1// SPDX-License-Identifier: GPL-2.0 2/* Copyright (c) 2018, Broadcom */ 3 4/* 5 * This module contains USB PHY initialization for power up and S3 resume 6 * for newer Synopsys based USB hardware first used on the bcm7216. 7 */ 8 9#include <linux/delay.h> 10#include <linux/io.h> 11 12#include <linux/soc/brcmstb/brcmstb.h> 13#include "phy-brcm-usb-init.h" 14 15#define PHY_LOCK_TIMEOUT_MS 200 16 17/* Register definitions for syscon piarbctl registers */ 18#define PIARBCTL_CAM 0x00 19#define PIARBCTL_SPLITTER 0x04 20#define PIARBCTL_MISC 0x08 21#define PIARBCTL_MISC_SECURE_MASK 0x80000000 22#define PIARBCTL_MISC_USB_SELECT_MASK 0x40000000 23#define PIARBCTL_MISC_USB_4G_SDRAM_MASK 0x20000000 24#define PIARBCTL_MISC_USB_PRIORITY_MASK 0x000f0000 25#define PIARBCTL_MISC_USB_MEM_PAGE_MASK 0x0000f000 26#define PIARBCTL_MISC_CAM1_MEM_PAGE_MASK 0x00000f00 27#define PIARBCTL_MISC_CAM0_MEM_PAGE_MASK 0x000000f0 28#define PIARBCTL_MISC_SATA_PRIORITY_MASK 0x0000000f 29 30#define PIARBCTL_MISC_USB_ONLY_MASK \ 31 (PIARBCTL_MISC_USB_SELECT_MASK | \ 32 PIARBCTL_MISC_USB_4G_SDRAM_MASK | \ 33 PIARBCTL_MISC_USB_PRIORITY_MASK | \ 34 PIARBCTL_MISC_USB_MEM_PAGE_MASK) 35 36/* Register definitions for the USB CTRL block */ 37#define USB_CTRL_SETUP 0x00 38#define USB_CTRL_SETUP_STRAP_IPP_SEL_MASK 0x02000000 39#define USB_CTRL_SETUP_SCB2_EN_MASK 0x00008000 40#define USB_CTRL_SETUP_tca_drv_sel_MASK 0x01000000 41#define USB_CTRL_SETUP_SCB1_EN_MASK 0x00004000 42#define USB_CTRL_SETUP_SOFT_SHUTDOWN_MASK 0x00000200 43#define USB_CTRL_SETUP_IPP_MASK 0x00000020 44#define USB_CTRL_SETUP_IOC_MASK 0x00000010 45#define USB_CTRL_USB_PM 0x04 46#define USB_CTRL_USB_PM_USB_PWRDN_MASK 0x80000000 47#define USB_CTRL_USB_PM_SOFT_RESET_MASK 0x40000000 48#define USB_CTRL_USB_PM_BDC_SOFT_RESETB_MASK 0x00800000 49#define USB_CTRL_USB_PM_XHC_SOFT_RESETB_MASK 0x00400000 50#define USB_CTRL_USB_PM_STATUS 0x08 51#define USB_CTRL_USB_DEVICE_CTL1 0x10 52#define USB_CTRL_USB_DEVICE_CTL1_PORT_MODE_MASK 0x00000003 53#define USB_CTRL_TEST_PORT_CTL 0x30 54#define USB_CTRL_TEST_PORT_CTL_TPOUT_SEL_MASK 0x000000ff 55#define USB_CTRL_TEST_PORT_CTL_TPOUT_SEL_PME_GEN_MASK 0x0000002e 56#define USB_CTRL_TP_DIAG1 0x34 57#define USB_CTLR_TP_DIAG1_wake_MASK 0x00000002 58#define USB_CTRL_CTLR_CSHCR 0x50 59#define USB_CTRL_CTLR_CSHCR_ctl_pme_en_MASK 0x00040000 60 61/* Register definitions for the USB_PHY block in 7211b0 */ 62#define USB_PHY_PLL_CTL 0x00 63#define USB_PHY_PLL_CTL_PLL_RESETB_MASK 0x40000000 64#define USB_PHY_PLL_LDO_CTL 0x08 65#define USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK 0x00000004 66#define USB_PHY_PLL_LDO_CTL_AFE_LDO_PWRDWNB_MASK 0x00000002 67#define USB_PHY_PLL_LDO_CTL_AFE_BG_PWRDWNB_MASK 0x00000001 68#define USB_PHY_UTMI_CTL_1 0x04 69#define USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK 0x00000800 70#define USB_PHY_UTMI_CTL_1_PHY_MODE_MASK 0x0000000c 71#define USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT 2 72#define USB_PHY_IDDQ 0x1c 73#define USB_PHY_IDDQ_phy_iddq_MASK 0x00000001 74#define USB_PHY_STATUS 0x20 75#define USB_PHY_STATUS_pll_lock_MASK 0x00000001 76 77/* Register definitions for the MDIO registers in the DWC2 block of 78 * the 7211b0. 79 * NOTE: The PHY's MDIO registers are only accessible through the 80 * legacy DesignWare USB controller even though it's not being used. 81 */ 82#define USB_GMDIOCSR 0 83#define USB_GMDIOGEN 4 84 85/* Register definitions for the BDC EC block in 7211b0 */ 86#define BDC_EC_AXIRDA 0x0c 87#define BDC_EC_AXIRDA_RTS_MASK 0xf0000000 88#define BDC_EC_AXIRDA_RTS_SHIFT 28 89 90 91static void usb_mdio_write_7211b0(struct brcm_usb_init_params *params, 92 uint8_t addr, uint16_t data) 93{ 94 void __iomem *usb_mdio = params->regs[BRCM_REGS_USB_MDIO]; 95 96 addr &= 0x1f; /* 5-bit address */ 97 brcm_usb_writel(0xffffffff, usb_mdio + USB_GMDIOGEN); 98 while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31)) 99 ; 100 brcm_usb_writel(0x59020000 | (addr << 18) | data, 101 usb_mdio + USB_GMDIOGEN); 102 while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31)) 103 ; 104 brcm_usb_writel(0x00000000, usb_mdio + USB_GMDIOGEN); 105 while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31)) 106 ; 107} 108 109static uint16_t __maybe_unused usb_mdio_read_7211b0( 110 struct brcm_usb_init_params *params, uint8_t addr) 111{ 112 void __iomem *usb_mdio = params->regs[BRCM_REGS_USB_MDIO]; 113 114 addr &= 0x1f; /* 5-bit address */ 115 brcm_usb_writel(0xffffffff, usb_mdio + USB_GMDIOGEN); 116 while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31)) 117 ; 118 brcm_usb_writel(0x69020000 | (addr << 18), usb_mdio + USB_GMDIOGEN); 119 while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31)) 120 ; 121 brcm_usb_writel(0x00000000, usb_mdio + USB_GMDIOGEN); 122 while (brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & (1<<31)) 123 ; 124 return brcm_usb_readl(usb_mdio + USB_GMDIOCSR) & 0xffff; 125} 126 127static void usb2_eye_fix_7211b0(struct brcm_usb_init_params *params) 128{ 129 /* select bank */ 130 usb_mdio_write_7211b0(params, 0x1f, 0x80a0); 131 132 /* Set the eye */ 133 usb_mdio_write_7211b0(params, 0x0a, 0xc6a0); 134} 135 136static void xhci_soft_reset(struct brcm_usb_init_params *params, 137 int on_off) 138{ 139 void __iomem *ctrl = params->regs[BRCM_REGS_CTRL]; 140 141 /* Assert reset */ 142 if (on_off) 143 USB_CTRL_UNSET(ctrl, USB_PM, XHC_SOFT_RESETB); 144 /* De-assert reset */ 145 else 146 USB_CTRL_SET(ctrl, USB_PM, XHC_SOFT_RESETB); 147} 148 149static void usb_init_ipp(struct brcm_usb_init_params *params) 150{ 151 void __iomem *ctrl = params->regs[BRCM_REGS_CTRL]; 152 u32 reg; 153 u32 orig_reg; 154 155 pr_debug("%s\n", __func__); 156 157 orig_reg = reg = brcm_usb_readl(USB_CTRL_REG(ctrl, SETUP)); 158 if (params->ipp != 2) 159 /* override ipp strap pin (if it exits) */ 160 reg &= ~(USB_CTRL_MASK(SETUP, STRAP_IPP_SEL)); 161 162 /* Override the default OC and PP polarity */ 163 reg &= ~(USB_CTRL_MASK(SETUP, IPP) | USB_CTRL_MASK(SETUP, IOC)); 164 if (params->ioc) 165 reg |= USB_CTRL_MASK(SETUP, IOC); 166 if (params->ipp == 1) 167 reg |= USB_CTRL_MASK(SETUP, IPP); 168 brcm_usb_writel(reg, USB_CTRL_REG(ctrl, SETUP)); 169 170 /* 171 * If we're changing IPP, make sure power is off long enough 172 * to turn off any connected devices. 173 */ 174 if ((reg ^ orig_reg) & USB_CTRL_MASK(SETUP, IPP)) 175 msleep(50); 176} 177 178static void syscon_piarbctl_init(struct regmap *rmap) 179{ 180 /* Switch from legacy USB OTG controller to new STB USB controller */ 181 regmap_update_bits(rmap, PIARBCTL_MISC, PIARBCTL_MISC_USB_ONLY_MASK, 182 PIARBCTL_MISC_USB_SELECT_MASK | 183 PIARBCTL_MISC_USB_4G_SDRAM_MASK); 184} 185 186static void usb_init_common(struct brcm_usb_init_params *params) 187{ 188 u32 reg; 189 void __iomem *ctrl = params->regs[BRCM_REGS_CTRL]; 190 191 pr_debug("%s\n", __func__); 192 193 USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN); 194 /* 1 millisecond - for USB clocks to settle down */ 195 usleep_range(1000, 2000); 196 197 if (USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE)) { 198 reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1)); 199 reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE); 200 reg |= params->mode; 201 brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1)); 202 } 203 switch (params->mode) { 204 case USB_CTLR_MODE_HOST: 205 USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB); 206 break; 207 default: 208 USB_CTRL_UNSET(ctrl, USB_PM, BDC_SOFT_RESETB); 209 USB_CTRL_SET(ctrl, USB_PM, BDC_SOFT_RESETB); 210 break; 211 } 212} 213 214static void usb_wake_enable_7211b0(struct brcm_usb_init_params *params, 215 bool enable) 216{ 217 void __iomem *ctrl = params->regs[BRCM_REGS_CTRL]; 218 219 if (enable) 220 USB_CTRL_SET(ctrl, CTLR_CSHCR, ctl_pme_en); 221 else 222 USB_CTRL_UNSET(ctrl, CTLR_CSHCR, ctl_pme_en); 223} 224 225static void usb_init_common_7211b0(struct brcm_usb_init_params *params) 226{ 227 void __iomem *ctrl = params->regs[BRCM_REGS_CTRL]; 228 void __iomem *usb_phy = params->regs[BRCM_REGS_USB_PHY]; 229 void __iomem *bdc_ec = params->regs[BRCM_REGS_BDC_EC]; 230 int timeout_ms = PHY_LOCK_TIMEOUT_MS; 231 u32 reg; 232 233 if (params->syscon_piarbctl) 234 syscon_piarbctl_init(params->syscon_piarbctl); 235 236 USB_CTRL_UNSET(ctrl, USB_PM, USB_PWRDN); 237 238 usb_wake_enable_7211b0(params, false); 239 if (!params->wake_enabled) { 240 241 /* undo possible suspend settings */ 242 brcm_usb_writel(0, usb_phy + USB_PHY_IDDQ); 243 reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_CTL); 244 reg |= USB_PHY_PLL_CTL_PLL_RESETB_MASK; 245 brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_CTL); 246 247 /* temporarily enable FSM so PHY comes up properly */ 248 reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1); 249 reg |= USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK; 250 brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1); 251 } 252 253 /* Init the PHY */ 254 reg = USB_PHY_PLL_LDO_CTL_AFE_CORERDY_MASK | 255 USB_PHY_PLL_LDO_CTL_AFE_LDO_PWRDWNB_MASK | 256 USB_PHY_PLL_LDO_CTL_AFE_BG_PWRDWNB_MASK; 257 brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_LDO_CTL); 258 259 /* wait for lock */ 260 while (timeout_ms-- > 0) { 261 reg = brcm_usb_readl(usb_phy + USB_PHY_STATUS); 262 if (reg & USB_PHY_STATUS_pll_lock_MASK) 263 break; 264 usleep_range(1000, 2000); 265 } 266 267 /* Set the PHY_MODE */ 268 reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1); 269 reg &= ~USB_PHY_UTMI_CTL_1_PHY_MODE_MASK; 270 reg |= params->mode << USB_PHY_UTMI_CTL_1_PHY_MODE_SHIFT; 271 brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1); 272 273 usb_init_common(params); 274 275 /* 276 * The BDC controller will get occasional failures with 277 * the default "Read Transaction Size" of 6 (1024 bytes). 278 * Set it to 4 (256 bytes). 279 */ 280 if ((params->mode != USB_CTLR_MODE_HOST) && bdc_ec) { 281 reg = brcm_usb_readl(bdc_ec + BDC_EC_AXIRDA); 282 reg &= ~BDC_EC_AXIRDA_RTS_MASK; 283 reg |= (0x4 << BDC_EC_AXIRDA_RTS_SHIFT); 284 brcm_usb_writel(reg, bdc_ec + BDC_EC_AXIRDA); 285 } 286 287 /* 288 * Disable FSM, otherwise the PHY will auto suspend when no 289 * device is connected and will be reset on resume. 290 */ 291 reg = brcm_usb_readl(usb_phy + USB_PHY_UTMI_CTL_1); 292 reg &= ~USB_PHY_UTMI_CTL_1_POWER_UP_FSM_EN_MASK; 293 brcm_usb_writel(reg, usb_phy + USB_PHY_UTMI_CTL_1); 294 295 usb2_eye_fix_7211b0(params); 296} 297 298static void usb_init_xhci(struct brcm_usb_init_params *params) 299{ 300 pr_debug("%s\n", __func__); 301 302 xhci_soft_reset(params, 0); 303} 304 305static void usb_uninit_common(struct brcm_usb_init_params *params) 306{ 307 void __iomem *ctrl = params->regs[BRCM_REGS_CTRL]; 308 309 pr_debug("%s\n", __func__); 310 311 USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN); 312 313} 314 315static void usb_uninit_common_7211b0(struct brcm_usb_init_params *params) 316{ 317 void __iomem *ctrl = params->regs[BRCM_REGS_CTRL]; 318 void __iomem *usb_phy = params->regs[BRCM_REGS_USB_PHY]; 319 u32 reg; 320 321 pr_debug("%s\n", __func__); 322 323 if (params->wake_enabled) { 324 USB_CTRL_SET(ctrl, TEST_PORT_CTL, TPOUT_SEL_PME_GEN); 325 usb_wake_enable_7211b0(params, true); 326 } else { 327 USB_CTRL_SET(ctrl, USB_PM, USB_PWRDN); 328 brcm_usb_writel(0, usb_phy + USB_PHY_PLL_LDO_CTL); 329 reg = brcm_usb_readl(usb_phy + USB_PHY_PLL_CTL); 330 reg &= ~USB_PHY_PLL_CTL_PLL_RESETB_MASK; 331 brcm_usb_writel(reg, usb_phy + USB_PHY_PLL_CTL); 332 brcm_usb_writel(USB_PHY_IDDQ_phy_iddq_MASK, 333 usb_phy + USB_PHY_IDDQ); 334 } 335 336} 337 338static void usb_uninit_xhci(struct brcm_usb_init_params *params) 339{ 340 341 pr_debug("%s\n", __func__); 342 343 if (!params->wake_enabled) 344 xhci_soft_reset(params, 1); 345} 346 347static int usb_get_dual_select(struct brcm_usb_init_params *params) 348{ 349 void __iomem *ctrl = params->regs[BRCM_REGS_CTRL]; 350 u32 reg = 0; 351 352 pr_debug("%s\n", __func__); 353 354 reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1)); 355 reg &= USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE); 356 return reg; 357} 358 359static void usb_set_dual_select(struct brcm_usb_init_params *params, int mode) 360{ 361 void __iomem *ctrl = params->regs[BRCM_REGS_CTRL]; 362 u32 reg; 363 364 pr_debug("%s\n", __func__); 365 366 reg = brcm_usb_readl(USB_CTRL_REG(ctrl, USB_DEVICE_CTL1)); 367 reg &= ~USB_CTRL_MASK(USB_DEVICE_CTL1, PORT_MODE); 368 reg |= mode; 369 brcm_usb_writel(reg, USB_CTRL_REG(ctrl, USB_DEVICE_CTL1)); 370} 371 372static const struct brcm_usb_init_ops bcm7216_ops = { 373 .init_ipp = usb_init_ipp, 374 .init_common = usb_init_common, 375 .init_xhci = usb_init_xhci, 376 .uninit_common = usb_uninit_common, 377 .uninit_xhci = usb_uninit_xhci, 378 .get_dual_select = usb_get_dual_select, 379 .set_dual_select = usb_set_dual_select, 380}; 381 382static const struct brcm_usb_init_ops bcm7211b0_ops = { 383 .init_ipp = usb_init_ipp, 384 .init_common = usb_init_common_7211b0, 385 .init_xhci = usb_init_xhci, 386 .uninit_common = usb_uninit_common_7211b0, 387 .uninit_xhci = usb_uninit_xhci, 388 .get_dual_select = usb_get_dual_select, 389 .set_dual_select = usb_set_dual_select, 390}; 391 392void brcm_usb_dvr_init_7216(struct brcm_usb_init_params *params) 393{ 394 395 pr_debug("%s\n", __func__); 396 397 params->family_name = "7216"; 398 params->ops = &bcm7216_ops; 399} 400 401void brcm_usb_dvr_init_7211b0(struct brcm_usb_init_params *params) 402{ 403 404 pr_debug("%s\n", __func__); 405 406 params->family_name = "7211"; 407 params->ops = &bcm7211b0_ops; 408 params->suspend_with_clocks = true; 409} 410