xref: /kernel/linux/linux-5.10/drivers/media/usb/gspca/pac7302.c

// SPDX-License-Identifier: GPL-2.0-or-later
/*
 * Pixart PAC7302 driver
 *
 * Copyright (C) 2008-2012 Jean-Francois Moine <http://moinejf.free.fr>
 * Copyright (C) 2005 Thomas Kaiser thomas@kaiser-linux.li
 *
 * Separated from Pixart PAC7311 library by Márton Németh
 * Camera button input handling by Márton Németh <nm127@freemail.hu>
 * Copyright (C) 2009-2010 Márton Németh <nm127@freemail.hu>
 */

/*
 * Some documentation about various registers as determined by trial and error.
 *
 * Register page 0:
 *
 * Address	Description
 * 0x01		Red balance control
 * 0x02		Green balance control
 * 0x03		Blue balance control
 *		     The Windows driver uses a quadratic approach to map
 *		     the settable values (0-200) on register values:
 *		     min=0x20, default=0x40, max=0x80
 * 0x0f-0x20	Color and saturation control
 * 0xa2-0xab	Brightness, contrast and gamma control
 * 0xb6		Sharpness control (bits 0-4)
 *
 * Register page 1:
 *
 * Address	Description
 * 0x78		Global control, bit 6 controls the LED (inverted)
 * 0x80		Compression balance, 2 interesting settings:
 *		0x0f Default
 *		0x50 Values >= this switch the camera to a lower compression,
 *		     using the same table for both luminance and chrominance.
 *		     This gives a sharper picture. Only usable when running
 *		     at < 15 fps! Note currently the driver does not use this
 *		     as the quality gain is small and the generated JPG-s are
 *		     only understood by v4l-utils >= 0.8.9
 *
 * Register page 3:
 *
 * Address	Description
 * 0x02		Clock divider 3-63, fps = 90 / val. Must be a multiple of 3 on
 *		the 7302, so one of 3, 6, 9, ..., except when between 6 and 12?
 * 0x03		Variable framerate ctrl reg2==3: 0 -> ~30 fps, 255 -> ~22fps
 * 0x04		Another var framerate ctrl reg2==3, reg3==0: 0 -> ~30 fps,
 *		63 -> ~27 fps, the 2 msb's must always be 1 !!
 * 0x05		Another var framerate ctrl reg2==3, reg3==0, reg4==0xc0:
 *		1 -> ~30 fps, 2 -> ~20 fps
 * 0x0e		Exposure bits 0-7, 0-448, 0 = use full frame time
 * 0x0f		Exposure bit 8, 0-448, 448 = no exposure at all
 * 0x10		Gain 0-31
 * 0x12		Another gain 0-31, unlike 0x10 this one seems to start with an
 *		amplification value of 1 rather then 0 at its lowest setting
 * 0x21		Bitfield: 0-1 unused, 2-3 vflip/hflip, 4-5 unknown, 6-7 unused
 * 0x80		Another framerate control, best left at 1, moving it from 1 to
 *		2 causes the framerate to become 3/4th of what it was, and
 *		also seems to cause pixel averaging, resulting in an effective
 *		resolution of 320x240 and thus a much blockier image
 *
 * The registers are accessed in the following functions:
 *
 * Page | Register   | Function
 * -----+------------+---------------------------------------------------
 *  0   | 0x01       | setredbalance()
 *  0   | 0x03       | setbluebalance()
 *  0   | 0x0f..0x20 | setcolors()
 *  0   | 0xa2..0xab | setbrightcont()
 *  0   | 0xb6       | setsharpness()
 *  0   | 0xc6       | setwhitebalance()
 *  0   | 0xdc       | setbrightcont(), setcolors()
 *  3   | 0x02       | setexposure()
 *  3   | 0x10, 0x12 | setgain()
 *  3   | 0x11       | setcolors(), setgain(), setexposure(), sethvflip()
 *  3   | 0x21       | sethvflip()
 */

#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

#include <linux/input.h>
#include "gspca.h"
/* Include pac common sof detection functions */
#include "pac_common.h"

#define PAC7302_RGB_BALANCE_MIN		  0
#define PAC7302_RGB_BALANCE_MAX		200
#define PAC7302_RGB_BALANCE_DEFAULT	100
#define PAC7302_GAIN_DEFAULT		 15
#define PAC7302_GAIN_KNEE		 42
#define PAC7302_EXPOSURE_DEFAULT	 66 /* 33 ms / 30 fps */
#define PAC7302_EXPOSURE_KNEE		133 /* 66 ms / 15 fps */

MODULE_AUTHOR("Jean-Francois Moine <http://moinejf.free.fr>, Thomas Kaiser thomas@kaiser-linux.li");
MODULE_DESCRIPTION("Pixart PAC7302");
MODULE_LICENSE("GPL");

struct sd {
	struct gspca_dev gspca_dev;		/* !! must be the first item */

	struct { /* brightness / contrast cluster */
		struct v4l2_ctrl *brightness;
		struct v4l2_ctrl *contrast;
	};
	struct v4l2_ctrl *saturation;
	struct v4l2_ctrl *white_balance;
	struct v4l2_ctrl *red_balance;
	struct v4l2_ctrl *blue_balance;
	struct { /* flip cluster */
		struct v4l2_ctrl *hflip;
		struct v4l2_ctrl *vflip;
	};
	struct v4l2_ctrl *sharpness;
	u8 flags;
#define FL_HFLIP 0x01		/* mirrored by default */
#define FL_VFLIP 0x02		/* vertical flipped by default */

	u8 sof_read;
	s8 autogain_ignore_frames;

	atomic_t avg_lum;
};

static const struct v4l2_pix_format vga_mode[] = {
	{640, 480, V4L2_PIX_FMT_PJPG, V4L2_FIELD_NONE,
		.bytesperline = 640,
		.sizeimage = 640 * 480 * 3 / 8 + 590,
		.colorspace = V4L2_COLORSPACE_JPEG,
	},
};

#define LOAD_PAGE3		255
#define END_OF_SEQUENCE		0

static const u8 init_7302[] = {
/*	index,value */
	0xff, 0x01,		/* page 1 */
	0x78, 0x00,		/* deactivate */
	0xff, 0x01,
	0x78, 0x40,		/* led off */
};
static const u8 start_7302[] = {
/*	index, len, [value]* */
	0xff, 1,	0x00,		/* page 0 */
	0x00, 12,	0x01, 0x40, 0x40, 0x40, 0x01, 0xe0, 0x02, 0x80,
			0x00, 0x00, 0x00, 0x00,
	0x0d, 24,	0x03, 0x01, 0x00, 0xb5, 0x07, 0xcb, 0x00, 0x00,
			0x07, 0xc8, 0x00, 0xea, 0x07, 0xcf, 0x07, 0xf7,
			0x07, 0x7e, 0x01, 0x0b, 0x00, 0x00, 0x00, 0x11,
	0x26, 2,	0xaa, 0xaa,
	0x2e, 1,	0x31,
	0x38, 1,	0x01,
	0x3a, 3,	0x14, 0xff, 0x5a,
	0x43, 11,	0x00, 0x0a, 0x18, 0x11, 0x01, 0x2c, 0x88, 0x11,
			0x00, 0x54, 0x11,
	0x55, 1,	0x00,
	0x62, 4,	0x10, 0x1e, 0x1e, 0x18,
	0x6b, 1,	0x00,
	0x6e, 3,	0x08, 0x06, 0x00,
	0x72, 3,	0x00, 0xff, 0x00,
	0x7d, 23,	0x01, 0x01, 0x58, 0x46, 0x50, 0x3c, 0x50, 0x3c,
			0x54, 0x46, 0x54, 0x56, 0x52, 0x50, 0x52, 0x50,
			0x56, 0x64, 0xa4, 0x00, 0xda, 0x00, 0x00,
	0xa2, 10,	0x22, 0x2c, 0x3c, 0x54, 0x69, 0x7c, 0x9c, 0xb9,
			0xd2, 0xeb,
	0xaf, 1,	0x02,
	0xb5, 2,	0x08, 0x08,
	0xb8, 2,	0x08, 0x88,
	0xc4, 4,	0xae, 0x01, 0x04, 0x01,
	0xcc, 1,	0x00,
	0xd1, 11,	0x01, 0x30, 0x49, 0x5e, 0x6f, 0x7f, 0x8e, 0xa9,
			0xc1, 0xd7, 0xec,
	0xdc, 1,	0x01,
	0xff, 1,	0x01,		/* page 1 */
	0x12, 3,	0x02, 0x00, 0x01,
	0x3e, 2,	0x00, 0x00,
	0x76, 5,	0x01, 0x20, 0x40, 0x00, 0xf2,
	0x7c, 1,	0x00,
	0x7f, 10,	0x4b, 0x0f, 0x01, 0x2c, 0x02, 0x58, 0x03, 0x20,
			0x02, 0x00,
	0x96, 5,	0x01, 0x10, 0x04, 0x01, 0x04,
	0xc8, 14,	0x00, 0x00, 0x00, 0x00, 0x00, 0x07, 0x00, 0x00,
			0x07, 0x00, 0x01, 0x07, 0x04, 0x01,
	0xd8, 1,	0x01,
	0xdb, 2,	0x00, 0x01,
	0xde, 7,	0x00, 0x01, 0x04, 0x04, 0x00, 0x00, 0x00,
	0xe6, 4,	0x00, 0x00, 0x00, 0x01,
	0xeb, 1,	0x00,
	0xff, 1,	0x02,		/* page 2 */
	0x22, 1,	0x00,
	0xff, 1,	0x03,		/* page 3 */
	0, LOAD_PAGE3,			/* load the page 3 */
	0x11, 1,	0x01,
	0xff, 1,	0x02,		/* page 2 */
	0x13, 1,	0x00,
	0x22, 4,	0x1f, 0xa4, 0xf0, 0x96,
	0x27, 2,	0x14, 0x0c,
	0x2a, 5,	0xc8, 0x00, 0x18, 0x12, 0x22,
	0x64, 8,	0x00, 0x00, 0xf0, 0x01, 0x14, 0x44, 0x44, 0x44,
	0x6e, 1,	0x08,
	0xff, 1,	0x01,		/* page 1 */
	0x78, 1,	0x00,
	0, END_OF_SEQUENCE		/* end of sequence */
};

#define SKIP		0xaa
/* page 3 - the value SKIP says skip the index - see reg_w_page() */
static const u8 page3_7302[] = {
	0x90, 0x40, 0x03, 0x00, 0xc0, 0x01, 0x14, 0x16,
	0x14, 0x12, 0x00, 0x00, 0x00, 0x02, 0x33, 0x00,
	0x0f, 0x01, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
	0x00, 0x00, 0x00, 0x47, 0x01, 0xb3, 0x01, 0x00,
	0x00, 0x08, 0x00, 0x00, 0x0d, 0x00, 0x00, 0x21,
	0x00, 0x00, 0x00, 0x54, 0xf4, 0x02, 0x52, 0x54,
	0xa4, 0xb8, 0xe0, 0x2a, 0xf6, 0x00, 0x00, 0x00,
	0x00, 0x1e, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
	0x00, 0xfc, 0x00, 0xf2, 0x1f, 0x04, 0x00, 0x00,
	SKIP, 0x00, 0x00, 0xc0, 0xc0, 0x10, 0x00, 0x00,
	0x00, 0x40, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
	0x00, 0x40, 0xff, 0x03, 0x19, 0x00, 0x00, 0x00,
	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
	0x00, 0x00, 0x00, 0x00, 0x00, 0xc8, 0xc8, 0xc8,
	0xc8, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x50,
	0x08, 0x10, 0x24, 0x40, 0x00, 0x00, 0x00, 0x00,
	0x01, 0x00, 0x02, 0x47, 0x00, 0x00, 0x00, 0x00,
	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
	0x00, 0x02, 0xfa, 0x00, 0x64, 0x5a, 0x28, 0x00,
	0x00
};

static void reg_w_buf(struct gspca_dev *gspca_dev,
		u8 index,
		  const u8 *buffer, int len)
{
	int ret;

	if (gspca_dev->usb_err < 0)
		return;
	memcpy(gspca_dev->usb_buf, buffer, len);
	ret = usb_control_msg(gspca_dev->dev,
			usb_sndctrlpipe(gspca_dev->dev, 0),
			0,		/* request */
			USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
			0,		/* value */
			index, gspca_dev->usb_buf, len,
			500);
	if (ret < 0) {
		pr_err("reg_w_buf failed i: %02x error %d\n",
		       index, ret);
		gspca_dev->usb_err = ret;
	}
}


static void reg_w(struct gspca_dev *gspca_dev,
		u8 index,
		u8 value)
{
	int ret;

	if (gspca_dev->usb_err < 0)
		return;
	gspca_dev->usb_buf[0] = value;
	ret = usb_control_msg(gspca_dev->dev,
			usb_sndctrlpipe(gspca_dev->dev, 0),
			0,			/* request */
			USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
			0, index, gspca_dev->usb_buf, 1,
			500);
	if (ret < 0) {
		pr_err("reg_w() failed i: %02x v: %02x error %d\n",
		       index, value, ret);
		gspca_dev->usb_err = ret;
	}
}

static void reg_w_seq(struct gspca_dev *gspca_dev,
		const u8 *seq, int len)
{
	while (--len >= 0) {
		reg_w(gspca_dev, seq[0], seq[1]);
		seq += 2;
	}
}

/* load the beginning of a page */
static void reg_w_page(struct gspca_dev *gspca_dev,
			const u8 *page, int len)
{
	int index;
	int ret = 0;

	if (gspca_dev->usb_err < 0)
		return;
	for (index = 0; index < len; index++) {
		if (page[index] == SKIP)		/* skip this index */
			continue;
		gspca_dev->usb_buf[0] = page[index];
		ret = usb_control_msg(gspca_dev->dev,
				usb_sndctrlpipe(gspca_dev->dev, 0),
				0,			/* request */
			USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
				0, index, gspca_dev->usb_buf, 1,
				500);
		if (ret < 0) {
			pr_err("reg_w_page() failed i: %02x v: %02x error %d\n",
			       index, page[index], ret);
			gspca_dev->usb_err = ret;
			break;
		}
	}
}

/* output a variable sequence */
static void reg_w_var(struct gspca_dev *gspca_dev,
			const u8 *seq,
			const u8 *page3, unsigned int page3_len)
{
	int index, len;

	for (;;) {
		index = *seq++;
		len = *seq++;
		switch (len) {
		case END_OF_SEQUENCE:
			return;
		case LOAD_PAGE3:
			reg_w_page(gspca_dev, page3, page3_len);
			break;
		default:
			if (len > USB_BUF_SZ) {
				gspca_err(gspca_dev, "Incorrect variable sequence\n");
				return;
			}
			while (len > 0) {
				if (len < 8) {
					reg_w_buf(gspca_dev,
						index, seq, len);
					seq += len;
					break;
				}
				reg_w_buf(gspca_dev, index, seq, 8);
				seq += 8;
				index += 8;
				len -= 8;
			}
		}
	}
	/* not reached */
}

/* this function is called at probe time for pac7302 */
static int sd_config(struct gspca_dev *gspca_dev,
			const struct usb_device_id *id)
{
	struct sd *sd = (struct sd *) gspca_dev;
	struct cam *cam;

	cam = &gspca_dev->cam;

	cam->cam_mode = vga_mode;	/* only 640x480 */
	cam->nmodes = ARRAY_SIZE(vga_mode);

	sd->flags = id->driver_info;
	return 0;
}

static void setbrightcont(struct gspca_dev *gspca_dev)
{
	struct sd *sd = (struct sd *) gspca_dev;
	int i, v;
	static const u8 max[10] =
		{0x29, 0x33, 0x42, 0x5a, 0x6e, 0x80, 0x9f, 0xbb,
		 0xd4, 0xec};
	static const u8 delta[10] =
		{0x35, 0x33, 0x33, 0x2f, 0x2a, 0x25, 0x1e, 0x17,
		 0x11, 0x0b};

	reg_w(gspca_dev, 0xff, 0x00);		/* page 0 */
	for (i = 0; i < 10; i++) {
		v = max[i];
		v += (sd->brightness->val - (s32)sd->brightness->maximum)
			* 150 / (s32)sd->brightness->maximum; /* 200 ? */
		v -= delta[i] * sd->contrast->val / (s32)sd->contrast->maximum;
		if (v < 0)
			v = 0;
		else if (v > 0xff)
			v = 0xff;
		reg_w(gspca_dev, 0xa2 + i, v);
	}
	reg_w(gspca_dev, 0xdc, 0x01);
}

static void setcolors(struct gspca_dev *gspca_dev)
{
	struct sd *sd = (struct sd *) gspca_dev;
	int i, v;
	static const int a[9] =
		{217, -212, 0, -101, 170, -67, -38, -315, 355};
	static const int b[9] =
		{19, 106, 0, 19, 106, 1, 19, 106, 1};

	reg_w(gspca_dev, 0xff, 0x03);			/* page 3 */
	reg_w(gspca_dev, 0x11, 0x01);
	reg_w(gspca_dev, 0xff, 0x00);			/* page 0 */
	for (i = 0; i < 9; i++) {
		v = a[i] * sd->saturation->val / (s32)sd->saturation->maximum;
		v += b[i];
		reg_w(gspca_dev, 0x0f + 2 * i, (v >> 8) & 0x07);
		reg_w(gspca_dev, 0x0f + 2 * i + 1, v);
	}
	reg_w(gspca_dev, 0xdc, 0x01);
}

static void setwhitebalance(struct gspca_dev *gspca_dev)
{
	struct sd *sd = (struct sd *) gspca_dev;

	reg_w(gspca_dev, 0xff, 0x00);		/* page 0 */
	reg_w(gspca_dev, 0xc6, sd->white_balance->val);

	reg_w(gspca_dev, 0xdc, 0x01);
}

static u8 rgbbalance_ctrl_to_reg_value(s32 rgb_ctrl_val)
{
	const unsigned int k = 1000;	/* precision factor */
	unsigned int norm;

	/* Normed value [0...k] */
	norm = k * (rgb_ctrl_val - PAC7302_RGB_BALANCE_MIN)
		    / (PAC7302_RGB_BALANCE_MAX - PAC7302_RGB_BALANCE_MIN);
	/* Qudratic apporach improves control at small (register) values: */
	return 64 * norm * norm / (k*k)  +  32 * norm / k  +  32;
	/* Y = 64*X*X + 32*X + 32
	 * => register values 0x20-0x80; Windows driver uses these limits */

	/* NOTE: for full value range (0x00-0xff) use
	 *         Y = 254*X*X + X
	 *         => 254 * norm * norm / (k*k)  +  1 * norm / k	*/
}

static void setredbalance(struct gspca_dev *gspca_dev)
{
	struct sd *sd = (struct sd *) gspca_dev;

	reg_w(gspca_dev, 0xff, 0x00);			/* page 0 */
	reg_w(gspca_dev, 0x01,
	      rgbbalance_ctrl_to_reg_value(sd->red_balance->val));

	reg_w(gspca_dev, 0xdc, 0x01);
}

static void setbluebalance(struct gspca_dev *gspca_dev)
{
	struct sd *sd = (struct sd *) gspca_dev;

	reg_w(gspca_dev, 0xff, 0x00);			/* page 0 */
	reg_w(gspca_dev, 0x03,
	      rgbbalance_ctrl_to_reg_value(sd->blue_balance->val));

	reg_w(gspca_dev, 0xdc, 0x01);
}

static void setgain(struct gspca_dev *gspca_dev)
{
	u8 reg10, reg12;

	if (gspca_dev->gain->val < 32) {
		reg10 = gspca_dev->gain->val;
		reg12 = 0;
	} else {
		reg10 = 31;
		reg12 = gspca_dev->gain->val - 31;
	}

	reg_w(gspca_dev, 0xff, 0x03);			/* page 3 */
	reg_w(gspca_dev, 0x10, reg10);
	reg_w(gspca_dev, 0x12, reg12);

	/* load registers to sensor (Bit 0, auto clear) */
	reg_w(gspca_dev, 0x11, 0x01);
}

static void setexposure(struct gspca_dev *gspca_dev)
{
	u8 clockdiv;
	u16 exposure;

	/*
	 * Register 2 of frame 3 contains the clock divider configuring the
	 * no fps according to the formula: 90 / reg. sd->exposure is the
	 * desired exposure time in 0.5 ms.
	 */
	clockdiv = (90 * gspca_dev->exposure->val + 1999) / 2000;

	/*
	 * Note clockdiv = 3 also works, but when running at 30 fps, depending
	 * on the scene being recorded, the camera switches to another
	 * quantization table for certain JPEG blocks, and we don't know how
	 * to decompress these blocks. So we cap the framerate at 15 fps.
	 */
	if (clockdiv < 6)
		clockdiv = 6;
	else if (clockdiv > 63)
		clockdiv = 63;

	/*
	 * Register 2 MUST be a multiple of 3, except when between 6 and 12?
	 * Always round up, otherwise we cannot get the desired frametime
	 * using the partial frame time exposure control.
	 */
	if (clockdiv < 6 || clockdiv > 12)
		clockdiv = ((clockdiv + 2) / 3) * 3;

	/*
	 * frame exposure time in ms = 1000 * clockdiv / 90    ->
	 * exposure = (sd->exposure / 2) * 448 / (1000 * clockdiv / 90)
	 */
	exposure = (gspca_dev->exposure->val * 45 * 448) / (1000 * clockdiv);
	/* 0 = use full frametime, 448 = no exposure, reverse it */
	exposure = 448 - exposure;

	reg_w(gspca_dev, 0xff, 0x03);			/* page 3 */
	reg_w(gspca_dev, 0x02, clockdiv);
	reg_w(gspca_dev, 0x0e, exposure & 0xff);
	reg_w(gspca_dev, 0x0f, exposure >> 8);

	/* load registers to sensor (Bit 0, auto clear) */
	reg_w(gspca_dev, 0x11, 0x01);
}

static void sethvflip(struct gspca_dev *gspca_dev)
{
	struct sd *sd = (struct sd *) gspca_dev;
	u8 data, hflip, vflip;

	hflip = sd->hflip->val;
	if (sd->flags & FL_HFLIP)
		hflip = !hflip;
	vflip = sd->vflip->val;
	if (sd->flags & FL_VFLIP)
		vflip = !vflip;

	reg_w(gspca_dev, 0xff, 0x03);			/* page 3 */
	data = (hflip ? 0x08 : 0x00) | (vflip ? 0x04 : 0x00);
	reg_w(gspca_dev, 0x21, data);

	/* load registers to sensor (Bit 0, auto clear) */
	reg_w(gspca_dev, 0x11, 0x01);
}

static void setsharpness(struct gspca_dev *gspca_dev)
{
	struct sd *sd = (struct sd *) gspca_dev;

	reg_w(gspca_dev, 0xff, 0x00);		/* page 0 */
	reg_w(gspca_dev, 0xb6, sd->sharpness->val);

	reg_w(gspca_dev, 0xdc, 0x01);
}

/* this function is called at probe and resume time for pac7302 */
static int sd_init(struct gspca_dev *gspca_dev)
{
	reg_w_seq(gspca_dev, init_7302, sizeof(init_7302)/2);
	return gspca_dev->usb_err;
}

static int sd_s_ctrl(struct v4l2_ctrl *ctrl)
{
	struct gspca_dev *gspca_dev =
		container_of(ctrl->handler, struct gspca_dev, ctrl_handler);
	struct sd *sd = (struct sd *)gspca_dev;

	gspca_dev->usb_err = 0;

	if (ctrl->id == V4L2_CID_AUTOGAIN && ctrl->is_new && ctrl->val) {
		/* when switching to autogain set defaults to make sure
		   we are on a valid point of the autogain gain /
		   exposure knee graph, and give this change time to
		   take effect before doing autogain. */
		gspca_dev->exposure->val    = PAC7302_EXPOSURE_DEFAULT;
		gspca_dev->gain->val        = PAC7302_GAIN_DEFAULT;
		sd->autogain_ignore_frames  = PAC_AUTOGAIN_IGNORE_FRAMES;
	}

	if (!gspca_dev->streaming)
		return 0;

	switch (ctrl->id) {
	case V4L2_CID_BRIGHTNESS:
		setbrightcont(gspca_dev);
		break;
	case V4L2_CID_SATURATION:
		setcolors(gspca_dev);
		break;
	case V4L2_CID_WHITE_BALANCE_TEMPERATURE:
		setwhitebalance(gspca_dev);
		break;
	case V4L2_CID_RED_BALANCE:
		setredbalance(gspca_dev);
		break;
	case V4L2_CID_BLUE_BALANCE:
		setbluebalance(gspca_dev);
		break;
	case V4L2_CID_AUTOGAIN:
		if (gspca_dev->exposure->is_new || (ctrl->is_new && ctrl->val))
			setexposure(gspca_dev);
		if (gspca_dev->gain->is_new || (ctrl->is_new && ctrl->val))
			setgain(gspca_dev);
		break;
	case V4L2_CID_HFLIP:
		sethvflip(gspca_dev);
		break;
	case V4L2_CID_SHARPNESS:
		setsharpness(gspca_dev);
		break;
	default:
		return -EINVAL;
	}
	return gspca_dev->usb_err;
}

static const struct v4l2_ctrl_ops sd_ctrl_ops = {
	.s_ctrl = sd_s_ctrl,
};

/* this function is called at probe time */
static int sd_init_controls(struct gspca_dev *gspca_dev)
{
	struct sd *sd = (struct sd *) gspca_dev;
	struct v4l2_ctrl_handler *hdl = &gspca_dev->ctrl_handler;

	gspca_dev->vdev.ctrl_handler = hdl;
	v4l2_ctrl_handler_init(hdl, 12);

	sd->brightness = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops,
					V4L2_CID_BRIGHTNESS, 0, 32, 1, 16);
	sd->contrast = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops,
					V4L2_CID_CONTRAST, 0, 255, 1, 127);

	sd->saturation = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops,
					V4L2_CID_SATURATION, 0, 255, 1, 127);
	sd->white_balance = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops,
					V4L2_CID_WHITE_BALANCE_TEMPERATURE,
					0, 255, 1, 55);
	sd->red_balance = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops,
					V4L2_CID_RED_BALANCE,
					PAC7302_RGB_BALANCE_MIN,
					PAC7302_RGB_BALANCE_MAX,
					1, PAC7302_RGB_BALANCE_DEFAULT);
	sd->blue_balance = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops,
					V4L2_CID_BLUE_BALANCE,
					PAC7302_RGB_BALANCE_MIN,
					PAC7302_RGB_BALANCE_MAX,
					1, PAC7302_RGB_BALANCE_DEFAULT);

	gspca_dev->autogain = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops,
					V4L2_CID_AUTOGAIN, 0, 1, 1, 1);
	gspca_dev->exposure = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops,
					V4L2_CID_EXPOSURE, 0, 1023, 1,
					PAC7302_EXPOSURE_DEFAULT);
	gspca_dev->gain = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops,
					V4L2_CID_GAIN, 0, 62, 1,
					PAC7302_GAIN_DEFAULT);

	sd->hflip = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops,
		V4L2_CID_HFLIP, 0, 1, 1, 0);
	sd->vflip = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops,
		V4L2_CID_VFLIP, 0, 1, 1, 0);

	sd->sharpness = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops,
					V4L2_CID_SHARPNESS, 0, 15, 1, 8);

	if (hdl->error) {
		pr_err("Could not initialize controls\n");
		return hdl->error;
	}

	v4l2_ctrl_cluster(2, &sd->brightness);
	v4l2_ctrl_auto_cluster(3, &gspca_dev->autogain, 0, false);
	v4l2_ctrl_cluster(2, &sd->hflip);
	return 0;
}

/* -- start the camera -- */
static int sd_start(struct gspca_dev *gspca_dev)
{
	struct sd *sd = (struct sd *) gspca_dev;

	reg_w_var(gspca_dev, start_7302,
		page3_7302, sizeof(page3_7302));

	sd->sof_read = 0;
	sd->autogain_ignore_frames = 0;
	atomic_set(&sd->avg_lum, 270 + sd->brightness->val);

	/* start stream */
	reg_w(gspca_dev, 0xff, 0x01);
	reg_w(gspca_dev, 0x78, 0x01);

	return gspca_dev->usb_err;
}

static void sd_stopN(struct gspca_dev *gspca_dev)
{

	/* stop stream */
	reg_w(gspca_dev, 0xff, 0x01);
	reg_w(gspca_dev, 0x78, 0x00);
}

/* called on streamoff with alt 0 and on disconnect for pac7302 */
static void sd_stop0(struct gspca_dev *gspca_dev)
{
	if (!gspca_dev->present)
		return;
	reg_w(gspca_dev, 0xff, 0x01);
	reg_w(gspca_dev, 0x78, 0x40);
}

static void do_autogain(struct gspca_dev *gspca_dev)
{
	struct sd *sd = (struct sd *) gspca_dev;
	int avg_lum = atomic_read(&sd->avg_lum);
	int desired_lum;
	const int deadzone = 30;

	if (sd->autogain_ignore_frames < 0)
		return;

	if (sd->autogain_ignore_frames > 0) {
		sd->autogain_ignore_frames--;
	} else {
		desired_lum = 270 + sd->brightness->val;

		if (gspca_expo_autogain(gspca_dev, avg_lum, desired_lum,
					deadzone, PAC7302_GAIN_KNEE,
					PAC7302_EXPOSURE_KNEE))
			sd->autogain_ignore_frames =
						PAC_AUTOGAIN_IGNORE_FRAMES;
	}
}

/* JPEG header */
static const u8 jpeg_header[] = {
	0xff, 0xd8,	/* SOI: Start of Image */

	0xff, 0xc0,	/* SOF0: Start of Frame (Baseline DCT) */
	0x00, 0x11,	/* length = 17 bytes (including this length field) */
	0x08,		/* Precision: 8 */
	0x02, 0x80,	/* height = 640 (image rotated) */
	0x01, 0xe0,	/* width = 480 */
	0x03,		/* Number of image components: 3 */
	0x01, 0x21, 0x00, /* ID=1, Subsampling 1x1, Quantization table: 0 */
	0x02, 0x11, 0x01, /* ID=2, Subsampling 2x1, Quantization table: 1 */
	0x03, 0x11, 0x01, /* ID=3, Subsampling 2x1, Quantization table: 1 */

	0xff, 0xda,	/* SOS: Start Of Scan */
	0x00, 0x0c,	/* length = 12 bytes (including this length field) */
	0x03,		/* number of components: 3 */
	0x01, 0x00,	/* selector 1, table 0x00 */
	0x02, 0x11,	/* selector 2, table 0x11 */
	0x03, 0x11,	/* selector 3, table 0x11 */
	0x00, 0x3f,	/* Spectral selection: 0 .. 63 */
	0x00		/* Successive approximation: 0 */
};

/* this function is run at interrupt level */
static void sd_pkt_scan(struct gspca_dev *gspca_dev,
			u8 *data,			/* isoc packet */
			int len)			/* iso packet length */
{
	struct sd *sd = (struct sd *) gspca_dev;
	u8 *image;
	u8 *sof;

	sof = pac_find_sof(gspca_dev, &sd->sof_read, data, len);
	if (sof) {
		int n, lum_offset, footer_length;

		/*
		 * 6 bytes after the FF D9 EOF marker a number of lumination
		 * bytes are send corresponding to different parts of the
		 * image, the 14th and 15th byte after the EOF seem to
		 * correspond to the center of the image.
		 */
		lum_offset = 61 + sizeof pac_sof_marker;
		footer_length = 74;

		/* Finish decoding current frame */
		n = (sof - data) - (footer_length + sizeof pac_sof_marker);
		if (n < 0) {
			gspca_dev->image_len += n;
			n = 0;
		} else {
			gspca_frame_add(gspca_dev, INTER_PACKET, data, n);
		}

		image = gspca_dev->image;
		if (image != NULL
		 && image[gspca_dev->image_len - 2] == 0xff
		 && image[gspca_dev->image_len - 1] == 0xd9)
			gspca_frame_add(gspca_dev, LAST_PACKET, NULL, 0);

		n = sof - data;
		len -= n;
		data = sof;

		/* Get average lumination */
		if (gspca_dev->last_packet_type == LAST_PACKET &&
				n >= lum_offset)
			atomic_set(&sd->avg_lum, data[-lum_offset] +
						data[-lum_offset + 1]);

		/* Start the new frame with the jpeg header */
		/* The PAC7302 has the image rotated 90 degrees */
		gspca_frame_add(gspca_dev, FIRST_PACKET,
				jpeg_header, sizeof jpeg_header);
	}
	gspca_frame_add(gspca_dev, INTER_PACKET, data, len);
}

#ifdef CONFIG_VIDEO_ADV_DEBUG
static int sd_dbg_s_register(struct gspca_dev *gspca_dev,
			const struct v4l2_dbg_register *reg)
{
	u8 index;
	u8 value;

	/*
	 * reg->reg: bit0..15: reserved for register index (wIndex is 16bit
	 *		       long on the USB bus)
	 */
	if (reg->match.addr == 0 &&
	    (reg->reg < 0x000000ff) &&
	    (reg->val <= 0x000000ff)
	) {
		/* Currently writing to page 0 is only supported. */
		/* reg_w() only supports 8bit index */
		index = reg->reg;
		value = reg->val;

		/*
		 * Note that there shall be no access to other page
		 * by any other function between the page switch and
		 * the actual register write.
		 */
		reg_w(gspca_dev, 0xff, 0x00);		/* page 0 */
		reg_w(gspca_dev, index, value);

		reg_w(gspca_dev, 0xdc, 0x01);
	}
	return gspca_dev->usb_err;
}
#endif

#if IS_ENABLED(CONFIG_INPUT)
static int sd_int_pkt_scan(struct gspca_dev *gspca_dev,
			u8 *data,		/* interrupt packet data */
			int len)		/* interrupt packet length */
{
	int ret = -EINVAL;
	u8 data0, data1;

	if (len == 2) {
		data0 = data[0];
		data1 = data[1];
		if ((data0 == 0x00 && data1 == 0x11) ||
		    (data0 == 0x22 && data1 == 0x33) ||
		    (data0 == 0x44 && data1 == 0x55) ||
		    (data0 == 0x66 && data1 == 0x77) ||
		    (data0 == 0x88 && data1 == 0x99) ||
		    (data0 == 0xaa && data1 == 0xbb) ||
		    (data0 == 0xcc && data1 == 0xdd) ||
		    (data0 == 0xee && data1 == 0xff)) {
			input_report_key(gspca_dev->input_dev, KEY_CAMERA, 1);
			input_sync(gspca_dev->input_dev);
			input_report_key(gspca_dev->input_dev, KEY_CAMERA, 0);
			input_sync(gspca_dev->input_dev);
			ret = 0;
		}
	}

	return ret;
}
#endif

/* sub-driver description for pac7302 */
static const struct sd_desc sd_desc = {
	.name = KBUILD_MODNAME,
	.config = sd_config,
	.init = sd_init,
	.init_controls = sd_init_controls,
	.start = sd_start,
	.stopN = sd_stopN,
	.stop0 = sd_stop0,
	.pkt_scan = sd_pkt_scan,
	.dq_callback = do_autogain,
#ifdef CONFIG_VIDEO_ADV_DEBUG
	.set_register = sd_dbg_s_register,
#endif
#if IS_ENABLED(CONFIG_INPUT)
	.int_pkt_scan = sd_int_pkt_scan,
#endif
};

/* -- module initialisation -- */
static const struct usb_device_id device_table[] = {
	{USB_DEVICE(0x06f8, 0x3009)},
	{USB_DEVICE(0x06f8, 0x301b)},
	{USB_DEVICE(0x093a, 0x2620)},
	{USB_DEVICE(0x093a, 0x2621)},
	{USB_DEVICE(0x093a, 0x2622), .driver_info = FL_VFLIP},
	{USB_DEVICE(0x093a, 0x2623), .driver_info = FL_VFLIP},
	{USB_DEVICE(0x093a, 0x2624), .driver_info = FL_VFLIP},
	{USB_DEVICE(0x093a, 0x2625)},
	{USB_DEVICE(0x093a, 0x2626)},
	{USB_DEVICE(0x093a, 0x2627), .driver_info = FL_VFLIP},
	{USB_DEVICE(0x093a, 0x2628)},
	{USB_DEVICE(0x093a, 0x2629), .driver_info = FL_VFLIP},
	{USB_DEVICE(0x093a, 0x262a)},
	{USB_DEVICE(0x093a, 0x262c)},
	{USB_DEVICE(0x145f, 0x013c)},
	{USB_DEVICE(0x1ae7, 0x2001)}, /* SpeedLink Snappy Mic SL-6825-SBK */
	{}
};
MODULE_DEVICE_TABLE(usb, device_table);

/* -- device connect -- */
static int sd_probe(struct usb_interface *intf,
			const struct usb_device_id *id)
{
	return gspca_dev_probe(intf, id, &sd_desc, sizeof(struct sd),
				THIS_MODULE);
}

static struct usb_driver sd_driver = {
	.name = KBUILD_MODNAME,
	.id_table = device_table,
	.probe = sd_probe,
	.disconnect = gspca_disconnect,
#ifdef CONFIG_PM
	.suspend = gspca_suspend,
	.resume = gspca_resume,
	.reset_resume = gspca_resume,
#endif
};

module_usb_driver(sd_driver);