1/* SPDX-License-Identifier: GPL-2.0-or-later */
2/*
3	Copyright (C) 2004 - 2009 Ivo van Doorn <IvDoorn@gmail.com>
4	<http://rt2x00.serialmonkey.com>
5
6 */
7
8/*
9	Module: rt2x00dump
10	Abstract:
11		Data structures for the rt2x00debug & userspace.
12
13		The declarations in this file can be used by both rt2x00
14		and userspace and therefore should be kept together in
15		this file.
16 */
17
18#ifndef RT2X00DUMP_H
19#define RT2X00DUMP_H
20
21/**
22 * DOC: Introduction
23 *
24 * This header is intended to be exported to userspace,
25 * to make the structures and enumerations available to userspace
26 * applications. This means that all data types should be exportable.
27 *
28 * When rt2x00 is compiled with debugfs support enabled,
29 * it is possible to capture all data coming in and out of the device
30 * by reading the frame dump file. This file can have only a single reader.
31 * The following frames will be reported:
32 *   - All incoming frames (rx)
33 *   - All outgoing frames (tx, including beacon and atim)
34 *   - All completed frames (txdone including atim)
35 *
36 * The data is send to the file using the following format:
37 *
38 *   [rt2x00dump header][hardware descriptor][ieee802.11 frame]
39 *
40 * rt2x00dump header: The description of the dumped frame, as well as
41 *	additional information useful for debugging. See &rt2x00dump_hdr.
42 * hardware descriptor: Descriptor that was used to receive or transmit
43 *	the frame.
44 * ieee802.11 frame: The actual frame that was received or transmitted.
45 */
46
47/**
48 * enum rt2x00_dump_type - Frame type
49 *
50 * These values are used for the @type member of &rt2x00dump_hdr.
51 * @DUMP_FRAME_RXDONE: This frame has been received by the hardware.
52 * @DUMP_FRAME_TX: This frame is queued for transmission to the hardware.
53 * @DUMP_FRAME_TXDONE: This frame indicates the device has handled
54 *	the tx event which has either succeeded or failed. A frame
55 *	with this type should also have been reported with as a
56 *	%DUMP_FRAME_TX frame.
57 * @DUMP_FRAME_BEACON: This beacon frame is queued for transmission to the
58 *	hardware.
59 */
60enum rt2x00_dump_type {
61	DUMP_FRAME_RXDONE = 1,
62	DUMP_FRAME_TX = 2,
63	DUMP_FRAME_TXDONE = 3,
64	DUMP_FRAME_BEACON = 4,
65};
66
67/**
68 * struct rt2x00dump_hdr - Dump frame header
69 *
70 * Each frame dumped to the debugfs file starts with this header
71 * attached. This header contains the description of the actual
72 * frame which was dumped.
73 *
74 * New fields inside the structure must be appended to the end of
75 * the structure. This way userspace tools compiled for earlier
76 * header versions can still correctly handle the frame dump
77 * (although they will not handle all data passed to them in the dump).
78 *
79 * @version: Header version should always be set to %DUMP_HEADER_VERSION.
80 *	This field must be checked by userspace to determine if it can
81 *	handle this frame.
82 * @header_length: The length of the &rt2x00dump_hdr structure. This is
83 *	used for compatibility reasons so userspace can easily determine
84 *	the location of the next field in the dump.
85 * @desc_length: The length of the device descriptor.
86 * @data_length: The length of the frame data (including the ieee802.11 header.
87 * @chip_rt: RT chipset
88 * @chip_rf: RF chipset
89 * @chip_rev: Chipset revision
90 * @type: The frame type (&rt2x00_dump_type)
91 * @queue_index: The index number of the data queue.
92 * @entry_index: The index number of the entry inside the data queue.
93 * @timestamp_sec: Timestamp - seconds
94 * @timestamp_usec: Timestamp - microseconds
95 */
96struct rt2x00dump_hdr {
97	__le32 version;
98#define DUMP_HEADER_VERSION	3
99
100	__le32 header_length;
101	__le32 desc_length;
102	__le32 data_length;
103
104	__le16 chip_rt;
105	__le16 chip_rf;
106	__le16 chip_rev;
107
108	__le16 type;
109	__u8 queue_index;
110	__u8 entry_index;
111
112	__le32 timestamp_sec;
113	__le32 timestamp_usec;
114};
115
116#endif /* RT2X00DUMP_H */
117