1// SPDX-License-Identifier: GPL-2.0
2/* $Date: 2005/11/12 02:13:49 $ $RCSfile: my3126.c,v $ $Revision: 1.15 $ */
3#include "cphy.h"
4#include "elmer0.h"
5#include "suni1x10gexp_regs.h"
6
7/* Port Reset */
8static int my3126_reset(struct cphy *cphy, int wait)
9{
10	/*
11	 * This can be done through registers.  It is not required since
12	 * a full chip reset is used.
13	 */
14	return 0;
15}
16
17static int my3126_interrupt_enable(struct cphy *cphy)
18{
19	schedule_delayed_work(&cphy->phy_update, HZ/30);
20	t1_tpi_read(cphy->adapter, A_ELMER0_GPO, &cphy->elmer_gpo);
21	return 0;
22}
23
24static int my3126_interrupt_disable(struct cphy *cphy)
25{
26	cancel_delayed_work_sync(&cphy->phy_update);
27	return 0;
28}
29
30static int my3126_interrupt_clear(struct cphy *cphy)
31{
32	return 0;
33}
34
35#define OFFSET(REG_ADDR)    (REG_ADDR << 2)
36
37static int my3126_interrupt_handler(struct cphy *cphy)
38{
39	u32 val;
40	u16 val16;
41	u16 status;
42	u32 act_count;
43	adapter_t *adapter;
44	adapter = cphy->adapter;
45
46	if (cphy->count == 50) {
47		cphy_mdio_read(cphy, MDIO_MMD_PMAPMD, MDIO_STAT1, &val);
48		val16 = (u16) val;
49		status = cphy->bmsr ^ val16;
50
51		if (status & MDIO_STAT1_LSTATUS)
52			t1_link_changed(adapter, 0);
53		cphy->bmsr = val16;
54
55		/* We have only enabled link change interrupts so it
56		   must be that
57		 */
58		cphy->count = 0;
59	}
60
61	t1_tpi_write(adapter, OFFSET(SUNI1x10GEXP_REG_MSTAT_CONTROL),
62		SUNI1x10GEXP_BITMSK_MSTAT_SNAP);
63	t1_tpi_read(adapter,
64		OFFSET(SUNI1x10GEXP_REG_MSTAT_COUNTER_1_LOW), &act_count);
65	t1_tpi_read(adapter,
66		OFFSET(SUNI1x10GEXP_REG_MSTAT_COUNTER_33_LOW), &val);
67	act_count += val;
68
69	/* Populate elmer_gpo with the register value */
70	t1_tpi_read(adapter, A_ELMER0_GPO, &val);
71	cphy->elmer_gpo = val;
72
73	if ( (val & (1 << 8)) || (val & (1 << 19)) ||
74	     (cphy->act_count == act_count) || cphy->act_on ) {
75		if (is_T2(adapter))
76			val |= (1 << 9);
77		else if (t1_is_T1B(adapter))
78			val |= (1 << 20);
79		cphy->act_on = 0;
80	} else {
81		if (is_T2(adapter))
82			val &= ~(1 << 9);
83		else if (t1_is_T1B(adapter))
84			val &= ~(1 << 20);
85		cphy->act_on = 1;
86	}
87
88	t1_tpi_write(adapter, A_ELMER0_GPO, val);
89
90	cphy->elmer_gpo = val;
91	cphy->act_count = act_count;
92	cphy->count++;
93
94	return cphy_cause_link_change;
95}
96
97static void my3126_poll(struct work_struct *work)
98{
99	struct cphy *cphy = container_of(work, struct cphy, phy_update.work);
100
101	my3126_interrupt_handler(cphy);
102}
103
104static int my3126_set_loopback(struct cphy *cphy, int on)
105{
106	return 0;
107}
108
109/* To check the activity LED */
110static int my3126_get_link_status(struct cphy *cphy,
111			int *link_ok, int *speed, int *duplex, int *fc)
112{
113	u32 val;
114	u16 val16;
115	adapter_t *adapter;
116
117	adapter = cphy->adapter;
118	cphy_mdio_read(cphy, MDIO_MMD_PMAPMD, MDIO_STAT1, &val);
119	val16 = (u16) val;
120
121	/* Populate elmer_gpo with the register value */
122	t1_tpi_read(adapter, A_ELMER0_GPO, &val);
123	cphy->elmer_gpo = val;
124
125	*link_ok = (val16 & MDIO_STAT1_LSTATUS);
126
127	if (*link_ok) {
128		/* Turn on the LED. */
129		if (is_T2(adapter))
130			 val &= ~(1 << 8);
131		else if (t1_is_T1B(adapter))
132			 val &= ~(1 << 19);
133	} else {
134		/* Turn off the LED. */
135		if (is_T2(adapter))
136			 val |= (1 << 8);
137		else if (t1_is_T1B(adapter))
138			 val |= (1 << 19);
139	}
140
141	t1_tpi_write(adapter, A_ELMER0_GPO, val);
142	cphy->elmer_gpo = val;
143	*speed = SPEED_10000;
144	*duplex = DUPLEX_FULL;
145
146	/* need to add flow control */
147	if (fc)
148		*fc = PAUSE_RX | PAUSE_TX;
149
150	return 0;
151}
152
153static void my3126_destroy(struct cphy *cphy)
154{
155	kfree(cphy);
156}
157
158static const struct cphy_ops my3126_ops = {
159	.destroy		= my3126_destroy,
160	.reset			= my3126_reset,
161	.interrupt_enable	= my3126_interrupt_enable,
162	.interrupt_disable	= my3126_interrupt_disable,
163	.interrupt_clear	= my3126_interrupt_clear,
164	.interrupt_handler	= my3126_interrupt_handler,
165	.get_link_status	= my3126_get_link_status,
166	.set_loopback		= my3126_set_loopback,
167	.mmds			= (MDIO_DEVS_PMAPMD | MDIO_DEVS_PCS |
168				   MDIO_DEVS_PHYXS),
169};
170
171static struct cphy *my3126_phy_create(struct net_device *dev,
172			int phy_addr, const struct mdio_ops *mdio_ops)
173{
174	struct cphy *cphy = kzalloc(sizeof (*cphy), GFP_KERNEL);
175
176	if (!cphy)
177		return NULL;
178
179	cphy_init(cphy, dev, phy_addr, &my3126_ops, mdio_ops);
180	INIT_DELAYED_WORK(&cphy->phy_update, my3126_poll);
181	cphy->bmsr = 0;
182
183	return cphy;
184}
185
186/* Chip Reset */
187static int my3126_phy_reset(adapter_t * adapter)
188{
189	u32 val;
190
191	t1_tpi_read(adapter, A_ELMER0_GPO, &val);
192	val &= ~4;
193	t1_tpi_write(adapter, A_ELMER0_GPO, val);
194	msleep(100);
195
196	t1_tpi_write(adapter, A_ELMER0_GPO, val | 4);
197	msleep(1000);
198
199	/* Now lets enable the Laser. Delay 100us */
200	t1_tpi_read(adapter, A_ELMER0_GPO, &val);
201	val |= 0x8000;
202	t1_tpi_write(adapter, A_ELMER0_GPO, val);
203	udelay(100);
204	return 0;
205}
206
207const struct gphy t1_my3126_ops = {
208	.create = my3126_phy_create,
209	.reset = my3126_phy_reset
210};
211