25/35 platforms. 513 */ 514 515 if (val & SDHCI_CAN_DO_ADMA1) { 516 val &= ~SDHCI_CAN_DO_ADMA1; 517 val |= SDHCI_CAN_DO_ADMA2; 518 } 519 } 520 521 if (unlikely(reg == SDHCI_CAPABILITIES_1)) { 522 if (esdhc_is_usdhc(imx_data)) { 523 if (imx_data->socdata->flags & ESDHC_FLAG_HAVE_CAP1) 524 val = readl(host->ioaddr + SDHCI_CAPABILITIES) & 0xFFFF; 525 else 526 /* imx6q/dl does not have cap_1 register, fake one */ 527 val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104 528 | SDHCI_SUPPORT_SDR50 529 | SDHCI_USE_SDR50_TUNING 530 | FIELD_PREP(SDHCI_RETUNING_MODE_MASK, 531 SDHCI_TUNING_MODE_3); 532 533 /* 534 * Do not advertise faster UHS modes if there are no 535 * pinctrl states for 100MHz/200MHz. 536 */ 537 if (IS_ERR_OR_NULL(imx_data->pins_100mhz)) 538 val &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50); 539 if (IS_ERR_OR_NULL(imx_data->pins_200mhz)) 540 val &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_HS400); 541 } 542 } 543 544 if (unlikely(reg == SDHCI_MAX_CURRENT) && esdhc_is_usdhc(imx_data)) { 545 val = 0; 546 val |= FIELD_PREP(SDHCI_MAX_CURRENT_330_MASK, 0xFF); 547 val |= FIELD_PREP(SDHCI_MAX_CURRENT_300_MASK, 0xFF); 548 val |= FIELD_PREP(SDHCI_MAX_CURRENT_180_MASK, 0xFF); 549 } 550 551 if (unlikely(reg == SDHCI_INT_STATUS)) { 552 if (val & ESDHC_INT_VENDOR_SPEC_DMA_ERR) { 553 val &= ~ESDHC_INT_VENDOR_SPEC_DMA_ERR; 554 val |= SDHCI_INT_ADMA_ERROR; 555 } 556 557 /* 558 * mask off the interrupt we get in response to the manually 559 * sent CMD12 560 */ 561 if ((imx_data->multiblock_status == WAIT_FOR_INT) && 562 ((val & SDHCI_INT_RESPONSE) == SDHCI_INT_RESPONSE)) { 563 val &= ~SDHCI_INT_RESPONSE; 564 writel(SDHCI_INT_RESPONSE, host->ioaddr + 565 SDHCI_INT_STATUS); 566 imx_data->multiblock_status = NO_CMD_PENDING; 567 } 568 } 569 570 return val; 571} 572 573static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg) 574{ 575 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 576 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 577 u32 data; 578 579 if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE || 580 reg == SDHCI_INT_STATUS)) { 581 if ((val & SDHCI_INT_CARD_INT) && !esdhc_is_usdhc(imx_data)) { 582 /* 583 * Clear and then set D3CD bit to avoid missing the 584 * card interrupt. This is an eSDHC controller problem 585 * so we need to apply the following workaround: clear 586 * and set D3CD bit will make eSDHC re-sample the card 587 * interrupt. In case a card interrupt was lost, 588 * re-sample it by the following steps. 589 */ 590 data = readl(host->ioaddr + SDHCI_HOST_CONTROL); 591 data &= ~ESDHC_CTRL_D3CD; 592 writel(data, host->ioaddr + SDHCI_HOST_CONTROL); 593 data |= ESDHC_CTRL_D3CD; 594 writel(data, host->ioaddr + SDHCI_HOST_CONTROL); 595 } 596 597 if (val & SDHCI_INT_ADMA_ERROR) { 598 val &= ~SDHCI_INT_ADMA_ERROR; 599 val |= ESDHC_INT_VENDOR_SPEC_DMA_ERR; 600 } 601 } 602 603 if (unlikely((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT) 604 && (reg == SDHCI_INT_STATUS) 605 && (val & SDHCI_INT_DATA_END))) { 606 u32 v; 607 v = readl(host->ioaddr + ESDHC_VENDOR_SPEC); 608 v &= ~ESDHC_VENDOR_SPEC_SDIO_QUIRK; 609 writel(v, host->ioaddr + ESDHC_VENDOR_SPEC); 610 611 if (imx_data->multiblock_status == MULTIBLK_IN_PROCESS) 612 { 613 /* send a manual CMD12 with RESPTYP=none */ 614 data = MMC_STOP_TRANSMISSION << 24 | 615 SDHCI_CMD_ABORTCMD << 16; 616 writel(data, host->ioaddr + SDHCI_TRANSFER_MODE); 617 imx_data->multiblock_status = WAIT_FOR_INT; 618 } 619 } 620 621 writel(val, host->ioaddr + reg); 622} 623 624static u16 esdhc_readw_le(struct sdhci_host *host, int reg) 625{ 626 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 627 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 628 u16 ret = 0; 629 u32 val; 630 631 if (unlikely(reg == SDHCI_HOST_VERSION)) { 632 reg ^= 2; 633 if (esdhc_is_usdhc(imx_data)) { 634 /* 635 * The usdhc register returns a wrong host version. 636 * Correct it here. 637 */ 638 return SDHCI_SPEC_300; 639 } 640 } 641 642 if (unlikely(reg == SDHCI_HOST_CONTROL2)) { 643 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); 644 if (val & ESDHC_VENDOR_SPEC_VSELECT) 645 ret |= SDHCI_CTRL_VDD_180; 646 647 if (esdhc_is_usdhc(imx_data)) { 648 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) 649 val = readl(host->ioaddr + ESDHC_MIX_CTRL); 650 else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) 651 /* the std tuning bits is in ACMD12_ERR for imx6sl */ 652 val = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS); 653 } 654 655 if (val & ESDHC_MIX_CTRL_EXE_TUNE) 656 ret |= SDHCI_CTRL_EXEC_TUNING; 657 if (val & ESDHC_MIX_CTRL_SMPCLK_SEL) 658 ret |= SDHCI_CTRL_TUNED_CLK; 659 660 ret &= ~SDHCI_CTRL_PRESET_VAL_ENABLE; 661 662 return ret; 663 } 664 665 if (unlikely(reg == SDHCI_TRANSFER_MODE)) { 666 if (esdhc_is_usdhc(imx_data)) { 667 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL); 668 ret = m & ESDHC_MIX_CTRL_SDHCI_MASK; 669 /* Swap AC23 bit */ 670 if (m & ESDHC_MIX_CTRL_AC23EN) { 671 ret &= ~ESDHC_MIX_CTRL_AC23EN; 672 ret |= SDHCI_TRNS_AUTO_CMD23; 673 } 674 } else { 675 ret = readw(host->ioaddr + SDHCI_TRANSFER_MODE); 676 } 677 678 return ret; 679 } 680 681 return readw(host->ioaddr + reg); 682} 683 684static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg) 685{ 686 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 687 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 688 u32 new_val = 0; 689 690 switch (reg) { 691 case SDHCI_CLOCK_CONTROL: 692 new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); 693 if (val & SDHCI_CLOCK_CARD_EN) 694 new_val |= ESDHC_VENDOR_SPEC_FRC_SDCLK_ON; 695 else 696 new_val &= ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON; 697 writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC); 698 if (!(new_val & ESDHC_VENDOR_SPEC_FRC_SDCLK_ON)) 699 esdhc_wait_for_card_clock_gate_off(host); 700 return; 701 case SDHCI_HOST_CONTROL2: 702 new_val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); 703 if (val & SDHCI_CTRL_VDD_180) 704 new_val |= ESDHC_VENDOR_SPEC_VSELECT; 705 else 706 new_val &= ~ESDHC_VENDOR_SPEC_VSELECT; 707 writel(new_val, host->ioaddr + ESDHC_VENDOR_SPEC); 708 if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) { 709 u32 v = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS); 710 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL); 711 if (val & SDHCI_CTRL_TUNED_CLK) { 712 v |= ESDHC_MIX_CTRL_SMPCLK_SEL; 713 } else { 714 v &= ~ESDHC_MIX_CTRL_SMPCLK_SEL; 715 m &= ~ESDHC_MIX_CTRL_FBCLK_SEL; 716 } 717 718 if (val & SDHCI_CTRL_EXEC_TUNING) { 719 v |= ESDHC_MIX_CTRL_EXE_TUNE; 720 m |= ESDHC_MIX_CTRL_FBCLK_SEL; 721 } else { 722 v &= ~ESDHC_MIX_CTRL_EXE_TUNE; 723 } 724 725 writel(v, host->ioaddr + SDHCI_AUTO_CMD_STATUS); 726 writel(m, host->ioaddr + ESDHC_MIX_CTRL); 727 } 728 return; 729 case SDHCI_TRANSFER_MODE: 730 if ((imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT) 731 && (host->cmd->opcode == SD_IO_RW_EXTENDED) 732 && (host->cmd->data->blocks > 1) 733 && (host->cmd->data->flags & MMC_DATA_READ)) { 734 u32 v; 735 v = readl(host->ioaddr + ESDHC_VENDOR_SPEC); 736 v |= ESDHC_VENDOR_SPEC_SDIO_QUIRK; 737 writel(v, host->ioaddr + ESDHC_VENDOR_SPEC); 738 } 739 740 if (esdhc_is_usdhc(imx_data)) { 741 u32 wml; 742 u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL); 743 /* Swap AC23 bit */ 744 if (val & SDHCI_TRNS_AUTO_CMD23) { 745 val &= ~SDHCI_TRNS_AUTO_CMD23; 746 val |= ESDHC_MIX_CTRL_AC23EN; 747 } 748 m = val | (m & ~ESDHC_MIX_CTRL_SDHCI_MASK); 749 writel(m, host->ioaddr + ESDHC_MIX_CTRL); 750 751 /* Set watermark levels for PIO access to maximum value 752 * (128 words) to accommodate full 512 bytes buffer. 753 * For DMA access restore the levels to default value. 754 */ 755 m = readl(host->ioaddr + ESDHC_WTMK_LVL); 756 if (val & SDHCI_TRNS_DMA) { 757 wml = ESDHC_WTMK_LVL_WML_VAL_DEF; 758 } else { 759 u8 ctrl; 760 wml = ESDHC_WTMK_LVL_WML_VAL_MAX; 761 762 /* 763 * Since already disable DMA mode, so also need 764 * to clear the DMASEL. Otherwise, for standard 765 * tuning, when send tuning command, usdhc will 766 * still prefetch the ADMA script from wrong 767 * DMA address, then we will see IOMMU report 768 * some error which show lack of TLB mapping. 769 */ 770 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL); 771 ctrl &= ~SDHCI_CTRL_DMA_MASK; 772 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL); 773 } 774 m &= ~(ESDHC_WTMK_LVL_RD_WML_MASK | 775 ESDHC_WTMK_LVL_WR_WML_MASK); 776 m |= (wml << ESDHC_WTMK_LVL_RD_WML_SHIFT) | 777 (wml << ESDHC_WTMK_LVL_WR_WML_SHIFT); 778 writel(m, host->ioaddr + ESDHC_WTMK_LVL); 779 } else { 780 /* 781 * Postpone this write, we must do it together with a 782 * command write that is down below. 783 */ 784 imx_data->scratchpad = val; 785 } 786 return; 787 case SDHCI_COMMAND: 788 if (host->cmd->opcode == MMC_STOP_TRANSMISSION) 789 val |= SDHCI_CMD_ABORTCMD; 790 791 if ((host->cmd->opcode == MMC_SET_BLOCK_COUNT) && 792 (imx_data->socdata->flags & ESDHC_FLAG_MULTIBLK_NO_INT)) 793 imx_data->multiblock_status = MULTIBLK_IN_PROCESS; 794 795 if (esdhc_is_usdhc(imx_data)) 796 writel(val << 16, 797 host->ioaddr + SDHCI_TRANSFER_MODE); 798 else 799 writel(val << 16 | imx_data->scratchpad, 800 host->ioaddr + SDHCI_TRANSFER_MODE); 801 return; 802 case SDHCI_BLOCK_SIZE: 803 val &= ~SDHCI_MAKE_BLKSZ(0x7, 0); 804 break; 805 } 806 esdhc_clrset_le(host, 0xffff, val, reg); 807} 808 809static u8 esdhc_readb_le(struct sdhci_host *host, int reg) 810{ 811 u8 ret; 812 u32 val; 813 814 switch (reg) { 815 case SDHCI_HOST_CONTROL: 816 val = readl(host->ioaddr + reg); 817 818 ret = val & SDHCI_CTRL_LED; 819 ret |= (val >> 5) & SDHCI_CTRL_DMA_MASK; 820 ret |= (val & ESDHC_CTRL_4BITBUS); 821 ret |= (val & ESDHC_CTRL_8BITBUS) << 3; 822 return ret; 823 } 824 825 return readb(host->ioaddr + reg); 826} 827 828static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg) 829{ 830 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 831 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 832 u32 new_val = 0; 833 u32 mask; 834 835 switch (reg) { 836 case SDHCI_POWER_CONTROL: 837 /* 838 * FSL put some DMA bits here 839 * If your board has a regulator, code should be here 840 */ 841 return; 842 case SDHCI_HOST_CONTROL: 843 /* FSL messed up here, so we need to manually compose it. */ 844 new_val = val & SDHCI_CTRL_LED; 845 /* ensure the endianness */ 846 new_val |= ESDHC_HOST_CONTROL_LE; 847 /* bits 8&9 are reserved on mx25 */ 848 if (!is_imx25_esdhc(imx_data)) { 849 /* DMA mode bits are shifted */ 850 new_val |= (val & SDHCI_CTRL_DMA_MASK) << 5; 851 } 852 853 /* 854 * Do not touch buswidth bits here. This is done in 855 * esdhc_pltfm_bus_width. 856 * Do not touch the D3CD bit either which is used for the 857 * SDIO interrupt erratum workaround. 858 */ 859 mask = 0xffff & ~(ESDHC_CTRL_BUSWIDTH_MASK | ESDHC_CTRL_D3CD); 860 861 esdhc_clrset_le(host, mask, new_val, reg); 862 return; 863 case SDHCI_SOFTWARE_RESET: 864 if (val & SDHCI_RESET_DATA) 865 new_val = readl(host->ioaddr + SDHCI_HOST_CONTROL); 866 break; 867 } 868 esdhc_clrset_le(host, 0xff, val, reg); 869 870 if (reg == SDHCI_SOFTWARE_RESET) { 871 if (val & SDHCI_RESET_ALL) { 872 /* 873 * The esdhc has a design violation to SDHC spec which 874 * tells that software reset should not affect card 875 * detection circuit. But esdhc clears its SYSCTL 876 * register bits [0..2] during the software reset. This 877 * will stop those clocks that card detection circuit 878 * relies on. To work around it, we turn the clocks on 879 * back to keep card detection circuit functional. 880 */ 881 esdhc_clrset_le(host, 0x7, 0x7, ESDHC_SYSTEM_CONTROL); 882 /* 883 * The reset on usdhc fails to clear MIX_CTRL register. 884 * Do it manually here. 885 */ 886 if (esdhc_is_usdhc(imx_data)) { 887 /* 888 * the tuning bits should be kept during reset 889 */ 890 new_val = readl(host->ioaddr + ESDHC_MIX_CTRL); 891 writel(new_val & ESDHC_MIX_CTRL_TUNING_MASK, 892 host->ioaddr + ESDHC_MIX_CTRL); 893 imx_data->is_ddr = 0; 894 } 895 } else if (val & SDHCI_RESET_DATA) { 896 /* 897 * The eSDHC DAT line software reset clears at least the 898 * data transfer width on i.MX25, so make sure that the 899 * Host Control register is unaffected. 900 */ 901 esdhc_clrset_le(host, 0xff, new_val, 902 SDHCI_HOST_CONTROL); 903 } 904 } 905} 906 907static unsigned int esdhc_pltfm_get_max_clock(struct sdhci_host *host) 908{ 909 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 910 911 return pltfm_host->clock; 912} 913 914static unsigned int esdhc_pltfm_get_min_clock(struct sdhci_host *host) 915{ 916 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 917 918 return pltfm_host->clock / 256 / 16; 919} 920 921static inline void esdhc_pltfm_set_clock(struct sdhci_host *host, 922 unsigned int clock) 923{ 924 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 925 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 926 unsigned int host_clock = pltfm_host->clock; 927 int ddr_pre_div = imx_data->is_ddr ? 2 : 1; 928 int pre_div = 1; 929 int div = 1; 930 int ret; 931 u32 temp, val; 932 933 if (esdhc_is_usdhc(imx_data)) { 934 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); 935 writel(val & ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON, 936 host->ioaddr + ESDHC_VENDOR_SPEC); 937 esdhc_wait_for_card_clock_gate_off(host); 938 } 939 940 if (clock == 0) { 941 host->mmc->actual_clock = 0; 942 return; 943 } 944 945 /* For i.MX53 eSDHCv3, SYSCTL.SDCLKFS may not be set to 0. */ 946 if (is_imx53_esdhc(imx_data)) { 947 /* 948 * According to the i.MX53 reference manual, if DLLCTRL[10] can 949 * be set, then the controller is eSDHCv3, else it is eSDHCv2. 950 */ 951 val = readl(host->ioaddr + ESDHC_DLL_CTRL); 952 writel(val | BIT(10), host->ioaddr + ESDHC_DLL_CTRL); 953 temp = readl(host->ioaddr + ESDHC_DLL_CTRL); 954 writel(val, host->ioaddr + ESDHC_DLL_CTRL); 955 if (temp & BIT(10)) 956 pre_div = 2; 957 } 958 959 temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL); 960 temp &= ~(ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN 961 | ESDHC_CLOCK_MASK); 962 sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL); 963 964 if ((imx_data->socdata->flags & ESDHC_FLAG_ERR010450) && 965 (!(host->quirks2 & SDHCI_QUIRK2_NO_1_8_V))) { 966 unsigned int max_clock; 967 968 max_clock = imx_data->is_ddr ? 45000000 : 150000000; 969 970 clock = min(clock, max_clock); 971 } 972 973 while (host_clock / (16 * pre_div * ddr_pre_div) > clock && 974 pre_div < 256) 975 pre_div *= 2; 976 977 while (host_clock / (div * pre_div * ddr_pre_div) > clock && div < 16) 978 div++; 979 980 host->mmc->actual_clock = host_clock / (div * pre_div * ddr_pre_div); 981 dev_dbg(mmc_dev(host->mmc), "desired SD clock: %d, actual: %d\n", 982 clock, host->mmc->actual_clock); 983 984 pre_div >>= 1; 985 div--; 986 987 temp = sdhci_readl(host, ESDHC_SYSTEM_CONTROL); 988 temp |= (ESDHC_CLOCK_IPGEN | ESDHC_CLOCK_HCKEN | ESDHC_CLOCK_PEREN 989 | (div << ESDHC_DIVIDER_SHIFT) 990 | (pre_div << ESDHC_PREDIV_SHIFT)); 991 sdhci_writel(host, temp, ESDHC_SYSTEM_CONTROL); 992 993 /* need to wait the bit 3 of the PRSSTAT to be set, make sure card clock is stable */ 994 ret = readl_poll_timeout(host->ioaddr + ESDHC_PRSSTAT, temp, 995 (temp & ESDHC_CLOCK_STABLE), 2, 100); 996 if (ret == -ETIMEDOUT) 997 dev_warn(mmc_dev(host->mmc), "card clock still not stable in 100us!.\n"); 998 999 if (esdhc_is_usdhc(imx_data)) { 1000 val = readl(host->ioaddr + ESDHC_VENDOR_SPEC); 1001 writel(val | ESDHC_VENDOR_SPEC_FRC_SDCLK_ON, 1002 host->ioaddr + ESDHC_VENDOR_SPEC); 1003 } 1004 1005} 1006 1007static unsigned int esdhc_pltfm_get_ro(struct sdhci_host *host) 1008{ 1009 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1010 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1011 struct esdhc_platform_data *boarddata = &imx_data->boarddata; 1012 1013 switch (boarddata->wp_type) { 1014 case ESDHC_WP_GPIO: 1015 return mmc_gpio_get_ro(host->mmc); 1016 case ESDHC_WP_CONTROLLER: 1017 return !(readl(host->ioaddr + SDHCI_PRESENT_STATE) & 1018 SDHCI_WRITE_PROTECT); 1019 case ESDHC_WP_NONE: 1020 break; 1021 } 1022 1023 return -ENOSYS; 1024} 1025 1026static void esdhc_pltfm_set_bus_width(struct sdhci_host *host, int width) 1027{ 1028 u32 ctrl; 1029 1030 switch (width) { 1031 case MMC_BUS_WIDTH_8: 1032 ctrl = ESDHC_CTRL_8BITBUS; 1033 break; 1034 case MMC_BUS_WIDTH_4: 1035 ctrl = ESDHC_CTRL_4BITBUS; 1036 break; 1037 default: 1038 ctrl = 0; 1039 break; 1040 } 1041 1042 esdhc_clrset_le(host, ESDHC_CTRL_BUSWIDTH_MASK, ctrl, 1043 SDHCI_HOST_CONTROL); 1044} 1045 1046static void esdhc_reset_tuning(struct sdhci_host *host) 1047{ 1048 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1049 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1050 u32 ctrl; 1051 int ret; 1052 1053 /* Reset the tuning circuit */ 1054 if (esdhc_is_usdhc(imx_data)) { 1055 ctrl = readl(host->ioaddr + ESDHC_MIX_CTRL); 1056 ctrl &= ~ESDHC_MIX_CTRL_AUTO_TUNE_EN; 1057 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) { 1058 ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL; 1059 ctrl &= ~ESDHC_MIX_CTRL_FBCLK_SEL; 1060 writel(ctrl, host->ioaddr + ESDHC_MIX_CTRL); 1061 writel(0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS); 1062 } else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) { 1063 writel(ctrl, host->ioaddr + ESDHC_MIX_CTRL); 1064 ctrl = readl(host->ioaddr + SDHCI_AUTO_CMD_STATUS); 1065 ctrl &= ~ESDHC_MIX_CTRL_SMPCLK_SEL; 1066 ctrl &= ~ESDHC_MIX_CTRL_EXE_TUNE; 1067 writel(ctrl, host->ioaddr + SDHCI_AUTO_CMD_STATUS); 1068 /* Make sure ESDHC_MIX_CTRL_EXE_TUNE cleared */ 1069 ret = readl_poll_timeout(host->ioaddr + SDHCI_AUTO_CMD_STATUS, 1070 ctrl, !(ctrl & ESDHC_MIX_CTRL_EXE_TUNE), 1, 50); 1071 if (ret == -ETIMEDOUT) 1072 dev_warn(mmc_dev(host->mmc), 1073 "Warning! clear execute tuning bit failed\n"); 1074 /* 1075 * SDHCI_INT_DATA_AVAIL is W1C bit, set this bit will clear the 1076 * usdhc IP internal logic flag execute_tuning_with_clr_buf, which 1077 * will finally make sure the normal data transfer logic correct. 1078 */ 1079 ctrl = readl(host->ioaddr + SDHCI_INT_STATUS); 1080 ctrl |= SDHCI_INT_DATA_AVAIL; 1081 writel(ctrl, host->ioaddr + SDHCI_INT_STATUS); 1082 } 1083 } 1084} 1085 1086static void usdhc_init_card(struct mmc_host *mmc, struct mmc_card *card) 1087{ 1088 struct sdhci_host *host = mmc_priv(mmc); 1089 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1090 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1091 1092 imx_data->init_card_type = card->type; 1093} 1094 1095static int usdhc_execute_tuning(struct mmc_host *mmc, u32 opcode) 1096{ 1097 struct sdhci_host *host = mmc_priv(mmc); 1098 int err; 1099 1100 /* 1101 * i.MX uSDHC internally already uses a fixed optimized timing for 1102 * DDR50, normally does not require tuning for DDR50 mode. 1103 */ 1104 if (host->timing == MMC_TIMING_UHS_DDR50) 1105 return 0; 1106 1107 /* 1108 * Reset tuning circuit logic. If not, the previous tuning result 1109 * will impact current tuning, make current tuning can't set the 1110 * correct delay cell. 1111 */ 1112 esdhc_reset_tuning(host); 1113 err = sdhci_execute_tuning(mmc, opcode); 1114 /* If tuning done, enable auto tuning */ 1115 if (!err && !host->tuning_err) 1116 usdhc_auto_tuning_mode_sel_and_en(host); 1117 1118 return err; 1119} 1120 1121static void esdhc_prepare_tuning(struct sdhci_host *host, u32 val) 1122{ 1123 u32 reg; 1124 u8 sw_rst; 1125 int ret; 1126 1127 /* FIXME: delay a bit for card to be ready for next tuning due to errors */ 1128 mdelay(1); 1129 1130 /* IC suggest to reset USDHC before every tuning command */ 1131 esdhc_clrset_le(host, 0xff, SDHCI_RESET_ALL, SDHCI_SOFTWARE_RESET); 1132 ret = readb_poll_timeout(host->ioaddr + SDHCI_SOFTWARE_RESET, sw_rst, 1133 !(sw_rst & SDHCI_RESET_ALL), 10, 100); 1134 if (ret == -ETIMEDOUT) 1135 dev_warn(mmc_dev(host->mmc), 1136 "warning! RESET_ALL never complete before sending tuning command\n"); 1137 1138 reg = readl(host->ioaddr + ESDHC_MIX_CTRL); 1139 reg |= ESDHC_MIX_CTRL_EXE_TUNE | ESDHC_MIX_CTRL_SMPCLK_SEL | 1140 ESDHC_MIX_CTRL_FBCLK_SEL; 1141 writel(reg, host->ioaddr + ESDHC_MIX_CTRL); 1142 writel(val << 8, host->ioaddr + ESDHC_TUNE_CTRL_STATUS); 1143 dev_dbg(mmc_dev(host->mmc), 1144 "tuning with delay 0x%x ESDHC_TUNE_CTRL_STATUS 0x%x\n", 1145 val, readl(host->ioaddr + ESDHC_TUNE_CTRL_STATUS)); 1146} 1147 1148static void esdhc_post_tuning(struct sdhci_host *host) 1149{ 1150 u32 reg; 1151 1152 reg = readl(host->ioaddr + ESDHC_MIX_CTRL); 1153 reg &= ~ESDHC_MIX_CTRL_EXE_TUNE; 1154 writel(reg, host->ioaddr + ESDHC_MIX_CTRL); 1155} 1156 1157static int esdhc_executing_tuning(struct sdhci_host *host, u32 opcode) 1158{ 1159 int min, max, avg, ret; 1160 1161 /* find the mininum delay first which can pass tuning */ 1162 min = ESDHC_TUNE_CTRL_MIN; 1163 while (min < ESDHC_TUNE_CTRL_MAX) { 1164 esdhc_prepare_tuning(host, min); 1165 if (!mmc_send_tuning(host->mmc, opcode, NULL)) 1166 break; 1167 min += ESDHC_TUNE_CTRL_STEP; 1168 } 1169 1170 /* find the maxinum delay which can not pass tuning */ 1171 max = min + ESDHC_TUNE_CTRL_STEP; 1172 while (max < ESDHC_TUNE_CTRL_MAX) { 1173 esdhc_prepare_tuning(host, max); 1174 if (mmc_send_tuning(host->mmc, opcode, NULL)) { 1175 max -= ESDHC_TUNE_CTRL_STEP; 1176 break; 1177 } 1178 max += ESDHC_TUNE_CTRL_STEP; 1179 } 1180 1181 /* use average delay to get the best timing */ 1182 avg = (min + max) / 2; 1183 esdhc_prepare_tuning(host, avg); 1184 ret = mmc_send_tuning(host->mmc, opcode, NULL); 1185 esdhc_post_tuning(host); 1186 1187 dev_dbg(mmc_dev(host->mmc), "tuning %s at 0x%x ret %d\n", 1188 ret ? "failed" : "passed", avg, ret); 1189 1190 return ret; 1191} 1192 1193static void esdhc_hs400_enhanced_strobe(struct mmc_host *mmc, struct mmc_ios *ios) 1194{ 1195 struct sdhci_host *host = mmc_priv(mmc); 1196 u32 m; 1197 1198 m = readl(host->ioaddr + ESDHC_MIX_CTRL); 1199 if (ios->enhanced_strobe) 1200 m |= ESDHC_MIX_CTRL_HS400_ES_EN; 1201 else 1202 m &= ~ESDHC_MIX_CTRL_HS400_ES_EN; 1203 writel(m, host->ioaddr + ESDHC_MIX_CTRL); 1204} 1205 1206static int esdhc_change_pinstate(struct sdhci_host *host, 1207 unsigned int uhs) 1208{ 1209 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1210 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1211 struct pinctrl_state *pinctrl; 1212 1213 dev_dbg(mmc_dev(host->mmc), "change pinctrl state for uhs %d\n", uhs); 1214 1215 if (IS_ERR(imx_data->pinctrl) || 1216 IS_ERR(imx_data->pins_100mhz) || 1217 IS_ERR(imx_data->pins_200mhz)) 1218 return -EINVAL; 1219 1220 switch (uhs) { 1221 case MMC_TIMING_UHS_SDR50: 1222 case MMC_TIMING_UHS_DDR50: 1223 pinctrl = imx_data->pins_100mhz; 1224 break; 1225 case MMC_TIMING_UHS_SDR104: 1226 case MMC_TIMING_MMC_HS200: 1227 case MMC_TIMING_MMC_HS400: 1228 pinctrl = imx_data->pins_200mhz; 1229 break; 1230 default: 1231 /* back to default state for other legacy timing */ 1232 return pinctrl_select_default_state(mmc_dev(host->mmc)); 1233 } 1234 1235 return pinctrl_select_state(imx_data->pinctrl, pinctrl); 1236} 1237 1238/* 1239 * For HS400 eMMC, there is a data_strobe line. This signal is generated 1240 * by the device and used for data output and CRC status response output 1241 * in HS400 mode. The frequency of this signal follows the frequency of 1242 * CLK generated by host. The host receives the data which is aligned to the 1243 * edge of data_strobe line. Due to the time delay between CLK line and 1244 * data_strobe line, if the delay time is larger than one clock cycle, 1245 * then CLK and data_strobe line will be misaligned, read error shows up. 1246 */ 1247static void esdhc_set_strobe_dll(struct sdhci_host *host) 1248{ 1249 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1250 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1251 u32 strobe_delay; 1252 u32 v; 1253 int ret; 1254 1255 /* disable clock before enabling strobe dll */ 1256 writel(readl(host->ioaddr + ESDHC_VENDOR_SPEC) & 1257 ~ESDHC_VENDOR_SPEC_FRC_SDCLK_ON, 1258 host->ioaddr + ESDHC_VENDOR_SPEC); 1259 esdhc_wait_for_card_clock_gate_off(host); 1260 1261 /* force a reset on strobe dll */ 1262 writel(ESDHC_STROBE_DLL_CTRL_RESET, 1263 host->ioaddr + ESDHC_STROBE_DLL_CTRL); 1264 /* clear the reset bit on strobe dll before any setting */ 1265 writel(0, host->ioaddr + ESDHC_STROBE_DLL_CTRL); 1266 1267 /* 1268 * enable strobe dll ctrl and adjust the delay target 1269 * for the uSDHC loopback read clock 1270 */ 1271 if (imx_data->boarddata.strobe_dll_delay_target) 1272 strobe_delay = imx_data->boarddata.strobe_dll_delay_target; 1273 else 1274 strobe_delay = ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT; 1275 v = ESDHC_STROBE_DLL_CTRL_ENABLE | 1276 ESDHC_STROBE_DLL_CTRL_SLV_UPDATE_INT_DEFAULT | 1277 (strobe_delay << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT); 1278 writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL); 1279 1280 /* wait max 50us to get the REF/SLV lock */ 1281 ret = readl_poll_timeout(host->ioaddr + ESDHC_STROBE_DLL_STATUS, v, 1282 ((v & ESDHC_STROBE_DLL_STS_REF_LOCK) && (v & ESDHC_STROBE_DLL_STS_SLV_LOCK)), 1, 50); 1283 if (ret == -ETIMEDOUT) 1284 dev_warn(mmc_dev(host->mmc), 1285 "warning! HS400 strobe DLL status REF/SLV not lock in 50us, STROBE DLL status is %x!\n", v); 1286} 1287 1288static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing) 1289{ 1290 u32 m; 1291 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1292 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1293 struct esdhc_platform_data *boarddata = &imx_data->boarddata; 1294 1295 /* disable ddr mode and disable HS400 mode */ 1296 m = readl(host->ioaddr + ESDHC_MIX_CTRL); 1297 m &= ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN); 1298 imx_data->is_ddr = 0; 1299 1300 switch (timing) { 1301 case MMC_TIMING_UHS_SDR12: 1302 case MMC_TIMING_UHS_SDR25: 1303 case MMC_TIMING_UHS_SDR50: 1304 case MMC_TIMING_UHS_SDR104: 1305 case MMC_TIMING_MMC_HS: 1306 case MMC_TIMING_MMC_HS200: 1307 writel(m, host->ioaddr + ESDHC_MIX_CTRL); 1308 break; 1309 case MMC_TIMING_UHS_DDR50: 1310 case MMC_TIMING_MMC_DDR52: 1311 m |= ESDHC_MIX_CTRL_DDREN; 1312 writel(m, host->ioaddr + ESDHC_MIX_CTRL); 1313 imx_data->is_ddr = 1; 1314 if (boarddata->delay_line) { 1315 u32 v; 1316 v = boarddata->delay_line << 1317 ESDHC_DLL_OVERRIDE_VAL_SHIFT | 1318 (1 << ESDHC_DLL_OVERRIDE_EN_SHIFT); 1319 if (is_imx53_esdhc(imx_data)) 1320 v <<= 1; 1321 writel(v, host->ioaddr + ESDHC_DLL_CTRL); 1322 } 1323 break; 1324 case MMC_TIMING_MMC_HS400: 1325 m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN; 1326 writel(m, host->ioaddr + ESDHC_MIX_CTRL); 1327 imx_data->is_ddr = 1; 1328 /* update clock after enable DDR for strobe DLL lock */ 1329 host->ops->set_clock(host, host->clock); 1330 esdhc_set_strobe_dll(host); 1331 break; 1332 case MMC_TIMING_LEGACY: 1333 default: 1334 esdhc_reset_tuning(host); 1335 break; 1336 } 1337 1338 esdhc_change_pinstate(host, timing); 1339} 1340 1341static void esdhc_reset(struct sdhci_host *host, u8 mask) 1342{ 1343 sdhci_and_cqhci_reset(host, mask); 1344 1345 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE); 1346 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE); 1347} 1348 1349static unsigned int esdhc_get_max_timeout_count(struct sdhci_host *host) 1350{ 1351 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1352 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1353 1354 /* Doc Erratum: the uSDHC actual maximum timeout count is 1 << 29 */ 1355 return esdhc_is_usdhc(imx_data) ? 1 << 29 : 1 << 27; 1356} 1357 1358static void esdhc_set_timeout(struct sdhci_host *host, struct mmc_command *cmd) 1359{ 1360 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1361 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1362 1363 /* use maximum timeout counter */ 1364 esdhc_clrset_le(host, ESDHC_SYS_CTRL_DTOCV_MASK, 1365 esdhc_is_usdhc(imx_data) ? 0xF : 0xE, 1366 SDHCI_TIMEOUT_CONTROL); 1367} 1368 1369static u32 esdhc_cqhci_irq(struct sdhci_host *host, u32 intmask) 1370{ 1371 int cmd_error = 0; 1372 int data_error = 0; 1373 1374 if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error)) 1375 return intmask; 1376 1377 cqhci_irq(host->mmc, intmask, cmd_error, data_error); 1378 1379 return 0; 1380} 1381 1382static struct sdhci_ops sdhci_esdhc_ops = { 1383 .read_l = esdhc_readl_le, 1384 .read_w = esdhc_readw_le, 1385 .read_b = esdhc_readb_le, 1386 .write_l = esdhc_writel_le, 1387 .write_w = esdhc_writew_le, 1388 .write_b = esdhc_writeb_le, 1389 .set_clock = esdhc_pltfm_set_clock, 1390 .get_max_clock = esdhc_pltfm_get_max_clock, 1391 .get_min_clock = esdhc_pltfm_get_min_clock, 1392 .get_max_timeout_count = esdhc_get_max_timeout_count, 1393 .get_ro = esdhc_pltfm_get_ro, 1394 .set_timeout = esdhc_set_timeout, 1395 .set_bus_width = esdhc_pltfm_set_bus_width, 1396 .set_uhs_signaling = esdhc_set_uhs_signaling, 1397 .reset = esdhc_reset, 1398 .irq = esdhc_cqhci_irq, 1399 .dump_vendor_regs = esdhc_dump_debug_regs, 1400}; 1401 1402static const struct sdhci_pltfm_data sdhci_esdhc_imx_pdata = { 1403 .quirks = ESDHC_DEFAULT_QUIRKS | SDHCI_QUIRK_NO_HISPD_BIT 1404 | SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC 1405 | SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC 1406 | SDHCI_QUIRK_BROKEN_CARD_DETECTION, 1407 .ops = &sdhci_esdhc_ops, 1408}; 1409 1410static void sdhci_esdhc_imx_hwinit(struct sdhci_host *host) 1411{ 1412 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1413 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1414 struct cqhci_host *cq_host = host->mmc->cqe_private; 1415 u32 tmp; 1416 1417 if (esdhc_is_usdhc(imx_data)) { 1418 /* 1419 * The imx6q ROM code will change the default watermark 1420 * level setting to something insane. Change it back here. 1421 */ 1422 writel(ESDHC_WTMK_DEFAULT_VAL, host->ioaddr + ESDHC_WTMK_LVL); 1423 1424 /* 1425 * ROM code will change the bit burst_length_enable setting 1426 * to zero if this usdhc is chosen to boot system. Change 1427 * it back here, otherwise it will impact the performance a 1428 * lot. This bit is used to enable/disable the burst length 1429 * for the external AHB2AXI bridge. It's useful especially 1430 * for INCR transfer because without burst length indicator, 1431 * the AHB2AXI bridge does not know the burst length in 1432 * advance. And without burst length indicator, AHB INCR 1433 * transfer can only be converted to singles on the AXI side. 1434 */ 1435 writel(readl(host->ioaddr + SDHCI_HOST_CONTROL) 1436 | ESDHC_BURST_LEN_EN_INCR, 1437 host->ioaddr + SDHCI_HOST_CONTROL); 1438 1439 /* 1440 * erratum ESDHC_FLAG_ERR004536 fix for MX6Q TO1.2 and MX6DL 1441 * TO1.1, it's harmless for MX6SL 1442 */ 1443 if (!(imx_data->socdata->flags & ESDHC_FLAG_SKIP_ERR004536)) { 1444 writel(readl(host->ioaddr + 0x6c) & ~BIT(7), 1445 host->ioaddr + 0x6c); 1446 } 1447 1448 /* disable DLL_CTRL delay line settings */ 1449 writel(0x0, host->ioaddr + ESDHC_DLL_CTRL); 1450 1451 /* 1452 * For the case of command with busy, if set the bit 1453 * ESDHC_VEND_SPEC2_EN_BUSY_IRQ, USDHC will generate a 1454 * transfer complete interrupt when busy is deasserted. 1455 * When CQHCI use DCMD to send a CMD need R1b respons, 1456 * CQHCI require to set ESDHC_VEND_SPEC2_EN_BUSY_IRQ, 1457 * otherwise DCMD will always meet timeout waiting for 1458 * hardware interrupt issue. 1459 */ 1460 if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) { 1461 tmp = readl(host->ioaddr + ESDHC_VEND_SPEC2); 1462 tmp |= ESDHC_VEND_SPEC2_EN_BUSY_IRQ; 1463 writel(tmp, host->ioaddr + ESDHC_VEND_SPEC2); 1464 1465 host->quirks &= ~SDHCI_QUIRK_NO_BUSY_IRQ; 1466 } 1467 1468 if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) { 1469 tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL); 1470 tmp |= ESDHC_STD_TUNING_EN; 1471 1472 /* 1473 * ROM code or bootloader may config the start tap 1474 * and step, unmask them first. 1475 */ 1476 tmp &= ~(ESDHC_TUNING_START_TAP_MASK | ESDHC_TUNING_STEP_MASK); 1477 if (imx_data->boarddata.tuning_start_tap) 1478 tmp |= imx_data->boarddata.tuning_start_tap; 1479 else 1480 tmp |= ESDHC_TUNING_START_TAP_DEFAULT; 1481 1482 if (imx_data->boarddata.tuning_step) { 1483 tmp |= imx_data->boarddata.tuning_step 1484 << ESDHC_TUNING_STEP_SHIFT; 1485 } else { 1486 tmp |= ESDHC_TUNING_STEP_DEFAULT 1487 << ESDHC_TUNING_STEP_SHIFT; 1488 } 1489 1490 /* Disable the CMD CRC check for tuning, if not, need to 1491 * add some delay after every tuning command, because 1492 * hardware standard tuning logic will directly go to next 1493 * step once it detect the CMD CRC error, will not wait for 1494 * the card side to finally send out the tuning data, trigger 1495 * the buffer read ready interrupt immediately. If usdhc send 1496 * the next tuning command some eMMC card will stuck, can't 1497 * response, block the tuning procedure or the first command 1498 * after the whole tuning procedure always can't get any response. 1499 */ 1500 tmp |= ESDHC_TUNING_CMD_CRC_CHECK_DISABLE; 1501 writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL); 1502 } else if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) { 1503 /* 1504 * ESDHC_STD_TUNING_EN may be configed in bootloader 1505 * or ROM code, so clear this bit here to make sure 1506 * the manual tuning can work. 1507 */ 1508 tmp = readl(host->ioaddr + ESDHC_TUNING_CTRL); 1509 tmp &= ~ESDHC_STD_TUNING_EN; 1510 writel(tmp, host->ioaddr + ESDHC_TUNING_CTRL); 1511 } 1512 1513 /* 1514 * On i.MX8MM, we are running Dual Linux OS, with 1st Linux using SD Card 1515 * as rootfs storage, 2nd Linux using eMMC as rootfs storage. We let 1516 * the 1st linux configure power/clock for the 2nd Linux. 1517 * 1518 * When the 2nd Linux is booting into rootfs stage, we let the 1st Linux 1519 * to destroy the 2nd linux, then restart the 2nd linux, we met SDHCI dump. 1520 * After we clear the pending interrupt and halt CQCTL, issue gone. 1521 */ 1522 if (cq_host) { 1523 tmp = cqhci_readl(cq_host, CQHCI_IS); 1524 cqhci_writel(cq_host, tmp, CQHCI_IS); 1525 cqhci_writel(cq_host, CQHCI_HALT, CQHCI_CTL); 1526 } 1527 } 1528} 1529 1530static void esdhc_cqe_enable(struct mmc_host *mmc) 1531{ 1532 struct sdhci_host *host = mmc_priv(mmc); 1533 struct cqhci_host *cq_host = mmc->cqe_private; 1534 u32 reg; 1535 u16 mode; 1536 int count = 10; 1537 1538 /* 1539 * CQE gets stuck if it sees Buffer Read Enable bit set, which can be 1540 * the case after tuning, so ensure the buffer is drained. 1541 */ 1542 reg = sdhci_readl(host, SDHCI_PRESENT_STATE); 1543 while (reg & SDHCI_DATA_AVAILABLE) { 1544 sdhci_readl(host, SDHCI_BUFFER); 1545 reg = sdhci_readl(host, SDHCI_PRESENT_STATE); 1546 if (count-- == 0) { 1547 dev_warn(mmc_dev(host->mmc), 1548 "CQE may get stuck because the Buffer Read Enable bit is set\n"); 1549 break; 1550 } 1551 mdelay(1); 1552 } 1553 1554 /* 1555 * Runtime resume will reset the entire host controller, which 1556 * will also clear the DMAEN/BCEN of register ESDHC_MIX_CTRL. 1557 * Here set DMAEN and BCEN when enable CMDQ. 1558 */ 1559 mode = sdhci_readw(host, SDHCI_TRANSFER_MODE); 1560 if (host->flags & SDHCI_REQ_USE_DMA) 1561 mode |= SDHCI_TRNS_DMA; 1562 if (!(host->quirks2 & SDHCI_QUIRK2_SUPPORT_SINGLE)) 1563 mode |= SDHCI_TRNS_BLK_CNT_EN; 1564 sdhci_writew(host, mode, SDHCI_TRANSFER_MODE); 1565 1566 /* 1567 * Though Runtime resume reset the entire host controller, 1568 * but do not impact the CQHCI side, need to clear the 1569 * HALT bit, avoid CQHCI stuck in the first request when 1570 * system resume back. 1571 */ 1572 cqhci_writel(cq_host, 0, CQHCI_CTL); 1573 if (cqhci_readl(cq_host, CQHCI_CTL) & CQHCI_HALT) 1574 dev_err(mmc_dev(host->mmc), 1575 "failed to exit halt state when enable CQE\n"); 1576 1577 1578 sdhci_cqe_enable(mmc); 1579} 1580 1581static void esdhc_sdhci_dumpregs(struct mmc_host *mmc) 1582{ 1583 sdhci_dumpregs(mmc_priv(mmc)); 1584} 1585 1586static const struct cqhci_host_ops esdhc_cqhci_ops = { 1587 .enable = esdhc_cqe_enable, 1588 .disable = sdhci_cqe_disable, 1589 .dumpregs = esdhc_sdhci_dumpregs, 1590}; 1591 1592static int 1593sdhci_esdhc_imx_probe_dt(struct platform_device *pdev, 1594 struct sdhci_host *host, 1595 struct pltfm_imx_data *imx_data) 1596{ 1597 struct device_node *np = pdev->dev.of_node; 1598 struct esdhc_platform_data *boarddata = &imx_data->boarddata; 1599 int ret; 1600 1601 if (of_property_read_bool(np, "fsl,wp-controller")) 1602 boarddata->wp_type = ESDHC_WP_CONTROLLER; 1603 1604 /* 1605 * If we have this property, then activate WP check. 1606 * Retrieveing and requesting the actual WP GPIO will happen 1607 * in the call to mmc_of_parse(). 1608 */ 1609 if (of_property_read_bool(np, "wp-gpios")) 1610 boarddata->wp_type = ESDHC_WP_GPIO; 1611 1612 of_property_read_u32(np, "fsl,tuning-step", &boarddata->tuning_step); 1613 of_property_read_u32(np, "fsl,tuning-start-tap", 1614 &boarddata->tuning_start_tap); 1615 1616 of_property_read_u32(np, "fsl,strobe-dll-delay-target", 1617 &boarddata->strobe_dll_delay_target); 1618 if (of_property_read_bool(np, "no-1-8-v")) 1619 host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V; 1620 1621 if (of_property_read_u32(np, "fsl,delay-line", &boarddata->delay_line)) 1622 boarddata->delay_line = 0; 1623 1624 mmc_of_parse_voltage(host->mmc, &host->ocr_mask); 1625 1626 if (esdhc_is_usdhc(imx_data) && !IS_ERR(imx_data->pinctrl)) { 1627 imx_data->pins_100mhz = pinctrl_lookup_state(imx_data->pinctrl, 1628 ESDHC_PINCTRL_STATE_100MHZ); 1629 imx_data->pins_200mhz = pinctrl_lookup_state(imx_data->pinctrl, 1630 ESDHC_PINCTRL_STATE_200MHZ); 1631 } 1632 1633 /* call to generic mmc_of_parse to support additional capabilities */ 1634 ret = mmc_of_parse(host->mmc); 1635 if (ret) 1636 return ret; 1637 1638 /* HS400/HS400ES require 8 bit bus */ 1639 if (!(host->mmc->caps & MMC_CAP_8_BIT_DATA)) 1640 host->mmc->caps2 &= ~(MMC_CAP2_HS400 | MMC_CAP2_HS400_ES); 1641 1642 if (mmc_gpio_get_cd(host->mmc) >= 0) 1643 host->quirks &= ~SDHCI_QUIRK_BROKEN_CARD_DETECTION; 1644 1645 return 0; 1646} 1647 1648static int sdhci_esdhc_imx_probe(struct platform_device *pdev) 1649{ 1650 struct sdhci_pltfm_host *pltfm_host; 1651 struct sdhci_host *host; 1652 struct cqhci_host *cq_host; 1653 int err; 1654 struct pltfm_imx_data *imx_data; 1655 1656 host = sdhci_pltfm_init(pdev, &sdhci_esdhc_imx_pdata, 1657 sizeof(*imx_data)); 1658 if (IS_ERR(host)) 1659 return PTR_ERR(host); 1660 1661 pltfm_host = sdhci_priv(host); 1662 1663 imx_data = sdhci_pltfm_priv(pltfm_host); 1664 1665 imx_data->socdata = device_get_match_data(&pdev->dev); 1666 1667 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS) 1668 cpu_latency_qos_add_request(&imx_data->pm_qos_req, 0); 1669 1670 imx_data->clk_ipg = devm_clk_get(&pdev->dev, "ipg"); 1671 if (IS_ERR(imx_data->clk_ipg)) { 1672 err = PTR_ERR(imx_data->clk_ipg); 1673 goto free_sdhci; 1674 } 1675 1676 imx_data->clk_ahb = devm_clk_get(&pdev->dev, "ahb"); 1677 if (IS_ERR(imx_data->clk_ahb)) { 1678 err = PTR_ERR(imx_data->clk_ahb); 1679 goto free_sdhci; 1680 } 1681 1682 imx_data->clk_per = devm_clk_get(&pdev->dev, "per"); 1683 if (IS_ERR(imx_data->clk_per)) { 1684 err = PTR_ERR(imx_data->clk_per); 1685 goto free_sdhci; 1686 } 1687 1688 pltfm_host->clk = imx_data->clk_per; 1689 pltfm_host->clock = clk_get_rate(pltfm_host->clk); 1690 err = clk_prepare_enable(imx_data->clk_per); 1691 if (err) 1692 goto free_sdhci; 1693 err = clk_prepare_enable(imx_data->clk_ipg); 1694 if (err) 1695 goto disable_per_clk; 1696 err = clk_prepare_enable(imx_data->clk_ahb); 1697 if (err) 1698 goto disable_ipg_clk; 1699 1700 imx_data->pinctrl = devm_pinctrl_get(&pdev->dev); 1701 if (IS_ERR(imx_data->pinctrl)) 1702 dev_warn(mmc_dev(host->mmc), "could not get pinctrl\n"); 1703 1704 if (esdhc_is_usdhc(imx_data)) { 1705 host->quirks2 |= SDHCI_QUIRK2_PRESET_VALUE_BROKEN; 1706 host->mmc->caps |= MMC_CAP_1_8V_DDR | MMC_CAP_3_3V_DDR; 1707 1708 /* GPIO CD can be set as a wakeup source */ 1709 host->mmc->caps |= MMC_CAP_CD_WAKE; 1710 1711 if (!(imx_data->socdata->flags & ESDHC_FLAG_HS200)) 1712 host->quirks2 |= SDHCI_QUIRK2_BROKEN_HS200; 1713 1714 /* clear tuning bits in case ROM has set it already */ 1715 writel(0x0, host->ioaddr + ESDHC_MIX_CTRL); 1716 writel(0x0, host->ioaddr + SDHCI_AUTO_CMD_STATUS); 1717 writel(0x0, host->ioaddr + ESDHC_TUNE_CTRL_STATUS); 1718 1719 /* 1720 * Link usdhc specific mmc_host_ops execute_tuning function, 1721 * to replace the standard one in sdhci_ops. 1722 */ 1723 host->mmc_host_ops.execute_tuning = usdhc_execute_tuning; 1724 1725 /* 1726 * Link usdhc specific mmc_host_ops init card function, 1727 * to distinguish the card type. 1728 */ 1729 host->mmc_host_ops.init_card = usdhc_init_card; 1730 } 1731 1732 if (imx_data->socdata->flags & ESDHC_FLAG_MAN_TUNING) 1733 sdhci_esdhc_ops.platform_execute_tuning = 1734 esdhc_executing_tuning; 1735 1736 if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536) 1737 host->quirks |= SDHCI_QUIRK_BROKEN_ADMA; 1738 1739 if (imx_data->socdata->flags & ESDHC_FLAG_HS400) 1740 host->mmc->caps2 |= MMC_CAP2_HS400; 1741 1742 if (imx_data->socdata->flags & ESDHC_FLAG_BROKEN_AUTO_CMD23) 1743 host->quirks2 |= SDHCI_QUIRK2_ACMD23_BROKEN; 1744 1745 if (imx_data->socdata->flags & ESDHC_FLAG_HS400_ES) { 1746 host->mmc->caps2 |= MMC_CAP2_HS400_ES; 1747 host->mmc_host_ops.hs400_enhanced_strobe = 1748 esdhc_hs400_enhanced_strobe; 1749 } 1750 1751 if (imx_data->socdata->flags & ESDHC_FLAG_CQHCI) { 1752 host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD; 1753 cq_host = devm_kzalloc(&pdev->dev, sizeof(*cq_host), GFP_KERNEL); 1754 if (!cq_host) { 1755 err = -ENOMEM; 1756 goto disable_ahb_clk; 1757 } 1758 1759 cq_host->mmio = host->ioaddr + ESDHC_CQHCI_ADDR_OFFSET; 1760 cq_host->ops = &esdhc_cqhci_ops; 1761 1762 err = cqhci_init(cq_host, host->mmc, false); 1763 if (err) 1764 goto disable_ahb_clk; 1765 } 1766 1767 err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data); 1768 if (err) 1769 goto disable_ahb_clk; 1770 1771 sdhci_esdhc_imx_hwinit(host); 1772 1773 err = sdhci_add_host(host); 1774 if (err) 1775 goto disable_ahb_clk; 1776 1777 /* 1778 * Setup the wakeup capability here, let user to decide 1779 * whether need to enable this wakeup through sysfs interface. 1780 */ 1781 if ((host->mmc->pm_caps & MMC_PM_KEEP_POWER) && 1782 (host->mmc->pm_caps & MMC_PM_WAKE_SDIO_IRQ)) 1783 device_set_wakeup_capable(&pdev->dev, true); 1784 1785 pm_runtime_set_active(&pdev->dev); 1786 pm_runtime_set_autosuspend_delay(&pdev->dev, 50); 1787 pm_runtime_use_autosuspend(&pdev->dev); 1788 pm_suspend_ignore_children(&pdev->dev, 1); 1789 pm_runtime_enable(&pdev->dev); 1790 1791 return 0; 1792 1793disable_ahb_clk: 1794 clk_disable_unprepare(imx_data->clk_ahb); 1795disable_ipg_clk: 1796 clk_disable_unprepare(imx_data->clk_ipg); 1797disable_per_clk: 1798 clk_disable_unprepare(imx_data->clk_per); 1799free_sdhci: 1800 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS) 1801 cpu_latency_qos_remove_request(&imx_data->pm_qos_req); 1802 sdhci_pltfm_free(pdev); 1803 return err; 1804} 1805 1806static void sdhci_esdhc_imx_remove(struct platform_device *pdev) 1807{ 1808 struct sdhci_host *host = platform_get_drvdata(pdev); 1809 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1810 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1811 int dead; 1812 1813 pm_runtime_get_sync(&pdev->dev); 1814 dead = (readl(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff); 1815 pm_runtime_disable(&pdev->dev); 1816 pm_runtime_put_noidle(&pdev->dev); 1817 1818 sdhci_remove_host(host, dead); 1819 1820 clk_disable_unprepare(imx_data->clk_per); 1821 clk_disable_unprepare(imx_data->clk_ipg); 1822 clk_disable_unprepare(imx_data->clk_ahb); 1823 1824 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS) 1825 cpu_latency_qos_remove_request(&imx_data->pm_qos_req); 1826 1827 sdhci_pltfm_free(pdev); 1828} 1829 1830#ifdef CONFIG_PM_SLEEP 1831static int sdhci_esdhc_suspend(struct device *dev) 1832{ 1833 struct sdhci_host *host = dev_get_drvdata(dev); 1834 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1835 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1836 int ret; 1837 1838 if (host->mmc->caps2 & MMC_CAP2_CQE) { 1839 ret = cqhci_suspend(host->mmc); 1840 if (ret) 1841 return ret; 1842 } 1843 1844 if ((imx_data->socdata->flags & ESDHC_FLAG_STATE_LOST_IN_LPMODE) && 1845 (host->tuning_mode != SDHCI_TUNING_MODE_1)) { 1846 mmc_retune_timer_stop(host->mmc); 1847 mmc_retune_needed(host->mmc); 1848 } 1849 1850 if (host->tuning_mode != SDHCI_TUNING_MODE_3) 1851 mmc_retune_needed(host->mmc); 1852 1853 ret = sdhci_suspend_host(host); 1854 if (ret) 1855 return ret; 1856 1857 ret = pinctrl_pm_select_sleep_state(dev); 1858 if (ret) 1859 return ret; 1860 1861 ret = mmc_gpio_set_cd_wake(host->mmc, true); 1862 1863 return ret; 1864} 1865 1866static int sdhci_esdhc_resume(struct device *dev) 1867{ 1868 struct sdhci_host *host = dev_get_drvdata(dev); 1869 int ret; 1870 1871 ret = pinctrl_pm_select_default_state(dev); 1872 if (ret) 1873 return ret; 1874 1875 /* re-initialize hw state in case it's lost in low power mode */ 1876 sdhci_esdhc_imx_hwinit(host); 1877 1878 ret = sdhci_resume_host(host); 1879 if (ret) 1880 return ret; 1881 1882 if (host->mmc->caps2 & MMC_CAP2_CQE) 1883 ret = cqhci_resume(host->mmc); 1884 1885 if (!ret) 1886 ret = mmc_gpio_set_cd_wake(host->mmc, false); 1887 1888 return ret; 1889} 1890#endif 1891 1892#ifdef CONFIG_PM 1893static int sdhci_esdhc_runtime_suspend(struct device *dev) 1894{ 1895 struct sdhci_host *host = dev_get_drvdata(dev); 1896 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1897 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1898 int ret; 1899 1900 if (host->mmc->caps2 & MMC_CAP2_CQE) { 1901 ret = cqhci_suspend(host->mmc); 1902 if (ret) 1903 return ret; 1904 } 1905 1906 ret = sdhci_runtime_suspend_host(host); 1907 if (ret) 1908 return ret; 1909 1910 if (host->tuning_mode != SDHCI_TUNING_MODE_3) 1911 mmc_retune_needed(host->mmc); 1912 1913 imx_data->actual_clock = host->mmc->actual_clock; 1914 esdhc_pltfm_set_clock(host, 0); 1915 clk_disable_unprepare(imx_data->clk_per); 1916 clk_disable_unprepare(imx_data->clk_ipg); 1917 clk_disable_unprepare(imx_data->clk_ahb); 1918 1919 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS) 1920 cpu_latency_qos_remove_request(&imx_data->pm_qos_req); 1921 1922 return ret; 1923} 1924 1925static int sdhci_esdhc_runtime_resume(struct device *dev) 1926{ 1927 struct sdhci_host *host = dev_get_drvdata(dev); 1928 struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); 1929 struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host); 1930 int err; 1931 1932 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS) 1933 cpu_latency_qos_add_request(&imx_data->pm_qos_req, 0); 1934 1935 if (imx_data->socdata->flags & ESDHC_FLAG_CLK_RATE_LOST_IN_PM_RUNTIME) 1936 clk_set_rate(imx_data->clk_per, pltfm_host->clock); 1937 1938 err = clk_prepare_enable(imx_data->clk_ahb); 1939 if (err) 1940 goto remove_pm_qos_request; 1941 1942 err = clk_prepare_enable(imx_data->clk_per); 1943 if (err) 1944 goto disable_ahb_clk; 1945 1946 err = clk_prepare_enable(imx_data->clk_ipg); 1947 if (err) 1948 goto disable_per_clk; 1949 1950 esdhc_pltfm_set_clock(host, imx_data->actual_clock); 1951 1952 err = sdhci_runtime_resume_host(host, 0); 1953 if (err) 1954 goto disable_ipg_clk; 1955 1956 if (host->mmc->caps2 & MMC_CAP2_CQE) 1957 err = cqhci_resume(host->mmc); 1958 1959 return err; 1960 1961disable_ipg_clk: 1962 clk_disable_unprepare(imx_data->clk_ipg); 1963disable_per_clk: 1964 clk_disable_unprepare(imx_data->clk_per); 1965disable_ahb_clk: 1966 clk_disable_unprepare(imx_data->clk_ahb); 1967remove_pm_qos_request: 1968 if (imx_data->socdata->flags & ESDHC_FLAG_PMQOS) 1969 cpu_latency_qos_remove_request(&imx_data->pm_qos_req); 1970 return err; 1971} 1972#endif 1973 1974static const struct dev_pm_ops sdhci_esdhc_pmops = { 1975 SET_SYSTEM_SLEEP_PM_OPS(sdhci_esdhc_suspend, sdhci_esdhc_resume) 1976 SET_RUNTIME_PM_OPS(sdhci_esdhc_runtime_suspend, 1977 sdhci_esdhc_runtime_resume, NULL) 1978}; 1979 1980static struct platform_driver sdhci_esdhc_imx_driver = { 1981 .driver = { 1982 .name = "sdhci-esdhc-imx", 1983 .probe_type = PROBE_PREFER_ASYNCHRONOUS, 1984 .of_match_table = imx_esdhc_dt_ids, 1985 .pm = &sdhci_esdhc_pmops, 1986 }, 1987 .probe = sdhci_esdhc_imx_probe, 1988 .remove_new = sdhci_esdhc_imx_remove, 1989}; 1990 1991module_platform_driver(sdhci_esdhc_imx_driver); 1992 1993MODULE_DESCRIPTION("SDHCI driver for Freescale i.MX eSDHC"); 1994MODULE_AUTHOR("Wolfram Sang <kernel@pengutronix.de>"); 1995MODULE_LICENSE("GPL v2"); 1996