1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * ov2640 Camera Driver 4 * 5 * Copyright (C) 2010 Alberto Panizzo <maramaopercheseimorto@gmail.com> 6 * 7 * Based on ov772x, ov9640 drivers and previous non merged implementations. 8 * 9 * Copyright 2005-2009 Freescale Semiconductor, Inc. All Rights Reserved. 10 * Copyright (C) 2006, OmniVision 11 */ 12 13#include <linux/init.h> 14#include <linux/module.h> 15#include <linux/i2c.h> 16#include <linux/clk.h> 17#include <linux/slab.h> 18#include <linux/delay.h> 19#include <linux/gpio.h> 20#include <linux/gpio/consumer.h> 21#include <linux/of_gpio.h> 22#include <linux/v4l2-mediabus.h> 23#include <linux/videodev2.h> 24 25#include <media/v4l2-device.h> 26#include <media/v4l2-event.h> 27#include <media/v4l2-subdev.h> 28#include <media/v4l2-ctrls.h> 29#include <media/v4l2-image-sizes.h> 30 31#define VAL_SET(x, mask, rshift, lshift) \ 32 ((((x) >> rshift) & mask) << lshift) 33/* 34 * DSP registers 35 * register offset for BANK_SEL == BANK_SEL_DSP 36 */ 37#define R_BYPASS 0x05 /* Bypass DSP */ 38#define R_BYPASS_DSP_BYPAS 0x01 /* Bypass DSP, sensor out directly */ 39#define R_BYPASS_USE_DSP 0x00 /* Use the internal DSP */ 40#define QS 0x44 /* Quantization Scale Factor */ 41#define CTRLI 0x50 42#define CTRLI_LP_DP 0x80 43#define CTRLI_ROUND 0x40 44#define CTRLI_V_DIV_SET(x) VAL_SET(x, 0x3, 0, 3) 45#define CTRLI_H_DIV_SET(x) VAL_SET(x, 0x3, 0, 0) 46#define HSIZE 0x51 /* H_SIZE[7:0] (real/4) */ 47#define HSIZE_SET(x) VAL_SET(x, 0xFF, 2, 0) 48#define VSIZE 0x52 /* V_SIZE[7:0] (real/4) */ 49#define VSIZE_SET(x) VAL_SET(x, 0xFF, 2, 0) 50#define XOFFL 0x53 /* OFFSET_X[7:0] */ 51#define XOFFL_SET(x) VAL_SET(x, 0xFF, 0, 0) 52#define YOFFL 0x54 /* OFFSET_Y[7:0] */ 53#define YOFFL_SET(x) VAL_SET(x, 0xFF, 0, 0) 54#define VHYX 0x55 /* Offset and size completion */ 55#define VHYX_VSIZE_SET(x) VAL_SET(x, 0x1, (8+2), 7) 56#define VHYX_HSIZE_SET(x) VAL_SET(x, 0x1, (8+2), 3) 57#define VHYX_YOFF_SET(x) VAL_SET(x, 0x3, 8, 4) 58#define VHYX_XOFF_SET(x) VAL_SET(x, 0x3, 8, 0) 59#define DPRP 0x56 60#define TEST 0x57 /* Horizontal size completion */ 61#define TEST_HSIZE_SET(x) VAL_SET(x, 0x1, (9+2), 7) 62#define ZMOW 0x5A /* Zoom: Out Width OUTW[7:0] (real/4) */ 63#define ZMOW_OUTW_SET(x) VAL_SET(x, 0xFF, 2, 0) 64#define ZMOH 0x5B /* Zoom: Out Height OUTH[7:0] (real/4) */ 65#define ZMOH_OUTH_SET(x) VAL_SET(x, 0xFF, 2, 0) 66#define ZMHH 0x5C /* Zoom: Speed and H&W completion */ 67#define ZMHH_ZSPEED_SET(x) VAL_SET(x, 0x0F, 0, 4) 68#define ZMHH_OUTH_SET(x) VAL_SET(x, 0x1, (8+2), 2) 69#define ZMHH_OUTW_SET(x) VAL_SET(x, 0x3, (8+2), 0) 70#define BPADDR 0x7C /* SDE Indirect Register Access: Address */ 71#define BPDATA 0x7D /* SDE Indirect Register Access: Data */ 72#define CTRL2 0x86 /* DSP Module enable 2 */ 73#define CTRL2_DCW_EN 0x20 74#define CTRL2_SDE_EN 0x10 75#define CTRL2_UV_ADJ_EN 0x08 76#define CTRL2_UV_AVG_EN 0x04 77#define CTRL2_CMX_EN 0x01 78#define CTRL3 0x87 /* DSP Module enable 3 */ 79#define CTRL3_BPC_EN 0x80 80#define CTRL3_WPC_EN 0x40 81#define SIZEL 0x8C /* Image Size Completion */ 82#define SIZEL_HSIZE8_11_SET(x) VAL_SET(x, 0x1, 11, 6) 83#define SIZEL_HSIZE8_SET(x) VAL_SET(x, 0x7, 0, 3) 84#define SIZEL_VSIZE8_SET(x) VAL_SET(x, 0x7, 0, 0) 85#define HSIZE8 0xC0 /* Image Horizontal Size HSIZE[10:3] */ 86#define HSIZE8_SET(x) VAL_SET(x, 0xFF, 3, 0) 87#define VSIZE8 0xC1 /* Image Vertical Size VSIZE[10:3] */ 88#define VSIZE8_SET(x) VAL_SET(x, 0xFF, 3, 0) 89#define CTRL0 0xC2 /* DSP Module enable 0 */ 90#define CTRL0_AEC_EN 0x80 91#define CTRL0_AEC_SEL 0x40 92#define CTRL0_STAT_SEL 0x20 93#define CTRL0_VFIRST 0x10 94#define CTRL0_YUV422 0x08 95#define CTRL0_YUV_EN 0x04 96#define CTRL0_RGB_EN 0x02 97#define CTRL0_RAW_EN 0x01 98#define CTRL1 0xC3 /* DSP Module enable 1 */ 99#define CTRL1_CIP 0x80 100#define CTRL1_DMY 0x40 101#define CTRL1_RAW_GMA 0x20 102#define CTRL1_DG 0x10 103#define CTRL1_AWB 0x08 104#define CTRL1_AWB_GAIN 0x04 105#define CTRL1_LENC 0x02 106#define CTRL1_PRE 0x01 107/* REG 0xC7 (unknown name): affects Auto White Balance (AWB) 108 * AWB_OFF 0x40 109 * AWB_SIMPLE 0x10 110 * AWB_ON 0x00 (Advanced AWB ?) */ 111#define R_DVP_SP 0xD3 /* DVP output speed control */ 112#define R_DVP_SP_AUTO_MODE 0x80 113#define R_DVP_SP_DVP_MASK 0x3F /* DVP PCLK = sysclk (48)/[6:0] (YUV0); 114 * = sysclk (48)/(2*[6:0]) (RAW);*/ 115#define IMAGE_MODE 0xDA /* Image Output Format Select */ 116#define IMAGE_MODE_Y8_DVP_EN 0x40 117#define IMAGE_MODE_JPEG_EN 0x10 118#define IMAGE_MODE_YUV422 0x00 119#define IMAGE_MODE_RAW10 0x04 /* (DVP) */ 120#define IMAGE_MODE_RGB565 0x08 121#define IMAGE_MODE_HREF_VSYNC 0x02 /* HREF timing select in DVP JPEG output 122 * mode (0 for HREF is same as sensor) */ 123#define IMAGE_MODE_LBYTE_FIRST 0x01 /* Byte swap enable for DVP 124 * 1: Low byte first UYVY (C2[4] =0) 125 * VYUY (C2[4] =1) 126 * 0: High byte first YUYV (C2[4]=0) 127 * YVYU (C2[4] = 1) */ 128#define RESET 0xE0 /* Reset */ 129#define RESET_MICROC 0x40 130#define RESET_SCCB 0x20 131#define RESET_JPEG 0x10 132#define RESET_DVP 0x04 133#define RESET_IPU 0x02 134#define RESET_CIF 0x01 135#define REGED 0xED /* Register ED */ 136#define REGED_CLK_OUT_DIS 0x10 137#define MS_SP 0xF0 /* SCCB Master Speed */ 138#define SS_ID 0xF7 /* SCCB Slave ID */ 139#define SS_CTRL 0xF8 /* SCCB Slave Control */ 140#define SS_CTRL_ADD_AUTO_INC 0x20 141#define SS_CTRL_EN 0x08 142#define SS_CTRL_DELAY_CLK 0x04 143#define SS_CTRL_ACC_EN 0x02 144#define SS_CTRL_SEN_PASS_THR 0x01 145#define MC_BIST 0xF9 /* Microcontroller misc register */ 146#define MC_BIST_RESET 0x80 /* Microcontroller Reset */ 147#define MC_BIST_BOOT_ROM_SEL 0x40 148#define MC_BIST_12KB_SEL 0x20 149#define MC_BIST_12KB_MASK 0x30 150#define MC_BIST_512KB_SEL 0x08 151#define MC_BIST_512KB_MASK 0x0C 152#define MC_BIST_BUSY_BIT_R 0x02 153#define MC_BIST_MC_RES_ONE_SH_W 0x02 154#define MC_BIST_LAUNCH 0x01 155#define BANK_SEL 0xFF /* Register Bank Select */ 156#define BANK_SEL_DSP 0x00 157#define BANK_SEL_SENS 0x01 158 159/* 160 * Sensor registers 161 * register offset for BANK_SEL == BANK_SEL_SENS 162 */ 163#define GAIN 0x00 /* AGC - Gain control gain setting */ 164#define COM1 0x03 /* Common control 1 */ 165#define COM1_1_DUMMY_FR 0x40 166#define COM1_3_DUMMY_FR 0x80 167#define COM1_7_DUMMY_FR 0xC0 168#define COM1_VWIN_LSB_UXGA 0x0F 169#define COM1_VWIN_LSB_SVGA 0x0A 170#define COM1_VWIN_LSB_CIF 0x06 171#define REG04 0x04 /* Register 04 */ 172#define REG04_DEF 0x20 /* Always set */ 173#define REG04_HFLIP_IMG 0x80 /* Horizontal mirror image ON/OFF */ 174#define REG04_VFLIP_IMG 0x40 /* Vertical flip image ON/OFF */ 175#define REG04_VREF_EN 0x10 176#define REG04_HREF_EN 0x08 177#define REG04_AEC_SET(x) VAL_SET(x, 0x3, 0, 0) 178#define REG08 0x08 /* Frame Exposure One-pin Control Pre-charge Row Num */ 179#define COM2 0x09 /* Common control 2 */ 180#define COM2_SOFT_SLEEP_MODE 0x10 /* Soft sleep mode */ 181 /* Output drive capability */ 182#define COM2_OCAP_Nx_SET(N) (((N) - 1) & 0x03) /* N = [1x .. 4x] */ 183#define PID 0x0A /* Product ID Number MSB */ 184#define VER 0x0B /* Product ID Number LSB */ 185#define COM3 0x0C /* Common control 3 */ 186#define COM3_BAND_50H 0x04 /* 0 For Banding at 60H */ 187#define COM3_BAND_AUTO 0x02 /* Auto Banding */ 188#define COM3_SING_FR_SNAPSH 0x01 /* 0 For enable live video output after the 189 * snapshot sequence*/ 190#define AEC 0x10 /* AEC[9:2] Exposure Value */ 191#define CLKRC 0x11 /* Internal clock */ 192#define CLKRC_EN 0x80 193#define CLKRC_DIV_SET(x) (((x) - 1) & 0x1F) /* CLK = XVCLK/(x) */ 194#define COM7 0x12 /* Common control 7 */ 195#define COM7_SRST 0x80 /* Initiates system reset. All registers are 196 * set to factory default values after which 197 * the chip resumes normal operation */ 198#define COM7_RES_UXGA 0x00 /* Resolution selectors for UXGA */ 199#define COM7_RES_SVGA 0x40 /* SVGA */ 200#define COM7_RES_CIF 0x20 /* CIF */ 201#define COM7_ZOOM_EN 0x04 /* Enable Zoom mode */ 202#define COM7_COLOR_BAR_TEST 0x02 /* Enable Color Bar Test Pattern */ 203#define COM8 0x13 /* Common control 8 */ 204#define COM8_DEF 0xC0 205#define COM8_BNDF_EN 0x20 /* Banding filter ON/OFF */ 206#define COM8_AGC_EN 0x04 /* AGC Auto/Manual control selection */ 207#define COM8_AEC_EN 0x01 /* Auto/Manual Exposure control */ 208#define COM9 0x14 /* Common control 9 209 * Automatic gain ceiling - maximum AGC value [7:5]*/ 210#define COM9_AGC_GAIN_2x 0x00 /* 000 : 2x */ 211#define COM9_AGC_GAIN_4x 0x20 /* 001 : 4x */ 212#define COM9_AGC_GAIN_8x 0x40 /* 010 : 8x */ 213#define COM9_AGC_GAIN_16x 0x60 /* 011 : 16x */ 214#define COM9_AGC_GAIN_32x 0x80 /* 100 : 32x */ 215#define COM9_AGC_GAIN_64x 0xA0 /* 101 : 64x */ 216#define COM9_AGC_GAIN_128x 0xC0 /* 110 : 128x */ 217#define COM10 0x15 /* Common control 10 */ 218#define COM10_PCLK_HREF 0x20 /* PCLK output qualified by HREF */ 219#define COM10_PCLK_RISE 0x10 /* Data is updated at the rising edge of 220 * PCLK (user can latch data at the next 221 * falling edge of PCLK). 222 * 0 otherwise. */ 223#define COM10_HREF_INV 0x08 /* Invert HREF polarity: 224 * HREF negative for valid data*/ 225#define COM10_VSINC_INV 0x02 /* Invert VSYNC polarity */ 226#define HSTART 0x17 /* Horizontal Window start MSB 8 bit */ 227#define HEND 0x18 /* Horizontal Window end MSB 8 bit */ 228#define VSTART 0x19 /* Vertical Window start MSB 8 bit */ 229#define VEND 0x1A /* Vertical Window end MSB 8 bit */ 230#define MIDH 0x1C /* Manufacturer ID byte - high */ 231#define MIDL 0x1D /* Manufacturer ID byte - low */ 232#define AEW 0x24 /* AGC/AEC - Stable operating region (upper limit) */ 233#define AEB 0x25 /* AGC/AEC - Stable operating region (lower limit) */ 234#define VV 0x26 /* AGC/AEC Fast mode operating region */ 235#define VV_HIGH_TH_SET(x) VAL_SET(x, 0xF, 0, 4) 236#define VV_LOW_TH_SET(x) VAL_SET(x, 0xF, 0, 0) 237#define REG2A 0x2A /* Dummy pixel insert MSB */ 238#define FRARL 0x2B /* Dummy pixel insert LSB */ 239#define ADDVFL 0x2D /* LSB of insert dummy lines in Vertical direction */ 240#define ADDVFH 0x2E /* MSB of insert dummy lines in Vertical direction */ 241#define YAVG 0x2F /* Y/G Channel Average value */ 242#define REG32 0x32 /* Common Control 32 */ 243#define REG32_PCLK_DIV_2 0x80 /* PCLK freq divided by 2 */ 244#define REG32_PCLK_DIV_4 0xC0 /* PCLK freq divided by 4 */ 245#define ARCOM2 0x34 /* Zoom: Horizontal start point */ 246#define REG45 0x45 /* Register 45 */ 247#define FLL 0x46 /* Frame Length Adjustment LSBs */ 248#define FLH 0x47 /* Frame Length Adjustment MSBs */ 249#define COM19 0x48 /* Zoom: Vertical start point */ 250#define ZOOMS 0x49 /* Zoom: Vertical start point */ 251#define COM22 0x4B /* Flash light control */ 252#define COM25 0x4E /* For Banding operations */ 253#define COM25_50HZ_BANDING_AEC_MSBS_MASK 0xC0 /* 50Hz Bd. AEC 2 MSBs */ 254#define COM25_60HZ_BANDING_AEC_MSBS_MASK 0x30 /* 60Hz Bd. AEC 2 MSBs */ 255#define COM25_50HZ_BANDING_AEC_MSBS_SET(x) VAL_SET(x, 0x3, 8, 6) 256#define COM25_60HZ_BANDING_AEC_MSBS_SET(x) VAL_SET(x, 0x3, 8, 4) 257#define BD50 0x4F /* 50Hz Banding AEC 8 LSBs */ 258#define BD50_50HZ_BANDING_AEC_LSBS_SET(x) VAL_SET(x, 0xFF, 0, 0) 259#define BD60 0x50 /* 60Hz Banding AEC 8 LSBs */ 260#define BD60_60HZ_BANDING_AEC_LSBS_SET(x) VAL_SET(x, 0xFF, 0, 0) 261#define REG5A 0x5A /* 50/60Hz Banding Maximum AEC Step */ 262#define BD50_MAX_AEC_STEP_MASK 0xF0 /* 50Hz Banding Max. AEC Step */ 263#define BD60_MAX_AEC_STEP_MASK 0x0F /* 60Hz Banding Max. AEC Step */ 264#define BD50_MAX_AEC_STEP_SET(x) VAL_SET((x - 1), 0x0F, 0, 4) 265#define BD60_MAX_AEC_STEP_SET(x) VAL_SET((x - 1), 0x0F, 0, 0) 266#define REG5D 0x5D /* AVGsel[7:0], 16-zone average weight option */ 267#define REG5E 0x5E /* AVGsel[15:8], 16-zone average weight option */ 268#define REG5F 0x5F /* AVGsel[23:16], 16-zone average weight option */ 269#define REG60 0x60 /* AVGsel[31:24], 16-zone average weight option */ 270#define HISTO_LOW 0x61 /* Histogram Algorithm Low Level */ 271#define HISTO_HIGH 0x62 /* Histogram Algorithm High Level */ 272 273/* 274 * ID 275 */ 276#define MANUFACTURER_ID 0x7FA2 277#define PID_OV2640 0x2642 278#define VERSION(pid, ver) ((pid << 8) | (ver & 0xFF)) 279 280/* 281 * Struct 282 */ 283struct regval_list { 284 u8 reg_num; 285 u8 value; 286}; 287 288struct ov2640_win_size { 289 char *name; 290 u32 width; 291 u32 height; 292 const struct regval_list *regs; 293}; 294 295 296struct ov2640_priv { 297 struct v4l2_subdev subdev; 298#if defined(CONFIG_MEDIA_CONTROLLER) 299 struct media_pad pad; 300#endif 301 struct v4l2_ctrl_handler hdl; 302 u32 cfmt_code; 303 struct clk *clk; 304 const struct ov2640_win_size *win; 305 306 struct gpio_desc *resetb_gpio; 307 struct gpio_desc *pwdn_gpio; 308 309 struct mutex lock; /* lock to protect streaming and power_count */ 310 bool streaming; 311 int power_count; 312}; 313 314/* 315 * Registers settings 316 */ 317 318#define ENDMARKER { 0xff, 0xff } 319 320static const struct regval_list ov2640_init_regs[] = { 321 { BANK_SEL, BANK_SEL_DSP }, 322 { 0x2c, 0xff }, 323 { 0x2e, 0xdf }, 324 { BANK_SEL, BANK_SEL_SENS }, 325 { 0x3c, 0x32 }, 326 { CLKRC, CLKRC_DIV_SET(1) }, 327 { COM2, COM2_OCAP_Nx_SET(3) }, 328 { REG04, REG04_DEF | REG04_HREF_EN }, 329 { COM8, COM8_DEF | COM8_BNDF_EN | COM8_AGC_EN | COM8_AEC_EN }, 330 { COM9, COM9_AGC_GAIN_8x | 0x08}, 331 { 0x2c, 0x0c }, 332 { 0x33, 0x78 }, 333 { 0x3a, 0x33 }, 334 { 0x3b, 0xfb }, 335 { 0x3e, 0x00 }, 336 { 0x43, 0x11 }, 337 { 0x16, 0x10 }, 338 { 0x39, 0x02 }, 339 { 0x35, 0x88 }, 340 { 0x22, 0x0a }, 341 { 0x37, 0x40 }, 342 { 0x23, 0x00 }, 343 { ARCOM2, 0xa0 }, 344 { 0x06, 0x02 }, 345 { 0x06, 0x88 }, 346 { 0x07, 0xc0 }, 347 { 0x0d, 0xb7 }, 348 { 0x0e, 0x01 }, 349 { 0x4c, 0x00 }, 350 { 0x4a, 0x81 }, 351 { 0x21, 0x99 }, 352 { AEW, 0x40 }, 353 { AEB, 0x38 }, 354 { VV, VV_HIGH_TH_SET(0x08) | VV_LOW_TH_SET(0x02) }, 355 { 0x5c, 0x00 }, 356 { 0x63, 0x00 }, 357 { FLL, 0x22 }, 358 { COM3, 0x38 | COM3_BAND_AUTO }, 359 { REG5D, 0x55 }, 360 { REG5E, 0x7d }, 361 { REG5F, 0x7d }, 362 { REG60, 0x55 }, 363 { HISTO_LOW, 0x70 }, 364 { HISTO_HIGH, 0x80 }, 365 { 0x7c, 0x05 }, 366 { 0x20, 0x80 }, 367 { 0x28, 0x30 }, 368 { 0x6c, 0x00 }, 369 { 0x6d, 0x80 }, 370 { 0x6e, 0x00 }, 371 { 0x70, 0x02 }, 372 { 0x71, 0x94 }, 373 { 0x73, 0xc1 }, 374 { 0x3d, 0x34 }, 375 { COM7, COM7_RES_UXGA | COM7_ZOOM_EN }, 376 { REG5A, BD50_MAX_AEC_STEP_SET(6) 377 | BD60_MAX_AEC_STEP_SET(8) }, /* 0x57 */ 378 { COM25, COM25_50HZ_BANDING_AEC_MSBS_SET(0x0bb) 379 | COM25_60HZ_BANDING_AEC_MSBS_SET(0x09c) }, /* 0x00 */ 380 { BD50, BD50_50HZ_BANDING_AEC_LSBS_SET(0x0bb) }, /* 0xbb */ 381 { BD60, BD60_60HZ_BANDING_AEC_LSBS_SET(0x09c) }, /* 0x9c */ 382 { BANK_SEL, BANK_SEL_DSP }, 383 { 0xe5, 0x7f }, 384 { MC_BIST, MC_BIST_RESET | MC_BIST_BOOT_ROM_SEL }, 385 { 0x41, 0x24 }, 386 { RESET, RESET_JPEG | RESET_DVP }, 387 { 0x76, 0xff }, 388 { 0x33, 0xa0 }, 389 { 0x42, 0x20 }, 390 { 0x43, 0x18 }, 391 { 0x4c, 0x00 }, 392 { CTRL3, CTRL3_BPC_EN | CTRL3_WPC_EN | 0x10 }, 393 { 0x88, 0x3f }, 394 { 0xd7, 0x03 }, 395 { 0xd9, 0x10 }, 396 { R_DVP_SP, R_DVP_SP_AUTO_MODE | 0x2 }, 397 { 0xc8, 0x08 }, 398 { 0xc9, 0x80 }, 399 { BPADDR, 0x00 }, 400 { BPDATA, 0x00 }, 401 { BPADDR, 0x03 }, 402 { BPDATA, 0x48 }, 403 { BPDATA, 0x48 }, 404 { BPADDR, 0x08 }, 405 { BPDATA, 0x20 }, 406 { BPDATA, 0x10 }, 407 { BPDATA, 0x0e }, 408 { 0x90, 0x00 }, 409 { 0x91, 0x0e }, 410 { 0x91, 0x1a }, 411 { 0x91, 0x31 }, 412 { 0x91, 0x5a }, 413 { 0x91, 0x69 }, 414 { 0x91, 0x75 }, 415 { 0x91, 0x7e }, 416 { 0x91, 0x88 }, 417 { 0x91, 0x8f }, 418 { 0x91, 0x96 }, 419 { 0x91, 0xa3 }, 420 { 0x91, 0xaf }, 421 { 0x91, 0xc4 }, 422 { 0x91, 0xd7 }, 423 { 0x91, 0xe8 }, 424 { 0x91, 0x20 }, 425 { 0x92, 0x00 }, 426 { 0x93, 0x06 }, 427 { 0x93, 0xe3 }, 428 { 0x93, 0x03 }, 429 { 0x93, 0x03 }, 430 { 0x93, 0x00 }, 431 { 0x93, 0x02 }, 432 { 0x93, 0x00 }, 433 { 0x93, 0x00 }, 434 { 0x93, 0x00 }, 435 { 0x93, 0x00 }, 436 { 0x93, 0x00 }, 437 { 0x93, 0x00 }, 438 { 0x93, 0x00 }, 439 { 0x96, 0x00 }, 440 { 0x97, 0x08 }, 441 { 0x97, 0x19 }, 442 { 0x97, 0x02 }, 443 { 0x97, 0x0c }, 444 { 0x97, 0x24 }, 445 { 0x97, 0x30 }, 446 { 0x97, 0x28 }, 447 { 0x97, 0x26 }, 448 { 0x97, 0x02 }, 449 { 0x97, 0x98 }, 450 { 0x97, 0x80 }, 451 { 0x97, 0x00 }, 452 { 0x97, 0x00 }, 453 { 0xa4, 0x00 }, 454 { 0xa8, 0x00 }, 455 { 0xc5, 0x11 }, 456 { 0xc6, 0x51 }, 457 { 0xbf, 0x80 }, 458 { 0xc7, 0x10 }, /* simple AWB */ 459 { 0xb6, 0x66 }, 460 { 0xb8, 0xA5 }, 461 { 0xb7, 0x64 }, 462 { 0xb9, 0x7C }, 463 { 0xb3, 0xaf }, 464 { 0xb4, 0x97 }, 465 { 0xb5, 0xFF }, 466 { 0xb0, 0xC5 }, 467 { 0xb1, 0x94 }, 468 { 0xb2, 0x0f }, 469 { 0xc4, 0x5c }, 470 { 0xa6, 0x00 }, 471 { 0xa7, 0x20 }, 472 { 0xa7, 0xd8 }, 473 { 0xa7, 0x1b }, 474 { 0xa7, 0x31 }, 475 { 0xa7, 0x00 }, 476 { 0xa7, 0x18 }, 477 { 0xa7, 0x20 }, 478 { 0xa7, 0xd8 }, 479 { 0xa7, 0x19 }, 480 { 0xa7, 0x31 }, 481 { 0xa7, 0x00 }, 482 { 0xa7, 0x18 }, 483 { 0xa7, 0x20 }, 484 { 0xa7, 0xd8 }, 485 { 0xa7, 0x19 }, 486 { 0xa7, 0x31 }, 487 { 0xa7, 0x00 }, 488 { 0xa7, 0x18 }, 489 { 0x7f, 0x00 }, 490 { 0xe5, 0x1f }, 491 { 0xe1, 0x77 }, 492 { 0xdd, 0x7f }, 493 { CTRL0, CTRL0_YUV422 | CTRL0_YUV_EN | CTRL0_RGB_EN }, 494 ENDMARKER, 495}; 496 497/* 498 * Register settings for window size 499 * The preamble, setup the internal DSP to input an UXGA (1600x1200) image. 500 * Then the different zooming configurations will setup the output image size. 501 */ 502static const struct regval_list ov2640_size_change_preamble_regs[] = { 503 { BANK_SEL, BANK_SEL_DSP }, 504 { RESET, RESET_DVP }, 505 { SIZEL, SIZEL_HSIZE8_11_SET(UXGA_WIDTH) | 506 SIZEL_HSIZE8_SET(UXGA_WIDTH) | 507 SIZEL_VSIZE8_SET(UXGA_HEIGHT) }, 508 { HSIZE8, HSIZE8_SET(UXGA_WIDTH) }, 509 { VSIZE8, VSIZE8_SET(UXGA_HEIGHT) }, 510 { CTRL2, CTRL2_DCW_EN | CTRL2_SDE_EN | 511 CTRL2_UV_AVG_EN | CTRL2_CMX_EN | CTRL2_UV_ADJ_EN }, 512 { HSIZE, HSIZE_SET(UXGA_WIDTH) }, 513 { VSIZE, VSIZE_SET(UXGA_HEIGHT) }, 514 { XOFFL, XOFFL_SET(0) }, 515 { YOFFL, YOFFL_SET(0) }, 516 { VHYX, VHYX_HSIZE_SET(UXGA_WIDTH) | VHYX_VSIZE_SET(UXGA_HEIGHT) | 517 VHYX_XOFF_SET(0) | VHYX_YOFF_SET(0)}, 518 { TEST, TEST_HSIZE_SET(UXGA_WIDTH) }, 519 ENDMARKER, 520}; 521 522#define PER_SIZE_REG_SEQ(x, y, v_div, h_div, pclk_div) \ 523 { CTRLI, CTRLI_LP_DP | CTRLI_V_DIV_SET(v_div) | \ 524 CTRLI_H_DIV_SET(h_div)}, \ 525 { ZMOW, ZMOW_OUTW_SET(x) }, \ 526 { ZMOH, ZMOH_OUTH_SET(y) }, \ 527 { ZMHH, ZMHH_OUTW_SET(x) | ZMHH_OUTH_SET(y) }, \ 528 { R_DVP_SP, pclk_div }, \ 529 { RESET, 0x00} 530 531static const struct regval_list ov2640_qcif_regs[] = { 532 PER_SIZE_REG_SEQ(QCIF_WIDTH, QCIF_HEIGHT, 3, 3, 4), 533 ENDMARKER, 534}; 535 536static const struct regval_list ov2640_qvga_regs[] = { 537 PER_SIZE_REG_SEQ(QVGA_WIDTH, QVGA_HEIGHT, 2, 2, 4), 538 ENDMARKER, 539}; 540 541static const struct regval_list ov2640_cif_regs[] = { 542 PER_SIZE_REG_SEQ(CIF_WIDTH, CIF_HEIGHT, 2, 2, 8), 543 ENDMARKER, 544}; 545 546static const struct regval_list ov2640_vga_regs[] = { 547 PER_SIZE_REG_SEQ(VGA_WIDTH, VGA_HEIGHT, 0, 0, 2), 548 ENDMARKER, 549}; 550 551static const struct regval_list ov2640_svga_regs[] = { 552 PER_SIZE_REG_SEQ(SVGA_WIDTH, SVGA_HEIGHT, 1, 1, 2), 553 ENDMARKER, 554}; 555 556static const struct regval_list ov2640_xga_regs[] = { 557 PER_SIZE_REG_SEQ(XGA_WIDTH, XGA_HEIGHT, 0, 0, 2), 558 { CTRLI, 0x00}, 559 ENDMARKER, 560}; 561 562static const struct regval_list ov2640_sxga_regs[] = { 563 PER_SIZE_REG_SEQ(SXGA_WIDTH, SXGA_HEIGHT, 0, 0, 2), 564 { CTRLI, 0x00}, 565 { R_DVP_SP, 2 | R_DVP_SP_AUTO_MODE }, 566 ENDMARKER, 567}; 568 569static const struct regval_list ov2640_uxga_regs[] = { 570 PER_SIZE_REG_SEQ(UXGA_WIDTH, UXGA_HEIGHT, 0, 0, 0), 571 { CTRLI, 0x00}, 572 { R_DVP_SP, 0 | R_DVP_SP_AUTO_MODE }, 573 ENDMARKER, 574}; 575 576#define OV2640_SIZE(n, w, h, r) \ 577 {.name = n, .width = w , .height = h, .regs = r } 578 579static const struct ov2640_win_size ov2640_supported_win_sizes[] = { 580 OV2640_SIZE("QCIF", QCIF_WIDTH, QCIF_HEIGHT, ov2640_qcif_regs), 581 OV2640_SIZE("QVGA", QVGA_WIDTH, QVGA_HEIGHT, ov2640_qvga_regs), 582 OV2640_SIZE("CIF", CIF_WIDTH, CIF_HEIGHT, ov2640_cif_regs), 583 OV2640_SIZE("VGA", VGA_WIDTH, VGA_HEIGHT, ov2640_vga_regs), 584 OV2640_SIZE("SVGA", SVGA_WIDTH, SVGA_HEIGHT, ov2640_svga_regs), 585 OV2640_SIZE("XGA", XGA_WIDTH, XGA_HEIGHT, ov2640_xga_regs), 586 OV2640_SIZE("SXGA", SXGA_WIDTH, SXGA_HEIGHT, ov2640_sxga_regs), 587 OV2640_SIZE("UXGA", UXGA_WIDTH, UXGA_HEIGHT, ov2640_uxga_regs), 588}; 589 590/* 591 * Register settings for pixel formats 592 */ 593static const struct regval_list ov2640_format_change_preamble_regs[] = { 594 { BANK_SEL, BANK_SEL_DSP }, 595 { R_BYPASS, R_BYPASS_USE_DSP }, 596 ENDMARKER, 597}; 598 599static const struct regval_list ov2640_yuyv_regs[] = { 600 { IMAGE_MODE, IMAGE_MODE_YUV422 }, 601 { 0xd7, 0x03 }, 602 { 0x33, 0xa0 }, 603 { 0xe5, 0x1f }, 604 { 0xe1, 0x67 }, 605 { RESET, 0x00 }, 606 { R_BYPASS, R_BYPASS_USE_DSP }, 607 ENDMARKER, 608}; 609 610static const struct regval_list ov2640_uyvy_regs[] = { 611 { IMAGE_MODE, IMAGE_MODE_LBYTE_FIRST | IMAGE_MODE_YUV422 }, 612 { 0xd7, 0x01 }, 613 { 0x33, 0xa0 }, 614 { 0xe1, 0x67 }, 615 { RESET, 0x00 }, 616 { R_BYPASS, R_BYPASS_USE_DSP }, 617 ENDMARKER, 618}; 619 620static const struct regval_list ov2640_rgb565_be_regs[] = { 621 { IMAGE_MODE, IMAGE_MODE_RGB565 }, 622 { 0xd7, 0x03 }, 623 { RESET, 0x00 }, 624 { R_BYPASS, R_BYPASS_USE_DSP }, 625 ENDMARKER, 626}; 627 628static const struct regval_list ov2640_rgb565_le_regs[] = { 629 { IMAGE_MODE, IMAGE_MODE_LBYTE_FIRST | IMAGE_MODE_RGB565 }, 630 { 0xd7, 0x03 }, 631 { RESET, 0x00 }, 632 { R_BYPASS, R_BYPASS_USE_DSP }, 633 ENDMARKER, 634}; 635 636static u32 ov2640_codes[] = { 637 MEDIA_BUS_FMT_YUYV8_2X8, 638 MEDIA_BUS_FMT_UYVY8_2X8, 639 MEDIA_BUS_FMT_YVYU8_2X8, 640 MEDIA_BUS_FMT_VYUY8_2X8, 641 MEDIA_BUS_FMT_RGB565_2X8_BE, 642 MEDIA_BUS_FMT_RGB565_2X8_LE, 643}; 644 645/* 646 * General functions 647 */ 648static struct ov2640_priv *to_ov2640(const struct i2c_client *client) 649{ 650 return container_of(i2c_get_clientdata(client), struct ov2640_priv, 651 subdev); 652} 653 654static int ov2640_write_array(struct i2c_client *client, 655 const struct regval_list *vals) 656{ 657 int ret; 658 659 while ((vals->reg_num != 0xff) || (vals->value != 0xff)) { 660 ret = i2c_smbus_write_byte_data(client, 661 vals->reg_num, vals->value); 662 dev_vdbg(&client->dev, "array: 0x%02x, 0x%02x", 663 vals->reg_num, vals->value); 664 665 if (ret < 0) 666 return ret; 667 vals++; 668 } 669 return 0; 670} 671 672static int ov2640_mask_set(struct i2c_client *client, 673 u8 reg, u8 mask, u8 set) 674{ 675 s32 val = i2c_smbus_read_byte_data(client, reg); 676 if (val < 0) 677 return val; 678 679 val &= ~mask; 680 val |= set & mask; 681 682 dev_vdbg(&client->dev, "masks: 0x%02x, 0x%02x", reg, val); 683 684 return i2c_smbus_write_byte_data(client, reg, val); 685} 686 687static int ov2640_reset(struct i2c_client *client) 688{ 689 int ret; 690 static const struct regval_list reset_seq[] = { 691 {BANK_SEL, BANK_SEL_SENS}, 692 {COM7, COM7_SRST}, 693 ENDMARKER, 694 }; 695 696 ret = ov2640_write_array(client, reset_seq); 697 if (ret) 698 goto err; 699 700 msleep(5); 701err: 702 dev_dbg(&client->dev, "%s: (ret %d)", __func__, ret); 703 return ret; 704} 705 706static const char * const ov2640_test_pattern_menu[] = { 707 "Disabled", 708 "Eight Vertical Colour Bars", 709}; 710 711/* 712 * functions 713 */ 714static int ov2640_s_ctrl(struct v4l2_ctrl *ctrl) 715{ 716 struct v4l2_subdev *sd = 717 &container_of(ctrl->handler, struct ov2640_priv, hdl)->subdev; 718 struct i2c_client *client = v4l2_get_subdevdata(sd); 719 struct ov2640_priv *priv = to_ov2640(client); 720 u8 val; 721 int ret; 722 723 /* v4l2_ctrl_lock() locks our own mutex */ 724 725 /* 726 * If the device is not powered up by the host driver, do not apply any 727 * controls to H/W at this time. Instead the controls will be restored 728 * when the streaming is started. 729 */ 730 if (!priv->power_count) 731 return 0; 732 733 ret = i2c_smbus_write_byte_data(client, BANK_SEL, BANK_SEL_SENS); 734 if (ret < 0) 735 return ret; 736 737 switch (ctrl->id) { 738 case V4L2_CID_VFLIP: 739 val = ctrl->val ? REG04_VFLIP_IMG | REG04_VREF_EN : 0x00; 740 return ov2640_mask_set(client, REG04, 741 REG04_VFLIP_IMG | REG04_VREF_EN, val); 742 /* NOTE: REG04_VREF_EN: 1 line shift / even/odd line swap */ 743 case V4L2_CID_HFLIP: 744 val = ctrl->val ? REG04_HFLIP_IMG : 0x00; 745 return ov2640_mask_set(client, REG04, REG04_HFLIP_IMG, val); 746 case V4L2_CID_TEST_PATTERN: 747 val = ctrl->val ? COM7_COLOR_BAR_TEST : 0x00; 748 return ov2640_mask_set(client, COM7, COM7_COLOR_BAR_TEST, val); 749 } 750 751 return -EINVAL; 752} 753 754#ifdef CONFIG_VIDEO_ADV_DEBUG 755static int ov2640_g_register(struct v4l2_subdev *sd, 756 struct v4l2_dbg_register *reg) 757{ 758 struct i2c_client *client = v4l2_get_subdevdata(sd); 759 int ret; 760 761 reg->size = 1; 762 if (reg->reg > 0xff) 763 return -EINVAL; 764 765 ret = i2c_smbus_read_byte_data(client, reg->reg); 766 if (ret < 0) 767 return ret; 768 769 reg->val = ret; 770 771 return 0; 772} 773 774static int ov2640_s_register(struct v4l2_subdev *sd, 775 const struct v4l2_dbg_register *reg) 776{ 777 struct i2c_client *client = v4l2_get_subdevdata(sd); 778 779 if (reg->reg > 0xff || 780 reg->val > 0xff) 781 return -EINVAL; 782 783 return i2c_smbus_write_byte_data(client, reg->reg, reg->val); 784} 785#endif 786 787static void ov2640_set_power(struct ov2640_priv *priv, int on) 788{ 789#ifdef CONFIG_GPIOLIB 790 if (priv->pwdn_gpio) 791 gpiod_direction_output(priv->pwdn_gpio, !on); 792 if (on && priv->resetb_gpio) { 793 /* Active the resetb pin to perform a reset pulse */ 794 gpiod_direction_output(priv->resetb_gpio, 1); 795 usleep_range(3000, 5000); 796 gpiod_set_value(priv->resetb_gpio, 0); 797 } 798#endif 799} 800 801static int ov2640_s_power(struct v4l2_subdev *sd, int on) 802{ 803 struct i2c_client *client = v4l2_get_subdevdata(sd); 804 struct ov2640_priv *priv = to_ov2640(client); 805 806 mutex_lock(&priv->lock); 807 808 /* 809 * If the power count is modified from 0 to != 0 or from != 0 to 0, 810 * update the power state. 811 */ 812 if (priv->power_count == !on) 813 ov2640_set_power(priv, on); 814 priv->power_count += on ? 1 : -1; 815 WARN_ON(priv->power_count < 0); 816 mutex_unlock(&priv->lock); 817 818 return 0; 819} 820 821/* Select the nearest higher resolution for capture */ 822static const struct ov2640_win_size *ov2640_select_win(u32 width, u32 height) 823{ 824 int i, default_size = ARRAY_SIZE(ov2640_supported_win_sizes) - 1; 825 826 for (i = 0; i < ARRAY_SIZE(ov2640_supported_win_sizes); i++) { 827 if (ov2640_supported_win_sizes[i].width >= width && 828 ov2640_supported_win_sizes[i].height >= height) 829 return &ov2640_supported_win_sizes[i]; 830 } 831 832 return &ov2640_supported_win_sizes[default_size]; 833} 834 835static int ov2640_set_params(struct i2c_client *client, 836 const struct ov2640_win_size *win, u32 code) 837{ 838 const struct regval_list *selected_cfmt_regs; 839 u8 val; 840 int ret; 841 842 switch (code) { 843 case MEDIA_BUS_FMT_RGB565_2X8_BE: 844 dev_dbg(&client->dev, "%s: Selected cfmt RGB565 BE", __func__); 845 selected_cfmt_regs = ov2640_rgb565_be_regs; 846 break; 847 case MEDIA_BUS_FMT_RGB565_2X8_LE: 848 dev_dbg(&client->dev, "%s: Selected cfmt RGB565 LE", __func__); 849 selected_cfmt_regs = ov2640_rgb565_le_regs; 850 break; 851 case MEDIA_BUS_FMT_YUYV8_2X8: 852 dev_dbg(&client->dev, "%s: Selected cfmt YUYV (YUV422)", __func__); 853 selected_cfmt_regs = ov2640_yuyv_regs; 854 break; 855 case MEDIA_BUS_FMT_UYVY8_2X8: 856 default: 857 dev_dbg(&client->dev, "%s: Selected cfmt UYVY", __func__); 858 selected_cfmt_regs = ov2640_uyvy_regs; 859 break; 860 case MEDIA_BUS_FMT_YVYU8_2X8: 861 dev_dbg(&client->dev, "%s: Selected cfmt YVYU", __func__); 862 selected_cfmt_regs = ov2640_yuyv_regs; 863 break; 864 case MEDIA_BUS_FMT_VYUY8_2X8: 865 dev_dbg(&client->dev, "%s: Selected cfmt VYUY", __func__); 866 selected_cfmt_regs = ov2640_uyvy_regs; 867 break; 868 } 869 870 /* reset hardware */ 871 ov2640_reset(client); 872 873 /* initialize the sensor with default data */ 874 dev_dbg(&client->dev, "%s: Init default", __func__); 875 ret = ov2640_write_array(client, ov2640_init_regs); 876 if (ret < 0) 877 goto err; 878 879 /* select preamble */ 880 dev_dbg(&client->dev, "%s: Set size to %s", __func__, win->name); 881 ret = ov2640_write_array(client, ov2640_size_change_preamble_regs); 882 if (ret < 0) 883 goto err; 884 885 /* set size win */ 886 ret = ov2640_write_array(client, win->regs); 887 if (ret < 0) 888 goto err; 889 890 /* cfmt preamble */ 891 dev_dbg(&client->dev, "%s: Set cfmt", __func__); 892 ret = ov2640_write_array(client, ov2640_format_change_preamble_regs); 893 if (ret < 0) 894 goto err; 895 896 /* set cfmt */ 897 ret = ov2640_write_array(client, selected_cfmt_regs); 898 if (ret < 0) 899 goto err; 900 val = (code == MEDIA_BUS_FMT_YVYU8_2X8) 901 || (code == MEDIA_BUS_FMT_VYUY8_2X8) ? CTRL0_VFIRST : 0x00; 902 ret = ov2640_mask_set(client, CTRL0, CTRL0_VFIRST, val); 903 if (ret < 0) 904 goto err; 905 906 return 0; 907 908err: 909 dev_err(&client->dev, "%s: Error %d", __func__, ret); 910 ov2640_reset(client); 911 912 return ret; 913} 914 915static int ov2640_get_fmt(struct v4l2_subdev *sd, 916 struct v4l2_subdev_pad_config *cfg, 917 struct v4l2_subdev_format *format) 918{ 919 struct v4l2_mbus_framefmt *mf = &format->format; 920 struct i2c_client *client = v4l2_get_subdevdata(sd); 921 struct ov2640_priv *priv = to_ov2640(client); 922 923 if (format->pad) 924 return -EINVAL; 925 926 if (format->which == V4L2_SUBDEV_FORMAT_TRY) { 927#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API 928 mf = v4l2_subdev_get_try_format(sd, cfg, 0); 929 format->format = *mf; 930 return 0; 931#else 932 return -EINVAL; 933#endif 934 } 935 936 mf->width = priv->win->width; 937 mf->height = priv->win->height; 938 mf->code = priv->cfmt_code; 939 mf->colorspace = V4L2_COLORSPACE_SRGB; 940 mf->field = V4L2_FIELD_NONE; 941 mf->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT; 942 mf->quantization = V4L2_QUANTIZATION_DEFAULT; 943 mf->xfer_func = V4L2_XFER_FUNC_DEFAULT; 944 945 return 0; 946} 947 948static int ov2640_set_fmt(struct v4l2_subdev *sd, 949 struct v4l2_subdev_pad_config *cfg, 950 struct v4l2_subdev_format *format) 951{ 952 struct v4l2_mbus_framefmt *mf = &format->format; 953 struct i2c_client *client = v4l2_get_subdevdata(sd); 954 struct ov2640_priv *priv = to_ov2640(client); 955 const struct ov2640_win_size *win; 956 int ret = 0; 957 958 if (format->pad) 959 return -EINVAL; 960 961 mutex_lock(&priv->lock); 962 963 /* select suitable win */ 964 win = ov2640_select_win(mf->width, mf->height); 965 mf->width = win->width; 966 mf->height = win->height; 967 968 mf->field = V4L2_FIELD_NONE; 969 mf->colorspace = V4L2_COLORSPACE_SRGB; 970 mf->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT; 971 mf->quantization = V4L2_QUANTIZATION_DEFAULT; 972 mf->xfer_func = V4L2_XFER_FUNC_DEFAULT; 973 974 switch (mf->code) { 975 case MEDIA_BUS_FMT_RGB565_2X8_BE: 976 case MEDIA_BUS_FMT_RGB565_2X8_LE: 977 case MEDIA_BUS_FMT_YUYV8_2X8: 978 case MEDIA_BUS_FMT_UYVY8_2X8: 979 case MEDIA_BUS_FMT_YVYU8_2X8: 980 case MEDIA_BUS_FMT_VYUY8_2X8: 981 break; 982 default: 983 mf->code = MEDIA_BUS_FMT_UYVY8_2X8; 984 break; 985 } 986 987 if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE) { 988 struct ov2640_priv *priv = to_ov2640(client); 989 990 if (priv->streaming) { 991 ret = -EBUSY; 992 goto out; 993 } 994 /* select win */ 995 priv->win = win; 996 /* select format */ 997 priv->cfmt_code = mf->code; 998 } else { 999 cfg->try_fmt = *mf; 1000 } 1001out: 1002 mutex_unlock(&priv->lock); 1003 1004 return ret; 1005} 1006 1007static int ov2640_init_cfg(struct v4l2_subdev *sd, 1008 struct v4l2_subdev_pad_config *cfg) 1009{ 1010#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API 1011 struct v4l2_mbus_framefmt *try_fmt = 1012 v4l2_subdev_get_try_format(sd, cfg, 0); 1013 const struct ov2640_win_size *win = 1014 ov2640_select_win(SVGA_WIDTH, SVGA_HEIGHT); 1015 1016 try_fmt->width = win->width; 1017 try_fmt->height = win->height; 1018 try_fmt->code = MEDIA_BUS_FMT_UYVY8_2X8; 1019 try_fmt->colorspace = V4L2_COLORSPACE_SRGB; 1020 try_fmt->field = V4L2_FIELD_NONE; 1021 try_fmt->ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT; 1022 try_fmt->quantization = V4L2_QUANTIZATION_DEFAULT; 1023 try_fmt->xfer_func = V4L2_XFER_FUNC_DEFAULT; 1024#endif 1025 return 0; 1026} 1027 1028static int ov2640_enum_mbus_code(struct v4l2_subdev *sd, 1029 struct v4l2_subdev_pad_config *cfg, 1030 struct v4l2_subdev_mbus_code_enum *code) 1031{ 1032 if (code->pad || code->index >= ARRAY_SIZE(ov2640_codes)) 1033 return -EINVAL; 1034 1035 code->code = ov2640_codes[code->index]; 1036 return 0; 1037} 1038 1039static int ov2640_get_selection(struct v4l2_subdev *sd, 1040 struct v4l2_subdev_pad_config *cfg, 1041 struct v4l2_subdev_selection *sel) 1042{ 1043 if (sel->which != V4L2_SUBDEV_FORMAT_ACTIVE) 1044 return -EINVAL; 1045 1046 switch (sel->target) { 1047 case V4L2_SEL_TGT_CROP_BOUNDS: 1048 case V4L2_SEL_TGT_CROP: 1049 sel->r.left = 0; 1050 sel->r.top = 0; 1051 sel->r.width = UXGA_WIDTH; 1052 sel->r.height = UXGA_HEIGHT; 1053 return 0; 1054 default: 1055 return -EINVAL; 1056 } 1057} 1058 1059static int ov2640_s_stream(struct v4l2_subdev *sd, int on) 1060{ 1061 struct i2c_client *client = v4l2_get_subdevdata(sd); 1062 struct ov2640_priv *priv = to_ov2640(client); 1063 int ret = 0; 1064 1065 mutex_lock(&priv->lock); 1066 if (priv->streaming == !on) { 1067 if (on) { 1068 ret = ov2640_set_params(client, priv->win, 1069 priv->cfmt_code); 1070 if (!ret) 1071 ret = __v4l2_ctrl_handler_setup(&priv->hdl); 1072 } 1073 } 1074 if (!ret) 1075 priv->streaming = on; 1076 mutex_unlock(&priv->lock); 1077 1078 return ret; 1079} 1080 1081static int ov2640_video_probe(struct i2c_client *client) 1082{ 1083 struct ov2640_priv *priv = to_ov2640(client); 1084 u8 pid, ver, midh, midl; 1085 const char *devname; 1086 int ret; 1087 1088 ret = ov2640_s_power(&priv->subdev, 1); 1089 if (ret < 0) 1090 return ret; 1091 1092 /* 1093 * check and show product ID and manufacturer ID 1094 */ 1095 i2c_smbus_write_byte_data(client, BANK_SEL, BANK_SEL_SENS); 1096 pid = i2c_smbus_read_byte_data(client, PID); 1097 ver = i2c_smbus_read_byte_data(client, VER); 1098 midh = i2c_smbus_read_byte_data(client, MIDH); 1099 midl = i2c_smbus_read_byte_data(client, MIDL); 1100 1101 switch (VERSION(pid, ver)) { 1102 case PID_OV2640: 1103 devname = "ov2640"; 1104 break; 1105 default: 1106 dev_err(&client->dev, 1107 "Product ID error %x:%x\n", pid, ver); 1108 ret = -ENODEV; 1109 goto done; 1110 } 1111 1112 dev_info(&client->dev, 1113 "%s Product ID %0x:%0x Manufacturer ID %x:%x\n", 1114 devname, pid, ver, midh, midl); 1115 1116done: 1117 ov2640_s_power(&priv->subdev, 0); 1118 return ret; 1119} 1120 1121static const struct v4l2_ctrl_ops ov2640_ctrl_ops = { 1122 .s_ctrl = ov2640_s_ctrl, 1123}; 1124 1125static const struct v4l2_subdev_core_ops ov2640_subdev_core_ops = { 1126 .log_status = v4l2_ctrl_subdev_log_status, 1127 .subscribe_event = v4l2_ctrl_subdev_subscribe_event, 1128 .unsubscribe_event = v4l2_event_subdev_unsubscribe, 1129#ifdef CONFIG_VIDEO_ADV_DEBUG 1130 .g_register = ov2640_g_register, 1131 .s_register = ov2640_s_register, 1132#endif 1133 .s_power = ov2640_s_power, 1134}; 1135 1136static const struct v4l2_subdev_pad_ops ov2640_subdev_pad_ops = { 1137 .init_cfg = ov2640_init_cfg, 1138 .enum_mbus_code = ov2640_enum_mbus_code, 1139 .get_selection = ov2640_get_selection, 1140 .get_fmt = ov2640_get_fmt, 1141 .set_fmt = ov2640_set_fmt, 1142}; 1143 1144static const struct v4l2_subdev_video_ops ov2640_subdev_video_ops = { 1145 .s_stream = ov2640_s_stream, 1146}; 1147 1148static const struct v4l2_subdev_ops ov2640_subdev_ops = { 1149 .core = &ov2640_subdev_core_ops, 1150 .pad = &ov2640_subdev_pad_ops, 1151 .video = &ov2640_subdev_video_ops, 1152}; 1153 1154static int ov2640_probe_dt(struct i2c_client *client, 1155 struct ov2640_priv *priv) 1156{ 1157 int ret; 1158 1159 /* Request the reset GPIO deasserted */ 1160 priv->resetb_gpio = devm_gpiod_get_optional(&client->dev, "resetb", 1161 GPIOD_OUT_LOW); 1162 1163 if (!priv->resetb_gpio) 1164 dev_dbg(&client->dev, "resetb gpio is not assigned!\n"); 1165 1166 ret = PTR_ERR_OR_ZERO(priv->resetb_gpio); 1167 if (ret && ret != -ENOSYS) { 1168 dev_dbg(&client->dev, 1169 "Error %d while getting resetb gpio\n", ret); 1170 return ret; 1171 } 1172 1173 /* Request the power down GPIO asserted */ 1174 priv->pwdn_gpio = devm_gpiod_get_optional(&client->dev, "pwdn", 1175 GPIOD_OUT_HIGH); 1176 1177 if (!priv->pwdn_gpio) 1178 dev_dbg(&client->dev, "pwdn gpio is not assigned!\n"); 1179 1180 ret = PTR_ERR_OR_ZERO(priv->pwdn_gpio); 1181 if (ret && ret != -ENOSYS) { 1182 dev_dbg(&client->dev, 1183 "Error %d while getting pwdn gpio\n", ret); 1184 return ret; 1185 } 1186 1187 return 0; 1188} 1189 1190/* 1191 * i2c_driver functions 1192 */ 1193static int ov2640_probe(struct i2c_client *client) 1194{ 1195 struct ov2640_priv *priv; 1196 struct i2c_adapter *adapter = client->adapter; 1197 int ret; 1198 1199 if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) { 1200 dev_err(&adapter->dev, 1201 "OV2640: I2C-Adapter doesn't support SMBUS\n"); 1202 return -EIO; 1203 } 1204 1205 priv = devm_kzalloc(&client->dev, sizeof(*priv), GFP_KERNEL); 1206 if (!priv) 1207 return -ENOMEM; 1208 1209 if (client->dev.of_node) { 1210 priv->clk = devm_clk_get(&client->dev, "xvclk"); 1211 if (IS_ERR(priv->clk)) 1212 return PTR_ERR(priv->clk); 1213 ret = clk_prepare_enable(priv->clk); 1214 if (ret) 1215 return ret; 1216 } 1217 1218 ret = ov2640_probe_dt(client, priv); 1219 if (ret) 1220 goto err_clk; 1221 1222 priv->win = ov2640_select_win(SVGA_WIDTH, SVGA_HEIGHT); 1223 priv->cfmt_code = MEDIA_BUS_FMT_UYVY8_2X8; 1224 1225 v4l2_i2c_subdev_init(&priv->subdev, client, &ov2640_subdev_ops); 1226 priv->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | 1227 V4L2_SUBDEV_FL_HAS_EVENTS; 1228 mutex_init(&priv->lock); 1229 v4l2_ctrl_handler_init(&priv->hdl, 3); 1230 priv->hdl.lock = &priv->lock; 1231 v4l2_ctrl_new_std(&priv->hdl, &ov2640_ctrl_ops, 1232 V4L2_CID_VFLIP, 0, 1, 1, 0); 1233 v4l2_ctrl_new_std(&priv->hdl, &ov2640_ctrl_ops, 1234 V4L2_CID_HFLIP, 0, 1, 1, 0); 1235 v4l2_ctrl_new_std_menu_items(&priv->hdl, &ov2640_ctrl_ops, 1236 V4L2_CID_TEST_PATTERN, 1237 ARRAY_SIZE(ov2640_test_pattern_menu) - 1, 0, 0, 1238 ov2640_test_pattern_menu); 1239 priv->subdev.ctrl_handler = &priv->hdl; 1240 if (priv->hdl.error) { 1241 ret = priv->hdl.error; 1242 goto err_hdl; 1243 } 1244#if defined(CONFIG_MEDIA_CONTROLLER) 1245 priv->pad.flags = MEDIA_PAD_FL_SOURCE; 1246 priv->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR; 1247 ret = media_entity_pads_init(&priv->subdev.entity, 1, &priv->pad); 1248 if (ret < 0) 1249 goto err_hdl; 1250#endif 1251 1252 ret = ov2640_video_probe(client); 1253 if (ret < 0) 1254 goto err_videoprobe; 1255 1256 ret = v4l2_async_register_subdev(&priv->subdev); 1257 if (ret < 0) 1258 goto err_videoprobe; 1259 1260 dev_info(&adapter->dev, "OV2640 Probed\n"); 1261 1262 return 0; 1263 1264err_videoprobe: 1265 media_entity_cleanup(&priv->subdev.entity); 1266err_hdl: 1267 v4l2_ctrl_handler_free(&priv->hdl); 1268 mutex_destroy(&priv->lock); 1269err_clk: 1270 clk_disable_unprepare(priv->clk); 1271 return ret; 1272} 1273 1274static int ov2640_remove(struct i2c_client *client) 1275{ 1276 struct ov2640_priv *priv = to_ov2640(client); 1277 1278 v4l2_async_unregister_subdev(&priv->subdev); 1279 v4l2_ctrl_handler_free(&priv->hdl); 1280 mutex_destroy(&priv->lock); 1281 media_entity_cleanup(&priv->subdev.entity); 1282 v4l2_device_unregister_subdev(&priv->subdev); 1283 clk_disable_unprepare(priv->clk); 1284 return 0; 1285} 1286 1287static const struct i2c_device_id ov2640_id[] = { 1288 { "ov2640", 0 }, 1289 { } 1290}; 1291MODULE_DEVICE_TABLE(i2c, ov2640_id); 1292 1293static const struct of_device_id ov2640_of_match[] = { 1294 {.compatible = "ovti,ov2640", }, 1295 {}, 1296}; 1297MODULE_DEVICE_TABLE(of, ov2640_of_match); 1298 1299static struct i2c_driver ov2640_i2c_driver = { 1300 .driver = { 1301 .name = "ov2640", 1302 .of_match_table = of_match_ptr(ov2640_of_match), 1303 }, 1304 .probe_new = ov2640_probe, 1305 .remove = ov2640_remove, 1306 .id_table = ov2640_id, 1307}; 1308 1309module_i2c_driver(ov2640_i2c_driver); 1310 1311MODULE_DESCRIPTION("Driver for Omni Vision 2640 sensor"); 1312MODULE_AUTHOR("Alberto Panizzo"); 1313MODULE_LICENSE("GPL v2"); 1314