1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * linux/arch/arm/common/locomo.c 4 * 5 * Sharp LoCoMo support 6 * 7 * This file contains all generic LoCoMo support. 8 * 9 * All initialization functions provided here are intended to be called 10 * from machine specific code with proper arguments when required. 11 * 12 * Based on sa1111.c 13 */ 14 15#include <linux/module.h> 16#include <linux/init.h> 17#include <linux/kernel.h> 18#include <linux/delay.h> 19#include <linux/errno.h> 20#include <linux/ioport.h> 21#include <linux/platform_device.h> 22#include <linux/slab.h> 23#include <linux/spinlock.h> 24#include <linux/io.h> 25 26#include <asm/irq.h> 27#include <asm/mach/irq.h> 28 29#include <asm/hardware/locomo.h> 30 31/* LoCoMo Interrupts */ 32#define IRQ_LOCOMO_KEY (0) 33#define IRQ_LOCOMO_GPIO (1) 34#define IRQ_LOCOMO_LT (2) 35#define IRQ_LOCOMO_SPI (3) 36 37/* M62332 output channel selection */ 38#define M62332_EVR_CH 1 /* M62332 volume channel number */ 39 /* 0 : CH.1 , 1 : CH. 2 */ 40/* DAC send data */ 41#define M62332_SLAVE_ADDR 0x4e /* Slave address */ 42#define M62332_W_BIT 0x00 /* W bit (0 only) */ 43#define M62332_SUB_ADDR 0x00 /* Sub address */ 44#define M62332_A_BIT 0x00 /* A bit (0 only) */ 45 46/* DAC setup and hold times (expressed in us) */ 47#define DAC_BUS_FREE_TIME 5 /* 4.7 us */ 48#define DAC_START_SETUP_TIME 5 /* 4.7 us */ 49#define DAC_STOP_SETUP_TIME 4 /* 4.0 us */ 50#define DAC_START_HOLD_TIME 5 /* 4.7 us */ 51#define DAC_SCL_LOW_HOLD_TIME 5 /* 4.7 us */ 52#define DAC_SCL_HIGH_HOLD_TIME 4 /* 4.0 us */ 53#define DAC_DATA_SETUP_TIME 1 /* 250 ns */ 54#define DAC_DATA_HOLD_TIME 1 /* 300 ns */ 55#define DAC_LOW_SETUP_TIME 1 /* 300 ns */ 56#define DAC_HIGH_SETUP_TIME 1 /* 1000 ns */ 57 58/* the following is the overall data for the locomo chip */ 59struct locomo { 60 struct device *dev; 61 unsigned long phys; 62 unsigned int irq; 63 int irq_base; 64 spinlock_t lock; 65 void __iomem *base; 66#ifdef CONFIG_PM 67 void *saved_state; 68#endif 69}; 70 71struct locomo_dev_info { 72 unsigned long offset; 73 unsigned long length; 74 unsigned int devid; 75 unsigned int irq[1]; 76 const char * name; 77}; 78 79/* All the locomo devices. If offset is non-zero, the mapbase for the 80 * locomo_dev will be set to the chip base plus offset. If offset is 81 * zero, then the mapbase for the locomo_dev will be set to zero. An 82 * offset of zero means the device only uses GPIOs or other helper 83 * functions inside this file */ 84static struct locomo_dev_info locomo_devices[] = { 85 { 86 .devid = LOCOMO_DEVID_KEYBOARD, 87 .irq = { IRQ_LOCOMO_KEY }, 88 .name = "locomo-keyboard", 89 .offset = LOCOMO_KEYBOARD, 90 .length = 16, 91 }, 92 { 93 .devid = LOCOMO_DEVID_FRONTLIGHT, 94 .irq = {}, 95 .name = "locomo-frontlight", 96 .offset = LOCOMO_FRONTLIGHT, 97 .length = 8, 98 99 }, 100 { 101 .devid = LOCOMO_DEVID_BACKLIGHT, 102 .irq = {}, 103 .name = "locomo-backlight", 104 .offset = LOCOMO_BACKLIGHT, 105 .length = 8, 106 }, 107 { 108 .devid = LOCOMO_DEVID_AUDIO, 109 .irq = {}, 110 .name = "locomo-audio", 111 .offset = LOCOMO_AUDIO, 112 .length = 4, 113 }, 114 { 115 .devid = LOCOMO_DEVID_LED, 116 .irq = {}, 117 .name = "locomo-led", 118 .offset = LOCOMO_LED, 119 .length = 8, 120 }, 121 { 122 .devid = LOCOMO_DEVID_UART, 123 .irq = {}, 124 .name = "locomo-uart", 125 .offset = 0, 126 .length = 0, 127 }, 128 { 129 .devid = LOCOMO_DEVID_SPI, 130 .irq = {}, 131 .name = "locomo-spi", 132 .offset = LOCOMO_SPI, 133 .length = 0x30, 134 }, 135}; 136 137static void locomo_handler(struct irq_desc *desc) 138{ 139 struct locomo *lchip = irq_desc_get_handler_data(desc); 140 int req, i; 141 142 /* Acknowledge the parent IRQ */ 143 desc->irq_data.chip->irq_ack(&desc->irq_data); 144 145 /* check why this interrupt was generated */ 146 req = locomo_readl(lchip->base + LOCOMO_ICR) & 0x0f00; 147 148 if (req) { 149 unsigned int irq; 150 151 /* generate the next interrupt(s) */ 152 irq = lchip->irq_base; 153 for (i = 0; i <= 3; i++, irq++) { 154 if (req & (0x0100 << i)) { 155 generic_handle_irq(irq); 156 } 157 158 } 159 } 160} 161 162static void locomo_ack_irq(struct irq_data *d) 163{ 164} 165 166static void locomo_mask_irq(struct irq_data *d) 167{ 168 struct locomo *lchip = irq_data_get_irq_chip_data(d); 169 unsigned int r; 170 r = locomo_readl(lchip->base + LOCOMO_ICR); 171 r &= ~(0x0010 << (d->irq - lchip->irq_base)); 172 locomo_writel(r, lchip->base + LOCOMO_ICR); 173} 174 175static void locomo_unmask_irq(struct irq_data *d) 176{ 177 struct locomo *lchip = irq_data_get_irq_chip_data(d); 178 unsigned int r; 179 r = locomo_readl(lchip->base + LOCOMO_ICR); 180 r |= (0x0010 << (d->irq - lchip->irq_base)); 181 locomo_writel(r, lchip->base + LOCOMO_ICR); 182} 183 184static struct irq_chip locomo_chip = { 185 .name = "LOCOMO", 186 .irq_ack = locomo_ack_irq, 187 .irq_mask = locomo_mask_irq, 188 .irq_unmask = locomo_unmask_irq, 189}; 190 191static void locomo_setup_irq(struct locomo *lchip) 192{ 193 int irq = lchip->irq_base; 194 195 /* 196 * Install handler for IRQ_LOCOMO_HW. 197 */ 198 irq_set_irq_type(lchip->irq, IRQ_TYPE_EDGE_FALLING); 199 irq_set_chained_handler_and_data(lchip->irq, locomo_handler, lchip); 200 201 /* Install handlers for IRQ_LOCOMO_* */ 202 for ( ; irq <= lchip->irq_base + 3; irq++) { 203 irq_set_chip_and_handler(irq, &locomo_chip, handle_level_irq); 204 irq_set_chip_data(irq, lchip); 205 irq_clear_status_flags(irq, IRQ_NOREQUEST | IRQ_NOPROBE); 206 } 207} 208 209 210static void locomo_dev_release(struct device *_dev) 211{ 212 struct locomo_dev *dev = LOCOMO_DEV(_dev); 213 214 kfree(dev); 215} 216 217static int 218locomo_init_one_child(struct locomo *lchip, struct locomo_dev_info *info) 219{ 220 struct locomo_dev *dev; 221 int ret; 222 223 dev = kzalloc(sizeof(struct locomo_dev), GFP_KERNEL); 224 if (!dev) { 225 ret = -ENOMEM; 226 goto out; 227 } 228 229 /* 230 * If the parent device has a DMA mask associated with it, 231 * propagate it down to the children. 232 */ 233 if (lchip->dev->dma_mask) { 234 dev->dma_mask = *lchip->dev->dma_mask; 235 dev->dev.dma_mask = &dev->dma_mask; 236 } 237 238 dev_set_name(&dev->dev, "%s", info->name); 239 dev->devid = info->devid; 240 dev->dev.parent = lchip->dev; 241 dev->dev.bus = &locomo_bus_type; 242 dev->dev.release = locomo_dev_release; 243 dev->dev.coherent_dma_mask = lchip->dev->coherent_dma_mask; 244 245 if (info->offset) 246 dev->mapbase = lchip->base + info->offset; 247 else 248 dev->mapbase = 0; 249 dev->length = info->length; 250 251 dev->irq[0] = (lchip->irq_base == NO_IRQ) ? 252 NO_IRQ : lchip->irq_base + info->irq[0]; 253 254 ret = device_register(&dev->dev); 255 if (ret) { 256 out: 257 kfree(dev); 258 } 259 return ret; 260} 261 262#ifdef CONFIG_PM 263 264struct locomo_save_data { 265 u16 LCM_GPO; 266 u16 LCM_SPICT; 267 u16 LCM_GPE; 268 u16 LCM_ASD; 269 u16 LCM_SPIMD; 270}; 271 272static int locomo_suspend(struct platform_device *dev, pm_message_t state) 273{ 274 struct locomo *lchip = platform_get_drvdata(dev); 275 struct locomo_save_data *save; 276 unsigned long flags; 277 278 save = kmalloc(sizeof(struct locomo_save_data), GFP_KERNEL); 279 if (!save) 280 return -ENOMEM; 281 282 lchip->saved_state = save; 283 284 spin_lock_irqsave(&lchip->lock, flags); 285 286 save->LCM_GPO = locomo_readl(lchip->base + LOCOMO_GPO); /* GPIO */ 287 locomo_writel(0x00, lchip->base + LOCOMO_GPO); 288 save->LCM_SPICT = locomo_readl(lchip->base + LOCOMO_SPI + LOCOMO_SPICT); /* SPI */ 289 locomo_writel(0x40, lchip->base + LOCOMO_SPI + LOCOMO_SPICT); 290 save->LCM_GPE = locomo_readl(lchip->base + LOCOMO_GPE); /* GPIO */ 291 locomo_writel(0x00, lchip->base + LOCOMO_GPE); 292 save->LCM_ASD = locomo_readl(lchip->base + LOCOMO_ASD); /* ADSTART */ 293 locomo_writel(0x00, lchip->base + LOCOMO_ASD); 294 save->LCM_SPIMD = locomo_readl(lchip->base + LOCOMO_SPI + LOCOMO_SPIMD); /* SPI */ 295 locomo_writel(0x3C14, lchip->base + LOCOMO_SPI + LOCOMO_SPIMD); 296 297 locomo_writel(0x00, lchip->base + LOCOMO_PAIF); 298 locomo_writel(0x00, lchip->base + LOCOMO_DAC); 299 locomo_writel(0x00, lchip->base + LOCOMO_BACKLIGHT + LOCOMO_TC); 300 301 if ((locomo_readl(lchip->base + LOCOMO_LED + LOCOMO_LPT0) & 0x88) && (locomo_readl(lchip->base + LOCOMO_LED + LOCOMO_LPT1) & 0x88)) 302 locomo_writel(0x00, lchip->base + LOCOMO_C32K); /* CLK32 off */ 303 else 304 /* 18MHz already enabled, so no wait */ 305 locomo_writel(0xc1, lchip->base + LOCOMO_C32K); /* CLK32 on */ 306 307 locomo_writel(0x00, lchip->base + LOCOMO_TADC); /* 18MHz clock off*/ 308 locomo_writel(0x00, lchip->base + LOCOMO_AUDIO + LOCOMO_ACC); /* 22MHz/24MHz clock off */ 309 locomo_writel(0x00, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS); /* FL */ 310 311 spin_unlock_irqrestore(&lchip->lock, flags); 312 313 return 0; 314} 315 316static int locomo_resume(struct platform_device *dev) 317{ 318 struct locomo *lchip = platform_get_drvdata(dev); 319 struct locomo_save_data *save; 320 unsigned long r; 321 unsigned long flags; 322 323 save = lchip->saved_state; 324 if (!save) 325 return 0; 326 327 spin_lock_irqsave(&lchip->lock, flags); 328 329 locomo_writel(save->LCM_GPO, lchip->base + LOCOMO_GPO); 330 locomo_writel(save->LCM_SPICT, lchip->base + LOCOMO_SPI + LOCOMO_SPICT); 331 locomo_writel(save->LCM_GPE, lchip->base + LOCOMO_GPE); 332 locomo_writel(save->LCM_ASD, lchip->base + LOCOMO_ASD); 333 locomo_writel(save->LCM_SPIMD, lchip->base + LOCOMO_SPI + LOCOMO_SPIMD); 334 335 locomo_writel(0x00, lchip->base + LOCOMO_C32K); 336 locomo_writel(0x90, lchip->base + LOCOMO_TADC); 337 338 locomo_writel(0, lchip->base + LOCOMO_KEYBOARD + LOCOMO_KSC); 339 r = locomo_readl(lchip->base + LOCOMO_KEYBOARD + LOCOMO_KIC); 340 r &= 0xFEFF; 341 locomo_writel(r, lchip->base + LOCOMO_KEYBOARD + LOCOMO_KIC); 342 locomo_writel(0x1, lchip->base + LOCOMO_KEYBOARD + LOCOMO_KCMD); 343 344 spin_unlock_irqrestore(&lchip->lock, flags); 345 346 lchip->saved_state = NULL; 347 kfree(save); 348 349 return 0; 350} 351#endif 352 353static int 354__locomo_probe(struct device *me, struct resource *mem, int irq) 355{ 356 struct locomo_platform_data *pdata = me->platform_data; 357 struct locomo *lchip; 358 unsigned long r; 359 int i, ret = -ENODEV; 360 361 lchip = kzalloc(sizeof(struct locomo), GFP_KERNEL); 362 if (!lchip) 363 return -ENOMEM; 364 365 spin_lock_init(&lchip->lock); 366 367 lchip->dev = me; 368 dev_set_drvdata(lchip->dev, lchip); 369 370 lchip->phys = mem->start; 371 lchip->irq = irq; 372 lchip->irq_base = (pdata) ? pdata->irq_base : NO_IRQ; 373 374 /* 375 * Map the whole region. This also maps the 376 * registers for our children. 377 */ 378 lchip->base = ioremap(mem->start, PAGE_SIZE); 379 if (!lchip->base) { 380 ret = -ENOMEM; 381 goto out; 382 } 383 384 /* locomo initialize */ 385 locomo_writel(0, lchip->base + LOCOMO_ICR); 386 /* KEYBOARD */ 387 locomo_writel(0, lchip->base + LOCOMO_KEYBOARD + LOCOMO_KIC); 388 389 /* GPIO */ 390 locomo_writel(0, lchip->base + LOCOMO_GPO); 391 locomo_writel((LOCOMO_GPIO(1) | LOCOMO_GPIO(2) | LOCOMO_GPIO(13) | LOCOMO_GPIO(14)) 392 , lchip->base + LOCOMO_GPE); 393 locomo_writel((LOCOMO_GPIO(1) | LOCOMO_GPIO(2) | LOCOMO_GPIO(13) | LOCOMO_GPIO(14)) 394 , lchip->base + LOCOMO_GPD); 395 locomo_writel(0, lchip->base + LOCOMO_GIE); 396 397 /* Frontlight */ 398 locomo_writel(0, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS); 399 locomo_writel(0, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALD); 400 401 /* Longtime timer */ 402 locomo_writel(0, lchip->base + LOCOMO_LTINT); 403 /* SPI */ 404 locomo_writel(0, lchip->base + LOCOMO_SPI + LOCOMO_SPIIE); 405 406 locomo_writel(6 + 8 + 320 + 30 - 10, lchip->base + LOCOMO_ASD); 407 r = locomo_readl(lchip->base + LOCOMO_ASD); 408 r |= 0x8000; 409 locomo_writel(r, lchip->base + LOCOMO_ASD); 410 411 locomo_writel(6 + 8 + 320 + 30 - 10 - 128 + 4, lchip->base + LOCOMO_HSD); 412 r = locomo_readl(lchip->base + LOCOMO_HSD); 413 r |= 0x8000; 414 locomo_writel(r, lchip->base + LOCOMO_HSD); 415 416 locomo_writel(128 / 8, lchip->base + LOCOMO_HSC); 417 418 /* XON */ 419 locomo_writel(0x80, lchip->base + LOCOMO_TADC); 420 udelay(1000); 421 /* CLK9MEN */ 422 r = locomo_readl(lchip->base + LOCOMO_TADC); 423 r |= 0x10; 424 locomo_writel(r, lchip->base + LOCOMO_TADC); 425 udelay(100); 426 427 /* init DAC */ 428 r = locomo_readl(lchip->base + LOCOMO_DAC); 429 r |= LOCOMO_DAC_SCLOEB | LOCOMO_DAC_SDAOEB; 430 locomo_writel(r, lchip->base + LOCOMO_DAC); 431 432 r = locomo_readl(lchip->base + LOCOMO_VER); 433 printk(KERN_INFO "LoCoMo Chip: %lu%lu\n", (r >> 8), (r & 0xff)); 434 435 /* 436 * The interrupt controller must be initialised before any 437 * other device to ensure that the interrupts are available. 438 */ 439 if (lchip->irq != NO_IRQ && lchip->irq_base != NO_IRQ) 440 locomo_setup_irq(lchip); 441 442 for (i = 0; i < ARRAY_SIZE(locomo_devices); i++) 443 locomo_init_one_child(lchip, &locomo_devices[i]); 444 return 0; 445 446 out: 447 kfree(lchip); 448 return ret; 449} 450 451static int locomo_remove_child(struct device *dev, void *data) 452{ 453 device_unregister(dev); 454 return 0; 455} 456 457static void __locomo_remove(struct locomo *lchip) 458{ 459 device_for_each_child(lchip->dev, NULL, locomo_remove_child); 460 461 if (lchip->irq != NO_IRQ) { 462 irq_set_chained_handler_and_data(lchip->irq, NULL, NULL); 463 } 464 465 iounmap(lchip->base); 466 kfree(lchip); 467} 468 469/** 470 * locomo_probe - probe for a single LoCoMo chip. 471 * @dev: platform device 472 * 473 * Probe for a LoCoMo chip. This must be called 474 * before any other locomo-specific code. 475 * 476 * Returns: 477 * * %-EINVAL - device's IORESOURCE_MEM not found 478 * * %-ENXIO - could not allocate an IRQ for the device 479 * * %-ENODEV - device not found. 480 * * %-EBUSY - physical address already marked in-use. 481 * * %-ENOMEM - could not allocate or iomap memory. 482 * * %0 - successful. 483 */ 484static int locomo_probe(struct platform_device *dev) 485{ 486 struct resource *mem; 487 int irq; 488 489 mem = platform_get_resource(dev, IORESOURCE_MEM, 0); 490 if (!mem) 491 return -EINVAL; 492 irq = platform_get_irq(dev, 0); 493 if (irq < 0) 494 return -ENXIO; 495 496 return __locomo_probe(&dev->dev, mem, irq); 497} 498 499static void locomo_remove(struct platform_device *dev) 500{ 501 struct locomo *lchip = platform_get_drvdata(dev); 502 503 if (lchip) { 504 __locomo_remove(lchip); 505 platform_set_drvdata(dev, NULL); 506 } 507} 508 509/* 510 * Not sure if this should be on the system bus or not yet. 511 * We really want some way to register a system device at 512 * the per-machine level, and then have this driver pick 513 * up the registered devices. 514 */ 515static struct platform_driver locomo_device_driver = { 516 .probe = locomo_probe, 517 .remove_new = locomo_remove, 518#ifdef CONFIG_PM 519 .suspend = locomo_suspend, 520 .resume = locomo_resume, 521#endif 522 .driver = { 523 .name = "locomo", 524 }, 525}; 526 527/* 528 * Get the parent device driver (us) structure 529 * from a child function device 530 */ 531static inline struct locomo *locomo_chip_driver(struct locomo_dev *ldev) 532{ 533 return (struct locomo *)dev_get_drvdata(ldev->dev.parent); 534} 535 536void locomo_gpio_set_dir(struct device *dev, unsigned int bits, unsigned int dir) 537{ 538 struct locomo *lchip = dev_get_drvdata(dev); 539 unsigned long flags; 540 unsigned int r; 541 542 if (!lchip) 543 return; 544 545 spin_lock_irqsave(&lchip->lock, flags); 546 547 r = locomo_readl(lchip->base + LOCOMO_GPD); 548 if (dir) 549 r |= bits; 550 else 551 r &= ~bits; 552 locomo_writel(r, lchip->base + LOCOMO_GPD); 553 554 r = locomo_readl(lchip->base + LOCOMO_GPE); 555 if (dir) 556 r |= bits; 557 else 558 r &= ~bits; 559 locomo_writel(r, lchip->base + LOCOMO_GPE); 560 561 spin_unlock_irqrestore(&lchip->lock, flags); 562} 563EXPORT_SYMBOL(locomo_gpio_set_dir); 564 565int locomo_gpio_read_level(struct device *dev, unsigned int bits) 566{ 567 struct locomo *lchip = dev_get_drvdata(dev); 568 unsigned long flags; 569 unsigned int ret; 570 571 if (!lchip) 572 return -ENODEV; 573 574 spin_lock_irqsave(&lchip->lock, flags); 575 ret = locomo_readl(lchip->base + LOCOMO_GPL); 576 spin_unlock_irqrestore(&lchip->lock, flags); 577 578 ret &= bits; 579 return ret; 580} 581EXPORT_SYMBOL(locomo_gpio_read_level); 582 583int locomo_gpio_read_output(struct device *dev, unsigned int bits) 584{ 585 struct locomo *lchip = dev_get_drvdata(dev); 586 unsigned long flags; 587 unsigned int ret; 588 589 if (!lchip) 590 return -ENODEV; 591 592 spin_lock_irqsave(&lchip->lock, flags); 593 ret = locomo_readl(lchip->base + LOCOMO_GPO); 594 spin_unlock_irqrestore(&lchip->lock, flags); 595 596 ret &= bits; 597 return ret; 598} 599EXPORT_SYMBOL(locomo_gpio_read_output); 600 601void locomo_gpio_write(struct device *dev, unsigned int bits, unsigned int set) 602{ 603 struct locomo *lchip = dev_get_drvdata(dev); 604 unsigned long flags; 605 unsigned int r; 606 607 if (!lchip) 608 return; 609 610 spin_lock_irqsave(&lchip->lock, flags); 611 612 r = locomo_readl(lchip->base + LOCOMO_GPO); 613 if (set) 614 r |= bits; 615 else 616 r &= ~bits; 617 locomo_writel(r, lchip->base + LOCOMO_GPO); 618 619 spin_unlock_irqrestore(&lchip->lock, flags); 620} 621EXPORT_SYMBOL(locomo_gpio_write); 622 623static void locomo_m62332_sendbit(void *mapbase, int bit) 624{ 625 unsigned int r; 626 627 r = locomo_readl(mapbase + LOCOMO_DAC); 628 r &= ~(LOCOMO_DAC_SCLOEB); 629 locomo_writel(r, mapbase + LOCOMO_DAC); 630 udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ 631 udelay(DAC_DATA_HOLD_TIME); /* 300 nsec */ 632 r = locomo_readl(mapbase + LOCOMO_DAC); 633 r &= ~(LOCOMO_DAC_SCLOEB); 634 locomo_writel(r, mapbase + LOCOMO_DAC); 635 udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ 636 udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ 637 638 if (bit & 1) { 639 r = locomo_readl(mapbase + LOCOMO_DAC); 640 r |= LOCOMO_DAC_SDAOEB; 641 locomo_writel(r, mapbase + LOCOMO_DAC); 642 udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ 643 } else { 644 r = locomo_readl(mapbase + LOCOMO_DAC); 645 r &= ~(LOCOMO_DAC_SDAOEB); 646 locomo_writel(r, mapbase + LOCOMO_DAC); 647 udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ 648 } 649 650 udelay(DAC_DATA_SETUP_TIME); /* 250 nsec */ 651 r = locomo_readl(mapbase + LOCOMO_DAC); 652 r |= LOCOMO_DAC_SCLOEB; 653 locomo_writel(r, mapbase + LOCOMO_DAC); 654 udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ 655 udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.0 usec */ 656} 657 658void locomo_m62332_senddata(struct locomo_dev *ldev, unsigned int dac_data, int channel) 659{ 660 struct locomo *lchip = locomo_chip_driver(ldev); 661 int i; 662 unsigned char data; 663 unsigned int r; 664 void *mapbase = lchip->base; 665 unsigned long flags; 666 667 spin_lock_irqsave(&lchip->lock, flags); 668 669 /* Start */ 670 udelay(DAC_BUS_FREE_TIME); /* 5.0 usec */ 671 r = locomo_readl(mapbase + LOCOMO_DAC); 672 r |= LOCOMO_DAC_SCLOEB | LOCOMO_DAC_SDAOEB; 673 locomo_writel(r, mapbase + LOCOMO_DAC); 674 udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ 675 udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.0 usec */ 676 r = locomo_readl(mapbase + LOCOMO_DAC); 677 r &= ~(LOCOMO_DAC_SDAOEB); 678 locomo_writel(r, mapbase + LOCOMO_DAC); 679 udelay(DAC_START_HOLD_TIME); /* 5.0 usec */ 680 udelay(DAC_DATA_HOLD_TIME); /* 300 nsec */ 681 682 /* Send slave address and W bit (LSB is W bit) */ 683 data = (M62332_SLAVE_ADDR << 1) | M62332_W_BIT; 684 for (i = 1; i <= 8; i++) { 685 locomo_m62332_sendbit(mapbase, data >> (8 - i)); 686 } 687 688 /* Check A bit */ 689 r = locomo_readl(mapbase + LOCOMO_DAC); 690 r &= ~(LOCOMO_DAC_SCLOEB); 691 locomo_writel(r, mapbase + LOCOMO_DAC); 692 udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ 693 udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ 694 r = locomo_readl(mapbase + LOCOMO_DAC); 695 r &= ~(LOCOMO_DAC_SDAOEB); 696 locomo_writel(r, mapbase + LOCOMO_DAC); 697 udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ 698 r = locomo_readl(mapbase + LOCOMO_DAC); 699 r |= LOCOMO_DAC_SCLOEB; 700 locomo_writel(r, mapbase + LOCOMO_DAC); 701 udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ 702 udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.7 usec */ 703 if (locomo_readl(mapbase + LOCOMO_DAC) & LOCOMO_DAC_SDAOEB) { /* High is error */ 704 printk(KERN_WARNING "locomo: m62332_senddata Error 1\n"); 705 goto out; 706 } 707 708 /* Send Sub address (LSB is channel select) */ 709 /* channel = 0 : ch1 select */ 710 /* = 1 : ch2 select */ 711 data = M62332_SUB_ADDR + channel; 712 for (i = 1; i <= 8; i++) { 713 locomo_m62332_sendbit(mapbase, data >> (8 - i)); 714 } 715 716 /* Check A bit */ 717 r = locomo_readl(mapbase + LOCOMO_DAC); 718 r &= ~(LOCOMO_DAC_SCLOEB); 719 locomo_writel(r, mapbase + LOCOMO_DAC); 720 udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ 721 udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ 722 r = locomo_readl(mapbase + LOCOMO_DAC); 723 r &= ~(LOCOMO_DAC_SDAOEB); 724 locomo_writel(r, mapbase + LOCOMO_DAC); 725 udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ 726 r = locomo_readl(mapbase + LOCOMO_DAC); 727 r |= LOCOMO_DAC_SCLOEB; 728 locomo_writel(r, mapbase + LOCOMO_DAC); 729 udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ 730 udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.7 usec */ 731 if (locomo_readl(mapbase + LOCOMO_DAC) & LOCOMO_DAC_SDAOEB) { /* High is error */ 732 printk(KERN_WARNING "locomo: m62332_senddata Error 2\n"); 733 goto out; 734 } 735 736 /* Send DAC data */ 737 for (i = 1; i <= 8; i++) { 738 locomo_m62332_sendbit(mapbase, dac_data >> (8 - i)); 739 } 740 741 /* Check A bit */ 742 r = locomo_readl(mapbase + LOCOMO_DAC); 743 r &= ~(LOCOMO_DAC_SCLOEB); 744 locomo_writel(r, mapbase + LOCOMO_DAC); 745 udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ 746 udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ 747 r = locomo_readl(mapbase + LOCOMO_DAC); 748 r &= ~(LOCOMO_DAC_SDAOEB); 749 locomo_writel(r, mapbase + LOCOMO_DAC); 750 udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ 751 r = locomo_readl(mapbase + LOCOMO_DAC); 752 r |= LOCOMO_DAC_SCLOEB; 753 locomo_writel(r, mapbase + LOCOMO_DAC); 754 udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ 755 udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4.7 usec */ 756 if (locomo_readl(mapbase + LOCOMO_DAC) & LOCOMO_DAC_SDAOEB) { /* High is error */ 757 printk(KERN_WARNING "locomo: m62332_senddata Error 3\n"); 758 } 759 760out: 761 /* stop */ 762 r = locomo_readl(mapbase + LOCOMO_DAC); 763 r &= ~(LOCOMO_DAC_SCLOEB); 764 locomo_writel(r, mapbase + LOCOMO_DAC); 765 udelay(DAC_LOW_SETUP_TIME); /* 300 nsec */ 766 udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ 767 r = locomo_readl(mapbase + LOCOMO_DAC); 768 r |= LOCOMO_DAC_SCLOEB; 769 locomo_writel(r, mapbase + LOCOMO_DAC); 770 udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ 771 udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4 usec */ 772 r = locomo_readl(mapbase + LOCOMO_DAC); 773 r |= LOCOMO_DAC_SDAOEB; 774 locomo_writel(r, mapbase + LOCOMO_DAC); 775 udelay(DAC_HIGH_SETUP_TIME); /* 1000 nsec */ 776 udelay(DAC_SCL_HIGH_HOLD_TIME); /* 4 usec */ 777 778 r = locomo_readl(mapbase + LOCOMO_DAC); 779 r |= LOCOMO_DAC_SCLOEB | LOCOMO_DAC_SDAOEB; 780 locomo_writel(r, mapbase + LOCOMO_DAC); 781 udelay(DAC_LOW_SETUP_TIME); /* 1000 nsec */ 782 udelay(DAC_SCL_LOW_HOLD_TIME); /* 4.7 usec */ 783 784 spin_unlock_irqrestore(&lchip->lock, flags); 785} 786EXPORT_SYMBOL(locomo_m62332_senddata); 787 788/* 789 * Frontlight control 790 */ 791 792void locomo_frontlight_set(struct locomo_dev *dev, int duty, int vr, int bpwf) 793{ 794 unsigned long flags; 795 struct locomo *lchip = locomo_chip_driver(dev); 796 797 if (vr) 798 locomo_gpio_write(dev->dev.parent, LOCOMO_GPIO_FL_VR, 1); 799 else 800 locomo_gpio_write(dev->dev.parent, LOCOMO_GPIO_FL_VR, 0); 801 802 spin_lock_irqsave(&lchip->lock, flags); 803 locomo_writel(bpwf, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS); 804 udelay(100); 805 locomo_writel(duty, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALD); 806 locomo_writel(bpwf | LOCOMO_ALC_EN, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS); 807 spin_unlock_irqrestore(&lchip->lock, flags); 808} 809EXPORT_SYMBOL(locomo_frontlight_set); 810 811/* 812 * LoCoMo "Register Access Bus." 813 * 814 * We model this as a regular bus type, and hang devices directly 815 * off this. 816 */ 817static int locomo_match(struct device *_dev, struct device_driver *_drv) 818{ 819 struct locomo_dev *dev = LOCOMO_DEV(_dev); 820 struct locomo_driver *drv = LOCOMO_DRV(_drv); 821 822 return dev->devid == drv->devid; 823} 824 825static int locomo_bus_probe(struct device *dev) 826{ 827 struct locomo_dev *ldev = LOCOMO_DEV(dev); 828 struct locomo_driver *drv = LOCOMO_DRV(dev->driver); 829 int ret = -ENODEV; 830 831 if (drv->probe) 832 ret = drv->probe(ldev); 833 return ret; 834} 835 836static void locomo_bus_remove(struct device *dev) 837{ 838 struct locomo_dev *ldev = LOCOMO_DEV(dev); 839 struct locomo_driver *drv = LOCOMO_DRV(dev->driver); 840 841 if (drv->remove) 842 drv->remove(ldev); 843} 844 845struct bus_type locomo_bus_type = { 846 .name = "locomo-bus", 847 .match = locomo_match, 848 .probe = locomo_bus_probe, 849 .remove = locomo_bus_remove, 850}; 851 852int locomo_driver_register(struct locomo_driver *driver) 853{ 854 driver->drv.bus = &locomo_bus_type; 855 return driver_register(&driver->drv); 856} 857EXPORT_SYMBOL(locomo_driver_register); 858 859void locomo_driver_unregister(struct locomo_driver *driver) 860{ 861 driver_unregister(&driver->drv); 862} 863EXPORT_SYMBOL(locomo_driver_unregister); 864 865static int __init locomo_init(void) 866{ 867 int ret = bus_register(&locomo_bus_type); 868 if (ret == 0) 869 platform_driver_register(&locomo_device_driver); 870 return ret; 871} 872 873static void __exit locomo_exit(void) 874{ 875 platform_driver_unregister(&locomo_device_driver); 876 bus_unregister(&locomo_bus_type); 877} 878 879module_init(locomo_init); 880module_exit(locomo_exit); 881 882MODULE_DESCRIPTION("Sharp LoCoMo core driver"); 883MODULE_LICENSE("GPL"); 884MODULE_AUTHOR("John Lenz <lenz@cs.wisc.edu>"); 885