1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * Copyright (c) 2014-2016, Fuzhou Rockchip Electronics Co., Ltd 4 * Caesar Wang <wxt@rock-chips.com> 5 */ 6 7#include <linux/clk.h> 8#include <linux/delay.h> 9#include <linux/interrupt.h> 10#include <linux/io.h> 11#include <linux/module.h> 12#include <linux/of.h> 13#include <linux/of_address.h> 14#include <linux/of_irq.h> 15#include <linux/platform_device.h> 16#include <linux/regmap.h> 17#include <linux/reset.h> 18#include <linux/thermal.h> 19#include <linux/mfd/syscon.h> 20#include <linux/pinctrl/consumer.h> 21 22/* 23 * If the temperature over a period of time High, 24 * the resulting TSHUT gave CRU module,let it reset the entire chip, 25 * or via GPIO give PMIC. 26 */ 27enum tshut_mode { 28 TSHUT_MODE_CRU = 0, 29 TSHUT_MODE_GPIO, 30}; 31 32/* 33 * The system Temperature Sensors tshut(tshut) polarity 34 * the bit 8 is tshut polarity. 35 * 0: low active, 1: high active 36 */ 37enum tshut_polarity { 38 TSHUT_LOW_ACTIVE = 0, 39 TSHUT_HIGH_ACTIVE, 40}; 41 42/* 43 * The system has two Temperature Sensors. 44 * sensor0 is for CPU, and sensor1 is for GPU. 45 */ 46enum sensor_id { 47 SENSOR_CPU = 0, 48 SENSOR_GPU, 49}; 50 51/* 52 * The conversion table has the adc value and temperature. 53 * ADC_DECREMENT: the adc value is of diminishing.(e.g. rk3288_code_table) 54 * ADC_INCREMENT: the adc value is incremental.(e.g. rk3368_code_table) 55 */ 56enum adc_sort_mode { 57 ADC_DECREMENT = 0, 58 ADC_INCREMENT, 59}; 60 61#include "thermal_hwmon.h" 62 63/** 64 * The max sensors is two in rockchip SoCs. 65 * Two sensors: CPU and GPU sensor. 66 */ 67#define SOC_MAX_SENSORS 2 68 69/** 70 * struct chip_tsadc_table - hold information about chip-specific differences 71 * @id: conversion table 72 * @length: size of conversion table 73 * @data_mask: mask to apply on data inputs 74 * @mode: sort mode of this adc variant (incrementing or decrementing) 75 */ 76struct chip_tsadc_table { 77 const struct tsadc_table *id; 78 unsigned int length; 79 u32 data_mask; 80 enum adc_sort_mode mode; 81}; 82 83/** 84 * struct rockchip_tsadc_chip - hold the private data of tsadc chip 85 * @chn_id: array of sensor ids of chip corresponding to the channel 86 * @chn_num: the channel number of tsadc chip 87 * @tshut_temp: the hardware-controlled shutdown temperature value 88 * @tshut_mode: the hardware-controlled shutdown mode (0:CRU 1:GPIO) 89 * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH) 90 * @initialize: SoC special initialize tsadc controller method 91 * @irq_ack: clear the interrupt 92 * @control: enable/disable method for the tsadc controller 93 * @get_temp: get the temperature 94 * @set_alarm_temp: set the high temperature interrupt 95 * @set_tshut_temp: set the hardware-controlled shutdown temperature 96 * @set_tshut_mode: set the hardware-controlled shutdown mode 97 * @table: the chip-specific conversion table 98 */ 99struct rockchip_tsadc_chip { 100 /* The sensor id of chip correspond to the ADC channel */ 101 int chn_id[SOC_MAX_SENSORS]; 102 int chn_num; 103 104 /* The hardware-controlled tshut property */ 105 int tshut_temp; 106 enum tshut_mode tshut_mode; 107 enum tshut_polarity tshut_polarity; 108 109 /* Chip-wide methods */ 110 void (*initialize)(struct regmap *grf, 111 void __iomem *reg, enum tshut_polarity p); 112 void (*irq_ack)(void __iomem *reg); 113 void (*control)(void __iomem *reg, bool on); 114 115 /* Per-sensor methods */ 116 int (*get_temp)(const struct chip_tsadc_table *table, 117 int chn, void __iomem *reg, int *temp); 118 int (*set_alarm_temp)(const struct chip_tsadc_table *table, 119 int chn, void __iomem *reg, int temp); 120 int (*set_tshut_temp)(const struct chip_tsadc_table *table, 121 int chn, void __iomem *reg, int temp); 122 void (*set_tshut_mode)(int chn, void __iomem *reg, enum tshut_mode m); 123 124 /* Per-table methods */ 125 struct chip_tsadc_table table; 126}; 127 128/** 129 * struct rockchip_thermal_sensor - hold the information of thermal sensor 130 * @thermal: pointer to the platform/configuration data 131 * @tzd: pointer to a thermal zone 132 * @id: identifier of the thermal sensor 133 */ 134struct rockchip_thermal_sensor { 135 struct rockchip_thermal_data *thermal; 136 struct thermal_zone_device *tzd; 137 int id; 138}; 139 140/** 141 * struct rockchip_thermal_data - hold the private data of thermal driver 142 * @chip: pointer to the platform/configuration data 143 * @pdev: platform device of thermal 144 * @reset: the reset controller of tsadc 145 * @sensors: array of thermal sensors 146 * @clk: the controller clock is divided by the exteral 24MHz 147 * @pclk: the advanced peripherals bus clock 148 * @grf: the general register file will be used to do static set by software 149 * @regs: the base address of tsadc controller 150 * @tshut_temp: the hardware-controlled shutdown temperature value 151 * @tshut_mode: the hardware-controlled shutdown mode (0:CRU 1:GPIO) 152 * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH) 153 */ 154struct rockchip_thermal_data { 155 const struct rockchip_tsadc_chip *chip; 156 struct platform_device *pdev; 157 struct reset_control *reset; 158 159 struct rockchip_thermal_sensor sensors[SOC_MAX_SENSORS]; 160 161 struct clk *clk; 162 struct clk *pclk; 163 164 struct regmap *grf; 165 void __iomem *regs; 166 167 int tshut_temp; 168 enum tshut_mode tshut_mode; 169 enum tshut_polarity tshut_polarity; 170}; 171 172/** 173 * TSADC Sensor Register description: 174 * 175 * TSADCV2_* are used for RK3288 SoCs, the other chips can reuse it. 176 * TSADCV3_* are used for newer SoCs than RK3288. (e.g: RK3228, RK3399) 177 * 178 */ 179#define TSADCV2_USER_CON 0x00 180#define TSADCV2_AUTO_CON 0x04 181#define TSADCV2_INT_EN 0x08 182#define TSADCV2_INT_PD 0x0c 183#define TSADCV2_DATA(chn) (0x20 + (chn) * 0x04) 184#define TSADCV2_COMP_INT(chn) (0x30 + (chn) * 0x04) 185#define TSADCV2_COMP_SHUT(chn) (0x40 + (chn) * 0x04) 186#define TSADCV2_HIGHT_INT_DEBOUNCE 0x60 187#define TSADCV2_HIGHT_TSHUT_DEBOUNCE 0x64 188#define TSADCV2_AUTO_PERIOD 0x68 189#define TSADCV2_AUTO_PERIOD_HT 0x6c 190 191#define TSADCV2_AUTO_EN BIT(0) 192#define TSADCV2_AUTO_SRC_EN(chn) BIT(4 + (chn)) 193#define TSADCV2_AUTO_TSHUT_POLARITY_HIGH BIT(8) 194 195#define TSADCV3_AUTO_Q_SEL_EN BIT(1) 196 197#define TSADCV2_INT_SRC_EN(chn) BIT(chn) 198#define TSADCV2_SHUT_2GPIO_SRC_EN(chn) BIT(4 + (chn)) 199#define TSADCV2_SHUT_2CRU_SRC_EN(chn) BIT(8 + (chn)) 200 201#define TSADCV2_INT_PD_CLEAR_MASK ~BIT(8) 202#define TSADCV3_INT_PD_CLEAR_MASK ~BIT(16) 203 204#define TSADCV2_DATA_MASK 0xfff 205#define TSADCV3_DATA_MASK 0x3ff 206 207#define TSADCV2_HIGHT_INT_DEBOUNCE_COUNT 4 208#define TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT 4 209#define TSADCV2_AUTO_PERIOD_TIME 250 /* 250ms */ 210#define TSADCV2_AUTO_PERIOD_HT_TIME 50 /* 50ms */ 211#define TSADCV3_AUTO_PERIOD_TIME 1875 /* 2.5ms */ 212#define TSADCV3_AUTO_PERIOD_HT_TIME 1875 /* 2.5ms */ 213 214#define TSADCV2_USER_INTER_PD_SOC 0x340 /* 13 clocks */ 215 216#define GRF_SARADC_TESTBIT 0x0e644 217#define GRF_TSADC_TESTBIT_L 0x0e648 218#define GRF_TSADC_TESTBIT_H 0x0e64c 219 220#define PX30_GRF_SOC_CON2 0x0408 221 222#define GRF_SARADC_TESTBIT_ON (0x10001 << 2) 223#define GRF_TSADC_TESTBIT_H_ON (0x10001 << 2) 224#define GRF_TSADC_VCM_EN_L (0x10001 << 7) 225#define GRF_TSADC_VCM_EN_H (0x10001 << 7) 226 227#define GRF_CON_TSADC_CH_INV (0x10001 << 1) 228 229/** 230 * struct tsadc_table - code to temperature conversion table 231 * @code: the value of adc channel 232 * @temp: the temperature 233 * Note: 234 * code to temperature mapping of the temperature sensor is a piece wise linear 235 * curve.Any temperature, code faling between to 2 give temperatures can be 236 * linearly interpolated. 237 * Code to Temperature mapping should be updated based on manufacturer results. 238 */ 239struct tsadc_table { 240 u32 code; 241 int temp; 242}; 243 244static const struct tsadc_table rv1108_table[] = { 245 {0, -40000}, 246 {374, -40000}, 247 {382, -35000}, 248 {389, -30000}, 249 {397, -25000}, 250 {405, -20000}, 251 {413, -15000}, 252 {421, -10000}, 253 {429, -5000}, 254 {436, 0}, 255 {444, 5000}, 256 {452, 10000}, 257 {460, 15000}, 258 {468, 20000}, 259 {476, 25000}, 260 {483, 30000}, 261 {491, 35000}, 262 {499, 40000}, 263 {507, 45000}, 264 {515, 50000}, 265 {523, 55000}, 266 {531, 60000}, 267 {539, 65000}, 268 {547, 70000}, 269 {555, 75000}, 270 {562, 80000}, 271 {570, 85000}, 272 {578, 90000}, 273 {586, 95000}, 274 {594, 100000}, 275 {602, 105000}, 276 {610, 110000}, 277 {618, 115000}, 278 {626, 120000}, 279 {634, 125000}, 280 {TSADCV2_DATA_MASK, 125000}, 281}; 282 283static const struct tsadc_table rk3228_code_table[] = { 284 {0, -40000}, 285 {588, -40000}, 286 {593, -35000}, 287 {598, -30000}, 288 {603, -25000}, 289 {608, -20000}, 290 {613, -15000}, 291 {618, -10000}, 292 {623, -5000}, 293 {629, 0}, 294 {634, 5000}, 295 {639, 10000}, 296 {644, 15000}, 297 {649, 20000}, 298 {654, 25000}, 299 {660, 30000}, 300 {665, 35000}, 301 {670, 40000}, 302 {675, 45000}, 303 {681, 50000}, 304 {686, 55000}, 305 {691, 60000}, 306 {696, 65000}, 307 {702, 70000}, 308 {707, 75000}, 309 {712, 80000}, 310 {717, 85000}, 311 {723, 90000}, 312 {728, 95000}, 313 {733, 100000}, 314 {738, 105000}, 315 {744, 110000}, 316 {749, 115000}, 317 {754, 120000}, 318 {760, 125000}, 319 {TSADCV2_DATA_MASK, 125000}, 320}; 321 322static const struct tsadc_table rk3288_code_table[] = { 323 {TSADCV2_DATA_MASK, -40000}, 324 {3800, -40000}, 325 {3792, -35000}, 326 {3783, -30000}, 327 {3774, -25000}, 328 {3765, -20000}, 329 {3756, -15000}, 330 {3747, -10000}, 331 {3737, -5000}, 332 {3728, 0}, 333 {3718, 5000}, 334 {3708, 10000}, 335 {3698, 15000}, 336 {3688, 20000}, 337 {3678, 25000}, 338 {3667, 30000}, 339 {3656, 35000}, 340 {3645, 40000}, 341 {3634, 45000}, 342 {3623, 50000}, 343 {3611, 55000}, 344 {3600, 60000}, 345 {3588, 65000}, 346 {3575, 70000}, 347 {3563, 75000}, 348 {3550, 80000}, 349 {3537, 85000}, 350 {3524, 90000}, 351 {3510, 95000}, 352 {3496, 100000}, 353 {3482, 105000}, 354 {3467, 110000}, 355 {3452, 115000}, 356 {3437, 120000}, 357 {3421, 125000}, 358 {0, 125000}, 359}; 360 361static const struct tsadc_table rk3328_code_table[] = { 362 {0, -40000}, 363 {296, -40000}, 364 {304, -35000}, 365 {313, -30000}, 366 {331, -20000}, 367 {340, -15000}, 368 {349, -10000}, 369 {359, -5000}, 370 {368, 0}, 371 {378, 5000}, 372 {388, 10000}, 373 {398, 15000}, 374 {408, 20000}, 375 {418, 25000}, 376 {429, 30000}, 377 {440, 35000}, 378 {451, 40000}, 379 {462, 45000}, 380 {473, 50000}, 381 {485, 55000}, 382 {496, 60000}, 383 {508, 65000}, 384 {521, 70000}, 385 {533, 75000}, 386 {546, 80000}, 387 {559, 85000}, 388 {572, 90000}, 389 {586, 95000}, 390 {600, 100000}, 391 {614, 105000}, 392 {629, 110000}, 393 {644, 115000}, 394 {659, 120000}, 395 {675, 125000}, 396 {TSADCV2_DATA_MASK, 125000}, 397}; 398 399static const struct tsadc_table rk3368_code_table[] = { 400 {0, -40000}, 401 {106, -40000}, 402 {108, -35000}, 403 {110, -30000}, 404 {112, -25000}, 405 {114, -20000}, 406 {116, -15000}, 407 {118, -10000}, 408 {120, -5000}, 409 {122, 0}, 410 {124, 5000}, 411 {126, 10000}, 412 {128, 15000}, 413 {130, 20000}, 414 {132, 25000}, 415 {134, 30000}, 416 {136, 35000}, 417 {138, 40000}, 418 {140, 45000}, 419 {142, 50000}, 420 {144, 55000}, 421 {146, 60000}, 422 {148, 65000}, 423 {150, 70000}, 424 {152, 75000}, 425 {154, 80000}, 426 {156, 85000}, 427 {158, 90000}, 428 {160, 95000}, 429 {162, 100000}, 430 {163, 105000}, 431 {165, 110000}, 432 {167, 115000}, 433 {169, 120000}, 434 {171, 125000}, 435 {TSADCV3_DATA_MASK, 125000}, 436}; 437 438static const struct tsadc_table rk3399_code_table[] = { 439 {0, -40000}, 440 {402, -40000}, 441 {410, -35000}, 442 {419, -30000}, 443 {427, -25000}, 444 {436, -20000}, 445 {444, -15000}, 446 {453, -10000}, 447 {461, -5000}, 448 {470, 0}, 449 {478, 5000}, 450 {487, 10000}, 451 {496, 15000}, 452 {504, 20000}, 453 {513, 25000}, 454 {521, 30000}, 455 {530, 35000}, 456 {538, 40000}, 457 {547, 45000}, 458 {555, 50000}, 459 {564, 55000}, 460 {573, 60000}, 461 {581, 65000}, 462 {590, 70000}, 463 {599, 75000}, 464 {607, 80000}, 465 {616, 85000}, 466 {624, 90000}, 467 {633, 95000}, 468 {642, 100000}, 469 {650, 105000}, 470 {659, 110000}, 471 {668, 115000}, 472 {677, 120000}, 473 {685, 125000}, 474 {TSADCV3_DATA_MASK, 125000}, 475}; 476 477static u32 rk_tsadcv2_temp_to_code(const struct chip_tsadc_table *table, 478 int temp) 479{ 480 int high, low, mid; 481 unsigned long num; 482 unsigned int denom; 483 u32 error = table->data_mask; 484 485 low = 0; 486 high = (table->length - 1) - 1; /* ignore the last check for table */ 487 mid = (high + low) / 2; 488 489 /* Return mask code data when the temp is over table range */ 490 if (temp < table->id[low].temp || temp > table->id[high].temp) 491 goto exit; 492 493 while (low <= high) { 494 if (temp == table->id[mid].temp) 495 return table->id[mid].code; 496 else if (temp < table->id[mid].temp) 497 high = mid - 1; 498 else 499 low = mid + 1; 500 mid = (low + high) / 2; 501 } 502 503 /* 504 * The conversion code granularity provided by the table. Let's 505 * assume that the relationship between temperature and 506 * analog value between 2 table entries is linear and interpolate 507 * to produce less granular result. 508 */ 509 num = abs(table->id[mid + 1].code - table->id[mid].code); 510 num *= temp - table->id[mid].temp; 511 denom = table->id[mid + 1].temp - table->id[mid].temp; 512 513 switch (table->mode) { 514 case ADC_DECREMENT: 515 return table->id[mid].code - (num / denom); 516 case ADC_INCREMENT: 517 return table->id[mid].code + (num / denom); 518 default: 519 pr_err("%s: unknown table mode: %d\n", __func__, table->mode); 520 return error; 521 } 522 523exit: 524 pr_err("%s: invalid temperature, temp=%d error=%d\n", 525 __func__, temp, error); 526 return error; 527} 528 529static int rk_tsadcv2_code_to_temp(const struct chip_tsadc_table *table, 530 u32 code, int *temp) 531{ 532 unsigned int low = 1; 533 unsigned int high = table->length - 1; 534 unsigned int mid = (low + high) / 2; 535 unsigned int num; 536 unsigned long denom; 537 538 WARN_ON(table->length < 2); 539 540 switch (table->mode) { 541 case ADC_DECREMENT: 542 code &= table->data_mask; 543 if (code <= table->id[high].code) 544 return -EAGAIN; /* Incorrect reading */ 545 546 while (low <= high) { 547 if (code >= table->id[mid].code && 548 code < table->id[mid - 1].code) 549 break; 550 else if (code < table->id[mid].code) 551 low = mid + 1; 552 else 553 high = mid - 1; 554 555 mid = (low + high) / 2; 556 } 557 break; 558 case ADC_INCREMENT: 559 code &= table->data_mask; 560 if (code < table->id[low].code) 561 return -EAGAIN; /* Incorrect reading */ 562 563 while (low <= high) { 564 if (code <= table->id[mid].code && 565 code > table->id[mid - 1].code) 566 break; 567 else if (code > table->id[mid].code) 568 low = mid + 1; 569 else 570 high = mid - 1; 571 572 mid = (low + high) / 2; 573 } 574 break; 575 default: 576 pr_err("%s: unknown table mode: %d\n", __func__, table->mode); 577 return -EINVAL; 578 } 579 580 /* 581 * The 5C granularity provided by the table is too much. Let's 582 * assume that the relationship between sensor readings and 583 * temperature between 2 table entries is linear and interpolate 584 * to produce less granular result. 585 */ 586 num = table->id[mid].temp - table->id[mid - 1].temp; 587 num *= abs(table->id[mid - 1].code - code); 588 denom = abs(table->id[mid - 1].code - table->id[mid].code); 589 *temp = table->id[mid - 1].temp + (num / denom); 590 591 return 0; 592} 593 594/** 595 * rk_tsadcv2_initialize - initialize TASDC Controller. 596 * @grf: the general register file will be used to do static set by software 597 * @regs: the base address of tsadc controller 598 * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH) 599 * 600 * (1) Set TSADC_V2_AUTO_PERIOD: 601 * Configure the interleave between every two accessing of 602 * TSADC in normal operation. 603 * 604 * (2) Set TSADCV2_AUTO_PERIOD_HT: 605 * Configure the interleave between every two accessing of 606 * TSADC after the temperature is higher than COM_SHUT or COM_INT. 607 * 608 * (3) Set TSADCV2_HIGH_INT_DEBOUNCE and TSADC_HIGHT_TSHUT_DEBOUNCE: 609 * If the temperature is higher than COMP_INT or COMP_SHUT for 610 * "debounce" times, TSADC controller will generate interrupt or TSHUT. 611 */ 612static void rk_tsadcv2_initialize(struct regmap *grf, void __iomem *regs, 613 enum tshut_polarity tshut_polarity) 614{ 615 if (tshut_polarity == TSHUT_HIGH_ACTIVE) 616 writel_relaxed(0U | TSADCV2_AUTO_TSHUT_POLARITY_HIGH, 617 regs + TSADCV2_AUTO_CON); 618 else 619 writel_relaxed(0U & ~TSADCV2_AUTO_TSHUT_POLARITY_HIGH, 620 regs + TSADCV2_AUTO_CON); 621 622 writel_relaxed(TSADCV2_AUTO_PERIOD_TIME, regs + TSADCV2_AUTO_PERIOD); 623 writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_COUNT, 624 regs + TSADCV2_HIGHT_INT_DEBOUNCE); 625 writel_relaxed(TSADCV2_AUTO_PERIOD_HT_TIME, 626 regs + TSADCV2_AUTO_PERIOD_HT); 627 writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT, 628 regs + TSADCV2_HIGHT_TSHUT_DEBOUNCE); 629} 630 631/** 632 * rk_tsadcv3_initialize - initialize TASDC Controller. 633 * @grf: the general register file will be used to do static set by software 634 * @regs: the base address of tsadc controller 635 * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH) 636 * 637 * (1) The tsadc control power sequence. 638 * 639 * (2) Set TSADC_V2_AUTO_PERIOD: 640 * Configure the interleave between every two accessing of 641 * TSADC in normal operation. 642 * 643 * (2) Set TSADCV2_AUTO_PERIOD_HT: 644 * Configure the interleave between every two accessing of 645 * TSADC after the temperature is higher than COM_SHUT or COM_INT. 646 * 647 * (3) Set TSADCV2_HIGH_INT_DEBOUNCE and TSADC_HIGHT_TSHUT_DEBOUNCE: 648 * If the temperature is higher than COMP_INT or COMP_SHUT for 649 * "debounce" times, TSADC controller will generate interrupt or TSHUT. 650 */ 651static void rk_tsadcv3_initialize(struct regmap *grf, void __iomem *regs, 652 enum tshut_polarity tshut_polarity) 653{ 654 /* The tsadc control power sequence */ 655 if (IS_ERR(grf)) { 656 /* Set interleave value to workround ic time sync issue */ 657 writel_relaxed(TSADCV2_USER_INTER_PD_SOC, regs + 658 TSADCV2_USER_CON); 659 660 writel_relaxed(TSADCV2_AUTO_PERIOD_TIME, 661 regs + TSADCV2_AUTO_PERIOD); 662 writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_COUNT, 663 regs + TSADCV2_HIGHT_INT_DEBOUNCE); 664 writel_relaxed(TSADCV2_AUTO_PERIOD_HT_TIME, 665 regs + TSADCV2_AUTO_PERIOD_HT); 666 writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT, 667 regs + TSADCV2_HIGHT_TSHUT_DEBOUNCE); 668 669 } else { 670 /* Enable the voltage common mode feature */ 671 regmap_write(grf, GRF_TSADC_TESTBIT_L, GRF_TSADC_VCM_EN_L); 672 regmap_write(grf, GRF_TSADC_TESTBIT_H, GRF_TSADC_VCM_EN_H); 673 674 usleep_range(15, 100); /* The spec note says at least 15 us */ 675 regmap_write(grf, GRF_SARADC_TESTBIT, GRF_SARADC_TESTBIT_ON); 676 regmap_write(grf, GRF_TSADC_TESTBIT_H, GRF_TSADC_TESTBIT_H_ON); 677 usleep_range(90, 200); /* The spec note says at least 90 us */ 678 679 writel_relaxed(TSADCV3_AUTO_PERIOD_TIME, 680 regs + TSADCV2_AUTO_PERIOD); 681 writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_COUNT, 682 regs + TSADCV2_HIGHT_INT_DEBOUNCE); 683 writel_relaxed(TSADCV3_AUTO_PERIOD_HT_TIME, 684 regs + TSADCV2_AUTO_PERIOD_HT); 685 writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT, 686 regs + TSADCV2_HIGHT_TSHUT_DEBOUNCE); 687 } 688 689 if (tshut_polarity == TSHUT_HIGH_ACTIVE) 690 writel_relaxed(0U | TSADCV2_AUTO_TSHUT_POLARITY_HIGH, 691 regs + TSADCV2_AUTO_CON); 692 else 693 writel_relaxed(0U & ~TSADCV2_AUTO_TSHUT_POLARITY_HIGH, 694 regs + TSADCV2_AUTO_CON); 695} 696 697static void rk_tsadcv4_initialize(struct regmap *grf, void __iomem *regs, 698 enum tshut_polarity tshut_polarity) 699{ 700 rk_tsadcv2_initialize(grf, regs, tshut_polarity); 701 regmap_write(grf, PX30_GRF_SOC_CON2, GRF_CON_TSADC_CH_INV); 702} 703 704static void rk_tsadcv2_irq_ack(void __iomem *regs) 705{ 706 u32 val; 707 708 val = readl_relaxed(regs + TSADCV2_INT_PD); 709 writel_relaxed(val & TSADCV2_INT_PD_CLEAR_MASK, regs + TSADCV2_INT_PD); 710} 711 712static void rk_tsadcv3_irq_ack(void __iomem *regs) 713{ 714 u32 val; 715 716 val = readl_relaxed(regs + TSADCV2_INT_PD); 717 writel_relaxed(val & TSADCV3_INT_PD_CLEAR_MASK, regs + TSADCV2_INT_PD); 718} 719 720static void rk_tsadcv2_control(void __iomem *regs, bool enable) 721{ 722 u32 val; 723 724 val = readl_relaxed(regs + TSADCV2_AUTO_CON); 725 if (enable) 726 val |= TSADCV2_AUTO_EN; 727 else 728 val &= ~TSADCV2_AUTO_EN; 729 730 writel_relaxed(val, regs + TSADCV2_AUTO_CON); 731} 732 733/** 734 * rk_tsadcv3_control - the tsadc controller is enabled or disabled. 735 * @regs: the base address of tsadc controller 736 * @enable: boolean flag to enable the controller 737 * 738 * NOTE: TSADC controller works at auto mode, and some SoCs need set the 739 * tsadc_q_sel bit on TSADCV2_AUTO_CON[1]. The (1024 - tsadc_q) as output 740 * adc value if setting this bit to enable. 741 */ 742static void rk_tsadcv3_control(void __iomem *regs, bool enable) 743{ 744 u32 val; 745 746 val = readl_relaxed(regs + TSADCV2_AUTO_CON); 747 if (enable) 748 val |= TSADCV2_AUTO_EN | TSADCV3_AUTO_Q_SEL_EN; 749 else 750 val &= ~TSADCV2_AUTO_EN; 751 752 writel_relaxed(val, regs + TSADCV2_AUTO_CON); 753} 754 755static int rk_tsadcv2_get_temp(const struct chip_tsadc_table *table, 756 int chn, void __iomem *regs, int *temp) 757{ 758 u32 val; 759 760 val = readl_relaxed(regs + TSADCV2_DATA(chn)); 761 762 return rk_tsadcv2_code_to_temp(table, val, temp); 763} 764 765static int rk_tsadcv2_alarm_temp(const struct chip_tsadc_table *table, 766 int chn, void __iomem *regs, int temp) 767{ 768 u32 alarm_value; 769 u32 int_en, int_clr; 770 771 /* 772 * In some cases, some sensors didn't need the trip points, the 773 * set_trips will pass {-INT_MAX, INT_MAX} to trigger tsadc alarm 774 * in the end, ignore this case and disable the high temperature 775 * interrupt. 776 */ 777 if (temp == INT_MAX) { 778 int_clr = readl_relaxed(regs + TSADCV2_INT_EN); 779 int_clr &= ~TSADCV2_INT_SRC_EN(chn); 780 writel_relaxed(int_clr, regs + TSADCV2_INT_EN); 781 return 0; 782 } 783 784 /* Make sure the value is valid */ 785 alarm_value = rk_tsadcv2_temp_to_code(table, temp); 786 if (alarm_value == table->data_mask) 787 return -ERANGE; 788 789 writel_relaxed(alarm_value & table->data_mask, 790 regs + TSADCV2_COMP_INT(chn)); 791 792 int_en = readl_relaxed(regs + TSADCV2_INT_EN); 793 int_en |= TSADCV2_INT_SRC_EN(chn); 794 writel_relaxed(int_en, regs + TSADCV2_INT_EN); 795 796 return 0; 797} 798 799static int rk_tsadcv2_tshut_temp(const struct chip_tsadc_table *table, 800 int chn, void __iomem *regs, int temp) 801{ 802 u32 tshut_value, val; 803 804 /* Make sure the value is valid */ 805 tshut_value = rk_tsadcv2_temp_to_code(table, temp); 806 if (tshut_value == table->data_mask) 807 return -ERANGE; 808 809 writel_relaxed(tshut_value, regs + TSADCV2_COMP_SHUT(chn)); 810 811 /* TSHUT will be valid */ 812 val = readl_relaxed(regs + TSADCV2_AUTO_CON); 813 writel_relaxed(val | TSADCV2_AUTO_SRC_EN(chn), regs + TSADCV2_AUTO_CON); 814 815 return 0; 816} 817 818static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs, 819 enum tshut_mode mode) 820{ 821 u32 val; 822 823 val = readl_relaxed(regs + TSADCV2_INT_EN); 824 if (mode == TSHUT_MODE_GPIO) { 825 val &= ~TSADCV2_SHUT_2CRU_SRC_EN(chn); 826 val |= TSADCV2_SHUT_2GPIO_SRC_EN(chn); 827 } else { 828 val &= ~TSADCV2_SHUT_2GPIO_SRC_EN(chn); 829 val |= TSADCV2_SHUT_2CRU_SRC_EN(chn); 830 } 831 832 writel_relaxed(val, regs + TSADCV2_INT_EN); 833} 834 835static const struct rockchip_tsadc_chip px30_tsadc_data = { 836 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 837 .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */ 838 .chn_num = 2, /* 2 channels for tsadc */ 839 840 .tshut_mode = TSHUT_MODE_CRU, /* default TSHUT via CRU */ 841 .tshut_temp = 95000, 842 843 .initialize = rk_tsadcv4_initialize, 844 .irq_ack = rk_tsadcv3_irq_ack, 845 .control = rk_tsadcv3_control, 846 .get_temp = rk_tsadcv2_get_temp, 847 .set_alarm_temp = rk_tsadcv2_alarm_temp, 848 .set_tshut_temp = rk_tsadcv2_tshut_temp, 849 .set_tshut_mode = rk_tsadcv2_tshut_mode, 850 851 .table = { 852 .id = rk3328_code_table, 853 .length = ARRAY_SIZE(rk3328_code_table), 854 .data_mask = TSADCV2_DATA_MASK, 855 .mode = ADC_INCREMENT, 856 }, 857}; 858 859static const struct rockchip_tsadc_chip rv1108_tsadc_data = { 860 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 861 .chn_num = 1, /* one channel for tsadc */ 862 863 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 864 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 865 .tshut_temp = 95000, 866 867 .initialize = rk_tsadcv2_initialize, 868 .irq_ack = rk_tsadcv3_irq_ack, 869 .control = rk_tsadcv3_control, 870 .get_temp = rk_tsadcv2_get_temp, 871 .set_alarm_temp = rk_tsadcv2_alarm_temp, 872 .set_tshut_temp = rk_tsadcv2_tshut_temp, 873 .set_tshut_mode = rk_tsadcv2_tshut_mode, 874 875 .table = { 876 .id = rv1108_table, 877 .length = ARRAY_SIZE(rv1108_table), 878 .data_mask = TSADCV2_DATA_MASK, 879 .mode = ADC_INCREMENT, 880 }, 881}; 882 883static const struct rockchip_tsadc_chip rk3228_tsadc_data = { 884 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 885 .chn_num = 1, /* one channel for tsadc */ 886 887 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 888 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 889 .tshut_temp = 95000, 890 891 .initialize = rk_tsadcv2_initialize, 892 .irq_ack = rk_tsadcv3_irq_ack, 893 .control = rk_tsadcv3_control, 894 .get_temp = rk_tsadcv2_get_temp, 895 .set_alarm_temp = rk_tsadcv2_alarm_temp, 896 .set_tshut_temp = rk_tsadcv2_tshut_temp, 897 .set_tshut_mode = rk_tsadcv2_tshut_mode, 898 899 .table = { 900 .id = rk3228_code_table, 901 .length = ARRAY_SIZE(rk3228_code_table), 902 .data_mask = TSADCV3_DATA_MASK, 903 .mode = ADC_INCREMENT, 904 }, 905}; 906 907static const struct rockchip_tsadc_chip rk3288_tsadc_data = { 908 .chn_id[SENSOR_CPU] = 1, /* cpu sensor is channel 1 */ 909 .chn_id[SENSOR_GPU] = 2, /* gpu sensor is channel 2 */ 910 .chn_num = 2, /* two channels for tsadc */ 911 912 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 913 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 914 .tshut_temp = 95000, 915 916 .initialize = rk_tsadcv2_initialize, 917 .irq_ack = rk_tsadcv2_irq_ack, 918 .control = rk_tsadcv2_control, 919 .get_temp = rk_tsadcv2_get_temp, 920 .set_alarm_temp = rk_tsadcv2_alarm_temp, 921 .set_tshut_temp = rk_tsadcv2_tshut_temp, 922 .set_tshut_mode = rk_tsadcv2_tshut_mode, 923 924 .table = { 925 .id = rk3288_code_table, 926 .length = ARRAY_SIZE(rk3288_code_table), 927 .data_mask = TSADCV2_DATA_MASK, 928 .mode = ADC_DECREMENT, 929 }, 930}; 931 932static const struct rockchip_tsadc_chip rk3328_tsadc_data = { 933 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 934 .chn_num = 1, /* one channels for tsadc */ 935 936 .tshut_mode = TSHUT_MODE_CRU, /* default TSHUT via CRU */ 937 .tshut_temp = 95000, 938 939 .initialize = rk_tsadcv2_initialize, 940 .irq_ack = rk_tsadcv3_irq_ack, 941 .control = rk_tsadcv3_control, 942 .get_temp = rk_tsadcv2_get_temp, 943 .set_alarm_temp = rk_tsadcv2_alarm_temp, 944 .set_tshut_temp = rk_tsadcv2_tshut_temp, 945 .set_tshut_mode = rk_tsadcv2_tshut_mode, 946 947 .table = { 948 .id = rk3328_code_table, 949 .length = ARRAY_SIZE(rk3328_code_table), 950 .data_mask = TSADCV2_DATA_MASK, 951 .mode = ADC_INCREMENT, 952 }, 953}; 954 955static const struct rockchip_tsadc_chip rk3366_tsadc_data = { 956 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 957 .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */ 958 .chn_num = 2, /* two channels for tsadc */ 959 960 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 961 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 962 .tshut_temp = 95000, 963 964 .initialize = rk_tsadcv3_initialize, 965 .irq_ack = rk_tsadcv3_irq_ack, 966 .control = rk_tsadcv3_control, 967 .get_temp = rk_tsadcv2_get_temp, 968 .set_alarm_temp = rk_tsadcv2_alarm_temp, 969 .set_tshut_temp = rk_tsadcv2_tshut_temp, 970 .set_tshut_mode = rk_tsadcv2_tshut_mode, 971 972 .table = { 973 .id = rk3228_code_table, 974 .length = ARRAY_SIZE(rk3228_code_table), 975 .data_mask = TSADCV3_DATA_MASK, 976 .mode = ADC_INCREMENT, 977 }, 978}; 979 980static const struct rockchip_tsadc_chip rk3368_tsadc_data = { 981 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 982 .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */ 983 .chn_num = 2, /* two channels for tsadc */ 984 985 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 986 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 987 .tshut_temp = 95000, 988 989 .initialize = rk_tsadcv2_initialize, 990 .irq_ack = rk_tsadcv2_irq_ack, 991 .control = rk_tsadcv2_control, 992 .get_temp = rk_tsadcv2_get_temp, 993 .set_alarm_temp = rk_tsadcv2_alarm_temp, 994 .set_tshut_temp = rk_tsadcv2_tshut_temp, 995 .set_tshut_mode = rk_tsadcv2_tshut_mode, 996 997 .table = { 998 .id = rk3368_code_table, 999 .length = ARRAY_SIZE(rk3368_code_table), 1000 .data_mask = TSADCV3_DATA_MASK, 1001 .mode = ADC_INCREMENT, 1002 }, 1003}; 1004 1005static const struct rockchip_tsadc_chip rk3399_tsadc_data = { 1006 .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */ 1007 .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */ 1008 .chn_num = 2, /* two channels for tsadc */ 1009 1010 .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */ 1011 .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */ 1012 .tshut_temp = 95000, 1013 1014 .initialize = rk_tsadcv3_initialize, 1015 .irq_ack = rk_tsadcv3_irq_ack, 1016 .control = rk_tsadcv3_control, 1017 .get_temp = rk_tsadcv2_get_temp, 1018 .set_alarm_temp = rk_tsadcv2_alarm_temp, 1019 .set_tshut_temp = rk_tsadcv2_tshut_temp, 1020 .set_tshut_mode = rk_tsadcv2_tshut_mode, 1021 1022 .table = { 1023 .id = rk3399_code_table, 1024 .length = ARRAY_SIZE(rk3399_code_table), 1025 .data_mask = TSADCV3_DATA_MASK, 1026 .mode = ADC_INCREMENT, 1027 }, 1028}; 1029 1030static const struct of_device_id of_rockchip_thermal_match[] = { 1031 { .compatible = "rockchip,px30-tsadc", 1032 .data = (void *)&px30_tsadc_data, 1033 }, 1034 { 1035 .compatible = "rockchip,rv1108-tsadc", 1036 .data = (void *)&rv1108_tsadc_data, 1037 }, 1038 { 1039 .compatible = "rockchip,rk3228-tsadc", 1040 .data = (void *)&rk3228_tsadc_data, 1041 }, 1042 { 1043 .compatible = "rockchip,rk3288-tsadc", 1044 .data = (void *)&rk3288_tsadc_data, 1045 }, 1046 { 1047 .compatible = "rockchip,rk3328-tsadc", 1048 .data = (void *)&rk3328_tsadc_data, 1049 }, 1050 { 1051 .compatible = "rockchip,rk3366-tsadc", 1052 .data = (void *)&rk3366_tsadc_data, 1053 }, 1054 { 1055 .compatible = "rockchip,rk3368-tsadc", 1056 .data = (void *)&rk3368_tsadc_data, 1057 }, 1058 { 1059 .compatible = "rockchip,rk3399-tsadc", 1060 .data = (void *)&rk3399_tsadc_data, 1061 }, 1062 { /* end */ }, 1063}; 1064MODULE_DEVICE_TABLE(of, of_rockchip_thermal_match); 1065 1066static void 1067rockchip_thermal_toggle_sensor(struct rockchip_thermal_sensor *sensor, bool on) 1068{ 1069 struct thermal_zone_device *tzd = sensor->tzd; 1070 1071 if (on) 1072 thermal_zone_device_enable(tzd); 1073 else 1074 thermal_zone_device_disable(tzd); 1075} 1076 1077static irqreturn_t rockchip_thermal_alarm_irq_thread(int irq, void *dev) 1078{ 1079 struct rockchip_thermal_data *thermal = dev; 1080 int i; 1081 1082 dev_dbg(&thermal->pdev->dev, "thermal alarm\n"); 1083 1084 thermal->chip->irq_ack(thermal->regs); 1085 1086 for (i = 0; i < thermal->chip->chn_num; i++) 1087 thermal_zone_device_update(thermal->sensors[i].tzd, 1088 THERMAL_EVENT_UNSPECIFIED); 1089 1090 return IRQ_HANDLED; 1091} 1092 1093static int rockchip_thermal_set_trips(void *_sensor, int low, int high) 1094{ 1095 struct rockchip_thermal_sensor *sensor = _sensor; 1096 struct rockchip_thermal_data *thermal = sensor->thermal; 1097 const struct rockchip_tsadc_chip *tsadc = thermal->chip; 1098 1099 dev_dbg(&thermal->pdev->dev, "%s: sensor %d: low: %d, high %d\n", 1100 __func__, sensor->id, low, high); 1101 1102 return tsadc->set_alarm_temp(&tsadc->table, 1103 sensor->id, thermal->regs, high); 1104} 1105 1106static int rockchip_thermal_get_temp(void *_sensor, int *out_temp) 1107{ 1108 struct rockchip_thermal_sensor *sensor = _sensor; 1109 struct rockchip_thermal_data *thermal = sensor->thermal; 1110 const struct rockchip_tsadc_chip *tsadc = sensor->thermal->chip; 1111 int retval; 1112 1113 retval = tsadc->get_temp(&tsadc->table, 1114 sensor->id, thermal->regs, out_temp); 1115 dev_dbg(&thermal->pdev->dev, "sensor %d - temp: %d, retval: %d\n", 1116 sensor->id, *out_temp, retval); 1117 1118 return retval; 1119} 1120 1121static const struct thermal_zone_of_device_ops rockchip_of_thermal_ops = { 1122 .get_temp = rockchip_thermal_get_temp, 1123 .set_trips = rockchip_thermal_set_trips, 1124}; 1125 1126static int rockchip_configure_from_dt(struct device *dev, 1127 struct device_node *np, 1128 struct rockchip_thermal_data *thermal) 1129{ 1130 u32 shut_temp, tshut_mode, tshut_polarity; 1131 1132 if (of_property_read_u32(np, "rockchip,hw-tshut-temp", &shut_temp)) { 1133 dev_warn(dev, 1134 "Missing tshut temp property, using default %d\n", 1135 thermal->chip->tshut_temp); 1136 thermal->tshut_temp = thermal->chip->tshut_temp; 1137 } else { 1138 if (shut_temp > INT_MAX) { 1139 dev_err(dev, "Invalid tshut temperature specified: %d\n", 1140 shut_temp); 1141 return -ERANGE; 1142 } 1143 thermal->tshut_temp = shut_temp; 1144 } 1145 1146 if (of_property_read_u32(np, "rockchip,hw-tshut-mode", &tshut_mode)) { 1147 dev_warn(dev, 1148 "Missing tshut mode property, using default (%s)\n", 1149 thermal->chip->tshut_mode == TSHUT_MODE_GPIO ? 1150 "gpio" : "cru"); 1151 thermal->tshut_mode = thermal->chip->tshut_mode; 1152 } else { 1153 thermal->tshut_mode = tshut_mode; 1154 } 1155 1156 if (thermal->tshut_mode > 1) { 1157 dev_err(dev, "Invalid tshut mode specified: %d\n", 1158 thermal->tshut_mode); 1159 return -EINVAL; 1160 } 1161 1162 if (of_property_read_u32(np, "rockchip,hw-tshut-polarity", 1163 &tshut_polarity)) { 1164 dev_warn(dev, 1165 "Missing tshut-polarity property, using default (%s)\n", 1166 thermal->chip->tshut_polarity == TSHUT_LOW_ACTIVE ? 1167 "low" : "high"); 1168 thermal->tshut_polarity = thermal->chip->tshut_polarity; 1169 } else { 1170 thermal->tshut_polarity = tshut_polarity; 1171 } 1172 1173 if (thermal->tshut_polarity > 1) { 1174 dev_err(dev, "Invalid tshut-polarity specified: %d\n", 1175 thermal->tshut_polarity); 1176 return -EINVAL; 1177 } 1178 1179 /* The tsadc wont to handle the error in here since some SoCs didn't 1180 * need this property. 1181 */ 1182 thermal->grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf"); 1183 if (IS_ERR(thermal->grf)) 1184 dev_warn(dev, "Missing rockchip,grf property\n"); 1185 1186 return 0; 1187} 1188 1189static int 1190rockchip_thermal_register_sensor(struct platform_device *pdev, 1191 struct rockchip_thermal_data *thermal, 1192 struct rockchip_thermal_sensor *sensor, 1193 int id) 1194{ 1195 const struct rockchip_tsadc_chip *tsadc = thermal->chip; 1196 int error; 1197 1198 tsadc->set_tshut_mode(id, thermal->regs, thermal->tshut_mode); 1199 1200 error = tsadc->set_tshut_temp(&tsadc->table, id, thermal->regs, 1201 thermal->tshut_temp); 1202 if (error) 1203 dev_err(&pdev->dev, "%s: invalid tshut=%d, error=%d\n", 1204 __func__, thermal->tshut_temp, error); 1205 1206 sensor->thermal = thermal; 1207 sensor->id = id; 1208 sensor->tzd = devm_thermal_zone_of_sensor_register(&pdev->dev, id, 1209 sensor, &rockchip_of_thermal_ops); 1210 if (IS_ERR(sensor->tzd)) { 1211 error = PTR_ERR(sensor->tzd); 1212 dev_err(&pdev->dev, "failed to register sensor %d: %d\n", 1213 id, error); 1214 return error; 1215 } 1216 1217 return 0; 1218} 1219 1220/** 1221 * Reset TSADC Controller, reset all tsadc registers. 1222 * @reset: the reset controller of tsadc 1223 */ 1224static void rockchip_thermal_reset_controller(struct reset_control *reset) 1225{ 1226 reset_control_assert(reset); 1227 usleep_range(10, 20); 1228 reset_control_deassert(reset); 1229} 1230 1231static int rockchip_thermal_probe(struct platform_device *pdev) 1232{ 1233 struct device_node *np = pdev->dev.of_node; 1234 struct rockchip_thermal_data *thermal; 1235 const struct of_device_id *match; 1236 struct resource *res; 1237 int irq; 1238 int i; 1239 int error; 1240 1241 match = of_match_node(of_rockchip_thermal_match, np); 1242 if (!match) 1243 return -ENXIO; 1244 1245 irq = platform_get_irq(pdev, 0); 1246 if (irq < 0) 1247 return -EINVAL; 1248 1249 thermal = devm_kzalloc(&pdev->dev, sizeof(struct rockchip_thermal_data), 1250 GFP_KERNEL); 1251 if (!thermal) 1252 return -ENOMEM; 1253 1254 thermal->pdev = pdev; 1255 1256 thermal->chip = (const struct rockchip_tsadc_chip *)match->data; 1257 if (!thermal->chip) 1258 return -EINVAL; 1259 1260 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1261 thermal->regs = devm_ioremap_resource(&pdev->dev, res); 1262 if (IS_ERR(thermal->regs)) 1263 return PTR_ERR(thermal->regs); 1264 1265 thermal->reset = devm_reset_control_get(&pdev->dev, "tsadc-apb"); 1266 if (IS_ERR(thermal->reset)) { 1267 error = PTR_ERR(thermal->reset); 1268 dev_err(&pdev->dev, "failed to get tsadc reset: %d\n", error); 1269 return error; 1270 } 1271 1272 thermal->clk = devm_clk_get(&pdev->dev, "tsadc"); 1273 if (IS_ERR(thermal->clk)) { 1274 error = PTR_ERR(thermal->clk); 1275 dev_err(&pdev->dev, "failed to get tsadc clock: %d\n", error); 1276 return error; 1277 } 1278 1279 thermal->pclk = devm_clk_get(&pdev->dev, "apb_pclk"); 1280 if (IS_ERR(thermal->pclk)) { 1281 error = PTR_ERR(thermal->pclk); 1282 dev_err(&pdev->dev, "failed to get apb_pclk clock: %d\n", 1283 error); 1284 return error; 1285 } 1286 1287 error = clk_prepare_enable(thermal->clk); 1288 if (error) { 1289 dev_err(&pdev->dev, "failed to enable converter clock: %d\n", 1290 error); 1291 return error; 1292 } 1293 1294 error = clk_prepare_enable(thermal->pclk); 1295 if (error) { 1296 dev_err(&pdev->dev, "failed to enable pclk: %d\n", error); 1297 goto err_disable_clk; 1298 } 1299 1300 rockchip_thermal_reset_controller(thermal->reset); 1301 1302 error = rockchip_configure_from_dt(&pdev->dev, np, thermal); 1303 if (error) { 1304 dev_err(&pdev->dev, "failed to parse device tree data: %d\n", 1305 error); 1306 goto err_disable_pclk; 1307 } 1308 1309 thermal->chip->initialize(thermal->grf, thermal->regs, 1310 thermal->tshut_polarity); 1311 1312 for (i = 0; i < thermal->chip->chn_num; i++) { 1313 error = rockchip_thermal_register_sensor(pdev, thermal, 1314 &thermal->sensors[i], 1315 thermal->chip->chn_id[i]); 1316 if (error) { 1317 dev_err(&pdev->dev, 1318 "failed to register sensor[%d] : error = %d\n", 1319 i, error); 1320 goto err_disable_pclk; 1321 } 1322 } 1323 1324 error = devm_request_threaded_irq(&pdev->dev, irq, NULL, 1325 &rockchip_thermal_alarm_irq_thread, 1326 IRQF_ONESHOT, 1327 "rockchip_thermal", thermal); 1328 if (error) { 1329 dev_err(&pdev->dev, 1330 "failed to request tsadc irq: %d\n", error); 1331 goto err_disable_pclk; 1332 } 1333 1334 thermal->chip->control(thermal->regs, true); 1335 1336 for (i = 0; i < thermal->chip->chn_num; i++) { 1337 rockchip_thermal_toggle_sensor(&thermal->sensors[i], true); 1338 thermal->sensors[i].tzd->tzp->no_hwmon = false; 1339 error = thermal_add_hwmon_sysfs(thermal->sensors[i].tzd); 1340 if (error) 1341 dev_warn(&pdev->dev, 1342 "failed to register sensor %d with hwmon: %d\n", 1343 i, error); 1344 } 1345 1346 platform_set_drvdata(pdev, thermal); 1347 1348 return 0; 1349 1350err_disable_pclk: 1351 clk_disable_unprepare(thermal->pclk); 1352err_disable_clk: 1353 clk_disable_unprepare(thermal->clk); 1354 1355 return error; 1356} 1357 1358static int rockchip_thermal_remove(struct platform_device *pdev) 1359{ 1360 struct rockchip_thermal_data *thermal = platform_get_drvdata(pdev); 1361 int i; 1362 1363 for (i = 0; i < thermal->chip->chn_num; i++) { 1364 struct rockchip_thermal_sensor *sensor = &thermal->sensors[i]; 1365 1366 thermal_remove_hwmon_sysfs(sensor->tzd); 1367 rockchip_thermal_toggle_sensor(sensor, false); 1368 } 1369 1370 thermal->chip->control(thermal->regs, false); 1371 1372 clk_disable_unprepare(thermal->pclk); 1373 clk_disable_unprepare(thermal->clk); 1374 1375 return 0; 1376} 1377 1378static int __maybe_unused rockchip_thermal_suspend(struct device *dev) 1379{ 1380 struct rockchip_thermal_data *thermal = dev_get_drvdata(dev); 1381 int i; 1382 1383 for (i = 0; i < thermal->chip->chn_num; i++) 1384 rockchip_thermal_toggle_sensor(&thermal->sensors[i], false); 1385 1386 thermal->chip->control(thermal->regs, false); 1387 1388 clk_disable(thermal->pclk); 1389 clk_disable(thermal->clk); 1390 1391 pinctrl_pm_select_sleep_state(dev); 1392 1393 return 0; 1394} 1395 1396static int __maybe_unused rockchip_thermal_resume(struct device *dev) 1397{ 1398 struct rockchip_thermal_data *thermal = dev_get_drvdata(dev); 1399 int i; 1400 int error; 1401 1402 error = clk_enable(thermal->clk); 1403 if (error) 1404 return error; 1405 1406 error = clk_enable(thermal->pclk); 1407 if (error) { 1408 clk_disable(thermal->clk); 1409 return error; 1410 } 1411 1412 rockchip_thermal_reset_controller(thermal->reset); 1413 1414 thermal->chip->initialize(thermal->grf, thermal->regs, 1415 thermal->tshut_polarity); 1416 1417 for (i = 0; i < thermal->chip->chn_num; i++) { 1418 int id = thermal->sensors[i].id; 1419 1420 thermal->chip->set_tshut_mode(id, thermal->regs, 1421 thermal->tshut_mode); 1422 1423 error = thermal->chip->set_tshut_temp(&thermal->chip->table, 1424 id, thermal->regs, 1425 thermal->tshut_temp); 1426 if (error) 1427 dev_err(dev, "%s: invalid tshut=%d, error=%d\n", 1428 __func__, thermal->tshut_temp, error); 1429 } 1430 1431 thermal->chip->control(thermal->regs, true); 1432 1433 for (i = 0; i < thermal->chip->chn_num; i++) 1434 rockchip_thermal_toggle_sensor(&thermal->sensors[i], true); 1435 1436 pinctrl_pm_select_default_state(dev); 1437 1438 return 0; 1439} 1440 1441static SIMPLE_DEV_PM_OPS(rockchip_thermal_pm_ops, 1442 rockchip_thermal_suspend, rockchip_thermal_resume); 1443 1444static struct platform_driver rockchip_thermal_driver = { 1445 .driver = { 1446 .name = "rockchip-thermal", 1447 .pm = &rockchip_thermal_pm_ops, 1448 .of_match_table = of_rockchip_thermal_match, 1449 }, 1450 .probe = rockchip_thermal_probe, 1451 .remove = rockchip_thermal_remove, 1452}; 1453 1454module_platform_driver(rockchip_thermal_driver); 1455 1456MODULE_DESCRIPTION("ROCKCHIP THERMAL Driver"); 1457MODULE_AUTHOR("Rockchip, Inc."); 1458MODULE_LICENSE("GPL v2"); 1459MODULE_ALIAS("platform:rockchip-thermal"); 1460