1// SPDX-License-Identifier: GPL-2.0-or-later 2/* 3 Conexant cx24120/cx24118 - DVBS/S2 Satellite demod/tuner driver 4 5 Copyright (C) 2008 Patrick Boettcher <pb@linuxtv.org> 6 Copyright (C) 2009 Sergey Tyurin <forum.free-x.de> 7 Updated 2012 by Jannis Achstetter <jannis_achstetter@web.de> 8 Copyright (C) 2015 Jemma Denson <jdenson@gmail.com> 9 April 2015 10 Refactored & simplified driver 11 Updated to work with delivery system supplied by DVBv5 12 Add frequency, fec & pilot to get_frontend 13 14 Cards supported: Technisat Skystar S2 15 16*/ 17 18#include <linux/slab.h> 19#include <linux/kernel.h> 20#include <linux/module.h> 21#include <linux/moduleparam.h> 22#include <linux/init.h> 23#include <linux/firmware.h> 24#include <media/dvb_frontend.h> 25#include "cx24120.h" 26 27#define CX24120_SEARCH_RANGE_KHZ 5000 28#define CX24120_FIRMWARE "dvb-fe-cx24120-1.20.58.2.fw" 29 30/* cx24120 i2c registers */ 31#define CX24120_REG_CMD_START 0x00 /* write cmd_id */ 32#define CX24120_REG_CMD_ARGS 0x01 /* write command arguments */ 33#define CX24120_REG_CMD_END 0x1f /* write 0x01 for end */ 34 35#define CX24120_REG_MAILBOX 0x33 36#define CX24120_REG_FREQ3 0x34 /* frequency */ 37#define CX24120_REG_FREQ2 0x35 38#define CX24120_REG_FREQ1 0x36 39 40#define CX24120_REG_FECMODE 0x39 /* FEC status */ 41#define CX24120_REG_STATUS 0x3a /* Tuner status */ 42#define CX24120_REG_SIGSTR_H 0x3a /* Signal strength high */ 43#define CX24120_REG_SIGSTR_L 0x3b /* Signal strength low byte */ 44#define CX24120_REG_QUALITY_H 0x40 /* SNR high byte */ 45#define CX24120_REG_QUALITY_L 0x41 /* SNR low byte */ 46 47#define CX24120_REG_BER_HH 0x47 /* BER high byte of high word */ 48#define CX24120_REG_BER_HL 0x48 /* BER low byte of high word */ 49#define CX24120_REG_BER_LH 0x49 /* BER high byte of low word */ 50#define CX24120_REG_BER_LL 0x4a /* BER low byte of low word */ 51 52#define CX24120_REG_UCB_H 0x50 /* UCB high byte */ 53#define CX24120_REG_UCB_L 0x51 /* UCB low byte */ 54 55#define CX24120_REG_CLKDIV 0xe6 56#define CX24120_REG_RATEDIV 0xf0 57 58#define CX24120_REG_REVISION 0xff /* Chip revision (ro) */ 59 60/* Command messages */ 61enum command_message_id { 62 CMD_VCO_SET = 0x10, /* cmd.len = 12; */ 63 CMD_TUNEREQUEST = 0x11, /* cmd.len = 15; */ 64 65 CMD_MPEG_ONOFF = 0x13, /* cmd.len = 4; */ 66 CMD_MPEG_INIT = 0x14, /* cmd.len = 7; */ 67 CMD_BANDWIDTH = 0x15, /* cmd.len = 12; */ 68 CMD_CLOCK_READ = 0x16, /* read clock */ 69 CMD_CLOCK_SET = 0x17, /* cmd.len = 10; */ 70 71 CMD_DISEQC_MSG1 = 0x20, /* cmd.len = 11; */ 72 CMD_DISEQC_MSG2 = 0x21, /* cmd.len = d->msg_len + 6; */ 73 CMD_SETVOLTAGE = 0x22, /* cmd.len = 2; */ 74 CMD_SETTONE = 0x23, /* cmd.len = 4; */ 75 CMD_DISEQC_BURST = 0x24, /* cmd.len not used !!! */ 76 77 CMD_READ_SNR = 0x1a, /* Read signal strength */ 78 CMD_START_TUNER = 0x1b, /* ??? */ 79 80 CMD_FWVERSION = 0x35, 81 82 CMD_BER_CTRL = 0x3c, /* cmd.len = 0x03; */ 83}; 84 85#define CX24120_MAX_CMD_LEN 30 86 87/* pilot mask */ 88#define CX24120_PILOT_OFF 0x00 89#define CX24120_PILOT_ON 0x40 90#define CX24120_PILOT_AUTO 0x80 91 92/* signal status */ 93#define CX24120_HAS_SIGNAL 0x01 94#define CX24120_HAS_CARRIER 0x02 95#define CX24120_HAS_VITERBI 0x04 96#define CX24120_HAS_LOCK 0x08 97#define CX24120_HAS_UNK1 0x10 98#define CX24120_HAS_UNK2 0x20 99#define CX24120_STATUS_MASK 0x0f 100#define CX24120_SIGNAL_MASK 0xc0 101 102/* ber window */ 103#define CX24120_BER_WINDOW 16 104#define CX24120_BER_WSIZE ((1 << CX24120_BER_WINDOW) * 208 * 8) 105 106#define info(args...) pr_info("cx24120: " args) 107#define err(args...) pr_err("cx24120: ### ERROR: " args) 108 109/* The Demod/Tuner can't easily provide these, we cache them */ 110struct cx24120_tuning { 111 u32 frequency; 112 u32 symbol_rate; 113 enum fe_spectral_inversion inversion; 114 enum fe_code_rate fec; 115 116 enum fe_delivery_system delsys; 117 enum fe_modulation modulation; 118 enum fe_pilot pilot; 119 120 /* Demod values */ 121 u8 fec_val; 122 u8 fec_mask; 123 u8 clkdiv; 124 u8 ratediv; 125 u8 inversion_val; 126 u8 pilot_val; 127}; 128 129/* Private state */ 130struct cx24120_state { 131 struct i2c_adapter *i2c; 132 const struct cx24120_config *config; 133 struct dvb_frontend frontend; 134 135 u8 cold_init; 136 u8 mpeg_enabled; 137 u8 need_clock_set; 138 139 /* current and next tuning parameters */ 140 struct cx24120_tuning dcur; 141 struct cx24120_tuning dnxt; 142 143 enum fe_status fe_status; 144 145 /* dvbv5 stats calculations */ 146 u32 bitrate; 147 u32 berw_usecs; 148 u32 ber_prev; 149 u32 ucb_offset; 150 unsigned long ber_jiffies_stats; 151 unsigned long per_jiffies_stats; 152}; 153 154/* Command message to firmware */ 155struct cx24120_cmd { 156 u8 id; 157 u8 len; 158 u8 arg[CX24120_MAX_CMD_LEN]; 159}; 160 161/* Read single register */ 162static int cx24120_readreg(struct cx24120_state *state, u8 reg) 163{ 164 int ret; 165 u8 buf = 0; 166 struct i2c_msg msg[] = { 167 { 168 .addr = state->config->i2c_addr, 169 .flags = 0, 170 .len = 1, 171 .buf = ® 172 }, { 173 .addr = state->config->i2c_addr, 174 .flags = I2C_M_RD, 175 .len = 1, 176 .buf = &buf 177 } 178 }; 179 180 ret = i2c_transfer(state->i2c, msg, 2); 181 if (ret != 2) { 182 err("Read error: reg=0x%02x, ret=%i)\n", reg, ret); 183 return ret; 184 } 185 186 dev_dbg(&state->i2c->dev, "reg=0x%02x; data=0x%02x\n", reg, buf); 187 188 return buf; 189} 190 191/* Write single register */ 192static int cx24120_writereg(struct cx24120_state *state, u8 reg, u8 data) 193{ 194 u8 buf[] = { reg, data }; 195 struct i2c_msg msg = { 196 .addr = state->config->i2c_addr, 197 .flags = 0, 198 .buf = buf, 199 .len = 2 200 }; 201 int ret; 202 203 ret = i2c_transfer(state->i2c, &msg, 1); 204 if (ret != 1) { 205 err("Write error: i2c_write error(err == %i, 0x%02x: 0x%02x)\n", 206 ret, reg, data); 207 return ret; 208 } 209 210 dev_dbg(&state->i2c->dev, "reg=0x%02x; data=0x%02x\n", reg, data); 211 212 return 0; 213} 214 215/* Write multiple registers in chunks of i2c_wr_max-sized buffers */ 216static int cx24120_writeregs(struct cx24120_state *state, 217 u8 reg, const u8 *values, u16 len, u8 incr) 218{ 219 int ret; 220 u16 max = state->config->i2c_wr_max > 0 ? 221 state->config->i2c_wr_max : 222 len; 223 224 struct i2c_msg msg = { 225 .addr = state->config->i2c_addr, 226 .flags = 0, 227 }; 228 229 msg.buf = kmalloc(max + 1, GFP_KERNEL); 230 if (!msg.buf) 231 return -ENOMEM; 232 233 while (len) { 234 msg.buf[0] = reg; 235 msg.len = len > max ? max : len; 236 memcpy(&msg.buf[1], values, msg.len); 237 238 len -= msg.len; /* data length revers counter */ 239 values += msg.len; /* incr data pointer */ 240 241 if (incr) 242 reg += msg.len; 243 msg.len++; /* don't forget the addr byte */ 244 245 ret = i2c_transfer(state->i2c, &msg, 1); 246 if (ret != 1) { 247 err("i2c_write error(err == %i, 0x%02x)\n", ret, reg); 248 goto out; 249 } 250 251 dev_dbg(&state->i2c->dev, "reg=0x%02x; data=%*ph\n", 252 reg, msg.len - 1, msg.buf + 1); 253 } 254 255 ret = 0; 256 257out: 258 kfree(msg.buf); 259 return ret; 260} 261 262static const struct dvb_frontend_ops cx24120_ops; 263 264struct dvb_frontend *cx24120_attach(const struct cx24120_config *config, 265 struct i2c_adapter *i2c) 266{ 267 struct cx24120_state *state; 268 int demod_rev; 269 270 info("Conexant cx24120/cx24118 - DVBS/S2 Satellite demod/tuner\n"); 271 state = kzalloc(sizeof(*state), GFP_KERNEL); 272 if (!state) { 273 err("Unable to allocate memory for cx24120_state\n"); 274 goto error; 275 } 276 277 /* setup the state */ 278 state->config = config; 279 state->i2c = i2c; 280 281 /* check if the demod is present and has proper type */ 282 demod_rev = cx24120_readreg(state, CX24120_REG_REVISION); 283 switch (demod_rev) { 284 case 0x07: 285 info("Demod cx24120 rev. 0x07 detected.\n"); 286 break; 287 case 0x05: 288 info("Demod cx24120 rev. 0x05 detected.\n"); 289 break; 290 default: 291 err("Unsupported demod revision: 0x%x detected.\n", demod_rev); 292 goto error; 293 } 294 295 /* create dvb_frontend */ 296 state->cold_init = 0; 297 memcpy(&state->frontend.ops, &cx24120_ops, 298 sizeof(struct dvb_frontend_ops)); 299 state->frontend.demodulator_priv = state; 300 301 info("Conexant cx24120/cx24118 attached.\n"); 302 return &state->frontend; 303 304error: 305 kfree(state); 306 return NULL; 307} 308EXPORT_SYMBOL_GPL(cx24120_attach); 309 310static int cx24120_test_rom(struct cx24120_state *state) 311{ 312 int err, ret; 313 314 err = cx24120_readreg(state, 0xfd); 315 if (err & 4) { 316 ret = cx24120_readreg(state, 0xdf) & 0xfe; 317 err = cx24120_writereg(state, 0xdf, ret); 318 } 319 return err; 320} 321 322static int cx24120_read_snr(struct dvb_frontend *fe, u16 *snr) 323{ 324 struct dtv_frontend_properties *c = &fe->dtv_property_cache; 325 326 if (c->cnr.stat[0].scale != FE_SCALE_DECIBEL) 327 *snr = 0; 328 else 329 *snr = div_s64(c->cnr.stat[0].svalue, 100); 330 331 return 0; 332} 333 334static int cx24120_read_ber(struct dvb_frontend *fe, u32 *ber) 335{ 336 struct cx24120_state *state = fe->demodulator_priv; 337 struct dtv_frontend_properties *c = &fe->dtv_property_cache; 338 339 if (c->post_bit_error.stat[0].scale != FE_SCALE_COUNTER) { 340 *ber = 0; 341 return 0; 342 } 343 344 *ber = c->post_bit_error.stat[0].uvalue - state->ber_prev; 345 state->ber_prev = c->post_bit_error.stat[0].uvalue; 346 347 return 0; 348} 349 350static int cx24120_msg_mpeg_output_global_config(struct cx24120_state *state, 351 u8 flag); 352 353/* Check if we're running a command that needs to disable mpeg out */ 354static void cx24120_check_cmd(struct cx24120_state *state, u8 id) 355{ 356 switch (id) { 357 case CMD_TUNEREQUEST: 358 case CMD_CLOCK_READ: 359 case CMD_DISEQC_MSG1: 360 case CMD_DISEQC_MSG2: 361 case CMD_SETVOLTAGE: 362 case CMD_SETTONE: 363 case CMD_DISEQC_BURST: 364 cx24120_msg_mpeg_output_global_config(state, 0); 365 /* Old driver would do a msleep(100) here */ 366 default: 367 return; 368 } 369} 370 371/* Send a message to the firmware */ 372static int cx24120_message_send(struct cx24120_state *state, 373 struct cx24120_cmd *cmd) 374{ 375 int ficus; 376 377 if (state->mpeg_enabled) { 378 /* Disable mpeg out on certain commands */ 379 cx24120_check_cmd(state, cmd->id); 380 } 381 382 cx24120_writereg(state, CX24120_REG_CMD_START, cmd->id); 383 cx24120_writeregs(state, CX24120_REG_CMD_ARGS, &cmd->arg[0], 384 cmd->len, 1); 385 cx24120_writereg(state, CX24120_REG_CMD_END, 0x01); 386 387 ficus = 1000; 388 while (cx24120_readreg(state, CX24120_REG_CMD_END)) { 389 msleep(20); 390 ficus -= 20; 391 if (ficus == 0) { 392 err("Error sending message to firmware\n"); 393 return -EREMOTEIO; 394 } 395 } 396 dev_dbg(&state->i2c->dev, "sent message 0x%02x\n", cmd->id); 397 398 return 0; 399} 400 401/* Send a message and fill arg[] with the results */ 402static int cx24120_message_sendrcv(struct cx24120_state *state, 403 struct cx24120_cmd *cmd, u8 numreg) 404{ 405 int ret, i; 406 407 if (numreg > CX24120_MAX_CMD_LEN) { 408 err("Too many registers to read. cmd->reg = %d", numreg); 409 return -EREMOTEIO; 410 } 411 412 ret = cx24120_message_send(state, cmd); 413 if (ret != 0) 414 return ret; 415 416 if (!numreg) 417 return 0; 418 419 /* Read numreg registers starting from register cmd->len */ 420 for (i = 0; i < numreg; i++) 421 cmd->arg[i] = cx24120_readreg(state, (cmd->len + i + 1)); 422 423 return 0; 424} 425 426static int cx24120_read_signal_strength(struct dvb_frontend *fe, 427 u16 *signal_strength) 428{ 429 struct dtv_frontend_properties *c = &fe->dtv_property_cache; 430 431 if (c->strength.stat[0].scale != FE_SCALE_RELATIVE) 432 *signal_strength = 0; 433 else 434 *signal_strength = c->strength.stat[0].uvalue; 435 436 return 0; 437} 438 439static int cx24120_msg_mpeg_output_global_config(struct cx24120_state *state, 440 u8 enable) 441{ 442 struct cx24120_cmd cmd; 443 int ret; 444 445 cmd.id = CMD_MPEG_ONOFF; 446 cmd.len = 4; 447 cmd.arg[0] = 0x01; 448 cmd.arg[1] = 0x00; 449 cmd.arg[2] = enable ? 0 : (u8)(-1); 450 cmd.arg[3] = 0x01; 451 452 ret = cx24120_message_send(state, &cmd); 453 if (ret != 0) { 454 dev_dbg(&state->i2c->dev, "failed to %s MPEG output\n", 455 enable ? "enable" : "disable"); 456 return ret; 457 } 458 459 state->mpeg_enabled = enable; 460 dev_dbg(&state->i2c->dev, "MPEG output %s\n", 461 enable ? "enabled" : "disabled"); 462 463 return 0; 464} 465 466static int cx24120_msg_mpeg_output_config(struct cx24120_state *state, u8 seq) 467{ 468 struct cx24120_cmd cmd; 469 struct cx24120_initial_mpeg_config i = 470 state->config->initial_mpeg_config; 471 472 cmd.id = CMD_MPEG_INIT; 473 cmd.len = 7; 474 cmd.arg[0] = seq; /* sequental number - can be 0,1,2 */ 475 cmd.arg[1] = ((i.x1 & 0x01) << 1) | ((i.x1 >> 1) & 0x01); 476 cmd.arg[2] = 0x05; 477 cmd.arg[3] = 0x02; 478 cmd.arg[4] = ((i.x2 >> 1) & 0x01); 479 cmd.arg[5] = (i.x2 & 0xf0) | (i.x3 & 0x0f); 480 cmd.arg[6] = 0x10; 481 482 return cx24120_message_send(state, &cmd); 483} 484 485static int cx24120_diseqc_send_burst(struct dvb_frontend *fe, 486 enum fe_sec_mini_cmd burst) 487{ 488 struct cx24120_state *state = fe->demodulator_priv; 489 struct cx24120_cmd cmd; 490 491 dev_dbg(&state->i2c->dev, "\n"); 492 493 /* 494 * Yes, cmd.len is set to zero. The old driver 495 * didn't specify any len, but also had a 496 * memset 0 before every use of the cmd struct 497 * which would have set it to zero. 498 * This quite probably needs looking into. 499 */ 500 cmd.id = CMD_DISEQC_BURST; 501 cmd.len = 0; 502 cmd.arg[0] = 0x00; 503 cmd.arg[1] = (burst == SEC_MINI_B) ? 0x01 : 0x00; 504 505 return cx24120_message_send(state, &cmd); 506} 507 508static int cx24120_set_tone(struct dvb_frontend *fe, enum fe_sec_tone_mode tone) 509{ 510 struct cx24120_state *state = fe->demodulator_priv; 511 struct cx24120_cmd cmd; 512 513 dev_dbg(&state->i2c->dev, "(%d)\n", tone); 514 515 if ((tone != SEC_TONE_ON) && (tone != SEC_TONE_OFF)) { 516 err("Invalid tone=%d\n", tone); 517 return -EINVAL; 518 } 519 520 cmd.id = CMD_SETTONE; 521 cmd.len = 4; 522 cmd.arg[0] = 0x00; 523 cmd.arg[1] = 0x00; 524 cmd.arg[2] = 0x00; 525 cmd.arg[3] = (tone == SEC_TONE_ON) ? 0x01 : 0x00; 526 527 return cx24120_message_send(state, &cmd); 528} 529 530static int cx24120_set_voltage(struct dvb_frontend *fe, 531 enum fe_sec_voltage voltage) 532{ 533 struct cx24120_state *state = fe->demodulator_priv; 534 struct cx24120_cmd cmd; 535 536 dev_dbg(&state->i2c->dev, "(%d)\n", voltage); 537 538 cmd.id = CMD_SETVOLTAGE; 539 cmd.len = 2; 540 cmd.arg[0] = 0x00; 541 cmd.arg[1] = (voltage == SEC_VOLTAGE_18) ? 0x01 : 0x00; 542 543 return cx24120_message_send(state, &cmd); 544} 545 546static int cx24120_send_diseqc_msg(struct dvb_frontend *fe, 547 struct dvb_diseqc_master_cmd *d) 548{ 549 struct cx24120_state *state = fe->demodulator_priv; 550 struct cx24120_cmd cmd; 551 int back_count; 552 553 dev_dbg(&state->i2c->dev, "\n"); 554 555 cmd.id = CMD_DISEQC_MSG1; 556 cmd.len = 11; 557 cmd.arg[0] = 0x00; 558 cmd.arg[1] = 0x00; 559 cmd.arg[2] = 0x03; 560 cmd.arg[3] = 0x16; 561 cmd.arg[4] = 0x28; 562 cmd.arg[5] = 0x01; 563 cmd.arg[6] = 0x01; 564 cmd.arg[7] = 0x14; 565 cmd.arg[8] = 0x19; 566 cmd.arg[9] = 0x14; 567 cmd.arg[10] = 0x1e; 568 569 if (cx24120_message_send(state, &cmd)) { 570 err("send 1st message(0x%x) failed\n", cmd.id); 571 return -EREMOTEIO; 572 } 573 574 cmd.id = CMD_DISEQC_MSG2; 575 cmd.len = d->msg_len + 6; 576 cmd.arg[0] = 0x00; 577 cmd.arg[1] = 0x01; 578 cmd.arg[2] = 0x02; 579 cmd.arg[3] = 0x00; 580 cmd.arg[4] = 0x00; 581 cmd.arg[5] = d->msg_len; 582 583 memcpy(&cmd.arg[6], &d->msg, d->msg_len); 584 585 if (cx24120_message_send(state, &cmd)) { 586 err("send 2nd message(0x%x) failed\n", cmd.id); 587 return -EREMOTEIO; 588 } 589 590 back_count = 500; 591 do { 592 if (!(cx24120_readreg(state, 0x93) & 0x01)) { 593 dev_dbg(&state->i2c->dev, "diseqc sequence sent\n"); 594 return 0; 595 } 596 msleep(20); 597 back_count -= 20; 598 } while (back_count); 599 600 err("Too long waiting for diseqc.\n"); 601 return -ETIMEDOUT; 602} 603 604static void cx24120_get_stats(struct cx24120_state *state) 605{ 606 struct dvb_frontend *fe = &state->frontend; 607 struct dtv_frontend_properties *c = &fe->dtv_property_cache; 608 struct cx24120_cmd cmd; 609 int ret, cnr, msecs; 610 u16 sig, ucb; 611 u32 ber; 612 613 dev_dbg(&state->i2c->dev, "\n"); 614 615 /* signal strength */ 616 if (state->fe_status & FE_HAS_SIGNAL) { 617 cmd.id = CMD_READ_SNR; 618 cmd.len = 1; 619 cmd.arg[0] = 0x00; 620 621 ret = cx24120_message_send(state, &cmd); 622 if (ret != 0) { 623 err("error reading signal strength\n"); 624 return; 625 } 626 627 /* raw */ 628 sig = cx24120_readreg(state, CX24120_REG_SIGSTR_H) >> 6; 629 sig = sig << 8; 630 sig |= cx24120_readreg(state, CX24120_REG_SIGSTR_L); 631 dev_dbg(&state->i2c->dev, 632 "signal strength from firmware = 0x%x\n", sig); 633 634 /* cooked */ 635 sig = -100 * sig + 94324; 636 637 c->strength.stat[0].scale = FE_SCALE_RELATIVE; 638 c->strength.stat[0].uvalue = sig; 639 } else { 640 c->strength.stat[0].scale = FE_SCALE_NOT_AVAILABLE; 641 } 642 643 /* CNR */ 644 if (state->fe_status & FE_HAS_VITERBI) { 645 cnr = cx24120_readreg(state, CX24120_REG_QUALITY_H) << 8; 646 cnr |= cx24120_readreg(state, CX24120_REG_QUALITY_L); 647 dev_dbg(&state->i2c->dev, "read SNR index = %d\n", cnr); 648 649 /* guessed - seems about right */ 650 cnr = cnr * 100; 651 652 c->cnr.stat[0].scale = FE_SCALE_DECIBEL; 653 c->cnr.stat[0].svalue = cnr; 654 } else { 655 c->cnr.stat[0].scale = FE_SCALE_NOT_AVAILABLE; 656 } 657 658 /* BER & UCB require lock */ 659 if (!(state->fe_status & FE_HAS_LOCK)) { 660 c->post_bit_error.stat[0].scale = FE_SCALE_NOT_AVAILABLE; 661 c->post_bit_count.stat[0].scale = FE_SCALE_NOT_AVAILABLE; 662 c->block_error.stat[0].scale = FE_SCALE_NOT_AVAILABLE; 663 c->block_count.stat[0].scale = FE_SCALE_NOT_AVAILABLE; 664 return; 665 } 666 667 /* BER */ 668 if (time_after(jiffies, state->ber_jiffies_stats)) { 669 msecs = (state->berw_usecs + 500) / 1000; 670 state->ber_jiffies_stats = jiffies + msecs_to_jiffies(msecs); 671 672 ber = cx24120_readreg(state, CX24120_REG_BER_HH) << 24; 673 ber |= cx24120_readreg(state, CX24120_REG_BER_HL) << 16; 674 ber |= cx24120_readreg(state, CX24120_REG_BER_LH) << 8; 675 ber |= cx24120_readreg(state, CX24120_REG_BER_LL); 676 dev_dbg(&state->i2c->dev, "read BER index = %d\n", ber); 677 678 c->post_bit_error.stat[0].scale = FE_SCALE_COUNTER; 679 c->post_bit_error.stat[0].uvalue += ber; 680 681 c->post_bit_count.stat[0].scale = FE_SCALE_COUNTER; 682 c->post_bit_count.stat[0].uvalue += CX24120_BER_WSIZE; 683 } 684 685 /* UCB */ 686 if (time_after(jiffies, state->per_jiffies_stats)) { 687 state->per_jiffies_stats = jiffies + msecs_to_jiffies(1000); 688 689 ucb = cx24120_readreg(state, CX24120_REG_UCB_H) << 8; 690 ucb |= cx24120_readreg(state, CX24120_REG_UCB_L); 691 dev_dbg(&state->i2c->dev, "ucblocks = %d\n", ucb); 692 693 /* handle reset */ 694 if (ucb < state->ucb_offset) 695 state->ucb_offset = c->block_error.stat[0].uvalue; 696 697 c->block_error.stat[0].scale = FE_SCALE_COUNTER; 698 c->block_error.stat[0].uvalue = ucb + state->ucb_offset; 699 700 c->block_count.stat[0].scale = FE_SCALE_COUNTER; 701 c->block_count.stat[0].uvalue += state->bitrate / 8 / 208; 702 } 703} 704 705static void cx24120_set_clock_ratios(struct dvb_frontend *fe); 706 707/* Read current tuning status */ 708static int cx24120_read_status(struct dvb_frontend *fe, enum fe_status *status) 709{ 710 struct cx24120_state *state = fe->demodulator_priv; 711 int lock; 712 713 lock = cx24120_readreg(state, CX24120_REG_STATUS); 714 715 dev_dbg(&state->i2c->dev, "status = 0x%02x\n", lock); 716 717 *status = 0; 718 719 if (lock & CX24120_HAS_SIGNAL) 720 *status = FE_HAS_SIGNAL; 721 if (lock & CX24120_HAS_CARRIER) 722 *status |= FE_HAS_CARRIER; 723 if (lock & CX24120_HAS_VITERBI) 724 *status |= FE_HAS_VITERBI | FE_HAS_SYNC; 725 if (lock & CX24120_HAS_LOCK) 726 *status |= FE_HAS_LOCK; 727 728 /* 729 * TODO: is FE_HAS_SYNC in the right place? 730 * Other cx241xx drivers have this slightly 731 * different 732 */ 733 734 state->fe_status = *status; 735 cx24120_get_stats(state); 736 737 /* Set the clock once tuned in */ 738 if (state->need_clock_set && *status & FE_HAS_LOCK) { 739 /* Set clock ratios */ 740 cx24120_set_clock_ratios(fe); 741 742 /* Old driver would do a msleep(200) here */ 743 744 /* Renable mpeg output */ 745 if (!state->mpeg_enabled) 746 cx24120_msg_mpeg_output_global_config(state, 1); 747 748 state->need_clock_set = 0; 749 } 750 751 return 0; 752} 753 754/* 755 * FEC & modulation lookup table 756 * Used for decoding the REG_FECMODE register 757 * once tuned in. 758 */ 759struct cx24120_modfec { 760 enum fe_delivery_system delsys; 761 enum fe_modulation mod; 762 enum fe_code_rate fec; 763 u8 val; 764}; 765 766static const struct cx24120_modfec modfec_lookup_table[] = { 767 /*delsys mod fec val */ 768 { SYS_DVBS, QPSK, FEC_1_2, 0x01 }, 769 { SYS_DVBS, QPSK, FEC_2_3, 0x02 }, 770 { SYS_DVBS, QPSK, FEC_3_4, 0x03 }, 771 { SYS_DVBS, QPSK, FEC_4_5, 0x04 }, 772 { SYS_DVBS, QPSK, FEC_5_6, 0x05 }, 773 { SYS_DVBS, QPSK, FEC_6_7, 0x06 }, 774 { SYS_DVBS, QPSK, FEC_7_8, 0x07 }, 775 776 { SYS_DVBS2, QPSK, FEC_1_2, 0x04 }, 777 { SYS_DVBS2, QPSK, FEC_3_5, 0x05 }, 778 { SYS_DVBS2, QPSK, FEC_2_3, 0x06 }, 779 { SYS_DVBS2, QPSK, FEC_3_4, 0x07 }, 780 { SYS_DVBS2, QPSK, FEC_4_5, 0x08 }, 781 { SYS_DVBS2, QPSK, FEC_5_6, 0x09 }, 782 { SYS_DVBS2, QPSK, FEC_8_9, 0x0a }, 783 { SYS_DVBS2, QPSK, FEC_9_10, 0x0b }, 784 785 { SYS_DVBS2, PSK_8, FEC_3_5, 0x0c }, 786 { SYS_DVBS2, PSK_8, FEC_2_3, 0x0d }, 787 { SYS_DVBS2, PSK_8, FEC_3_4, 0x0e }, 788 { SYS_DVBS2, PSK_8, FEC_5_6, 0x0f }, 789 { SYS_DVBS2, PSK_8, FEC_8_9, 0x10 }, 790 { SYS_DVBS2, PSK_8, FEC_9_10, 0x11 }, 791}; 792 793/* Retrieve current fec, modulation & pilot values */ 794static int cx24120_get_fec(struct dvb_frontend *fe) 795{ 796 struct dtv_frontend_properties *c = &fe->dtv_property_cache; 797 struct cx24120_state *state = fe->demodulator_priv; 798 int idx; 799 int ret; 800 int fec; 801 802 ret = cx24120_readreg(state, CX24120_REG_FECMODE); 803 fec = ret & 0x3f; /* Lower 6 bits */ 804 805 dev_dbg(&state->i2c->dev, "raw fec = %d\n", fec); 806 807 for (idx = 0; idx < ARRAY_SIZE(modfec_lookup_table); idx++) { 808 if (modfec_lookup_table[idx].delsys != state->dcur.delsys) 809 continue; 810 if (modfec_lookup_table[idx].val != fec) 811 continue; 812 813 break; /* found */ 814 } 815 816 if (idx >= ARRAY_SIZE(modfec_lookup_table)) { 817 dev_dbg(&state->i2c->dev, "couldn't find fec!\n"); 818 return -EINVAL; 819 } 820 821 /* save values back to cache */ 822 c->modulation = modfec_lookup_table[idx].mod; 823 c->fec_inner = modfec_lookup_table[idx].fec; 824 c->pilot = (ret & 0x80) ? PILOT_ON : PILOT_OFF; 825 826 dev_dbg(&state->i2c->dev, "mod(%d), fec(%d), pilot(%d)\n", 827 c->modulation, c->fec_inner, c->pilot); 828 829 return 0; 830} 831 832/* Calculate ber window time */ 833static void cx24120_calculate_ber_window(struct cx24120_state *state, u32 rate) 834{ 835 struct dvb_frontend *fe = &state->frontend; 836 struct dtv_frontend_properties *c = &fe->dtv_property_cache; 837 u64 tmp; 838 839 /* 840 * Calculate bitrate from rate in the clock ratios table. 841 * This isn't *exactly* right but close enough. 842 */ 843 tmp = (u64)c->symbol_rate * rate; 844 do_div(tmp, 256); 845 state->bitrate = tmp; 846 847 /* usecs per ber window */ 848 tmp = 1000000ULL * CX24120_BER_WSIZE; 849 do_div(tmp, state->bitrate); 850 state->berw_usecs = tmp; 851 852 dev_dbg(&state->i2c->dev, "bitrate: %u, berw_usecs: %u\n", 853 state->bitrate, state->berw_usecs); 854} 855 856/* 857 * Clock ratios lookup table 858 * 859 * Values obtained from much larger table in old driver 860 * which had numerous entries which would never match. 861 * 862 * There's probably some way of calculating these but I 863 * can't determine the pattern 864 */ 865struct cx24120_clock_ratios_table { 866 enum fe_delivery_system delsys; 867 enum fe_pilot pilot; 868 enum fe_modulation mod; 869 enum fe_code_rate fec; 870 u32 m_rat; 871 u32 n_rat; 872 u32 rate; 873}; 874 875static const struct cx24120_clock_ratios_table clock_ratios_table[] = { 876 /*delsys pilot mod fec m_rat n_rat rate */ 877 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_1_2, 273088, 254505, 274 }, 878 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_3_5, 17272, 13395, 330 }, 879 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_2_3, 24344, 16967, 367 }, 880 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_3_4, 410788, 254505, 413 }, 881 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_4_5, 438328, 254505, 440 }, 882 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_5_6, 30464, 16967, 459 }, 883 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_8_9, 487832, 254505, 490 }, 884 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_9_10, 493952, 254505, 496 }, 885 { SYS_DVBS2, PILOT_OFF, PSK_8, FEC_3_5, 328168, 169905, 494 }, 886 { SYS_DVBS2, PILOT_OFF, PSK_8, FEC_2_3, 24344, 11327, 550 }, 887 { SYS_DVBS2, PILOT_OFF, PSK_8, FEC_3_4, 410788, 169905, 618 }, 888 { SYS_DVBS2, PILOT_OFF, PSK_8, FEC_5_6, 30464, 11327, 688 }, 889 { SYS_DVBS2, PILOT_OFF, PSK_8, FEC_8_9, 487832, 169905, 735 }, 890 { SYS_DVBS2, PILOT_OFF, PSK_8, FEC_9_10, 493952, 169905, 744 }, 891 { SYS_DVBS2, PILOT_ON, QPSK, FEC_1_2, 273088, 260709, 268 }, 892 { SYS_DVBS2, PILOT_ON, QPSK, FEC_3_5, 328168, 260709, 322 }, 893 { SYS_DVBS2, PILOT_ON, QPSK, FEC_2_3, 121720, 86903, 358 }, 894 { SYS_DVBS2, PILOT_ON, QPSK, FEC_3_4, 410788, 260709, 403 }, 895 { SYS_DVBS2, PILOT_ON, QPSK, FEC_4_5, 438328, 260709, 430 }, 896 { SYS_DVBS2, PILOT_ON, QPSK, FEC_5_6, 152320, 86903, 448 }, 897 { SYS_DVBS2, PILOT_ON, QPSK, FEC_8_9, 487832, 260709, 479 }, 898 { SYS_DVBS2, PILOT_ON, QPSK, FEC_9_10, 493952, 260709, 485 }, 899 { SYS_DVBS2, PILOT_ON, PSK_8, FEC_3_5, 328168, 173853, 483 }, 900 { SYS_DVBS2, PILOT_ON, PSK_8, FEC_2_3, 121720, 57951, 537 }, 901 { SYS_DVBS2, PILOT_ON, PSK_8, FEC_3_4, 410788, 173853, 604 }, 902 { SYS_DVBS2, PILOT_ON, PSK_8, FEC_5_6, 152320, 57951, 672 }, 903 { SYS_DVBS2, PILOT_ON, PSK_8, FEC_8_9, 487832, 173853, 718 }, 904 { SYS_DVBS2, PILOT_ON, PSK_8, FEC_9_10, 493952, 173853, 727 }, 905 { SYS_DVBS, PILOT_OFF, QPSK, FEC_1_2, 152592, 152592, 256 }, 906 { SYS_DVBS, PILOT_OFF, QPSK, FEC_2_3, 305184, 228888, 341 }, 907 { SYS_DVBS, PILOT_OFF, QPSK, FEC_3_4, 457776, 305184, 384 }, 908 { SYS_DVBS, PILOT_OFF, QPSK, FEC_5_6, 762960, 457776, 427 }, 909 { SYS_DVBS, PILOT_OFF, QPSK, FEC_7_8, 1068144, 610368, 448 }, 910}; 911 912/* Set clock ratio from lookup table */ 913static void cx24120_set_clock_ratios(struct dvb_frontend *fe) 914{ 915 struct dtv_frontend_properties *c = &fe->dtv_property_cache; 916 struct cx24120_state *state = fe->demodulator_priv; 917 struct cx24120_cmd cmd; 918 int ret, idx; 919 920 /* Find fec, modulation, pilot */ 921 ret = cx24120_get_fec(fe); 922 if (ret != 0) 923 return; 924 925 /* Find the clock ratios in the lookup table */ 926 for (idx = 0; idx < ARRAY_SIZE(clock_ratios_table); idx++) { 927 if (clock_ratios_table[idx].delsys != state->dcur.delsys) 928 continue; 929 if (clock_ratios_table[idx].mod != c->modulation) 930 continue; 931 if (clock_ratios_table[idx].fec != c->fec_inner) 932 continue; 933 if (clock_ratios_table[idx].pilot != c->pilot) 934 continue; 935 936 break; /* found */ 937 } 938 939 if (idx >= ARRAY_SIZE(clock_ratios_table)) { 940 info("Clock ratio not found - data reception in danger\n"); 941 return; 942 } 943 944 /* Read current values? */ 945 cmd.id = CMD_CLOCK_READ; 946 cmd.len = 1; 947 cmd.arg[0] = 0x00; 948 ret = cx24120_message_sendrcv(state, &cmd, 6); 949 if (ret != 0) 950 return; 951 /* in cmd[0]-[5] - result */ 952 953 dev_dbg(&state->i2c->dev, "m=%d, n=%d; idx: %d m=%d, n=%d, rate=%d\n", 954 cmd.arg[2] | (cmd.arg[1] << 8) | (cmd.arg[0] << 16), 955 cmd.arg[5] | (cmd.arg[4] << 8) | (cmd.arg[3] << 16), 956 idx, 957 clock_ratios_table[idx].m_rat, 958 clock_ratios_table[idx].n_rat, 959 clock_ratios_table[idx].rate); 960 961 /* Set the clock */ 962 cmd.id = CMD_CLOCK_SET; 963 cmd.len = 10; 964 cmd.arg[0] = 0; 965 cmd.arg[1] = 0x10; 966 cmd.arg[2] = (clock_ratios_table[idx].m_rat >> 16) & 0xff; 967 cmd.arg[3] = (clock_ratios_table[idx].m_rat >> 8) & 0xff; 968 cmd.arg[4] = (clock_ratios_table[idx].m_rat >> 0) & 0xff; 969 cmd.arg[5] = (clock_ratios_table[idx].n_rat >> 16) & 0xff; 970 cmd.arg[6] = (clock_ratios_table[idx].n_rat >> 8) & 0xff; 971 cmd.arg[7] = (clock_ratios_table[idx].n_rat >> 0) & 0xff; 972 cmd.arg[8] = (clock_ratios_table[idx].rate >> 8) & 0xff; 973 cmd.arg[9] = (clock_ratios_table[idx].rate >> 0) & 0xff; 974 975 ret = cx24120_message_send(state, &cmd); 976 if (ret != 0) 977 return; 978 979 /* Calculate ber window rates for stat work */ 980 cx24120_calculate_ber_window(state, clock_ratios_table[idx].rate); 981} 982 983/* Set inversion value */ 984static int cx24120_set_inversion(struct cx24120_state *state, 985 enum fe_spectral_inversion inversion) 986{ 987 dev_dbg(&state->i2c->dev, "(%d)\n", inversion); 988 989 switch (inversion) { 990 case INVERSION_OFF: 991 state->dnxt.inversion_val = 0x00; 992 break; 993 case INVERSION_ON: 994 state->dnxt.inversion_val = 0x04; 995 break; 996 case INVERSION_AUTO: 997 state->dnxt.inversion_val = 0x0c; 998 break; 999 default: 1000 return -EINVAL; 1001 } 1002 1003 state->dnxt.inversion = inversion; 1004 1005 return 0; 1006} 1007 1008/* FEC lookup table for tuning */ 1009struct cx24120_modfec_table { 1010 enum fe_delivery_system delsys; 1011 enum fe_modulation mod; 1012 enum fe_code_rate fec; 1013 u8 val; 1014}; 1015 1016static const struct cx24120_modfec_table modfec_table[] = { 1017 /*delsys mod fec val */ 1018 { SYS_DVBS, QPSK, FEC_1_2, 0x2e }, 1019 { SYS_DVBS, QPSK, FEC_2_3, 0x2f }, 1020 { SYS_DVBS, QPSK, FEC_3_4, 0x30 }, 1021 { SYS_DVBS, QPSK, FEC_5_6, 0x31 }, 1022 { SYS_DVBS, QPSK, FEC_6_7, 0x32 }, 1023 { SYS_DVBS, QPSK, FEC_7_8, 0x33 }, 1024 1025 { SYS_DVBS2, QPSK, FEC_1_2, 0x04 }, 1026 { SYS_DVBS2, QPSK, FEC_3_5, 0x05 }, 1027 { SYS_DVBS2, QPSK, FEC_2_3, 0x06 }, 1028 { SYS_DVBS2, QPSK, FEC_3_4, 0x07 }, 1029 { SYS_DVBS2, QPSK, FEC_4_5, 0x08 }, 1030 { SYS_DVBS2, QPSK, FEC_5_6, 0x09 }, 1031 { SYS_DVBS2, QPSK, FEC_8_9, 0x0a }, 1032 { SYS_DVBS2, QPSK, FEC_9_10, 0x0b }, 1033 1034 { SYS_DVBS2, PSK_8, FEC_3_5, 0x0c }, 1035 { SYS_DVBS2, PSK_8, FEC_2_3, 0x0d }, 1036 { SYS_DVBS2, PSK_8, FEC_3_4, 0x0e }, 1037 { SYS_DVBS2, PSK_8, FEC_5_6, 0x0f }, 1038 { SYS_DVBS2, PSK_8, FEC_8_9, 0x10 }, 1039 { SYS_DVBS2, PSK_8, FEC_9_10, 0x11 }, 1040}; 1041 1042/* Set fec_val & fec_mask values from delsys, modulation & fec */ 1043static int cx24120_set_fec(struct cx24120_state *state, enum fe_modulation mod, 1044 enum fe_code_rate fec) 1045{ 1046 int idx; 1047 1048 dev_dbg(&state->i2c->dev, "(0x%02x,0x%02x)\n", mod, fec); 1049 1050 state->dnxt.fec = fec; 1051 1052 /* Lookup fec_val from modfec table */ 1053 for (idx = 0; idx < ARRAY_SIZE(modfec_table); idx++) { 1054 if (modfec_table[idx].delsys != state->dnxt.delsys) 1055 continue; 1056 if (modfec_table[idx].mod != mod) 1057 continue; 1058 if (modfec_table[idx].fec != fec) 1059 continue; 1060 1061 /* found */ 1062 state->dnxt.fec_mask = 0x00; 1063 state->dnxt.fec_val = modfec_table[idx].val; 1064 return 0; 1065 } 1066 1067 if (state->dnxt.delsys == SYS_DVBS2) { 1068 /* DVBS2 auto is 0x00/0x00 */ 1069 state->dnxt.fec_mask = 0x00; 1070 state->dnxt.fec_val = 0x00; 1071 } else { 1072 /* Set DVB-S to auto */ 1073 state->dnxt.fec_val = 0x2e; 1074 state->dnxt.fec_mask = 0xac; 1075 } 1076 1077 return 0; 1078} 1079 1080/* Set pilot */ 1081static int cx24120_set_pilot(struct cx24120_state *state, enum fe_pilot pilot) 1082{ 1083 dev_dbg(&state->i2c->dev, "(%d)\n", pilot); 1084 1085 /* Pilot only valid in DVBS2 */ 1086 if (state->dnxt.delsys != SYS_DVBS2) { 1087 state->dnxt.pilot_val = CX24120_PILOT_OFF; 1088 return 0; 1089 } 1090 1091 switch (pilot) { 1092 case PILOT_OFF: 1093 state->dnxt.pilot_val = CX24120_PILOT_OFF; 1094 break; 1095 case PILOT_ON: 1096 state->dnxt.pilot_val = CX24120_PILOT_ON; 1097 break; 1098 case PILOT_AUTO: 1099 default: 1100 state->dnxt.pilot_val = CX24120_PILOT_AUTO; 1101 } 1102 1103 return 0; 1104} 1105 1106/* Set symbol rate */ 1107static int cx24120_set_symbolrate(struct cx24120_state *state, u32 rate) 1108{ 1109 dev_dbg(&state->i2c->dev, "(%d)\n", rate); 1110 1111 state->dnxt.symbol_rate = rate; 1112 1113 /* Check symbol rate */ 1114 if (rate > 31000000) { 1115 state->dnxt.clkdiv = (-(rate < 31000001) & 3) + 2; 1116 state->dnxt.ratediv = (-(rate < 31000001) & 6) + 4; 1117 } else { 1118 state->dnxt.clkdiv = 3; 1119 state->dnxt.ratediv = 6; 1120 } 1121 1122 return 0; 1123} 1124 1125/* Overwrite the current tuning params, we are about to tune */ 1126static void cx24120_clone_params(struct dvb_frontend *fe) 1127{ 1128 struct cx24120_state *state = fe->demodulator_priv; 1129 1130 state->dcur = state->dnxt; 1131} 1132 1133static int cx24120_set_frontend(struct dvb_frontend *fe) 1134{ 1135 struct dtv_frontend_properties *c = &fe->dtv_property_cache; 1136 struct cx24120_state *state = fe->demodulator_priv; 1137 struct cx24120_cmd cmd; 1138 int ret; 1139 1140 switch (c->delivery_system) { 1141 case SYS_DVBS2: 1142 dev_dbg(&state->i2c->dev, "DVB-S2\n"); 1143 break; 1144 case SYS_DVBS: 1145 dev_dbg(&state->i2c->dev, "DVB-S\n"); 1146 break; 1147 default: 1148 dev_dbg(&state->i2c->dev, 1149 "delivery system(%d) not supported\n", 1150 c->delivery_system); 1151 return -EINVAL; 1152 } 1153 1154 state->dnxt.delsys = c->delivery_system; 1155 state->dnxt.modulation = c->modulation; 1156 state->dnxt.frequency = c->frequency; 1157 state->dnxt.pilot = c->pilot; 1158 1159 ret = cx24120_set_inversion(state, c->inversion); 1160 if (ret != 0) 1161 return ret; 1162 1163 ret = cx24120_set_fec(state, c->modulation, c->fec_inner); 1164 if (ret != 0) 1165 return ret; 1166 1167 ret = cx24120_set_pilot(state, c->pilot); 1168 if (ret != 0) 1169 return ret; 1170 1171 ret = cx24120_set_symbolrate(state, c->symbol_rate); 1172 if (ret != 0) 1173 return ret; 1174 1175 /* discard the 'current' tuning parameters and prepare to tune */ 1176 cx24120_clone_params(fe); 1177 1178 dev_dbg(&state->i2c->dev, 1179 "delsys = %d\n", state->dcur.delsys); 1180 dev_dbg(&state->i2c->dev, 1181 "modulation = %d\n", state->dcur.modulation); 1182 dev_dbg(&state->i2c->dev, 1183 "frequency = %d\n", state->dcur.frequency); 1184 dev_dbg(&state->i2c->dev, 1185 "pilot = %d (val = 0x%02x)\n", 1186 state->dcur.pilot, state->dcur.pilot_val); 1187 dev_dbg(&state->i2c->dev, 1188 "symbol_rate = %d (clkdiv/ratediv = 0x%02x/0x%02x)\n", 1189 state->dcur.symbol_rate, 1190 state->dcur.clkdiv, state->dcur.ratediv); 1191 dev_dbg(&state->i2c->dev, 1192 "FEC = %d (mask/val = 0x%02x/0x%02x)\n", 1193 state->dcur.fec, state->dcur.fec_mask, state->dcur.fec_val); 1194 dev_dbg(&state->i2c->dev, 1195 "Inversion = %d (val = 0x%02x)\n", 1196 state->dcur.inversion, state->dcur.inversion_val); 1197 1198 /* Flag that clock needs to be set after tune */ 1199 state->need_clock_set = 1; 1200 1201 /* Tune in */ 1202 cmd.id = CMD_TUNEREQUEST; 1203 cmd.len = 15; 1204 cmd.arg[0] = 0; 1205 cmd.arg[1] = (state->dcur.frequency & 0xff0000) >> 16; 1206 cmd.arg[2] = (state->dcur.frequency & 0x00ff00) >> 8; 1207 cmd.arg[3] = (state->dcur.frequency & 0x0000ff); 1208 cmd.arg[4] = ((state->dcur.symbol_rate / 1000) & 0xff00) >> 8; 1209 cmd.arg[5] = ((state->dcur.symbol_rate / 1000) & 0x00ff); 1210 cmd.arg[6] = state->dcur.inversion; 1211 cmd.arg[7] = state->dcur.fec_val | state->dcur.pilot_val; 1212 cmd.arg[8] = CX24120_SEARCH_RANGE_KHZ >> 8; 1213 cmd.arg[9] = CX24120_SEARCH_RANGE_KHZ & 0xff; 1214 cmd.arg[10] = 0; /* maybe rolloff? */ 1215 cmd.arg[11] = state->dcur.fec_mask; 1216 cmd.arg[12] = state->dcur.ratediv; 1217 cmd.arg[13] = state->dcur.clkdiv; 1218 cmd.arg[14] = 0; 1219 1220 /* Send tune command */ 1221 ret = cx24120_message_send(state, &cmd); 1222 if (ret != 0) 1223 return ret; 1224 1225 /* Write symbol rate values */ 1226 ret = cx24120_writereg(state, CX24120_REG_CLKDIV, state->dcur.clkdiv); 1227 ret = cx24120_readreg(state, CX24120_REG_RATEDIV); 1228 ret &= 0xfffffff0; 1229 ret |= state->dcur.ratediv; 1230 ret = cx24120_writereg(state, CX24120_REG_RATEDIV, ret); 1231 1232 return 0; 1233} 1234 1235/* Set vco from config */ 1236static int cx24120_set_vco(struct cx24120_state *state) 1237{ 1238 struct cx24120_cmd cmd; 1239 u32 nxtal_khz, vco; 1240 u64 inv_vco; 1241 u32 xtal_khz = state->config->xtal_khz; 1242 1243 nxtal_khz = xtal_khz * 4; 1244 vco = nxtal_khz * 10; 1245 inv_vco = DIV_ROUND_CLOSEST_ULL(0x400000000ULL, vco); 1246 1247 dev_dbg(&state->i2c->dev, "xtal=%d, vco=%d, inv_vco=%lld\n", 1248 xtal_khz, vco, inv_vco); 1249 1250 cmd.id = CMD_VCO_SET; 1251 cmd.len = 12; 1252 cmd.arg[0] = (vco >> 16) & 0xff; 1253 cmd.arg[1] = (vco >> 8) & 0xff; 1254 cmd.arg[2] = vco & 0xff; 1255 cmd.arg[3] = (inv_vco >> 8) & 0xff; 1256 cmd.arg[4] = (inv_vco) & 0xff; 1257 cmd.arg[5] = 0x03; 1258 cmd.arg[6] = (nxtal_khz >> 8) & 0xff; 1259 cmd.arg[7] = nxtal_khz & 0xff; 1260 cmd.arg[8] = 0x06; 1261 cmd.arg[9] = 0x03; 1262 cmd.arg[10] = (xtal_khz >> 16) & 0xff; 1263 cmd.arg[11] = xtal_khz & 0xff; 1264 1265 return cx24120_message_send(state, &cmd); 1266} 1267 1268static int cx24120_init(struct dvb_frontend *fe) 1269{ 1270 const struct firmware *fw; 1271 struct dtv_frontend_properties *c = &fe->dtv_property_cache; 1272 struct cx24120_state *state = fe->demodulator_priv; 1273 struct cx24120_cmd cmd; 1274 u8 reg; 1275 int ret, i; 1276 unsigned char vers[4]; 1277 1278 if (state->cold_init) 1279 return 0; 1280 1281 /* ???? */ 1282 cx24120_writereg(state, 0xea, 0x00); 1283 cx24120_test_rom(state); 1284 reg = cx24120_readreg(state, 0xfb) & 0xfe; 1285 cx24120_writereg(state, 0xfb, reg); 1286 reg = cx24120_readreg(state, 0xfc) & 0xfe; 1287 cx24120_writereg(state, 0xfc, reg); 1288 cx24120_writereg(state, 0xc3, 0x04); 1289 cx24120_writereg(state, 0xc4, 0x04); 1290 cx24120_writereg(state, 0xce, 0x00); 1291 cx24120_writereg(state, 0xcf, 0x00); 1292 reg = cx24120_readreg(state, 0xea) & 0xfe; 1293 cx24120_writereg(state, 0xea, reg); 1294 cx24120_writereg(state, 0xeb, 0x0c); 1295 cx24120_writereg(state, 0xec, 0x06); 1296 cx24120_writereg(state, 0xed, 0x05); 1297 cx24120_writereg(state, 0xee, 0x03); 1298 cx24120_writereg(state, 0xef, 0x05); 1299 cx24120_writereg(state, 0xf3, 0x03); 1300 cx24120_writereg(state, 0xf4, 0x44); 1301 1302 for (i = 0; i < 3; i++) { 1303 cx24120_writereg(state, 0xf0 + i, 0x04); 1304 cx24120_writereg(state, 0xe6 + i, 0x02); 1305 } 1306 1307 cx24120_writereg(state, 0xea, (reg | 0x01)); 1308 for (i = 0; i < 6; i += 2) { 1309 cx24120_writereg(state, 0xc5 + i, 0x00); 1310 cx24120_writereg(state, 0xc6 + i, 0x00); 1311 } 1312 1313 cx24120_writereg(state, 0xe4, 0x03); 1314 cx24120_writereg(state, 0xeb, 0x0a); 1315 1316 dev_dbg(&state->i2c->dev, "requesting firmware (%s) to download...\n", 1317 CX24120_FIRMWARE); 1318 1319 ret = state->config->request_firmware(fe, &fw, CX24120_FIRMWARE); 1320 if (ret) { 1321 err("Could not load firmware (%s): %d\n", CX24120_FIRMWARE, 1322 ret); 1323 return ret; 1324 } 1325 1326 dev_dbg(&state->i2c->dev, 1327 "Firmware found, size %d bytes (%02x %02x .. %02x %02x)\n", 1328 (int)fw->size, /* firmware_size in bytes */ 1329 fw->data[0], /* fw 1st byte */ 1330 fw->data[1], /* fw 2d byte */ 1331 fw->data[fw->size - 2], /* fw before last byte */ 1332 fw->data[fw->size - 1]); /* fw last byte */ 1333 1334 cx24120_test_rom(state); 1335 reg = cx24120_readreg(state, 0xfb) & 0xfe; 1336 cx24120_writereg(state, 0xfb, reg); 1337 cx24120_writereg(state, 0xe0, 0x76); 1338 cx24120_writereg(state, 0xf7, 0x81); 1339 cx24120_writereg(state, 0xf8, 0x00); 1340 cx24120_writereg(state, 0xf9, 0x00); 1341 cx24120_writeregs(state, 0xfa, fw->data, (fw->size - 1), 0x00); 1342 cx24120_writereg(state, 0xf7, 0xc0); 1343 cx24120_writereg(state, 0xe0, 0x00); 1344 reg = (fw->size - 2) & 0x00ff; 1345 cx24120_writereg(state, 0xf8, reg); 1346 reg = ((fw->size - 2) >> 8) & 0x00ff; 1347 cx24120_writereg(state, 0xf9, reg); 1348 cx24120_writereg(state, 0xf7, 0x00); 1349 cx24120_writereg(state, 0xdc, 0x00); 1350 cx24120_writereg(state, 0xdc, 0x07); 1351 msleep(500); 1352 1353 /* Check final byte matches final byte of firmware */ 1354 reg = cx24120_readreg(state, 0xe1); 1355 if (reg == fw->data[fw->size - 1]) { 1356 dev_dbg(&state->i2c->dev, "Firmware uploaded successfully\n"); 1357 ret = 0; 1358 } else { 1359 err("Firmware upload failed. Last byte returned=0x%x\n", ret); 1360 ret = -EREMOTEIO; 1361 } 1362 cx24120_writereg(state, 0xdc, 0x00); 1363 release_firmware(fw); 1364 if (ret != 0) 1365 return ret; 1366 1367 /* Start tuner */ 1368 cmd.id = CMD_START_TUNER; 1369 cmd.len = 3; 1370 cmd.arg[0] = 0x00; 1371 cmd.arg[1] = 0x00; 1372 cmd.arg[2] = 0x00; 1373 1374 if (cx24120_message_send(state, &cmd) != 0) { 1375 err("Error tuner start! :(\n"); 1376 return -EREMOTEIO; 1377 } 1378 1379 /* Set VCO */ 1380 ret = cx24120_set_vco(state); 1381 if (ret != 0) { 1382 err("Error set VCO! :(\n"); 1383 return ret; 1384 } 1385 1386 /* set bandwidth */ 1387 cmd.id = CMD_BANDWIDTH; 1388 cmd.len = 12; 1389 cmd.arg[0] = 0x00; 1390 cmd.arg[1] = 0x00; 1391 cmd.arg[2] = 0x00; 1392 cmd.arg[3] = 0x00; 1393 cmd.arg[4] = 0x05; 1394 cmd.arg[5] = 0x02; 1395 cmd.arg[6] = 0x02; 1396 cmd.arg[7] = 0x00; 1397 cmd.arg[8] = 0x05; 1398 cmd.arg[9] = 0x02; 1399 cmd.arg[10] = 0x02; 1400 cmd.arg[11] = 0x00; 1401 1402 if (cx24120_message_send(state, &cmd)) { 1403 err("Error set bandwidth!\n"); 1404 return -EREMOTEIO; 1405 } 1406 1407 reg = cx24120_readreg(state, 0xba); 1408 if (reg > 3) { 1409 dev_dbg(&state->i2c->dev, "Reset-readreg 0xba: %x\n", ret); 1410 err("Error initialising tuner!\n"); 1411 return -EREMOTEIO; 1412 } 1413 1414 dev_dbg(&state->i2c->dev, "Tuner initialised correctly.\n"); 1415 1416 /* Initialise mpeg outputs */ 1417 cx24120_writereg(state, 0xeb, 0x0a); 1418 if (cx24120_msg_mpeg_output_global_config(state, 0) || 1419 cx24120_msg_mpeg_output_config(state, 0) || 1420 cx24120_msg_mpeg_output_config(state, 1) || 1421 cx24120_msg_mpeg_output_config(state, 2)) { 1422 err("Error initialising mpeg output. :(\n"); 1423 return -EREMOTEIO; 1424 } 1425 1426 /* Set size of BER window */ 1427 cmd.id = CMD_BER_CTRL; 1428 cmd.len = 3; 1429 cmd.arg[0] = 0x00; 1430 cmd.arg[1] = CX24120_BER_WINDOW; 1431 cmd.arg[2] = CX24120_BER_WINDOW; 1432 if (cx24120_message_send(state, &cmd)) { 1433 err("Error setting ber window\n"); 1434 return -EREMOTEIO; 1435 } 1436 1437 /* Firmware CMD 35: Get firmware version */ 1438 cmd.id = CMD_FWVERSION; 1439 cmd.len = 1; 1440 for (i = 0; i < 4; i++) { 1441 cmd.arg[0] = i; 1442 ret = cx24120_message_send(state, &cmd); 1443 if (ret != 0) 1444 return ret; 1445 vers[i] = cx24120_readreg(state, CX24120_REG_MAILBOX); 1446 } 1447 info("FW version %i.%i.%i.%i\n", vers[0], vers[1], vers[2], vers[3]); 1448 1449 /* init stats here in order signal app which stats are supported */ 1450 c->strength.len = 1; 1451 c->strength.stat[0].scale = FE_SCALE_NOT_AVAILABLE; 1452 c->cnr.len = 1; 1453 c->cnr.stat[0].scale = FE_SCALE_NOT_AVAILABLE; 1454 c->post_bit_error.len = 1; 1455 c->post_bit_error.stat[0].scale = FE_SCALE_NOT_AVAILABLE; 1456 c->post_bit_count.len = 1; 1457 c->post_bit_count.stat[0].scale = FE_SCALE_NOT_AVAILABLE; 1458 c->block_error.len = 1; 1459 c->block_error.stat[0].scale = FE_SCALE_NOT_AVAILABLE; 1460 c->block_count.len = 1; 1461 c->block_count.stat[0].scale = FE_SCALE_NOT_AVAILABLE; 1462 1463 state->cold_init = 1; 1464 1465 return 0; 1466} 1467 1468static int cx24120_tune(struct dvb_frontend *fe, bool re_tune, 1469 unsigned int mode_flags, unsigned int *delay, 1470 enum fe_status *status) 1471{ 1472 struct cx24120_state *state = fe->demodulator_priv; 1473 int ret; 1474 1475 dev_dbg(&state->i2c->dev, "(%d)\n", re_tune); 1476 1477 /* TODO: Do we need to set delay? */ 1478 1479 if (re_tune) { 1480 ret = cx24120_set_frontend(fe); 1481 if (ret) 1482 return ret; 1483 } 1484 1485 return cx24120_read_status(fe, status); 1486} 1487 1488static enum dvbfe_algo cx24120_get_algo(struct dvb_frontend *fe) 1489{ 1490 return DVBFE_ALGO_HW; 1491} 1492 1493static int cx24120_sleep(struct dvb_frontend *fe) 1494{ 1495 return 0; 1496} 1497 1498static int cx24120_get_frontend(struct dvb_frontend *fe, 1499 struct dtv_frontend_properties *c) 1500{ 1501 struct cx24120_state *state = fe->demodulator_priv; 1502 u8 freq1, freq2, freq3; 1503 int status; 1504 1505 dev_dbg(&state->i2c->dev, "\n"); 1506 1507 /* don't return empty data if we're not tuned in */ 1508 status = cx24120_readreg(state, CX24120_REG_STATUS); 1509 if (!(status & CX24120_HAS_LOCK)) 1510 return 0; 1511 1512 /* Get frequency */ 1513 freq1 = cx24120_readreg(state, CX24120_REG_FREQ1); 1514 freq2 = cx24120_readreg(state, CX24120_REG_FREQ2); 1515 freq3 = cx24120_readreg(state, CX24120_REG_FREQ3); 1516 c->frequency = (freq3 << 16) | (freq2 << 8) | freq1; 1517 dev_dbg(&state->i2c->dev, "frequency = %d\n", c->frequency); 1518 1519 /* Get modulation, fec, pilot */ 1520 cx24120_get_fec(fe); 1521 1522 return 0; 1523} 1524 1525static void cx24120_release(struct dvb_frontend *fe) 1526{ 1527 struct cx24120_state *state = fe->demodulator_priv; 1528 1529 dev_dbg(&state->i2c->dev, "Clear state structure\n"); 1530 kfree(state); 1531} 1532 1533static int cx24120_read_ucblocks(struct dvb_frontend *fe, u32 *ucblocks) 1534{ 1535 struct cx24120_state *state = fe->demodulator_priv; 1536 struct dtv_frontend_properties *c = &fe->dtv_property_cache; 1537 1538 if (c->block_error.stat[0].scale != FE_SCALE_COUNTER) { 1539 *ucblocks = 0; 1540 return 0; 1541 } 1542 1543 *ucblocks = c->block_error.stat[0].uvalue - state->ucb_offset; 1544 1545 return 0; 1546} 1547 1548static const struct dvb_frontend_ops cx24120_ops = { 1549 .delsys = { SYS_DVBS, SYS_DVBS2 }, 1550 .info = { 1551 .name = "Conexant CX24120/CX24118", 1552 .frequency_min_hz = 950 * MHz, 1553 .frequency_max_hz = 2150 * MHz, 1554 .frequency_stepsize_hz = 1011 * kHz, 1555 .frequency_tolerance_hz = 5 * MHz, 1556 .symbol_rate_min = 1000000, 1557 .symbol_rate_max = 45000000, 1558 .caps = FE_CAN_INVERSION_AUTO | 1559 FE_CAN_FEC_1_2 | FE_CAN_FEC_2_3 | FE_CAN_FEC_3_4 | 1560 FE_CAN_FEC_4_5 | FE_CAN_FEC_5_6 | FE_CAN_FEC_6_7 | 1561 FE_CAN_FEC_7_8 | FE_CAN_FEC_AUTO | 1562 FE_CAN_2G_MODULATION | 1563 FE_CAN_QPSK | FE_CAN_RECOVER 1564 }, 1565 .release = cx24120_release, 1566 1567 .init = cx24120_init, 1568 .sleep = cx24120_sleep, 1569 1570 .tune = cx24120_tune, 1571 .get_frontend_algo = cx24120_get_algo, 1572 .set_frontend = cx24120_set_frontend, 1573 1574 .get_frontend = cx24120_get_frontend, 1575 .read_status = cx24120_read_status, 1576 .read_ber = cx24120_read_ber, 1577 .read_signal_strength = cx24120_read_signal_strength, 1578 .read_snr = cx24120_read_snr, 1579 .read_ucblocks = cx24120_read_ucblocks, 1580 1581 .diseqc_send_master_cmd = cx24120_send_diseqc_msg, 1582 1583 .diseqc_send_burst = cx24120_diseqc_send_burst, 1584 .set_tone = cx24120_set_tone, 1585 .set_voltage = cx24120_set_voltage, 1586}; 1587 1588MODULE_DESCRIPTION("DVB Frontend module for Conexant CX24120/CX24118 hardware"); 1589MODULE_AUTHOR("Jemma Denson"); 1590MODULE_LICENSE("GPL"); 1591