1// SPDX-License-Identifier: GPL-2.0-or-later 2/* 3 * ADXRS290 SPI Gyroscope Driver 4 * 5 * Copyright (C) 2020 Nishant Malpani <nish.malpani25@gmail.com> 6 * Copyright (C) 2020 Analog Devices, Inc. 7 */ 8 9#include <linux/bitfield.h> 10#include <linux/bitops.h> 11#include <linux/delay.h> 12#include <linux/device.h> 13#include <linux/kernel.h> 14#include <linux/module.h> 15#include <linux/spi/spi.h> 16 17#include <linux/iio/buffer.h> 18#include <linux/iio/iio.h> 19#include <linux/iio/sysfs.h> 20#include <linux/iio/trigger.h> 21#include <linux/iio/triggered_buffer.h> 22#include <linux/iio/trigger_consumer.h> 23 24#define ADXRS290_ADI_ID 0xAD 25#define ADXRS290_MEMS_ID 0x1D 26#define ADXRS290_DEV_ID 0x92 27 28#define ADXRS290_REG_ADI_ID 0x00 29#define ADXRS290_REG_MEMS_ID 0x01 30#define ADXRS290_REG_DEV_ID 0x02 31#define ADXRS290_REG_REV_ID 0x03 32#define ADXRS290_REG_SN0 0x04 /* Serial Number Registers, 4 bytes */ 33#define ADXRS290_REG_DATAX0 0x08 /* Roll Rate o/p Data Regs, 2 bytes */ 34#define ADXRS290_REG_DATAY0 0x0A /* Pitch Rate o/p Data Regs, 2 bytes */ 35#define ADXRS290_REG_TEMP0 0x0C 36#define ADXRS290_REG_POWER_CTL 0x10 37#define ADXRS290_REG_FILTER 0x11 38#define ADXRS290_REG_DATA_RDY 0x12 39 40#define ADXRS290_READ BIT(7) 41#define ADXRS290_TSM BIT(0) 42#define ADXRS290_MEASUREMENT BIT(1) 43#define ADXRS290_DATA_RDY_OUT BIT(0) 44#define ADXRS290_SYNC_MASK GENMASK(1, 0) 45#define ADXRS290_SYNC(x) FIELD_PREP(ADXRS290_SYNC_MASK, x) 46#define ADXRS290_LPF_MASK GENMASK(2, 0) 47#define ADXRS290_LPF(x) FIELD_PREP(ADXRS290_LPF_MASK, x) 48#define ADXRS290_HPF_MASK GENMASK(7, 4) 49#define ADXRS290_HPF(x) FIELD_PREP(ADXRS290_HPF_MASK, x) 50 51#define ADXRS290_READ_REG(reg) (ADXRS290_READ | (reg)) 52 53#define ADXRS290_MAX_TRANSITION_TIME_MS 100 54 55enum adxrs290_mode { 56 ADXRS290_MODE_STANDBY, 57 ADXRS290_MODE_MEASUREMENT, 58}; 59 60enum adxrs290_scan_index { 61 ADXRS290_IDX_X, 62 ADXRS290_IDX_Y, 63 ADXRS290_IDX_TEMP, 64 ADXRS290_IDX_TS, 65}; 66 67struct adxrs290_state { 68 struct spi_device *spi; 69 /* Serialize reads and their subsequent processing */ 70 struct mutex lock; 71 enum adxrs290_mode mode; 72 unsigned int lpf_3db_freq_idx; 73 unsigned int hpf_3db_freq_idx; 74 struct iio_trigger *dready_trig; 75 /* Ensure correct alignment of timestamp when present */ 76 struct { 77 s16 channels[3]; 78 s64 ts __aligned(8); 79 } buffer; 80}; 81 82/* 83 * Available cut-off frequencies of the low pass filter in Hz. 84 * The integer part and fractional part are represented separately. 85 */ 86static const int adxrs290_lpf_3db_freq_hz_table[][2] = { 87 [0] = {480, 0}, 88 [1] = {320, 0}, 89 [2] = {160, 0}, 90 [3] = {80, 0}, 91 [4] = {56, 600000}, 92 [5] = {40, 0}, 93 [6] = {28, 300000}, 94 [7] = {20, 0}, 95}; 96 97/* 98 * Available cut-off frequencies of the high pass filter in Hz. 99 * The integer part and fractional part are represented separately. 100 */ 101static const int adxrs290_hpf_3db_freq_hz_table[][2] = { 102 [0] = {0, 0}, 103 [1] = {0, 11000}, 104 [2] = {0, 22000}, 105 [3] = {0, 44000}, 106 [4] = {0, 87000}, 107 [5] = {0, 175000}, 108 [6] = {0, 350000}, 109 [7] = {0, 700000}, 110 [8] = {1, 400000}, 111 [9] = {2, 800000}, 112 [10] = {11, 300000}, 113}; 114 115static int adxrs290_get_rate_data(struct iio_dev *indio_dev, const u8 cmd, int *val) 116{ 117 struct adxrs290_state *st = iio_priv(indio_dev); 118 int ret = 0; 119 int temp; 120 121 mutex_lock(&st->lock); 122 temp = spi_w8r16(st->spi, cmd); 123 if (temp < 0) { 124 ret = temp; 125 goto err_unlock; 126 } 127 128 *val = sign_extend32(temp, 15); 129 130err_unlock: 131 mutex_unlock(&st->lock); 132 return ret; 133} 134 135static int adxrs290_get_temp_data(struct iio_dev *indio_dev, int *val) 136{ 137 const u8 cmd = ADXRS290_READ_REG(ADXRS290_REG_TEMP0); 138 struct adxrs290_state *st = iio_priv(indio_dev); 139 int ret = 0; 140 int temp; 141 142 mutex_lock(&st->lock); 143 temp = spi_w8r16(st->spi, cmd); 144 if (temp < 0) { 145 ret = temp; 146 goto err_unlock; 147 } 148 149 /* extract lower 12 bits temperature reading */ 150 *val = sign_extend32(temp, 11); 151 152err_unlock: 153 mutex_unlock(&st->lock); 154 return ret; 155} 156 157static int adxrs290_get_3db_freq(struct iio_dev *indio_dev, u8 *val, u8 *val2) 158{ 159 const u8 cmd = ADXRS290_READ_REG(ADXRS290_REG_FILTER); 160 struct adxrs290_state *st = iio_priv(indio_dev); 161 int ret = 0; 162 short temp; 163 164 mutex_lock(&st->lock); 165 temp = spi_w8r8(st->spi, cmd); 166 if (temp < 0) { 167 ret = temp; 168 goto err_unlock; 169 } 170 171 *val = FIELD_GET(ADXRS290_LPF_MASK, temp); 172 *val2 = FIELD_GET(ADXRS290_HPF_MASK, temp); 173 174err_unlock: 175 mutex_unlock(&st->lock); 176 return ret; 177} 178 179static int adxrs290_spi_write_reg(struct spi_device *spi, const u8 reg, 180 const u8 val) 181{ 182 u8 buf[2]; 183 184 buf[0] = reg; 185 buf[1] = val; 186 187 return spi_write_then_read(spi, buf, ARRAY_SIZE(buf), NULL, 0); 188} 189 190static int adxrs290_find_match(const int (*freq_tbl)[2], const int n, 191 const int val, const int val2) 192{ 193 int i; 194 195 for (i = 0; i < n; i++) { 196 if (freq_tbl[i][0] == val && freq_tbl[i][1] == val2) 197 return i; 198 } 199 200 return -EINVAL; 201} 202 203static int adxrs290_set_filter_freq(struct iio_dev *indio_dev, 204 const unsigned int lpf_idx, 205 const unsigned int hpf_idx) 206{ 207 struct adxrs290_state *st = iio_priv(indio_dev); 208 u8 val; 209 210 val = ADXRS290_HPF(hpf_idx) | ADXRS290_LPF(lpf_idx); 211 212 return adxrs290_spi_write_reg(st->spi, ADXRS290_REG_FILTER, val); 213} 214 215static int adxrs290_set_mode(struct iio_dev *indio_dev, enum adxrs290_mode mode) 216{ 217 struct adxrs290_state *st = iio_priv(indio_dev); 218 int val, ret; 219 220 if (st->mode == mode) 221 return 0; 222 223 mutex_lock(&st->lock); 224 225 ret = spi_w8r8(st->spi, ADXRS290_READ_REG(ADXRS290_REG_POWER_CTL)); 226 if (ret < 0) 227 goto out_unlock; 228 229 val = ret; 230 231 switch (mode) { 232 case ADXRS290_MODE_STANDBY: 233 val &= ~ADXRS290_MEASUREMENT; 234 break; 235 case ADXRS290_MODE_MEASUREMENT: 236 val |= ADXRS290_MEASUREMENT; 237 break; 238 default: 239 ret = -EINVAL; 240 goto out_unlock; 241 } 242 243 ret = adxrs290_spi_write_reg(st->spi, ADXRS290_REG_POWER_CTL, val); 244 if (ret < 0) { 245 dev_err(&st->spi->dev, "unable to set mode: %d\n", ret); 246 goto out_unlock; 247 } 248 249 /* update cached mode */ 250 st->mode = mode; 251 252out_unlock: 253 mutex_unlock(&st->lock); 254 return ret; 255} 256 257static void adxrs290_chip_off_action(void *data) 258{ 259 struct iio_dev *indio_dev = data; 260 261 adxrs290_set_mode(indio_dev, ADXRS290_MODE_STANDBY); 262} 263 264static int adxrs290_initial_setup(struct iio_dev *indio_dev) 265{ 266 struct adxrs290_state *st = iio_priv(indio_dev); 267 struct spi_device *spi = st->spi; 268 int ret; 269 270 ret = adxrs290_spi_write_reg(spi, ADXRS290_REG_POWER_CTL, 271 ADXRS290_MEASUREMENT | ADXRS290_TSM); 272 if (ret < 0) 273 return ret; 274 275 st->mode = ADXRS290_MODE_MEASUREMENT; 276 277 return devm_add_action_or_reset(&spi->dev, adxrs290_chip_off_action, 278 indio_dev); 279} 280 281static int adxrs290_read_raw(struct iio_dev *indio_dev, 282 struct iio_chan_spec const *chan, 283 int *val, 284 int *val2, 285 long mask) 286{ 287 struct adxrs290_state *st = iio_priv(indio_dev); 288 unsigned int t; 289 int ret; 290 291 switch (mask) { 292 case IIO_CHAN_INFO_RAW: 293 ret = iio_device_claim_direct_mode(indio_dev); 294 if (ret) 295 return ret; 296 297 switch (chan->type) { 298 case IIO_ANGL_VEL: 299 ret = adxrs290_get_rate_data(indio_dev, 300 ADXRS290_READ_REG(chan->address), 301 val); 302 if (ret < 0) 303 break; 304 305 ret = IIO_VAL_INT; 306 break; 307 case IIO_TEMP: 308 ret = adxrs290_get_temp_data(indio_dev, val); 309 if (ret < 0) 310 break; 311 312 ret = IIO_VAL_INT; 313 break; 314 default: 315 ret = -EINVAL; 316 break; 317 } 318 319 iio_device_release_direct_mode(indio_dev); 320 return ret; 321 case IIO_CHAN_INFO_SCALE: 322 switch (chan->type) { 323 case IIO_ANGL_VEL: 324 /* 1 LSB = 0.005 degrees/sec */ 325 *val = 0; 326 *val2 = 87266; 327 return IIO_VAL_INT_PLUS_NANO; 328 case IIO_TEMP: 329 /* 1 LSB = 0.1 degrees Celsius */ 330 *val = 100; 331 return IIO_VAL_INT; 332 default: 333 return -EINVAL; 334 } 335 case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: 336 switch (chan->type) { 337 case IIO_ANGL_VEL: 338 t = st->lpf_3db_freq_idx; 339 *val = adxrs290_lpf_3db_freq_hz_table[t][0]; 340 *val2 = adxrs290_lpf_3db_freq_hz_table[t][1]; 341 return IIO_VAL_INT_PLUS_MICRO; 342 default: 343 return -EINVAL; 344 } 345 case IIO_CHAN_INFO_HIGH_PASS_FILTER_3DB_FREQUENCY: 346 switch (chan->type) { 347 case IIO_ANGL_VEL: 348 t = st->hpf_3db_freq_idx; 349 *val = adxrs290_hpf_3db_freq_hz_table[t][0]; 350 *val2 = adxrs290_hpf_3db_freq_hz_table[t][1]; 351 return IIO_VAL_INT_PLUS_MICRO; 352 default: 353 return -EINVAL; 354 } 355 } 356 357 return -EINVAL; 358} 359 360static int adxrs290_write_raw(struct iio_dev *indio_dev, 361 struct iio_chan_spec const *chan, 362 int val, 363 int val2, 364 long mask) 365{ 366 struct adxrs290_state *st = iio_priv(indio_dev); 367 int ret, lpf_idx, hpf_idx; 368 369 ret = iio_device_claim_direct_mode(indio_dev); 370 if (ret) 371 return ret; 372 373 switch (mask) { 374 case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: 375 lpf_idx = adxrs290_find_match(adxrs290_lpf_3db_freq_hz_table, 376 ARRAY_SIZE(adxrs290_lpf_3db_freq_hz_table), 377 val, val2); 378 if (lpf_idx < 0) { 379 ret = -EINVAL; 380 break; 381 } 382 383 /* caching the updated state of the low-pass filter */ 384 st->lpf_3db_freq_idx = lpf_idx; 385 /* retrieving the current state of the high-pass filter */ 386 hpf_idx = st->hpf_3db_freq_idx; 387 ret = adxrs290_set_filter_freq(indio_dev, lpf_idx, hpf_idx); 388 break; 389 390 case IIO_CHAN_INFO_HIGH_PASS_FILTER_3DB_FREQUENCY: 391 hpf_idx = adxrs290_find_match(adxrs290_hpf_3db_freq_hz_table, 392 ARRAY_SIZE(adxrs290_hpf_3db_freq_hz_table), 393 val, val2); 394 if (hpf_idx < 0) { 395 ret = -EINVAL; 396 break; 397 } 398 399 /* caching the updated state of the high-pass filter */ 400 st->hpf_3db_freq_idx = hpf_idx; 401 /* retrieving the current state of the low-pass filter */ 402 lpf_idx = st->lpf_3db_freq_idx; 403 ret = adxrs290_set_filter_freq(indio_dev, lpf_idx, hpf_idx); 404 break; 405 406 default: 407 ret = -EINVAL; 408 break; 409 } 410 411 iio_device_release_direct_mode(indio_dev); 412 return ret; 413} 414 415static int adxrs290_read_avail(struct iio_dev *indio_dev, 416 struct iio_chan_spec const *chan, 417 const int **vals, int *type, int *length, 418 long mask) 419{ 420 switch (mask) { 421 case IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY: 422 *vals = (const int *)adxrs290_lpf_3db_freq_hz_table; 423 *type = IIO_VAL_INT_PLUS_MICRO; 424 /* Values are stored in a 2D matrix */ 425 *length = ARRAY_SIZE(adxrs290_lpf_3db_freq_hz_table) * 2; 426 427 return IIO_AVAIL_LIST; 428 case IIO_CHAN_INFO_HIGH_PASS_FILTER_3DB_FREQUENCY: 429 *vals = (const int *)adxrs290_hpf_3db_freq_hz_table; 430 *type = IIO_VAL_INT_PLUS_MICRO; 431 /* Values are stored in a 2D matrix */ 432 *length = ARRAY_SIZE(adxrs290_hpf_3db_freq_hz_table) * 2; 433 434 return IIO_AVAIL_LIST; 435 default: 436 return -EINVAL; 437 } 438} 439 440static int adxrs290_reg_access_rw(struct spi_device *spi, unsigned int reg, 441 unsigned int *readval) 442{ 443 int ret; 444 445 ret = spi_w8r8(spi, ADXRS290_READ_REG(reg)); 446 if (ret < 0) 447 return ret; 448 449 *readval = ret; 450 451 return 0; 452} 453 454static int adxrs290_reg_access(struct iio_dev *indio_dev, unsigned int reg, 455 unsigned int writeval, unsigned int *readval) 456{ 457 struct adxrs290_state *st = iio_priv(indio_dev); 458 459 if (readval) 460 return adxrs290_reg_access_rw(st->spi, reg, readval); 461 else 462 return adxrs290_spi_write_reg(st->spi, reg, writeval); 463} 464 465static int adxrs290_data_rdy_trigger_set_state(struct iio_trigger *trig, 466 bool state) 467{ 468 struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); 469 struct adxrs290_state *st = iio_priv(indio_dev); 470 int ret; 471 u8 val; 472 473 val = state ? ADXRS290_SYNC(ADXRS290_DATA_RDY_OUT) : 0; 474 475 ret = adxrs290_spi_write_reg(st->spi, ADXRS290_REG_DATA_RDY, val); 476 if (ret < 0) 477 dev_err(&st->spi->dev, "failed to start data rdy interrupt\n"); 478 479 return ret; 480} 481 482static void adxrs290_reset_trig(struct iio_trigger *trig) 483{ 484 struct iio_dev *indio_dev = iio_trigger_get_drvdata(trig); 485 int val; 486 487 /* 488 * Data ready interrupt is reset after a read of the data registers. 489 * Here, we only read the 16b DATAY registers as that marks the end of 490 * a read of the data registers and initiates a reset for the interrupt 491 * line. 492 */ 493 adxrs290_get_rate_data(indio_dev, 494 ADXRS290_READ_REG(ADXRS290_REG_DATAY0), &val); 495} 496 497static const struct iio_trigger_ops adxrs290_trigger_ops = { 498 .set_trigger_state = &adxrs290_data_rdy_trigger_set_state, 499 .validate_device = &iio_trigger_validate_own_device, 500 .reenable = &adxrs290_reset_trig, 501}; 502 503static irqreturn_t adxrs290_trigger_handler(int irq, void *p) 504{ 505 struct iio_poll_func *pf = p; 506 struct iio_dev *indio_dev = pf->indio_dev; 507 struct adxrs290_state *st = iio_priv(indio_dev); 508 u8 tx = ADXRS290_READ_REG(ADXRS290_REG_DATAX0); 509 int ret; 510 511 mutex_lock(&st->lock); 512 513 /* exercise a bulk data capture starting from reg DATAX0... */ 514 ret = spi_write_then_read(st->spi, &tx, sizeof(tx), st->buffer.channels, 515 sizeof(st->buffer.channels)); 516 if (ret < 0) 517 goto out_unlock_notify; 518 519 iio_push_to_buffers_with_timestamp(indio_dev, &st->buffer, 520 pf->timestamp); 521 522out_unlock_notify: 523 mutex_unlock(&st->lock); 524 iio_trigger_notify_done(indio_dev->trig); 525 526 return IRQ_HANDLED; 527} 528 529#define ADXRS290_ANGL_VEL_CHANNEL(reg, axis) { \ 530 .type = IIO_ANGL_VEL, \ 531 .address = reg, \ 532 .modified = 1, \ 533 .channel2 = IIO_MOD_##axis, \ 534 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \ 535 .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) | \ 536 BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY) | \ 537 BIT(IIO_CHAN_INFO_HIGH_PASS_FILTER_3DB_FREQUENCY), \ 538 .info_mask_shared_by_type_available = \ 539 BIT(IIO_CHAN_INFO_LOW_PASS_FILTER_3DB_FREQUENCY) | \ 540 BIT(IIO_CHAN_INFO_HIGH_PASS_FILTER_3DB_FREQUENCY), \ 541 .scan_index = ADXRS290_IDX_##axis, \ 542 .scan_type = { \ 543 .sign = 's', \ 544 .realbits = 16, \ 545 .storagebits = 16, \ 546 .endianness = IIO_LE, \ 547 }, \ 548} 549 550static const struct iio_chan_spec adxrs290_channels[] = { 551 ADXRS290_ANGL_VEL_CHANNEL(ADXRS290_REG_DATAX0, X), 552 ADXRS290_ANGL_VEL_CHANNEL(ADXRS290_REG_DATAY0, Y), 553 { 554 .type = IIO_TEMP, 555 .address = ADXRS290_REG_TEMP0, 556 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | 557 BIT(IIO_CHAN_INFO_SCALE), 558 .scan_index = ADXRS290_IDX_TEMP, 559 .scan_type = { 560 .sign = 's', 561 .realbits = 12, 562 .storagebits = 16, 563 .endianness = IIO_LE, 564 }, 565 }, 566 IIO_CHAN_SOFT_TIMESTAMP(ADXRS290_IDX_TS), 567}; 568 569static const unsigned long adxrs290_avail_scan_masks[] = { 570 BIT(ADXRS290_IDX_X) | BIT(ADXRS290_IDX_Y) | BIT(ADXRS290_IDX_TEMP), 571 0 572}; 573 574static const struct iio_info adxrs290_info = { 575 .read_raw = &adxrs290_read_raw, 576 .write_raw = &adxrs290_write_raw, 577 .read_avail = &adxrs290_read_avail, 578 .debugfs_reg_access = &adxrs290_reg_access, 579}; 580 581static int adxrs290_probe_trigger(struct iio_dev *indio_dev) 582{ 583 struct adxrs290_state *st = iio_priv(indio_dev); 584 int ret; 585 586 if (!st->spi->irq) { 587 dev_info(&st->spi->dev, "no irq, using polling\n"); 588 return 0; 589 } 590 591 st->dready_trig = devm_iio_trigger_alloc(&st->spi->dev, "%s-dev%d", 592 indio_dev->name, 593 iio_device_id(indio_dev)); 594 if (!st->dready_trig) 595 return -ENOMEM; 596 597 st->dready_trig->ops = &adxrs290_trigger_ops; 598 iio_trigger_set_drvdata(st->dready_trig, indio_dev); 599 600 ret = devm_request_irq(&st->spi->dev, st->spi->irq, 601 &iio_trigger_generic_data_rdy_poll, 602 IRQF_ONESHOT, "adxrs290_irq", st->dready_trig); 603 if (ret < 0) 604 return dev_err_probe(&st->spi->dev, ret, 605 "request irq %d failed\n", st->spi->irq); 606 607 ret = devm_iio_trigger_register(&st->spi->dev, st->dready_trig); 608 if (ret) { 609 dev_err(&st->spi->dev, "iio trigger register failed\n"); 610 return ret; 611 } 612 613 indio_dev->trig = iio_trigger_get(st->dready_trig); 614 615 return 0; 616} 617 618static int adxrs290_probe(struct spi_device *spi) 619{ 620 struct iio_dev *indio_dev; 621 struct adxrs290_state *st; 622 u8 val, val2; 623 int ret; 624 625 indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); 626 if (!indio_dev) 627 return -ENOMEM; 628 629 st = iio_priv(indio_dev); 630 st->spi = spi; 631 632 indio_dev->name = "adxrs290"; 633 indio_dev->modes = INDIO_DIRECT_MODE; 634 indio_dev->channels = adxrs290_channels; 635 indio_dev->num_channels = ARRAY_SIZE(adxrs290_channels); 636 indio_dev->info = &adxrs290_info; 637 indio_dev->available_scan_masks = adxrs290_avail_scan_masks; 638 639 mutex_init(&st->lock); 640 641 val = spi_w8r8(spi, ADXRS290_READ_REG(ADXRS290_REG_ADI_ID)); 642 if (val != ADXRS290_ADI_ID) { 643 dev_err(&spi->dev, "Wrong ADI ID 0x%02x\n", val); 644 return -ENODEV; 645 } 646 647 val = spi_w8r8(spi, ADXRS290_READ_REG(ADXRS290_REG_MEMS_ID)); 648 if (val != ADXRS290_MEMS_ID) { 649 dev_err(&spi->dev, "Wrong MEMS ID 0x%02x\n", val); 650 return -ENODEV; 651 } 652 653 val = spi_w8r8(spi, ADXRS290_READ_REG(ADXRS290_REG_DEV_ID)); 654 if (val != ADXRS290_DEV_ID) { 655 dev_err(&spi->dev, "Wrong DEV ID 0x%02x\n", val); 656 return -ENODEV; 657 } 658 659 /* default mode the gyroscope starts in */ 660 st->mode = ADXRS290_MODE_STANDBY; 661 662 /* switch to measurement mode and switch on the temperature sensor */ 663 ret = adxrs290_initial_setup(indio_dev); 664 if (ret < 0) 665 return ret; 666 667 /* max transition time to measurement mode */ 668 msleep(ADXRS290_MAX_TRANSITION_TIME_MS); 669 670 ret = adxrs290_get_3db_freq(indio_dev, &val, &val2); 671 if (ret < 0) 672 return ret; 673 674 st->lpf_3db_freq_idx = val; 675 st->hpf_3db_freq_idx = val2; 676 677 ret = devm_iio_triggered_buffer_setup(&spi->dev, indio_dev, 678 &iio_pollfunc_store_time, 679 &adxrs290_trigger_handler, NULL); 680 if (ret < 0) 681 return dev_err_probe(&spi->dev, ret, 682 "iio triggered buffer setup failed\n"); 683 684 ret = adxrs290_probe_trigger(indio_dev); 685 if (ret < 0) 686 return ret; 687 688 return devm_iio_device_register(&spi->dev, indio_dev); 689} 690 691static const struct of_device_id adxrs290_of_match[] = { 692 { .compatible = "adi,adxrs290" }, 693 { } 694}; 695MODULE_DEVICE_TABLE(of, adxrs290_of_match); 696 697static struct spi_driver adxrs290_driver = { 698 .driver = { 699 .name = "adxrs290", 700 .of_match_table = adxrs290_of_match, 701 }, 702 .probe = adxrs290_probe, 703}; 704module_spi_driver(adxrs290_driver); 705 706MODULE_AUTHOR("Nishant Malpani <nish.malpani25@gmail.com>"); 707MODULE_DESCRIPTION("Analog Devices ADXRS290 Gyroscope SPI driver"); 708MODULE_LICENSE("GPL"); 709