xref: /kernel/linux/linux-5.10/drivers/input/touchscreen/ads7846.c (revision 8c2ecf20)

// SPDX-License-Identifier: GPL-2.0-only
/*
 * ADS7846 based touchscreen and sensor driver
 *
 * Copyright (c) 2005 David Brownell
 * Copyright (c) 2006 Nokia Corporation
 * Various changes: Imre Deak <imre.deak@nokia.com>
 *
 * Using code from:
 *  - corgi_ts.c
 *	Copyright (C) 2004-2005 Richard Purdie
 *  - omap_ts.[hc], ads7846.h, ts_osk.c
 *	Copyright (C) 2002 MontaVista Software
 *	Copyright (C) 2004 Texas Instruments
 *	Copyright (C) 2005 Dirk Behme
 */
#include <linux/types.h>
#include <linux/hwmon.h>
#include <linux/err.h>
#include <linux/sched.h>
#include <linux/delay.h>
#include <linux/input.h>
#include <linux/input/touchscreen.h>
#include <linux/interrupt.h>
#include <linux/slab.h>
#include <linux/pm.h>
#include <linux/of.h>
#include <linux/of_gpio.h>
#include <linux/of_device.h>
#include <linux/gpio.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/regulator/consumer.h>
#include <linux/module.h>
#include <asm/irq.h>
#include <asm/unaligned.h>

/*
 * This code has been heavily tested on a Nokia 770, and lightly
 * tested on other ads7846 devices (OSK/Mistral, Lubbock, Spitz).
 * TSC2046 is just newer ads7846 silicon.
 * Support for ads7843 tested on Atmel at91sam926x-EK.
 * Support for ads7845 has only been stubbed in.
 * Support for Analog Devices AD7873 and AD7843 tested.
 *
 * IRQ handling needs a workaround because of a shortcoming in handling
 * edge triggered IRQs on some platforms like the OMAP1/2. These
 * platforms don't handle the ARM lazy IRQ disabling properly, thus we
 * have to maintain our own SW IRQ disabled status. This should be
 * removed as soon as the affected platform's IRQ handling is fixed.
 *
 * App note sbaa036 talks in more detail about accurate sampling...
 * that ought to help in situations like LCDs inducing noise (which
 * can also be helped by using synch signals) and more generally.
 * This driver tries to utilize the measures described in the app
 * note. The strength of filtering can be set in the board-* specific
 * files.
 */

#define TS_POLL_DELAY	1	/* ms delay before the first sample */
#define TS_POLL_PERIOD	5	/* ms delay between samples */

/* this driver doesn't aim at the peak continuous sample rate */
#define	SAMPLE_BITS	(8 /*cmd*/ + 16 /*sample*/ + 2 /* before, after */)

struct ads7846_buf {
	u8 cmd;
	__be16 data;
} __packed;

struct ads7846_buf_layout {
	unsigned int offset;
	unsigned int count;
	unsigned int skip;
};

/*
 * We allocate this separately to avoid cache line sharing issues when
 * driver is used with DMA-based SPI controllers (like atmel_spi) on
 * systems where main memory is not DMA-coherent (most non-x86 boards).
 */
struct ads7846_packet {
	unsigned int count;
	unsigned int count_skip;
	unsigned int cmds;
	unsigned int last_cmd_idx;
	struct ads7846_buf_layout l[5];
	struct ads7846_buf *rx;
	struct ads7846_buf *tx;

	struct ads7846_buf pwrdown_cmd;

	bool ignore;
	u16 x, y, z1, z2;
};

struct ads7846 {
	struct input_dev	*input;
	char			phys[32];
	char			name[32];

	struct spi_device	*spi;
	struct regulator	*reg;

#if IS_ENABLED(CONFIG_HWMON)
	struct device		*hwmon;
#endif

	u16			model;
	u16			vref_mv;
	u16			vref_delay_usecs;
	u16			x_plate_ohms;
	u16			pressure_max;

	bool			swap_xy;
	bool			use_internal;

	struct ads7846_packet	*packet;

	struct spi_transfer	xfer[18];
	struct spi_message	msg[5];
	int			msg_count;
	wait_queue_head_t	wait;

	bool			pendown;

	int			read_cnt;
	int			read_rep;
	int			last_read;

	u16			debounce_max;
	u16			debounce_tol;
	u16			debounce_rep;

	u16			penirq_recheck_delay_usecs;

	struct touchscreen_properties core_prop;

	struct mutex		lock;
	bool			stopped;	/* P: lock */
	bool			disabled;	/* P: lock */
	bool			suspended;	/* P: lock */

	int			(*filter)(void *data, int data_idx, int *val);
	void			*filter_data;
	void			(*filter_cleanup)(void *data);
	int			(*get_pendown_state)(void);
	int			gpio_pendown;

	void			(*wait_for_sync)(void);
};

/* leave chip selected when we're done, for quicker re-select? */
#if	0
#define	CS_CHANGE(xfer)	((xfer).cs_change = 1)
#else
#define	CS_CHANGE(xfer)	((xfer).cs_change = 0)
#endif

/*--------------------------------------------------------------------------*/

/* The ADS7846 has touchscreen and other sensors.
 * Earlier ads784x chips are somewhat compatible.
 */
#define	ADS_START		(1 << 7)
#define	ADS_A2A1A0_d_y		(1 << 4)	/* differential */
#define	ADS_A2A1A0_d_z1		(3 << 4)	/* differential */
#define	ADS_A2A1A0_d_z2		(4 << 4)	/* differential */
#define	ADS_A2A1A0_d_x		(5 << 4)	/* differential */
#define	ADS_A2A1A0_temp0	(0 << 4)	/* non-differential */
#define	ADS_A2A1A0_vbatt	(2 << 4)	/* non-differential */
#define	ADS_A2A1A0_vaux		(6 << 4)	/* non-differential */
#define	ADS_A2A1A0_temp1	(7 << 4)	/* non-differential */
#define	ADS_8_BIT		(1 << 3)
#define	ADS_12_BIT		(0 << 3)
#define	ADS_SER			(1 << 2)	/* non-differential */
#define	ADS_DFR			(0 << 2)	/* differential */
#define	ADS_PD10_PDOWN		(0 << 0)	/* low power mode + penirq */
#define	ADS_PD10_ADC_ON		(1 << 0)	/* ADC on */
#define	ADS_PD10_REF_ON		(2 << 0)	/* vREF on + penirq */
#define	ADS_PD10_ALL_ON		(3 << 0)	/* ADC + vREF on */

#define	MAX_12BIT	((1<<12)-1)

/* leave ADC powered up (disables penirq) between differential samples */
#define	READ_12BIT_DFR(x, adc, vref) (ADS_START | ADS_A2A1A0_d_ ## x \
	| ADS_12_BIT | ADS_DFR | \
	(adc ? ADS_PD10_ADC_ON : 0) | (vref ? ADS_PD10_REF_ON : 0))

#define	READ_Y(vref)	(READ_12BIT_DFR(y,  1, vref))
#define	READ_Z1(vref)	(READ_12BIT_DFR(z1, 1, vref))
#define	READ_Z2(vref)	(READ_12BIT_DFR(z2, 1, vref))
#define	READ_X(vref)	(READ_12BIT_DFR(x,  1, vref))
#define	PWRDOWN		(READ_12BIT_DFR(y,  0, 0))	/* LAST */

/* single-ended samples need to first power up reference voltage;
 * we leave both ADC and VREF powered
 */
#define	READ_12BIT_SER(x) (ADS_START | ADS_A2A1A0_ ## x \
	| ADS_12_BIT | ADS_SER)

#define	REF_ON	(READ_12BIT_DFR(x, 1, 1))
#define	REF_OFF	(READ_12BIT_DFR(y, 0, 0))

/* Order commands in the most optimal way to reduce Vref switching and
 * settling time:
 * Measure:  X; Vref: X+, X-; IN: Y+
 * Measure:  Y; Vref: Y+, Y-; IN: X+
 * Measure: Z1; Vref: Y+, X-; IN: X+
 * Measure: Z2; Vref: Y+, X-; IN: Y-
 */
enum ads7846_cmds {
	ADS7846_X,
	ADS7846_Y,
	ADS7846_Z1,
	ADS7846_Z2,
	ADS7846_PWDOWN,
};

static int get_pendown_state(struct ads7846 *ts)
{
	if (ts->get_pendown_state)
		return ts->get_pendown_state();

	return !gpio_get_value(ts->gpio_pendown);
}

static void ads7846_report_pen_up(struct ads7846 *ts)
{
	struct input_dev *input = ts->input;

	input_report_key(input, BTN_TOUCH, 0);
	input_report_abs(input, ABS_PRESSURE, 0);
	input_sync(input);

	ts->pendown = false;
	dev_vdbg(&ts->spi->dev, "UP\n");
}

/* Must be called with ts->lock held */
static void ads7846_stop(struct ads7846 *ts)
{
	if (!ts->disabled && !ts->suspended) {
		/* Signal IRQ thread to stop polling and disable the handler. */
		ts->stopped = true;
		mb();
		wake_up(&ts->wait);
		disable_irq(ts->spi->irq);
	}
}

/* Must be called with ts->lock held */
static void ads7846_restart(struct ads7846 *ts)
{
	if (!ts->disabled && !ts->suspended) {
		/* Check if pen was released since last stop */
		if (ts->pendown && !get_pendown_state(ts))
			ads7846_report_pen_up(ts);

		/* Tell IRQ thread that it may poll the device. */
		ts->stopped = false;
		mb();
		enable_irq(ts->spi->irq);
	}
}

/* Must be called with ts->lock held */
static void __ads7846_disable(struct ads7846 *ts)
{
	ads7846_stop(ts);
	regulator_disable(ts->reg);

	/*
	 * We know the chip's in low power mode since we always
	 * leave it that way after every request
	 */
}

/* Must be called with ts->lock held */
static void __ads7846_enable(struct ads7846 *ts)
{
	int error;

	error = regulator_enable(ts->reg);
	if (error != 0)
		dev_err(&ts->spi->dev, "Failed to enable supply: %d\n", error);

	ads7846_restart(ts);
}

static void ads7846_disable(struct ads7846 *ts)
{
	mutex_lock(&ts->lock);

	if (!ts->disabled) {

		if  (!ts->suspended)
			__ads7846_disable(ts);

		ts->disabled = true;
	}

	mutex_unlock(&ts->lock);
}

static void ads7846_enable(struct ads7846 *ts)
{
	mutex_lock(&ts->lock);

	if (ts->disabled) {

		ts->disabled = false;

		if (!ts->suspended)
			__ads7846_enable(ts);
	}

	mutex_unlock(&ts->lock);
}

/*--------------------------------------------------------------------------*/

/*
 * Non-touchscreen sensors only use single-ended conversions.
 * The range is GND..vREF. The ads7843 and ads7835 must use external vREF;
 * ads7846 lets that pin be unconnected, to use internal vREF.
 */

struct ser_req {
	u8			ref_on;
	u8			command;
	u8			ref_off;
	u16			scratch;
	struct spi_message	msg;
	struct spi_transfer	xfer[6];
	/*
	 * DMA (thus cache coherency maintenance) requires the
	 * transfer buffers to live in their own cache lines.
	 */
	__be16 sample ____cacheline_aligned;
};

struct ads7845_ser_req {
	u8			command[3];
	struct spi_message	msg;
	struct spi_transfer	xfer[2];
	/*
	 * DMA (thus cache coherency maintenance) requires the
	 * transfer buffers to live in their own cache lines.
	 */
	u8 sample[3] ____cacheline_aligned;
};

static int ads7846_read12_ser(struct device *dev, unsigned command)
{
	struct spi_device *spi = to_spi_device(dev);
	struct ads7846 *ts = dev_get_drvdata(dev);
	struct ser_req *req;
	int status;

	req = kzalloc(sizeof *req, GFP_KERNEL);
	if (!req)
		return -ENOMEM;

	spi_message_init(&req->msg);

	/* maybe turn on internal vREF, and let it settle */
	if (ts->use_internal) {
		req->ref_on = REF_ON;
		req->xfer[0].tx_buf = &req->ref_on;
		req->xfer[0].len = 1;
		spi_message_add_tail(&req->xfer[0], &req->msg);

		req->xfer[1].rx_buf = &req->scratch;
		req->xfer[1].len = 2;

		/* for 1uF, settle for 800 usec; no cap, 100 usec.  */
		req->xfer[1].delay.value = ts->vref_delay_usecs;
		req->xfer[1].delay.unit = SPI_DELAY_UNIT_USECS;
		spi_message_add_tail(&req->xfer[1], &req->msg);

		/* Enable reference voltage */
		command |= ADS_PD10_REF_ON;
	}

	/* Enable ADC in every case */
	command |= ADS_PD10_ADC_ON;

	/* take sample */
	req->command = (u8) command;
	req->xfer[2].tx_buf = &req->command;
	req->xfer[2].len = 1;
	spi_message_add_tail(&req->xfer[2], &req->msg);

	req->xfer[3].rx_buf = &req->sample;
	req->xfer[3].len = 2;
	spi_message_add_tail(&req->xfer[3], &req->msg);

	/* REVISIT:  take a few more samples, and compare ... */

	/* converter in low power mode & enable PENIRQ */
	req->ref_off = PWRDOWN;
	req->xfer[4].tx_buf = &req->ref_off;
	req->xfer[4].len = 1;
	spi_message_add_tail(&req->xfer[4], &req->msg);

	req->xfer[5].rx_buf = &req->scratch;
	req->xfer[5].len = 2;
	CS_CHANGE(req->xfer[5]);
	spi_message_add_tail(&req->xfer[5], &req->msg);

	mutex_lock(&ts->lock);
	ads7846_stop(ts);
	status = spi_sync(spi, &req->msg);
	ads7846_restart(ts);
	mutex_unlock(&ts->lock);

	if (status == 0) {
		/* on-wire is a must-ignore bit, a BE12 value, then padding */
		status = be16_to_cpu(req->sample);
		status = status >> 3;
		status &= 0x0fff;
	}

	kfree(req);
	return status;
}

static int ads7845_read12_ser(struct device *dev, unsigned command)
{
	struct spi_device *spi = to_spi_device(dev);
	struct ads7846 *ts = dev_get_drvdata(dev);
	struct ads7845_ser_req *req;
	int status;

	req = kzalloc(sizeof *req, GFP_KERNEL);
	if (!req)
		return -ENOMEM;

	spi_message_init(&req->msg);

	req->command[0] = (u8) command;
	req->xfer[0].tx_buf = req->command;
	req->xfer[0].rx_buf = req->sample;
	req->xfer[0].len = 3;
	spi_message_add_tail(&req->xfer[0], &req->msg);

	mutex_lock(&ts->lock);
	ads7846_stop(ts);
	status = spi_sync(spi, &req->msg);
	ads7846_restart(ts);
	mutex_unlock(&ts->lock);

	if (status == 0) {
		/* BE12 value, then padding */
		status = get_unaligned_be16(&req->sample[1]);
		status = status >> 3;
		status &= 0x0fff;
	}

	kfree(req);
	return status;
}

#if IS_ENABLED(CONFIG_HWMON)

#define SHOW(name, var, adjust) static ssize_t \
name ## _show(struct device *dev, struct device_attribute *attr, char *buf) \
{ \
	struct ads7846 *ts = dev_get_drvdata(dev); \
	ssize_t v = ads7846_read12_ser(&ts->spi->dev, \
			READ_12BIT_SER(var)); \
	if (v < 0) \
		return v; \
	return sprintf(buf, "%u\n", adjust(ts, v)); \
} \
static DEVICE_ATTR(name, S_IRUGO, name ## _show, NULL);


/* Sysfs conventions report temperatures in millidegrees Celsius.
 * ADS7846 could use the low-accuracy two-sample scheme, but can't do the high
 * accuracy scheme without calibration data.  For now we won't try either;
 * userspace sees raw sensor values, and must scale/calibrate appropriately.
 */
static inline unsigned null_adjust(struct ads7846 *ts, ssize_t v)
{
	return v;
}

SHOW(temp0, temp0, null_adjust)		/* temp1_input */
SHOW(temp1, temp1, null_adjust)		/* temp2_input */


/* sysfs conventions report voltages in millivolts.  We can convert voltages
 * if we know vREF.  userspace may need to scale vAUX to match the board's
 * external resistors; we assume that vBATT only uses the internal ones.
 */
static inline unsigned vaux_adjust(struct ads7846 *ts, ssize_t v)
{
	unsigned retval = v;

	/* external resistors may scale vAUX into 0..vREF */
	retval *= ts->vref_mv;
	retval = retval >> 12;

	return retval;
}

static inline unsigned vbatt_adjust(struct ads7846 *ts, ssize_t v)
{
	unsigned retval = vaux_adjust(ts, v);

	/* ads7846 has a resistor ladder to scale this signal down */
	if (ts->model == 7846)
		retval *= 4;

	return retval;
}

SHOW(in0_input, vaux, vaux_adjust)
SHOW(in1_input, vbatt, vbatt_adjust)

static umode_t ads7846_is_visible(struct kobject *kobj, struct attribute *attr,
				  int index)
{
	struct device *dev = container_of(kobj, struct device, kobj);
	struct ads7846 *ts = dev_get_drvdata(dev);

	if (ts->model == 7843 && index < 2)	/* in0, in1 */
		return 0;
	if (ts->model == 7845 && index != 2)	/* in0 */
		return 0;

	return attr->mode;
}

static struct attribute *ads7846_attributes[] = {
	&dev_attr_temp0.attr,		/* 0 */
	&dev_attr_temp1.attr,		/* 1 */
	&dev_attr_in0_input.attr,	/* 2 */
	&dev_attr_in1_input.attr,	/* 3 */
	NULL,
};

static const struct attribute_group ads7846_attr_group = {
	.attrs = ads7846_attributes,
	.is_visible = ads7846_is_visible,
};
__ATTRIBUTE_GROUPS(ads7846_attr);

static int ads784x_hwmon_register(struct spi_device *spi, struct ads7846 *ts)
{
	/* hwmon sensors need a reference voltage */
	switch (ts->model) {
	case 7846:
		if (!ts->vref_mv) {
			dev_dbg(&spi->dev, "assuming 2.5V internal vREF\n");
			ts->vref_mv = 2500;
			ts->use_internal = true;
		}
		break;
	case 7845:
	case 7843:
		if (!ts->vref_mv) {
			dev_warn(&spi->dev,
				"external vREF for ADS%d not specified\n",
				ts->model);
			return 0;
		}
		break;
	}

	ts->hwmon = hwmon_device_register_with_groups(&spi->dev, spi->modalias,
						      ts, ads7846_attr_groups);

	return PTR_ERR_OR_ZERO(ts->hwmon);
}

static void ads784x_hwmon_unregister(struct spi_device *spi,
				     struct ads7846 *ts)
{
	if (ts->hwmon)
		hwmon_device_unregister(ts->hwmon);
}

#else
static inline int ads784x_hwmon_register(struct spi_device *spi,
					 struct ads7846 *ts)
{
	return 0;
}

static inline void ads784x_hwmon_unregister(struct spi_device *spi,
					    struct ads7846 *ts)
{
}
#endif

static ssize_t ads7846_pen_down_show(struct device *dev,
				     struct device_attribute *attr, char *buf)
{
	struct ads7846 *ts = dev_get_drvdata(dev);

	return sprintf(buf, "%u\n", ts->pendown);
}

static DEVICE_ATTR(pen_down, S_IRUGO, ads7846_pen_down_show, NULL);

static ssize_t ads7846_disable_show(struct device *dev,
				     struct device_attribute *attr, char *buf)
{
	struct ads7846 *ts = dev_get_drvdata(dev);

	return sprintf(buf, "%u\n", ts->disabled);
}

static ssize_t ads7846_disable_store(struct device *dev,
				     struct device_attribute *attr,
				     const char *buf, size_t count)
{
	struct ads7846 *ts = dev_get_drvdata(dev);
	unsigned int i;
	int err;

	err = kstrtouint(buf, 10, &i);
	if (err)
		return err;

	if (i)
		ads7846_disable(ts);
	else
		ads7846_enable(ts);

	return count;
}

static DEVICE_ATTR(disable, 0664, ads7846_disable_show, ads7846_disable_store);

static struct attribute *ads784x_attributes[] = {
	&dev_attr_pen_down.attr,
	&dev_attr_disable.attr,
	NULL,
};

static const struct attribute_group ads784x_attr_group = {
	.attrs = ads784x_attributes,
};

/*--------------------------------------------------------------------------*/

static void null_wait_for_sync(void)
{
}

static int ads7846_debounce_filter(void *ads, int data_idx, int *val)
{
	struct ads7846 *ts = ads;

	if (!ts->read_cnt || (abs(ts->last_read - *val) > ts->debounce_tol)) {
		/* Start over collecting consistent readings. */
		ts->read_rep = 0;
		/*
		 * Repeat it, if this was the first read or the read
		 * wasn't consistent enough.
		 */
		if (ts->read_cnt < ts->debounce_max) {
			ts->last_read = *val;
			ts->read_cnt++;
			return ADS7846_FILTER_REPEAT;
		} else {
			/*
			 * Maximum number of debouncing reached and still
			 * not enough number of consistent readings. Abort
			 * the whole sample, repeat it in the next sampling
			 * period.
			 */
			ts->read_cnt = 0;
			return ADS7846_FILTER_IGNORE;
		}
	} else {
		if (++ts->read_rep > ts->debounce_rep) {
			/*
			 * Got a good reading for this coordinate,
			 * go for the next one.
			 */
			ts->read_cnt = 0;
			ts->read_rep = 0;
			return ADS7846_FILTER_OK;
		} else {
			/* Read more values that are consistent. */
			ts->read_cnt++;
			return ADS7846_FILTER_REPEAT;
		}
	}
}

static int ads7846_no_filter(void *ads, int data_idx, int *val)
{
	return ADS7846_FILTER_OK;
}

static int ads7846_get_value(struct ads7846_buf *buf)
{
	int value;

	value = be16_to_cpup(&buf->data);

	/* enforce ADC output is 12 bits width */
	return (value >> 3) & 0xfff;
}

static void ads7846_set_cmd_val(struct ads7846 *ts, enum ads7846_cmds cmd_idx,
				u16 val)
{
	struct ads7846_packet *packet = ts->packet;

	switch (cmd_idx) {
	case ADS7846_Y:
		packet->y = val;
		break;
	case ADS7846_X:
		packet->x = val;
		break;
	case ADS7846_Z1:
		packet->z1 = val;
		break;
	case ADS7846_Z2:
		packet->z2 = val;
		break;
	default:
		WARN_ON_ONCE(1);
	}
}

static u8 ads7846_get_cmd(enum ads7846_cmds cmd_idx, int vref)
{
	switch (cmd_idx) {
	case ADS7846_Y:
		return READ_Y(vref);
	case ADS7846_X:
		return READ_X(vref);

	/* 7846 specific commands  */
	case ADS7846_Z1:
		return READ_Z1(vref);
	case ADS7846_Z2:
		return READ_Z2(vref);
	case ADS7846_PWDOWN:
		return PWRDOWN;
	default:
		WARN_ON_ONCE(1);
	}

	return 0;
}

static bool ads7846_cmd_need_settle(enum ads7846_cmds cmd_idx)
{
	switch (cmd_idx) {
	case ADS7846_X:
	case ADS7846_Y:
	case ADS7846_Z1:
	case ADS7846_Z2:
		return true;
	case ADS7846_PWDOWN:
		return false;
	default:
		WARN_ON_ONCE(1);
	}

	return false;
}

static int ads7846_filter(struct ads7846 *ts)
{
	struct ads7846_packet *packet = ts->packet;
	int action;
	int val;
	unsigned int cmd_idx, b;

	packet->ignore = false;
	for (cmd_idx = packet->last_cmd_idx; cmd_idx < packet->cmds - 1; cmd_idx++) {
		struct ads7846_buf_layout *l = &packet->l[cmd_idx];

		packet->last_cmd_idx = cmd_idx;

		for (b = l->skip; b < l->count; b++) {
			val = ads7846_get_value(&packet->rx[l->offset + b]);

			action = ts->filter(ts->filter_data, cmd_idx, &val);
			if (action == ADS7846_FILTER_REPEAT) {
				if (b == l->count - 1)
					return -EAGAIN;
			} else if (action == ADS7846_FILTER_OK) {
				ads7846_set_cmd_val(ts, cmd_idx, val);
				break;
			} else {
				packet->ignore = true;
				return 0;
			}
		}
	}

	return 0;
}

static void ads7846_read_state(struct ads7846 *ts)
{
	struct ads7846_packet *packet = ts->packet;
	struct spi_message *m;
	int msg_idx = 0;
	int error;

	packet->last_cmd_idx = 0;

	while (true) {
		ts->wait_for_sync();

		m = &ts->msg[msg_idx];
		error = spi_sync(ts->spi, m);
		if (error) {
			dev_err(&ts->spi->dev, "spi_sync --> %d\n", error);
			packet->ignore = true;
			return;
		}

		error = ads7846_filter(ts);
		if (error)
			continue;

		return;
	}
}

static void ads7846_report_state(struct ads7846 *ts)
{
	struct ads7846_packet *packet = ts->packet;
	unsigned int Rt;
	u16 x, y, z1, z2;

	x = packet->x;
	y = packet->y;
	if (ts->model == 7845) {
		z1 = 0;
		z2 = 0;
	} else {
		z1 = packet->z1;
		z2 = packet->z2;
	}

	/* range filtering */
	if (x == MAX_12BIT)
		x = 0;

	if (ts->model == 7843 || ts->model == 7845) {
		Rt = ts->pressure_max / 2;
	} else if (likely(x && z1)) {
		/* compute touch pressure resistance using equation #2 */
		Rt = z2;
		Rt -= z1;
		Rt *= ts->x_plate_ohms;
		Rt = DIV_ROUND_CLOSEST(Rt, 16);
		Rt *= x;
		Rt /= z1;
		Rt = DIV_ROUND_CLOSEST(Rt, 256);
	} else {
		Rt = 0;
	}

	/*
	 * Sample found inconsistent by debouncing or pressure is beyond
	 * the maximum. Don't report it to user space, repeat at least
	 * once more the measurement
	 */
	if (packet->ignore || Rt > ts->pressure_max) {
		dev_vdbg(&ts->spi->dev, "ignored %d pressure %d\n",
			 packet->ignore, Rt);
		return;
	}

	/*
	 * Maybe check the pendown state before reporting. This discards
	 * false readings when the pen is lifted.
	 */
	if (ts->penirq_recheck_delay_usecs) {
		udelay(ts->penirq_recheck_delay_usecs);
		if (!get_pendown_state(ts))
			Rt = 0;
	}

	/*
	 * NOTE: We can't rely on the pressure to determine the pen down
	 * state, even this controller has a pressure sensor. The pressure
	 * value can fluctuate for quite a while after lifting the pen and
	 * in some cases may not even settle at the expected value.
	 *
	 * The only safe way to check for the pen up condition is in the
	 * timer by reading the pen signal state (it's a GPIO _and_ IRQ).
	 */
	if (Rt) {
		struct input_dev *input = ts->input;

		if (!ts->pendown) {
			input_report_key(input, BTN_TOUCH, 1);
			ts->pendown = true;
			dev_vdbg(&ts->spi->dev, "DOWN\n");
		}

		touchscreen_report_pos(input, &ts->core_prop, x, y, false);
		input_report_abs(input, ABS_PRESSURE, ts->pressure_max - Rt);

		input_sync(input);
		dev_vdbg(&ts->spi->dev, "%4d/%4d/%4d\n", x, y, Rt);
	}
}

static irqreturn_t ads7846_hard_irq(int irq, void *handle)
{
	struct ads7846 *ts = handle;

	return get_pendown_state(ts) ? IRQ_WAKE_THREAD : IRQ_HANDLED;
}


static irqreturn_t ads7846_irq(int irq, void *handle)
{
	struct ads7846 *ts = handle;

	/* Start with a small delay before checking pendown state */
	msleep(TS_POLL_DELAY);

	while (!ts->stopped && get_pendown_state(ts)) {

		/* pen is down, continue with the measurement */
		ads7846_read_state(ts);

		if (!ts->stopped)
			ads7846_report_state(ts);

		wait_event_timeout(ts->wait, ts->stopped,
				   msecs_to_jiffies(TS_POLL_PERIOD));
	}

	if (ts->pendown && !ts->stopped)
		ads7846_report_pen_up(ts);

	return IRQ_HANDLED;
}

static int __maybe_unused ads7846_suspend(struct device *dev)
{
	struct ads7846 *ts = dev_get_drvdata(dev);

	mutex_lock(&ts->lock);

	if (!ts->suspended) {

		if (!ts->disabled)
			__ads7846_disable(ts);

		if (device_may_wakeup(&ts->spi->dev))
			enable_irq_wake(ts->spi->irq);

		ts->suspended = true;
	}

	mutex_unlock(&ts->lock);

	return 0;
}

static int __maybe_unused ads7846_resume(struct device *dev)
{
	struct ads7846 *ts = dev_get_drvdata(dev);

	mutex_lock(&ts->lock);

	if (ts->suspended) {

		ts->suspended = false;

		if (device_may_wakeup(&ts->spi->dev))
			disable_irq_wake(ts->spi->irq);

		if (!ts->disabled)
			__ads7846_enable(ts);
	}

	mutex_unlock(&ts->lock);

	return 0;
}

static SIMPLE_DEV_PM_OPS(ads7846_pm, ads7846_suspend, ads7846_resume);

static int ads7846_setup_pendown(struct spi_device *spi,
				 struct ads7846 *ts,
				 const struct ads7846_platform_data *pdata)
{
	int err;

	/*
	 * REVISIT when the irq can be triggered active-low, or if for some
	 * reason the touchscreen isn't hooked up, we don't need to access
	 * the pendown state.
	 */

	if (pdata->get_pendown_state) {
		ts->get_pendown_state = pdata->get_pendown_state;
	} else if (gpio_is_valid(pdata->gpio_pendown)) {

		err = gpio_request_one(pdata->gpio_pendown, GPIOF_IN,
				       "ads7846_pendown");
		if (err) {
			dev_err(&spi->dev,
				"failed to request/setup pendown GPIO%d: %d\n",
				pdata->gpio_pendown, err);
			return err;
		}

		ts->gpio_pendown = pdata->gpio_pendown;

		if (pdata->gpio_pendown_debounce)
			gpio_set_debounce(pdata->gpio_pendown,
					  pdata->gpio_pendown_debounce);
	} else {
		dev_err(&spi->dev, "no get_pendown_state nor gpio_pendown?\n");
		return -EINVAL;
	}

	return 0;
}

/*
 * Set up the transfers to read touchscreen state; this assumes we
 * use formula #2 for pressure, not #3.
 */
static int ads7846_setup_spi_msg(struct ads7846 *ts,
				  const struct ads7846_platform_data *pdata)
{
	struct spi_message *m = &ts->msg[0];
	struct spi_transfer *x = ts->xfer;
	struct ads7846_packet *packet = ts->packet;
	int vref = pdata->keep_vref_on;
	unsigned int count, offset = 0;
	unsigned int cmd_idx, b;
	unsigned long time;
	size_t size = 0;

	/* time per bit */
	time = NSEC_PER_SEC / ts->spi->max_speed_hz;

	count = pdata->settle_delay_usecs * NSEC_PER_USEC / time;
	packet->count_skip = DIV_ROUND_UP(count, 24);

	if (ts->debounce_max && ts->debounce_rep)
		/* ads7846_debounce_filter() is making ts->debounce_rep + 2
		 * reads. So we need to get all samples for normal case. */
		packet->count = ts->debounce_rep + 2;
	else
		packet->count = 1;

	if (ts->model == 7846)
		packet->cmds = 5; /* x, y, z1, z2, pwdown */
	else
		packet->cmds = 3; /* x, y, pwdown */

	for (cmd_idx = 0; cmd_idx < packet->cmds; cmd_idx++) {
		struct ads7846_buf_layout *l = &packet->l[cmd_idx];
		unsigned int max_count;

		if (cmd_idx == packet->cmds - 1)
			cmd_idx = ADS7846_PWDOWN;

		if (ads7846_cmd_need_settle(cmd_idx))
			max_count = packet->count + packet->count_skip;
		else
			max_count = packet->count;

		l->offset = offset;
		offset += max_count;
		l->count = max_count;
		l->skip = packet->count_skip;
		size += sizeof(*packet->tx) * max_count;
	}

	packet->tx = devm_kzalloc(&ts->spi->dev, size, GFP_KERNEL);
	if (!packet->tx)
		return -ENOMEM;

	packet->rx = devm_kzalloc(&ts->spi->dev, size, GFP_KERNEL);
	if (!packet->rx)
		return -ENOMEM;

	if (ts->model == 7873) {
		/*
		 * The AD7873 is almost identical to the ADS7846
		 * keep VREF off during differential/ratiometric
		 * conversion modes.
		 */
		ts->model = 7846;
		vref = 0;
	}

	ts->msg_count = 1;
	spi_message_init(m);
	m->context = ts;

	for (cmd_idx = 0; cmd_idx < packet->cmds; cmd_idx++) {
		struct ads7846_buf_layout *l = &packet->l[cmd_idx];
		u8 cmd;

		if (cmd_idx == packet->cmds - 1)
			cmd_idx = ADS7846_PWDOWN;

		cmd = ads7846_get_cmd(cmd_idx, vref);

		for (b = 0; b < l->count; b++)
			packet->tx[l->offset + b].cmd = cmd;
	}

	x->tx_buf = packet->tx;
	x->rx_buf = packet->rx;
	x->len = size;
	spi_message_add_tail(x, m);

	return 0;
}

#ifdef CONFIG_OF
static const struct of_device_id ads7846_dt_ids[] = {
	{ .compatible = "ti,tsc2046",	.data = (void *) 7846 },
	{ .compatible = "ti,ads7843",	.data = (void *) 7843 },
	{ .compatible = "ti,ads7845",	.data = (void *) 7845 },
	{ .compatible = "ti,ads7846",	.data = (void *) 7846 },
	{ .compatible = "ti,ads7873",	.data = (void *) 7873 },
	{ }
};
MODULE_DEVICE_TABLE(of, ads7846_dt_ids);

static const struct ads7846_platform_data *ads7846_probe_dt(struct device *dev)
{
	struct ads7846_platform_data *pdata;
	struct device_node *node = dev->of_node;
	const struct of_device_id *match;
	u32 value;

	if (!node) {
		dev_err(dev, "Device does not have associated DT data\n");
		return ERR_PTR(-EINVAL);
	}

	match = of_match_device(ads7846_dt_ids, dev);
	if (!match) {
		dev_err(dev, "Unknown device model\n");
		return ERR_PTR(-EINVAL);
	}

	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
	if (!pdata)
		return ERR_PTR(-ENOMEM);

	pdata->model = (unsigned long)match->data;

	of_property_read_u16(node, "ti,vref-delay-usecs",
			     &pdata->vref_delay_usecs);
	of_property_read_u16(node, "ti,vref-mv", &pdata->vref_mv);
	pdata->keep_vref_on = of_property_read_bool(node, "ti,keep-vref-on");

	pdata->swap_xy = of_property_read_bool(node, "ti,swap-xy");

	of_property_read_u16(node, "ti,settle-delay-usec",
			     &pdata->settle_delay_usecs);
	of_property_read_u16(node, "ti,penirq-recheck-delay-usecs",
			     &pdata->penirq_recheck_delay_usecs);

	of_property_read_u16(node, "ti,x-plate-ohms", &pdata->x_plate_ohms);
	of_property_read_u16(node, "ti,y-plate-ohms", &pdata->y_plate_ohms);

	of_property_read_u16(node, "ti,x-min", &pdata->x_min);
	of_property_read_u16(node, "ti,y-min", &pdata->y_min);
	of_property_read_u16(node, "ti,x-max", &pdata->x_max);
	of_property_read_u16(node, "ti,y-max", &pdata->y_max);

	/*
	 * touchscreen-max-pressure gets parsed during
	 * touchscreen_parse_properties()
	 */
	of_property_read_u16(node, "ti,pressure-min", &pdata->pressure_min);
	if (!of_property_read_u32(node, "touchscreen-min-pressure", &value))
		pdata->pressure_min = (u16) value;
	of_property_read_u16(node, "ti,pressure-max", &pdata->pressure_max);

	of_property_read_u16(node, "ti,debounce-max", &pdata->debounce_max);
	if (!of_property_read_u32(node, "touchscreen-average-samples", &value))
		pdata->debounce_max = (u16) value;
	of_property_read_u16(node, "ti,debounce-tol", &pdata->debounce_tol);
	of_property_read_u16(node, "ti,debounce-rep", &pdata->debounce_rep);

	of_property_read_u32(node, "ti,pendown-gpio-debounce",
			     &pdata->gpio_pendown_debounce);

	pdata->wakeup = of_property_read_bool(node, "wakeup-source") ||
			of_property_read_bool(node, "linux,wakeup");

	pdata->gpio_pendown = of_get_named_gpio(dev->of_node, "pendown-gpio", 0);

	return pdata;
}
#else
static const struct ads7846_platform_data *ads7846_probe_dt(struct device *dev)
{
	dev_err(dev, "no platform data defined\n");
	return ERR_PTR(-EINVAL);
}
#endif

static int ads7846_probe(struct spi_device *spi)
{
	const struct ads7846_platform_data *pdata;
	struct ads7846 *ts;
	struct ads7846_packet *packet;
	struct input_dev *input_dev;
	unsigned long irq_flags;
	int err;

	if (!spi->irq) {
		dev_dbg(&spi->dev, "no IRQ?\n");
		return -EINVAL;
	}

	/* don't exceed max specified sample rate */
	if (spi->max_speed_hz > (125000 * SAMPLE_BITS)) {
		dev_err(&spi->dev, "f(sample) %d KHz?\n",
				(spi->max_speed_hz/SAMPLE_BITS)/1000);
		return -EINVAL;
	}

	/*
	 * We'd set TX word size 8 bits and RX word size to 13 bits ... except
	 * that even if the hardware can do that, the SPI controller driver
	 * may not.  So we stick to very-portable 8 bit words, both RX and TX.
	 */
	spi->bits_per_word = 8;
	spi->mode = SPI_MODE_0;
	err = spi_setup(spi);
	if (err < 0)
		return err;

	ts = kzalloc(sizeof(struct ads7846), GFP_KERNEL);
	packet = kzalloc(sizeof(struct ads7846_packet), GFP_KERNEL);
	input_dev = input_allocate_device();
	if (!ts || !packet || !input_dev) {
		err = -ENOMEM;
		goto err_free_mem;
	}

	spi_set_drvdata(spi, ts);

	ts->packet = packet;
	ts->spi = spi;
	ts->input = input_dev;

	mutex_init(&ts->lock);
	init_waitqueue_head(&ts->wait);

	pdata = dev_get_platdata(&spi->dev);
	if (!pdata) {
		pdata = ads7846_probe_dt(&spi->dev);
		if (IS_ERR(pdata)) {
			err = PTR_ERR(pdata);
			goto err_free_mem;
		}
	}

	ts->model = pdata->model ? : 7846;
	ts->vref_delay_usecs = pdata->vref_delay_usecs ? : 100;
	ts->x_plate_ohms = pdata->x_plate_ohms ? : 400;
	ts->vref_mv = pdata->vref_mv;

	if (pdata->filter != NULL) {
		if (pdata->filter_init != NULL) {
			err = pdata->filter_init(pdata, &ts->filter_data);
			if (err < 0)
				goto err_free_mem;
		}
		ts->filter = pdata->filter;
		ts->filter_cleanup = pdata->filter_cleanup;
	} else if (pdata->debounce_max) {
		ts->debounce_max = pdata->debounce_max;
		if (ts->debounce_max < 2)
			ts->debounce_max = 2;
		ts->debounce_tol = pdata->debounce_tol;
		ts->debounce_rep = pdata->debounce_rep;
		ts->filter = ads7846_debounce_filter;
		ts->filter_data = ts;
	} else {
		ts->filter = ads7846_no_filter;
	}

	err = ads7846_setup_pendown(spi, ts, pdata);
	if (err)
		goto err_cleanup_filter;

	if (pdata->penirq_recheck_delay_usecs)
		ts->penirq_recheck_delay_usecs =
				pdata->penirq_recheck_delay_usecs;

	ts->wait_for_sync = pdata->wait_for_sync ? : null_wait_for_sync;

	snprintf(ts->phys, sizeof(ts->phys), "%s/input0", dev_name(&spi->dev));
	snprintf(ts->name, sizeof(ts->name), "ADS%d Touchscreen", ts->model);

	input_dev->name = ts->name;
	input_dev->phys = ts->phys;
	input_dev->dev.parent = &spi->dev;

	input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
	input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
	input_set_abs_params(input_dev, ABS_X,
			pdata->x_min ? : 0,
			pdata->x_max ? : MAX_12BIT,
			0, 0);
	input_set_abs_params(input_dev, ABS_Y,
			pdata->y_min ? : 0,
			pdata->y_max ? : MAX_12BIT,
			0, 0);
	if (ts->model != 7845)
		input_set_abs_params(input_dev, ABS_PRESSURE,
				pdata->pressure_min, pdata->pressure_max, 0, 0);

	/*
	 * Parse common framework properties. Must be done here to ensure the
	 * correct behaviour in case of using the legacy vendor bindings. The
	 * general binding value overrides the vendor specific one.
	 */
	touchscreen_parse_properties(ts->input, false, &ts->core_prop);
	ts->pressure_max = input_abs_get_max(input_dev, ABS_PRESSURE) ? : ~0;

	/*
	 * Check if legacy ti,swap-xy binding is used instead of
	 * touchscreen-swapped-x-y
	 */
	if (!ts->core_prop.swap_x_y && pdata->swap_xy) {
		swap(input_dev->absinfo[ABS_X], input_dev->absinfo[ABS_Y]);
		ts->core_prop.swap_x_y = true;
	}

	ads7846_setup_spi_msg(ts, pdata);

	ts->reg = regulator_get(&spi->dev, "vcc");
	if (IS_ERR(ts->reg)) {
		err = PTR_ERR(ts->reg);
		dev_err(&spi->dev, "unable to get regulator: %d\n", err);
		goto err_free_gpio;
	}

	err = regulator_enable(ts->reg);
	if (err) {
		dev_err(&spi->dev, "unable to enable regulator: %d\n", err);
		goto err_put_regulator;
	}

	irq_flags = pdata->irq_flags ? : IRQF_TRIGGER_FALLING;
	irq_flags |= IRQF_ONESHOT;

	err = request_threaded_irq(spi->irq, ads7846_hard_irq, ads7846_irq,
				   irq_flags, spi->dev.driver->name, ts);
	if (err && !pdata->irq_flags) {
		dev_info(&spi->dev,
			"trying pin change workaround on irq %d\n", spi->irq);
		irq_flags |= IRQF_TRIGGER_RISING;
		err = request_threaded_irq(spi->irq,
				  ads7846_hard_irq, ads7846_irq,
				  irq_flags, spi->dev.driver->name, ts);
	}

	if (err) {
		dev_dbg(&spi->dev, "irq %d busy?\n", spi->irq);
		goto err_disable_regulator;
	}

	err = ads784x_hwmon_register(spi, ts);
	if (err)
		goto err_free_irq;

	dev_info(&spi->dev, "touchscreen, irq %d\n", spi->irq);

	/*
	 * Take a first sample, leaving nPENIRQ active and vREF off; avoid
	 * the touchscreen, in case it's not connected.
	 */
	if (ts->model == 7845)
		ads7845_read12_ser(&spi->dev, PWRDOWN);
	else
		(void) ads7846_read12_ser(&spi->dev, READ_12BIT_SER(vaux));

	err = sysfs_create_group(&spi->dev.kobj, &ads784x_attr_group);
	if (err)
		goto err_remove_hwmon;

	err = input_register_device(input_dev);
	if (err)
		goto err_remove_attr_group;

	device_init_wakeup(&spi->dev, pdata->wakeup);

	/*
	 * If device does not carry platform data we must have allocated it
	 * when parsing DT data.
	 */
	if (!dev_get_platdata(&spi->dev))
		devm_kfree(&spi->dev, (void *)pdata);

	return 0;

 err_remove_attr_group:
	sysfs_remove_group(&spi->dev.kobj, &ads784x_attr_group);
 err_remove_hwmon:
	ads784x_hwmon_unregister(spi, ts);
 err_free_irq:
	free_irq(spi->irq, ts);
 err_disable_regulator:
	regulator_disable(ts->reg);
 err_put_regulator:
	regulator_put(ts->reg);
 err_free_gpio:
	if (!ts->get_pendown_state)
		gpio_free(ts->gpio_pendown);
 err_cleanup_filter:
	if (ts->filter_cleanup)
		ts->filter_cleanup(ts->filter_data);
 err_free_mem:
	input_free_device(input_dev);
	kfree(packet);
	kfree(ts);
	return err;
}

static int ads7846_remove(struct spi_device *spi)
{
	struct ads7846 *ts = spi_get_drvdata(spi);

	sysfs_remove_group(&spi->dev.kobj, &ads784x_attr_group);

	ads7846_disable(ts);
	free_irq(ts->spi->irq, ts);

	input_unregister_device(ts->input);

	ads784x_hwmon_unregister(spi, ts);

	regulator_put(ts->reg);

	if (!ts->get_pendown_state) {
		/*
		 * If we are not using specialized pendown method we must
		 * have been relying on gpio we set up ourselves.
		 */
		gpio_free(ts->gpio_pendown);
	}

	if (ts->filter_cleanup)
		ts->filter_cleanup(ts->filter_data);

	kfree(ts->packet);
	kfree(ts);

	dev_dbg(&spi->dev, "unregistered touchscreen\n");

	return 0;
}

static struct spi_driver ads7846_driver = {
	.driver = {
		.name	= "ads7846",
		.pm	= &ads7846_pm,
		.of_match_table = of_match_ptr(ads7846_dt_ids),
	},
	.probe		= ads7846_probe,
	.remove		= ads7846_remove,
};

module_spi_driver(ads7846_driver);

MODULE_DESCRIPTION("ADS7846 TouchScreen Driver");
MODULE_LICENSE("GPL");
MODULE_ALIAS("spi:ads7846");