1// SPDX-License-Identifier: GPL-2.0-or-later 2 3/* drivers/atm/firestream.c - FireStream 155 (MB86697) and 4 * FireStream 50 (MB86695) device driver 5 */ 6 7/* Written & (C) 2000 by R.E.Wolff@BitWizard.nl 8 * Copied snippets from zatm.c by Werner Almesberger, EPFL LRC/ICA 9 * and ambassador.c Copyright (C) 1995-1999 Madge Networks Ltd 10 */ 11 12/* 13*/ 14 15 16#include <linux/module.h> 17#include <linux/sched.h> 18#include <linux/kernel.h> 19#include <linux/mm.h> 20#include <linux/pci.h> 21#include <linux/poison.h> 22#include <linux/errno.h> 23#include <linux/atm.h> 24#include <linux/atmdev.h> 25#include <linux/sonet.h> 26#include <linux/skbuff.h> 27#include <linux/netdevice.h> 28#include <linux/delay.h> 29#include <linux/ioport.h> /* for request_region */ 30#include <linux/uio.h> 31#include <linux/init.h> 32#include <linux/interrupt.h> 33#include <linux/capability.h> 34#include <linux/bitops.h> 35#include <linux/slab.h> 36#include <asm/byteorder.h> 37#include <asm/string.h> 38#include <asm/io.h> 39#include <linux/atomic.h> 40#include <linux/uaccess.h> 41#include <linux/wait.h> 42 43#include "firestream.h" 44 45static int loopback = 0; 46static int num=0x5a; 47 48/* According to measurements (but they look suspicious to me!) done in 49 * '97, 37% of the packets are one cell in size. So it pays to have 50 * buffers allocated at that size. A large jump in percentage of 51 * packets occurs at packets around 536 bytes in length. So it also 52 * pays to have those pre-allocated. Unfortunately, we can't fully 53 * take advantage of this as the majority of the packets is likely to 54 * be TCP/IP (As where obviously the measurement comes from) There the 55 * link would be opened with say a 1500 byte MTU, and we can't handle 56 * smaller buffers more efficiently than the larger ones. -- REW 57 */ 58 59/* Due to the way Linux memory management works, specifying "576" as 60 * an allocation size here isn't going to help. They are allocated 61 * from 1024-byte regions anyway. With the size of the sk_buffs (quite 62 * large), it doesn't pay to allocate the smallest size (64) -- REW */ 63 64/* This is all guesswork. Hard numbers to back this up or disprove this, 65 * are appreciated. -- REW */ 66 67/* The last entry should be about 64k. However, the "buffer size" is 68 * passed to the chip in a 16 bit field. I don't know how "65536" 69 * would be interpreted. -- REW */ 70 71#define NP FS_NR_FREE_POOLS 72static int rx_buf_sizes[NP] = {128, 256, 512, 1024, 2048, 4096, 16384, 65520}; 73/* log2: 7 8 9 10 11 12 14 16 */ 74 75#if 0 76static int rx_pool_sizes[NP] = {1024, 1024, 512, 256, 128, 64, 32, 32}; 77#else 78/* debug */ 79static int rx_pool_sizes[NP] = {128, 128, 128, 64, 64, 64, 32, 32}; 80#endif 81/* log2: 10 10 9 8 7 6 5 5 */ 82/* sumlog2: 17 18 18 18 18 18 19 21 */ 83/* mem allocated: 128k 256k 256k 256k 256k 256k 512k 2M */ 84/* tot mem: almost 4M */ 85 86/* NP is shorter, so that it fits on a single line. */ 87#undef NP 88 89 90/* Small hardware gotcha: 91 92 The FS50 CAM (VP/VC match registers) always take the lowest channel 93 number that matches. This is not a problem. 94 95 However, they also ignore whether the channel is enabled or 96 not. This means that if you allocate channel 0 to 1.2 and then 97 channel 1 to 0.0, then disabeling channel 0 and writing 0 to the 98 match channel for channel 0 will "steal" the traffic from channel 99 1, even if you correctly disable channel 0. 100 101 Workaround: 102 103 - When disabling channels, write an invalid VP/VC value to the 104 match register. (We use 0xffffffff, which in the worst case 105 matches VP/VC = <maxVP>/<maxVC>, but I expect it not to match 106 anything as some "when not in use, program to 0" bits are now 107 programmed to 1...) 108 109 - Don't initialize the match registers to 0, as 0.0 is a valid 110 channel. 111*/ 112 113 114/* Optimization hints and tips. 115 116 The FireStream chips are very capable of reducing the amount of 117 "interrupt-traffic" for the CPU. This driver requests an interrupt on EVERY 118 action. You could try to minimize this a bit. 119 120 Besides that, the userspace->kernel copy and the PCI bus are the 121 performance limiting issues for this driver. 122 123 You could queue up a bunch of outgoing packets without telling the 124 FireStream. I'm not sure that's going to win you much though. The 125 Linux layer won't tell us in advance when it's not going to give us 126 any more packets in a while. So this is tricky to implement right without 127 introducing extra delays. 128 129 -- REW 130 */ 131 132 133 134 135/* The strings that define what the RX queue entry is all about. */ 136/* Fujitsu: Please tell me which ones can have a pointer to a 137 freepool descriptor! */ 138static char *res_strings[] = { 139 "RX OK: streaming not EOP", 140 "RX OK: streaming EOP", 141 "RX OK: Single buffer packet", 142 "RX OK: packet mode", 143 "RX OK: F4 OAM (end to end)", 144 "RX OK: F4 OAM (Segment)", 145 "RX OK: F5 OAM (end to end)", 146 "RX OK: F5 OAM (Segment)", 147 "RX OK: RM cell", 148 "RX OK: TRANSP cell", 149 "RX OK: TRANSPC cell", 150 "Unmatched cell", 151 "reserved 12", 152 "reserved 13", 153 "reserved 14", 154 "Unrecognized cell", 155 "reserved 16", 156 "reassembly abort: AAL5 abort", 157 "packet purged", 158 "packet ageing timeout", 159 "channel ageing timeout", 160 "calculated length error", 161 "programmed length limit error", 162 "aal5 crc32 error", 163 "oam transp or transpc crc10 error", 164 "reserved 25", 165 "reserved 26", 166 "reserved 27", 167 "reserved 28", 168 "reserved 29", 169 "reserved 30", /* FIXME: The strings between 30-40 might be wrong. */ 170 "reassembly abort: no buffers", 171 "receive buffer overflow", 172 "change in GFC", 173 "receive buffer full", 174 "low priority discard - no receive descriptor", 175 "low priority discard - missing end of packet", 176 "reserved 37", 177 "reserved 38", 178 "reserved 39", 179 "reserved 40", 180 "reserved 41", 181 "reserved 42", 182 "reserved 43", 183 "reserved 44", 184 "reserved 45", 185 "reserved 46", 186 "reserved 47", 187 "reserved 48", 188 "reserved 49", 189 "reserved 50", 190 "reserved 51", 191 "reserved 52", 192 "reserved 53", 193 "reserved 54", 194 "reserved 55", 195 "reserved 56", 196 "reserved 57", 197 "reserved 58", 198 "reserved 59", 199 "reserved 60", 200 "reserved 61", 201 "reserved 62", 202 "reserved 63", 203}; 204 205static char *irq_bitname[] = { 206 "LPCO", 207 "DPCO", 208 "RBRQ0_W", 209 "RBRQ1_W", 210 "RBRQ2_W", 211 "RBRQ3_W", 212 "RBRQ0_NF", 213 "RBRQ1_NF", 214 "RBRQ2_NF", 215 "RBRQ3_NF", 216 "BFP_SC", 217 "INIT", 218 "INIT_ERR", 219 "USCEO", 220 "UPEC0", 221 "VPFCO", 222 "CRCCO", 223 "HECO", 224 "TBRQ_W", 225 "TBRQ_NF", 226 "CTPQ_E", 227 "GFC_C0", 228 "PCI_FTL", 229 "CSQ_W", 230 "CSQ_NF", 231 "EXT_INT", 232 "RXDMA_S" 233}; 234 235 236#define PHY_EOF -1 237#define PHY_CLEARALL -2 238 239struct reginit_item { 240 int reg, val; 241}; 242 243 244static struct reginit_item PHY_NTC_INIT[] = { 245 { PHY_CLEARALL, 0x40 }, 246 { 0x12, 0x0001 }, 247 { 0x13, 0x7605 }, 248 { 0x1A, 0x0001 }, 249 { 0x1B, 0x0005 }, 250 { 0x38, 0x0003 }, 251 { 0x39, 0x0006 }, /* changed here to make loopback */ 252 { 0x01, 0x5262 }, 253 { 0x15, 0x0213 }, 254 { 0x00, 0x0003 }, 255 { PHY_EOF, 0}, /* -1 signals end of list */ 256}; 257 258 259/* Safetyfeature: If the card interrupts more than this number of times 260 in a jiffy (1/100th of a second) then we just disable the interrupt and 261 print a message. This prevents the system from hanging. 262 263 150000 packets per second is close to the limit a PC is going to have 264 anyway. We therefore have to disable this for production. -- REW */ 265#undef IRQ_RATE_LIMIT // 100 266 267/* Interrupts work now. Unlike serial cards, ATM cards don't work all 268 that great without interrupts. -- REW */ 269#undef FS_POLL_FREQ // 100 270 271/* 272 This driver can spew a whole lot of debugging output at you. If you 273 need maximum performance, you should disable the DEBUG define. To 274 aid in debugging in the field, I'm leaving the compile-time debug 275 features enabled, and disable them "runtime". That allows me to 276 instruct people with problems to enable debugging without requiring 277 them to recompile... -- REW 278*/ 279#define DEBUG 280 281#ifdef DEBUG 282#define fs_dprintk(f, str...) if (fs_debug & f) printk (str) 283#else 284#define fs_dprintk(f, str...) /* nothing */ 285#endif 286 287 288static int fs_keystream = 0; 289 290#ifdef DEBUG 291/* I didn't forget to set this to zero before shipping. Hit me with a stick 292 if you get this with the debug default not set to zero again. -- REW */ 293static int fs_debug = 0; 294#else 295#define fs_debug 0 296#endif 297 298#ifdef MODULE 299#ifdef DEBUG 300module_param(fs_debug, int, 0644); 301#endif 302module_param(loopback, int, 0); 303module_param(num, int, 0); 304module_param(fs_keystream, int, 0); 305/* XXX Add rx_buf_sizes, and rx_pool_sizes As per request Amar. -- REW */ 306#endif 307 308 309#define FS_DEBUG_FLOW 0x00000001 310#define FS_DEBUG_OPEN 0x00000002 311#define FS_DEBUG_QUEUE 0x00000004 312#define FS_DEBUG_IRQ 0x00000008 313#define FS_DEBUG_INIT 0x00000010 314#define FS_DEBUG_SEND 0x00000020 315#define FS_DEBUG_PHY 0x00000040 316#define FS_DEBUG_CLEANUP 0x00000080 317#define FS_DEBUG_QOS 0x00000100 318#define FS_DEBUG_TXQ 0x00000200 319#define FS_DEBUG_ALLOC 0x00000400 320#define FS_DEBUG_TXMEM 0x00000800 321#define FS_DEBUG_QSIZE 0x00001000 322 323 324#define func_enter() fs_dprintk(FS_DEBUG_FLOW, "fs: enter %s\n", __func__) 325#define func_exit() fs_dprintk(FS_DEBUG_FLOW, "fs: exit %s\n", __func__) 326 327 328static struct fs_dev *fs_boards = NULL; 329 330#ifdef DEBUG 331 332static void my_hd (void *addr, int len) 333{ 334 int j, ch; 335 unsigned char *ptr = addr; 336 337 while (len > 0) { 338 printk ("%p ", ptr); 339 for (j=0;j < ((len < 16)?len:16);j++) { 340 printk ("%02x %s", ptr[j], (j==7)?" ":""); 341 } 342 for ( ;j < 16;j++) { 343 printk (" %s", (j==7)?" ":""); 344 } 345 for (j=0;j < ((len < 16)?len:16);j++) { 346 ch = ptr[j]; 347 printk ("%c", (ch < 0x20)?'.':((ch > 0x7f)?'.':ch)); 348 } 349 printk ("\n"); 350 ptr += 16; 351 len -= 16; 352 } 353} 354#else /* DEBUG */ 355static void my_hd (void *addr, int len){} 356#endif /* DEBUG */ 357 358/********** free an skb (as per ATM device driver documentation) **********/ 359 360/* Hmm. If this is ATM specific, why isn't there an ATM routine for this? 361 * I copied it over from the ambassador driver. -- REW */ 362 363static inline void fs_kfree_skb (struct sk_buff * skb) 364{ 365 if (ATM_SKB(skb)->vcc->pop) 366 ATM_SKB(skb)->vcc->pop (ATM_SKB(skb)->vcc, skb); 367 else 368 dev_kfree_skb_any (skb); 369} 370 371 372 373 374/* It seems the ATM forum recommends this horribly complicated 16bit 375 * floating point format. Turns out the Ambassador uses the exact same 376 * encoding. I just copied it over. If Mitch agrees, I'll move it over 377 * to the atm_misc file or something like that. (and remove it from 378 * here and the ambassador driver) -- REW 379 */ 380 381/* The good thing about this format is that it is monotonic. So, 382 a conversion routine need not be very complicated. To be able to 383 round "nearest" we need to take along a few extra bits. Lets 384 put these after 16 bits, so that we can just return the top 16 385 bits of the 32bit number as the result: 386 387 int mr (unsigned int rate, int r) 388 { 389 int e = 16+9; 390 static int round[4]={0, 0, 0xffff, 0x8000}; 391 if (!rate) return 0; 392 while (rate & 0xfc000000) { 393 rate >>= 1; 394 e++; 395 } 396 while (! (rate & 0xfe000000)) { 397 rate <<= 1; 398 e--; 399 } 400 401// Now the mantissa is in positions bit 16-25. Excepf for the "hidden 1" that's in bit 26. 402 rate &= ~0x02000000; 403// Next add in the exponent 404 rate |= e << (16+9); 405// And perform the rounding: 406 return (rate + round[r]) >> 16; 407 } 408 409 14 lines-of-code. Compare that with the 120 that the Ambassador 410 guys needed. (would be 8 lines shorter if I'd try to really reduce 411 the number of lines: 412 413 int mr (unsigned int rate, int r) 414 { 415 int e = 16+9; 416 static int round[4]={0, 0, 0xffff, 0x8000}; 417 if (!rate) return 0; 418 for (; rate & 0xfc000000 ;rate >>= 1, e++); 419 for (;!(rate & 0xfe000000);rate <<= 1, e--); 420 return ((rate & ~0x02000000) | (e << (16+9)) + round[r]) >> 16; 421 } 422 423 Exercise for the reader: Remove one more line-of-code, without 424 cheating. (Just joining two lines is cheating). (I know it's 425 possible, don't think you've beat me if you found it... If you 426 manage to lose two lines or more, keep me updated! ;-) 427 428 -- REW */ 429 430 431#define ROUND_UP 1 432#define ROUND_DOWN 2 433#define ROUND_NEAREST 3 434/********** make rate (not quite as much fun as Horizon) **********/ 435 436static int make_rate(unsigned int rate, int r, 437 u16 *bits, unsigned int *actual) 438{ 439 unsigned char exp = -1; /* hush gcc */ 440 unsigned int man = -1; /* hush gcc */ 441 442 fs_dprintk (FS_DEBUG_QOS, "make_rate %u", rate); 443 444 /* rates in cells per second, ITU format (nasty 16-bit floating-point) 445 given 5-bit e and 9-bit m: 446 rate = EITHER (1+m/2^9)*2^e OR 0 447 bits = EITHER 1<<14 | e<<9 | m OR 0 448 (bit 15 is "reserved", bit 14 "non-zero") 449 smallest rate is 0 (special representation) 450 largest rate is (1+511/512)*2^31 = 4290772992 (< 2^32-1) 451 smallest non-zero rate is (1+0/512)*2^0 = 1 (> 0) 452 simple algorithm: 453 find position of top bit, this gives e 454 remove top bit and shift (rounding if feeling clever) by 9-e 455 */ 456 /* Ambassador ucode bug: please don't set bit 14! so 0 rate not 457 representable. // This should move into the ambassador driver 458 when properly merged. -- REW */ 459 460 if (rate > 0xffc00000U) { 461 /* larger than largest representable rate */ 462 463 if (r == ROUND_UP) { 464 return -EINVAL; 465 } else { 466 exp = 31; 467 man = 511; 468 } 469 470 } else if (rate) { 471 /* representable rate */ 472 473 exp = 31; 474 man = rate; 475 476 /* invariant: rate = man*2^(exp-31) */ 477 while (!(man & (1<<31))) { 478 exp = exp - 1; 479 man = man<<1; 480 } 481 482 /* man has top bit set 483 rate = (2^31+(man-2^31))*2^(exp-31) 484 rate = (1+(man-2^31)/2^31)*2^exp 485 */ 486 man = man<<1; 487 man &= 0xffffffffU; /* a nop on 32-bit systems */ 488 /* rate = (1+man/2^32)*2^exp 489 490 exp is in the range 0 to 31, man is in the range 0 to 2^32-1 491 time to lose significance... we want m in the range 0 to 2^9-1 492 rounding presents a minor problem... we first decide which way 493 we are rounding (based on given rounding direction and possibly 494 the bits of the mantissa that are to be discarded). 495 */ 496 497 switch (r) { 498 case ROUND_DOWN: { 499 /* just truncate */ 500 man = man>>(32-9); 501 break; 502 } 503 case ROUND_UP: { 504 /* check all bits that we are discarding */ 505 if (man & (~0U>>9)) { 506 man = (man>>(32-9)) + 1; 507 if (man == (1<<9)) { 508 /* no need to check for round up outside of range */ 509 man = 0; 510 exp += 1; 511 } 512 } else { 513 man = (man>>(32-9)); 514 } 515 break; 516 } 517 case ROUND_NEAREST: { 518 /* check msb that we are discarding */ 519 if (man & (1<<(32-9-1))) { 520 man = (man>>(32-9)) + 1; 521 if (man == (1<<9)) { 522 /* no need to check for round up outside of range */ 523 man = 0; 524 exp += 1; 525 } 526 } else { 527 man = (man>>(32-9)); 528 } 529 break; 530 } 531 } 532 533 } else { 534 /* zero rate - not representable */ 535 536 if (r == ROUND_DOWN) { 537 return -EINVAL; 538 } else { 539 exp = 0; 540 man = 0; 541 } 542 } 543 544 fs_dprintk (FS_DEBUG_QOS, "rate: man=%u, exp=%hu", man, exp); 545 546 if (bits) 547 *bits = /* (1<<14) | */ (exp<<9) | man; 548 549 if (actual) 550 *actual = (exp >= 9) 551 ? (1 << exp) + (man << (exp-9)) 552 : (1 << exp) + ((man + (1<<(9-exp-1))) >> (9-exp)); 553 554 return 0; 555} 556 557 558 559 560/* FireStream access routines */ 561/* For DEEP-DOWN debugging these can be rigged to intercept accesses to 562 certain registers or to just log all accesses. */ 563 564static inline void write_fs (struct fs_dev *dev, int offset, u32 val) 565{ 566 writel (val, dev->base + offset); 567} 568 569 570static inline u32 read_fs (struct fs_dev *dev, int offset) 571{ 572 return readl (dev->base + offset); 573} 574 575 576 577static inline struct FS_QENTRY *get_qentry (struct fs_dev *dev, struct queue *q) 578{ 579 return bus_to_virt (read_fs (dev, Q_WP(q->offset)) & Q_ADDR_MASK); 580} 581 582 583static void submit_qentry (struct fs_dev *dev, struct queue *q, struct FS_QENTRY *qe) 584{ 585 u32 wp; 586 struct FS_QENTRY *cqe; 587 588 /* XXX Sanity check: the write pointer can be checked to be 589 still the same as the value passed as qe... -- REW */ 590 /* udelay (5); */ 591 while ((wp = read_fs (dev, Q_WP (q->offset))) & Q_FULL) { 592 fs_dprintk (FS_DEBUG_TXQ, "Found queue at %x full. Waiting.\n", 593 q->offset); 594 schedule (); 595 } 596 597 wp &= ~0xf; 598 cqe = bus_to_virt (wp); 599 if (qe != cqe) { 600 fs_dprintk (FS_DEBUG_TXQ, "q mismatch! %p %p\n", qe, cqe); 601 } 602 603 write_fs (dev, Q_WP(q->offset), Q_INCWRAP); 604 605 { 606 static int c; 607 if (!(c++ % 100)) 608 { 609 int rp, wp; 610 rp = read_fs (dev, Q_RP(q->offset)); 611 wp = read_fs (dev, Q_WP(q->offset)); 612 fs_dprintk (FS_DEBUG_TXQ, "q at %d: %x-%x: %x entries.\n", 613 q->offset, rp, wp, wp-rp); 614 } 615 } 616} 617 618#ifdef DEBUG_EXTRA 619static struct FS_QENTRY pq[60]; 620static int qp; 621 622static struct FS_BPENTRY dq[60]; 623static int qd; 624static void *da[60]; 625#endif 626 627static void submit_queue (struct fs_dev *dev, struct queue *q, 628 u32 cmd, u32 p1, u32 p2, u32 p3) 629{ 630 struct FS_QENTRY *qe; 631 632 qe = get_qentry (dev, q); 633 qe->cmd = cmd; 634 qe->p0 = p1; 635 qe->p1 = p2; 636 qe->p2 = p3; 637 submit_qentry (dev, q, qe); 638 639#ifdef DEBUG_EXTRA 640 pq[qp].cmd = cmd; 641 pq[qp].p0 = p1; 642 pq[qp].p1 = p2; 643 pq[qp].p2 = p3; 644 qp++; 645 if (qp >= 60) qp = 0; 646#endif 647} 648 649/* Test the "other" way one day... -- REW */ 650#if 1 651#define submit_command submit_queue 652#else 653 654static void submit_command (struct fs_dev *dev, struct queue *q, 655 u32 cmd, u32 p1, u32 p2, u32 p3) 656{ 657 write_fs (dev, CMDR0, cmd); 658 write_fs (dev, CMDR1, p1); 659 write_fs (dev, CMDR2, p2); 660 write_fs (dev, CMDR3, p3); 661} 662#endif 663 664 665 666static void process_return_queue (struct fs_dev *dev, struct queue *q) 667{ 668 long rq; 669 struct FS_QENTRY *qe; 670 void *tc; 671 672 while (!((rq = read_fs (dev, Q_RP(q->offset))) & Q_EMPTY)) { 673 fs_dprintk (FS_DEBUG_QUEUE, "reaping return queue entry at %lx\n", rq); 674 qe = bus_to_virt (rq); 675 676 fs_dprintk (FS_DEBUG_QUEUE, "queue entry: %08x %08x %08x %08x. (%d)\n", 677 qe->cmd, qe->p0, qe->p1, qe->p2, STATUS_CODE (qe)); 678 679 switch (STATUS_CODE (qe)) { 680 case 5: 681 tc = bus_to_virt (qe->p0); 682 fs_dprintk (FS_DEBUG_ALLOC, "Free tc: %p\n", tc); 683 kfree (tc); 684 break; 685 } 686 687 write_fs (dev, Q_RP(q->offset), Q_INCWRAP); 688 } 689} 690 691 692static void process_txdone_queue (struct fs_dev *dev, struct queue *q) 693{ 694 long rq; 695 long tmp; 696 struct FS_QENTRY *qe; 697 struct sk_buff *skb; 698 struct FS_BPENTRY *td; 699 700 while (!((rq = read_fs (dev, Q_RP(q->offset))) & Q_EMPTY)) { 701 fs_dprintk (FS_DEBUG_QUEUE, "reaping txdone entry at %lx\n", rq); 702 qe = bus_to_virt (rq); 703 704 fs_dprintk (FS_DEBUG_QUEUE, "queue entry: %08x %08x %08x %08x: %d\n", 705 qe->cmd, qe->p0, qe->p1, qe->p2, STATUS_CODE (qe)); 706 707 if (STATUS_CODE (qe) != 2) 708 fs_dprintk (FS_DEBUG_TXMEM, "queue entry: %08x %08x %08x %08x: %d\n", 709 qe->cmd, qe->p0, qe->p1, qe->p2, STATUS_CODE (qe)); 710 711 712 switch (STATUS_CODE (qe)) { 713 case 0x01: /* This is for AAL0 where we put the chip in streaming mode */ 714 fallthrough; 715 case 0x02: 716 /* Process a real txdone entry. */ 717 tmp = qe->p0; 718 if (tmp & 0x0f) 719 printk (KERN_WARNING "td not aligned: %ld\n", tmp); 720 tmp &= ~0x0f; 721 td = bus_to_virt (tmp); 722 723 fs_dprintk (FS_DEBUG_QUEUE, "Pool entry: %08x %08x %08x %08x %p.\n", 724 td->flags, td->next, td->bsa, td->aal_bufsize, td->skb ); 725 726 skb = td->skb; 727 if (skb == FS_VCC (ATM_SKB(skb)->vcc)->last_skb) { 728 FS_VCC (ATM_SKB(skb)->vcc)->last_skb = NULL; 729 wake_up_interruptible (& FS_VCC (ATM_SKB(skb)->vcc)->close_wait); 730 } 731 td->dev->ntxpckts--; 732 733 { 734 static int c=0; 735 736 if (!(c++ % 100)) { 737 fs_dprintk (FS_DEBUG_QSIZE, "[%d]", td->dev->ntxpckts); 738 } 739 } 740 741 atomic_inc(&ATM_SKB(skb)->vcc->stats->tx); 742 743 fs_dprintk (FS_DEBUG_TXMEM, "i"); 744 fs_dprintk (FS_DEBUG_ALLOC, "Free t-skb: %p\n", skb); 745 fs_kfree_skb (skb); 746 747 fs_dprintk (FS_DEBUG_ALLOC, "Free trans-d: %p\n", td); 748 memset (td, ATM_POISON_FREE, sizeof(struct FS_BPENTRY)); 749 kfree (td); 750 break; 751 default: 752 /* Here we get the tx purge inhibit command ... */ 753 /* Action, I believe, is "don't do anything". -- REW */ 754 ; 755 } 756 757 write_fs (dev, Q_RP(q->offset), Q_INCWRAP); 758 } 759} 760 761 762static void process_incoming (struct fs_dev *dev, struct queue *q) 763{ 764 long rq; 765 struct FS_QENTRY *qe; 766 struct FS_BPENTRY *pe; 767 struct sk_buff *skb; 768 unsigned int channo; 769 struct atm_vcc *atm_vcc; 770 771 while (!((rq = read_fs (dev, Q_RP(q->offset))) & Q_EMPTY)) { 772 fs_dprintk (FS_DEBUG_QUEUE, "reaping incoming queue entry at %lx\n", rq); 773 qe = bus_to_virt (rq); 774 775 fs_dprintk (FS_DEBUG_QUEUE, "queue entry: %08x %08x %08x %08x. ", 776 qe->cmd, qe->p0, qe->p1, qe->p2); 777 778 fs_dprintk (FS_DEBUG_QUEUE, "-> %x: %s\n", 779 STATUS_CODE (qe), 780 res_strings[STATUS_CODE(qe)]); 781 782 pe = bus_to_virt (qe->p0); 783 fs_dprintk (FS_DEBUG_QUEUE, "Pool entry: %08x %08x %08x %08x %p %p.\n", 784 pe->flags, pe->next, pe->bsa, pe->aal_bufsize, 785 pe->skb, pe->fp); 786 787 channo = qe->cmd & 0xffff; 788 789 if (channo < dev->nchannels) 790 atm_vcc = dev->atm_vccs[channo]; 791 else 792 atm_vcc = NULL; 793 794 /* Single buffer packet */ 795 switch (STATUS_CODE (qe)) { 796 case 0x1: 797 /* Fall through for streaming mode */ 798 case 0x2:/* Packet received OK.... */ 799 if (atm_vcc) { 800 skb = pe->skb; 801 pe->fp->n--; 802#if 0 803 fs_dprintk (FS_DEBUG_QUEUE, "Got skb: %p\n", skb); 804 if (FS_DEBUG_QUEUE & fs_debug) my_hd (bus_to_virt (pe->bsa), 0x20); 805#endif 806 skb_put (skb, qe->p1 & 0xffff); 807 ATM_SKB(skb)->vcc = atm_vcc; 808 atomic_inc(&atm_vcc->stats->rx); 809 __net_timestamp(skb); 810 fs_dprintk (FS_DEBUG_ALLOC, "Free rec-skb: %p (pushed)\n", skb); 811 atm_vcc->push (atm_vcc, skb); 812 fs_dprintk (FS_DEBUG_ALLOC, "Free rec-d: %p\n", pe); 813 kfree (pe); 814 } else { 815 printk (KERN_ERR "Got a receive on a non-open channel %d.\n", channo); 816 } 817 break; 818 case 0x17:/* AAL 5 CRC32 error. IFF the length field is nonzero, a buffer 819 has been consumed and needs to be processed. -- REW */ 820 if (qe->p1 & 0xffff) { 821 pe = bus_to_virt (qe->p0); 822 pe->fp->n--; 823 fs_dprintk (FS_DEBUG_ALLOC, "Free rec-skb: %p\n", pe->skb); 824 dev_kfree_skb_any (pe->skb); 825 fs_dprintk (FS_DEBUG_ALLOC, "Free rec-d: %p\n", pe); 826 kfree (pe); 827 } 828 if (atm_vcc) 829 atomic_inc(&atm_vcc->stats->rx_drop); 830 break; 831 case 0x1f: /* Reassembly abort: no buffers. */ 832 /* Silently increment error counter. */ 833 if (atm_vcc) 834 atomic_inc(&atm_vcc->stats->rx_drop); 835 break; 836 default: /* Hmm. Haven't written the code to handle the others yet... -- REW */ 837 printk (KERN_WARNING "Don't know what to do with RX status %x: %s.\n", 838 STATUS_CODE(qe), res_strings[STATUS_CODE (qe)]); 839 } 840 write_fs (dev, Q_RP(q->offset), Q_INCWRAP); 841 } 842} 843 844 845 846#define DO_DIRECTION(tp) ((tp)->traffic_class != ATM_NONE) 847 848static int fs_open(struct atm_vcc *atm_vcc) 849{ 850 struct fs_dev *dev; 851 struct fs_vcc *vcc; 852 struct fs_transmit_config *tc; 853 struct atm_trafprm * txtp; 854 struct atm_trafprm * rxtp; 855 /* struct fs_receive_config *rc;*/ 856 /* struct FS_QENTRY *qe; */ 857 int error; 858 int bfp; 859 int to; 860 unsigned short tmc0; 861 short vpi = atm_vcc->vpi; 862 int vci = atm_vcc->vci; 863 864 func_enter (); 865 866 dev = FS_DEV(atm_vcc->dev); 867 fs_dprintk (FS_DEBUG_OPEN, "fs: open on dev: %p, vcc at %p\n", 868 dev, atm_vcc); 869 870 if (vci != ATM_VPI_UNSPEC && vpi != ATM_VCI_UNSPEC) 871 set_bit(ATM_VF_ADDR, &atm_vcc->flags); 872 873 if ((atm_vcc->qos.aal != ATM_AAL5) && 874 (atm_vcc->qos.aal != ATM_AAL2)) 875 return -EINVAL; /* XXX AAL0 */ 876 877 fs_dprintk (FS_DEBUG_OPEN, "fs: (itf %d): open %d.%d\n", 878 atm_vcc->dev->number, atm_vcc->vpi, atm_vcc->vci); 879 880 /* XXX handle qos parameters (rate limiting) ? */ 881 882 vcc = kmalloc(sizeof(struct fs_vcc), GFP_KERNEL); 883 fs_dprintk (FS_DEBUG_ALLOC, "Alloc VCC: %p(%zd)\n", vcc, sizeof(struct fs_vcc)); 884 if (!vcc) { 885 clear_bit(ATM_VF_ADDR, &atm_vcc->flags); 886 return -ENOMEM; 887 } 888 889 atm_vcc->dev_data = vcc; 890 vcc->last_skb = NULL; 891 892 init_waitqueue_head (&vcc->close_wait); 893 894 txtp = &atm_vcc->qos.txtp; 895 rxtp = &atm_vcc->qos.rxtp; 896 897 if (!test_bit(ATM_VF_PARTIAL, &atm_vcc->flags)) { 898 if (IS_FS50(dev)) { 899 /* Increment the channel numer: take a free one next time. */ 900 for (to=33;to;to--, dev->channo++) { 901 /* We only have 32 channels */ 902 if (dev->channo >= 32) 903 dev->channo = 0; 904 /* If we need to do RX, AND the RX is inuse, try the next */ 905 if (DO_DIRECTION(rxtp) && dev->atm_vccs[dev->channo]) 906 continue; 907 /* If we need to do TX, AND the TX is inuse, try the next */ 908 if (DO_DIRECTION(txtp) && test_bit (dev->channo, dev->tx_inuse)) 909 continue; 910 /* Ok, both are free! (or not needed) */ 911 break; 912 } 913 if (!to) { 914 printk ("No more free channels for FS50..\n"); 915 kfree(vcc); 916 return -EBUSY; 917 } 918 vcc->channo = dev->channo; 919 dev->channo &= dev->channel_mask; 920 921 } else { 922 vcc->channo = (vpi << FS155_VCI_BITS) | (vci); 923 if (((DO_DIRECTION(rxtp) && dev->atm_vccs[vcc->channo])) || 924 ( DO_DIRECTION(txtp) && test_bit (vcc->channo, dev->tx_inuse))) { 925 printk ("Channel is in use for FS155.\n"); 926 kfree(vcc); 927 return -EBUSY; 928 } 929 } 930 fs_dprintk (FS_DEBUG_OPEN, "OK. Allocated channel %x(%d).\n", 931 vcc->channo, vcc->channo); 932 } 933 934 if (DO_DIRECTION (txtp)) { 935 tc = kmalloc (sizeof (struct fs_transmit_config), GFP_KERNEL); 936 fs_dprintk (FS_DEBUG_ALLOC, "Alloc tc: %p(%zd)\n", 937 tc, sizeof (struct fs_transmit_config)); 938 if (!tc) { 939 fs_dprintk (FS_DEBUG_OPEN, "fs: can't alloc transmit_config.\n"); 940 kfree(vcc); 941 return -ENOMEM; 942 } 943 944 /* Allocate the "open" entry from the high priority txq. This makes 945 it most likely that the chip will notice it. It also prevents us 946 from having to wait for completion. On the other hand, we may 947 need to wait for completion anyway, to see if it completed 948 successfully. */ 949 950 switch (atm_vcc->qos.aal) { 951 case ATM_AAL2: 952 case ATM_AAL0: 953 tc->flags = 0 954 | TC_FLAGS_TRANSPARENT_PAYLOAD 955 | TC_FLAGS_PACKET 956 | (1 << 28) 957 | TC_FLAGS_TYPE_UBR /* XXX Change to VBR -- PVDL */ 958 | TC_FLAGS_CAL0; 959 break; 960 case ATM_AAL5: 961 tc->flags = 0 962 | TC_FLAGS_AAL5 963 | TC_FLAGS_PACKET /* ??? */ 964 | TC_FLAGS_TYPE_CBR 965 | TC_FLAGS_CAL0; 966 break; 967 default: 968 printk ("Unknown aal: %d\n", atm_vcc->qos.aal); 969 tc->flags = 0; 970 } 971 /* Docs are vague about this atm_hdr field. By the way, the FS 972 * chip makes odd errors if lower bits are set.... -- REW */ 973 tc->atm_hdr = (vpi << 20) | (vci << 4); 974 tmc0 = 0; 975 { 976 int pcr = atm_pcr_goal (txtp); 977 978 fs_dprintk (FS_DEBUG_OPEN, "pcr = %d.\n", pcr); 979 980 /* XXX Hmm. officially we're only allowed to do this if rounding 981 is round_down -- REW */ 982 if (IS_FS50(dev)) { 983 if (pcr > 51840000/53/8) pcr = 51840000/53/8; 984 } else { 985 if (pcr > 155520000/53/8) pcr = 155520000/53/8; 986 } 987 if (!pcr) { 988 /* no rate cap */ 989 tmc0 = IS_FS50(dev)?0x61BE:0x64c9; /* Just copied over the bits from Fujitsu -- REW */ 990 } else { 991 int r; 992 if (pcr < 0) { 993 r = ROUND_DOWN; 994 pcr = -pcr; 995 } else { 996 r = ROUND_UP; 997 } 998 error = make_rate (pcr, r, &tmc0, NULL); 999 if (error) { 1000 kfree(tc); 1001 kfree(vcc); 1002 return error; 1003 } 1004 } 1005 fs_dprintk (FS_DEBUG_OPEN, "pcr = %d.\n", pcr); 1006 } 1007 1008 tc->TMC[0] = tmc0 | 0x4000; 1009 tc->TMC[1] = 0; /* Unused */ 1010 tc->TMC[2] = 0; /* Unused */ 1011 tc->TMC[3] = 0; /* Unused */ 1012 1013 tc->spec = 0; /* UTOPIA address, UDF, HEC: Unused -> 0 */ 1014 tc->rtag[0] = 0; /* What should I do with routing tags??? 1015 -- Not used -- AS -- Thanks -- REW*/ 1016 tc->rtag[1] = 0; 1017 tc->rtag[2] = 0; 1018 1019 if (fs_debug & FS_DEBUG_OPEN) { 1020 fs_dprintk (FS_DEBUG_OPEN, "TX config record:\n"); 1021 my_hd (tc, sizeof (*tc)); 1022 } 1023 1024 /* We now use the "submit_command" function to submit commands to 1025 the firestream. There is a define up near the definition of 1026 that routine that switches this routine between immediate write 1027 to the immediate command registers and queuing the commands in 1028 the HPTXQ for execution. This last technique might be more 1029 efficient if we know we're going to submit a whole lot of 1030 commands in one go, but this driver is not setup to be able to 1031 use such a construct. So it probably doen't matter much right 1032 now. -- REW */ 1033 1034 /* The command is IMMediate and INQueue. The parameters are out-of-line.. */ 1035 submit_command (dev, &dev->hp_txq, 1036 QE_CMD_CONFIG_TX | QE_CMD_IMM_INQ | vcc->channo, 1037 virt_to_bus (tc), 0, 0); 1038 1039 submit_command (dev, &dev->hp_txq, 1040 QE_CMD_TX_EN | QE_CMD_IMM_INQ | vcc->channo, 1041 0, 0, 0); 1042 set_bit (vcc->channo, dev->tx_inuse); 1043 } 1044 1045 if (DO_DIRECTION (rxtp)) { 1046 dev->atm_vccs[vcc->channo] = atm_vcc; 1047 1048 for (bfp = 0;bfp < FS_NR_FREE_POOLS; bfp++) 1049 if (atm_vcc->qos.rxtp.max_sdu <= dev->rx_fp[bfp].bufsize) break; 1050 if (bfp >= FS_NR_FREE_POOLS) { 1051 fs_dprintk (FS_DEBUG_OPEN, "No free pool fits sdu: %d.\n", 1052 atm_vcc->qos.rxtp.max_sdu); 1053 /* XXX Cleanup? -- Would just calling fs_close work??? -- REW */ 1054 1055 /* XXX clear tx inuse. Close TX part? */ 1056 dev->atm_vccs[vcc->channo] = NULL; 1057 kfree (vcc); 1058 return -EINVAL; 1059 } 1060 1061 switch (atm_vcc->qos.aal) { 1062 case ATM_AAL0: 1063 case ATM_AAL2: 1064 submit_command (dev, &dev->hp_txq, 1065 QE_CMD_CONFIG_RX | QE_CMD_IMM_INQ | vcc->channo, 1066 RC_FLAGS_TRANSP | 1067 RC_FLAGS_BFPS_BFP * bfp | 1068 RC_FLAGS_RXBM_PSB, 0, 0); 1069 break; 1070 case ATM_AAL5: 1071 submit_command (dev, &dev->hp_txq, 1072 QE_CMD_CONFIG_RX | QE_CMD_IMM_INQ | vcc->channo, 1073 RC_FLAGS_AAL5 | 1074 RC_FLAGS_BFPS_BFP * bfp | 1075 RC_FLAGS_RXBM_PSB, 0, 0); 1076 break; 1077 } 1078 if (IS_FS50 (dev)) { 1079 submit_command (dev, &dev->hp_txq, 1080 QE_CMD_REG_WR | QE_CMD_IMM_INQ, 1081 0x80 + vcc->channo, 1082 (vpi << 16) | vci, 0 ); /* XXX -- Use defines. */ 1083 } 1084 submit_command (dev, &dev->hp_txq, 1085 QE_CMD_RX_EN | QE_CMD_IMM_INQ | vcc->channo, 1086 0, 0, 0); 1087 } 1088 1089 /* Indicate we're done! */ 1090 set_bit(ATM_VF_READY, &atm_vcc->flags); 1091 1092 func_exit (); 1093 return 0; 1094} 1095 1096 1097static void fs_close(struct atm_vcc *atm_vcc) 1098{ 1099 struct fs_dev *dev = FS_DEV (atm_vcc->dev); 1100 struct fs_vcc *vcc = FS_VCC (atm_vcc); 1101 struct atm_trafprm * txtp; 1102 struct atm_trafprm * rxtp; 1103 1104 func_enter (); 1105 1106 clear_bit(ATM_VF_READY, &atm_vcc->flags); 1107 1108 fs_dprintk (FS_DEBUG_QSIZE, "--==**[%d]**==--", dev->ntxpckts); 1109 if (vcc->last_skb) { 1110 fs_dprintk (FS_DEBUG_QUEUE, "Waiting for skb %p to be sent.\n", 1111 vcc->last_skb); 1112 /* We're going to wait for the last packet to get sent on this VC. It would 1113 be impolite not to send them don't you think? 1114 XXX 1115 We don't know which packets didn't get sent. So if we get interrupted in 1116 this sleep_on, we'll lose any reference to these packets. Memory leak! 1117 On the other hand, it's awfully convenient that we can abort a "close" that 1118 is taking too long. Maybe just use non-interruptible sleep on? -- REW */ 1119 wait_event_interruptible(vcc->close_wait, !vcc->last_skb); 1120 } 1121 1122 txtp = &atm_vcc->qos.txtp; 1123 rxtp = &atm_vcc->qos.rxtp; 1124 1125 1126 /* See App note XXX (Unpublished as of now) for the reason for the 1127 removal of the "CMD_IMM_INQ" part of the TX_PURGE_INH... -- REW */ 1128 1129 if (DO_DIRECTION (txtp)) { 1130 submit_command (dev, &dev->hp_txq, 1131 QE_CMD_TX_PURGE_INH | /*QE_CMD_IMM_INQ|*/ vcc->channo, 0,0,0); 1132 clear_bit (vcc->channo, dev->tx_inuse); 1133 } 1134 1135 if (DO_DIRECTION (rxtp)) { 1136 submit_command (dev, &dev->hp_txq, 1137 QE_CMD_RX_PURGE_INH | QE_CMD_IMM_INQ | vcc->channo, 0,0,0); 1138 dev->atm_vccs [vcc->channo] = NULL; 1139 1140 /* This means that this is configured as a receive channel */ 1141 if (IS_FS50 (dev)) { 1142 /* Disable the receive filter. Is 0/0 indeed an invalid receive 1143 channel? -- REW. Yes it is. -- Hang. Ok. I'll use -1 1144 (0xfff...) -- REW */ 1145 submit_command (dev, &dev->hp_txq, 1146 QE_CMD_REG_WR | QE_CMD_IMM_INQ, 1147 0x80 + vcc->channo, -1, 0 ); 1148 } 1149 } 1150 1151 fs_dprintk (FS_DEBUG_ALLOC, "Free vcc: %p\n", vcc); 1152 kfree (vcc); 1153 1154 func_exit (); 1155} 1156 1157 1158static int fs_send (struct atm_vcc *atm_vcc, struct sk_buff *skb) 1159{ 1160 struct fs_dev *dev = FS_DEV (atm_vcc->dev); 1161 struct fs_vcc *vcc = FS_VCC (atm_vcc); 1162 struct FS_BPENTRY *td; 1163 1164 func_enter (); 1165 1166 fs_dprintk (FS_DEBUG_TXMEM, "I"); 1167 fs_dprintk (FS_DEBUG_SEND, "Send: atm_vcc %p skb %p vcc %p dev %p\n", 1168 atm_vcc, skb, vcc, dev); 1169 1170 fs_dprintk (FS_DEBUG_ALLOC, "Alloc t-skb: %p (atm_send)\n", skb); 1171 1172 ATM_SKB(skb)->vcc = atm_vcc; 1173 1174 vcc->last_skb = skb; 1175 1176 td = kmalloc (sizeof (struct FS_BPENTRY), GFP_ATOMIC); 1177 fs_dprintk (FS_DEBUG_ALLOC, "Alloc transd: %p(%zd)\n", td, sizeof (struct FS_BPENTRY)); 1178 if (!td) { 1179 /* Oops out of mem */ 1180 return -ENOMEM; 1181 } 1182 1183 fs_dprintk (FS_DEBUG_SEND, "first word in buffer: %x\n", 1184 *(int *) skb->data); 1185 1186 td->flags = TD_EPI | TD_DATA | skb->len; 1187 td->next = 0; 1188 td->bsa = virt_to_bus (skb->data); 1189 td->skb = skb; 1190 td->dev = dev; 1191 dev->ntxpckts++; 1192 1193#ifdef DEBUG_EXTRA 1194 da[qd] = td; 1195 dq[qd].flags = td->flags; 1196 dq[qd].next = td->next; 1197 dq[qd].bsa = td->bsa; 1198 dq[qd].skb = td->skb; 1199 dq[qd].dev = td->dev; 1200 qd++; 1201 if (qd >= 60) qd = 0; 1202#endif 1203 1204 submit_queue (dev, &dev->hp_txq, 1205 QE_TRANSMIT_DE | vcc->channo, 1206 virt_to_bus (td), 0, 1207 virt_to_bus (td)); 1208 1209 fs_dprintk (FS_DEBUG_QUEUE, "in send: txq %d txrq %d\n", 1210 read_fs (dev, Q_EA (dev->hp_txq.offset)) - 1211 read_fs (dev, Q_SA (dev->hp_txq.offset)), 1212 read_fs (dev, Q_EA (dev->tx_relq.offset)) - 1213 read_fs (dev, Q_SA (dev->tx_relq.offset))); 1214 1215 func_exit (); 1216 return 0; 1217} 1218 1219 1220/* Some function placeholders for functions we don't yet support. */ 1221 1222#if 0 1223static int fs_ioctl(struct atm_dev *dev,unsigned int cmd,void __user *arg) 1224{ 1225 func_enter (); 1226 func_exit (); 1227 return -ENOIOCTLCMD; 1228} 1229 1230 1231static int fs_getsockopt(struct atm_vcc *vcc,int level,int optname, 1232 void __user *optval,int optlen) 1233{ 1234 func_enter (); 1235 func_exit (); 1236 return 0; 1237} 1238 1239 1240static int fs_setsockopt(struct atm_vcc *vcc,int level,int optname, 1241 void __user *optval,unsigned int optlen) 1242{ 1243 func_enter (); 1244 func_exit (); 1245 return 0; 1246} 1247 1248 1249static void fs_phy_put(struct atm_dev *dev,unsigned char value, 1250 unsigned long addr) 1251{ 1252 func_enter (); 1253 func_exit (); 1254} 1255 1256 1257static unsigned char fs_phy_get(struct atm_dev *dev,unsigned long addr) 1258{ 1259 func_enter (); 1260 func_exit (); 1261 return 0; 1262} 1263 1264 1265static int fs_change_qos(struct atm_vcc *vcc,struct atm_qos *qos,int flags) 1266{ 1267 func_enter (); 1268 func_exit (); 1269 return 0; 1270}; 1271 1272#endif 1273 1274 1275static const struct atmdev_ops ops = { 1276 .open = fs_open, 1277 .close = fs_close, 1278 .send = fs_send, 1279 .owner = THIS_MODULE, 1280 /* ioctl: fs_ioctl, */ 1281 /* change_qos: fs_change_qos, */ 1282 1283 /* For now implement these internally here... */ 1284 /* phy_put: fs_phy_put, */ 1285 /* phy_get: fs_phy_get, */ 1286}; 1287 1288 1289static void undocumented_pci_fix(struct pci_dev *pdev) 1290{ 1291 u32 tint; 1292 1293 /* The Windows driver says: */ 1294 /* Switch off FireStream Retry Limit Threshold 1295 */ 1296 1297 /* The register at 0x28 is documented as "reserved", no further 1298 comments. */ 1299 1300 pci_read_config_dword (pdev, 0x28, &tint); 1301 if (tint != 0x80) { 1302 tint = 0x80; 1303 pci_write_config_dword (pdev, 0x28, tint); 1304 } 1305} 1306 1307 1308 1309/************************************************************************** 1310 * PHY routines * 1311 **************************************************************************/ 1312 1313static void write_phy(struct fs_dev *dev, int regnum, int val) 1314{ 1315 submit_command (dev, &dev->hp_txq, QE_CMD_PRP_WR | QE_CMD_IMM_INQ, 1316 regnum, val, 0); 1317} 1318 1319static int init_phy(struct fs_dev *dev, struct reginit_item *reginit) 1320{ 1321 int i; 1322 1323 func_enter (); 1324 while (reginit->reg != PHY_EOF) { 1325 if (reginit->reg == PHY_CLEARALL) { 1326 /* "PHY_CLEARALL means clear all registers. Numregisters is in "val". */ 1327 for (i=0;i<reginit->val;i++) { 1328 write_phy (dev, i, 0); 1329 } 1330 } else { 1331 write_phy (dev, reginit->reg, reginit->val); 1332 } 1333 reginit++; 1334 } 1335 func_exit (); 1336 return 0; 1337} 1338 1339static void reset_chip (struct fs_dev *dev) 1340{ 1341 int i; 1342 1343 write_fs (dev, SARMODE0, SARMODE0_SRTS0); 1344 1345 /* Undocumented delay */ 1346 udelay (128); 1347 1348 /* The "internal registers are documented to all reset to zero, but 1349 comments & code in the Windows driver indicates that the pools are 1350 NOT reset. */ 1351 for (i=0;i < FS_NR_FREE_POOLS;i++) { 1352 write_fs (dev, FP_CNF (RXB_FP(i)), 0); 1353 write_fs (dev, FP_SA (RXB_FP(i)), 0); 1354 write_fs (dev, FP_EA (RXB_FP(i)), 0); 1355 write_fs (dev, FP_CNT (RXB_FP(i)), 0); 1356 write_fs (dev, FP_CTU (RXB_FP(i)), 0); 1357 } 1358 1359 /* The same goes for the match channel registers, although those are 1360 NOT documented that way in the Windows driver. -- REW */ 1361 /* The Windows driver DOES write 0 to these registers somewhere in 1362 the init sequence. However, a small hardware-feature, will 1363 prevent reception of data on VPI/VCI = 0/0 (Unless the channel 1364 allocated happens to have no disabled channels that have a lower 1365 number. -- REW */ 1366 1367 /* Clear the match channel registers. */ 1368 if (IS_FS50 (dev)) { 1369 for (i=0;i<FS50_NR_CHANNELS;i++) { 1370 write_fs (dev, 0x200 + i * 4, -1); 1371 } 1372 } 1373} 1374 1375static void *aligned_kmalloc(int size, gfp_t flags, int alignment) 1376{ 1377 void *t; 1378 1379 if (alignment <= 0x10) { 1380 t = kmalloc (size, flags); 1381 if ((unsigned long)t & (alignment-1)) { 1382 printk ("Kmalloc doesn't align things correctly! %p\n", t); 1383 kfree (t); 1384 return aligned_kmalloc (size, flags, alignment * 4); 1385 } 1386 return t; 1387 } 1388 printk (KERN_ERR "Request for > 0x10 alignment not yet implemented (hard!)\n"); 1389 return NULL; 1390} 1391 1392static int init_q(struct fs_dev *dev, struct queue *txq, int queue, 1393 int nentries, int is_rq) 1394{ 1395 int sz = nentries * sizeof (struct FS_QENTRY); 1396 struct FS_QENTRY *p; 1397 1398 func_enter (); 1399 1400 fs_dprintk (FS_DEBUG_INIT, "Initializing queue at %x: %d entries:\n", 1401 queue, nentries); 1402 1403 p = aligned_kmalloc (sz, GFP_KERNEL, 0x10); 1404 fs_dprintk (FS_DEBUG_ALLOC, "Alloc queue: %p(%d)\n", p, sz); 1405 1406 if (!p) return 0; 1407 1408 write_fs (dev, Q_SA(queue), virt_to_bus(p)); 1409 write_fs (dev, Q_EA(queue), virt_to_bus(p+nentries-1)); 1410 write_fs (dev, Q_WP(queue), virt_to_bus(p)); 1411 write_fs (dev, Q_RP(queue), virt_to_bus(p)); 1412 if (is_rq) { 1413 /* Configuration for the receive queue: 0: interrupt immediately, 1414 no pre-warning to empty queues: We do our best to keep the 1415 queue filled anyway. */ 1416 write_fs (dev, Q_CNF(queue), 0 ); 1417 } 1418 1419 txq->sa = p; 1420 txq->ea = p; 1421 txq->offset = queue; 1422 1423 func_exit (); 1424 return 1; 1425} 1426 1427 1428static int init_fp(struct fs_dev *dev, struct freepool *fp, int queue, 1429 int bufsize, int nr_buffers) 1430{ 1431 func_enter (); 1432 1433 fs_dprintk (FS_DEBUG_INIT, "Initializing free pool at %x:\n", queue); 1434 1435 write_fs (dev, FP_CNF(queue), (bufsize * RBFP_RBS) | RBFP_RBSVAL | RBFP_CME); 1436 write_fs (dev, FP_SA(queue), 0); 1437 write_fs (dev, FP_EA(queue), 0); 1438 write_fs (dev, FP_CTU(queue), 0); 1439 write_fs (dev, FP_CNT(queue), 0); 1440 1441 fp->offset = queue; 1442 fp->bufsize = bufsize; 1443 fp->nr_buffers = nr_buffers; 1444 1445 func_exit (); 1446 return 1; 1447} 1448 1449 1450static inline int nr_buffers_in_freepool (struct fs_dev *dev, struct freepool *fp) 1451{ 1452#if 0 1453 /* This seems to be unreliable.... */ 1454 return read_fs (dev, FP_CNT (fp->offset)); 1455#else 1456 return fp->n; 1457#endif 1458} 1459 1460 1461/* Check if this gets going again if a pool ever runs out. -- Yes, it 1462 does. I've seen "receive abort: no buffers" and things started 1463 working again after that... -- REW */ 1464 1465static void top_off_fp (struct fs_dev *dev, struct freepool *fp, 1466 gfp_t gfp_flags) 1467{ 1468 struct FS_BPENTRY *qe, *ne; 1469 struct sk_buff *skb; 1470 int n = 0; 1471 u32 qe_tmp; 1472 1473 fs_dprintk (FS_DEBUG_QUEUE, "Topping off queue at %x (%d-%d/%d)\n", 1474 fp->offset, read_fs (dev, FP_CNT (fp->offset)), fp->n, 1475 fp->nr_buffers); 1476 while (nr_buffers_in_freepool(dev, fp) < fp->nr_buffers) { 1477 1478 skb = alloc_skb (fp->bufsize, gfp_flags); 1479 fs_dprintk (FS_DEBUG_ALLOC, "Alloc rec-skb: %p(%d)\n", skb, fp->bufsize); 1480 if (!skb) break; 1481 ne = kmalloc (sizeof (struct FS_BPENTRY), gfp_flags); 1482 fs_dprintk (FS_DEBUG_ALLOC, "Alloc rec-d: %p(%zd)\n", ne, sizeof (struct FS_BPENTRY)); 1483 if (!ne) { 1484 fs_dprintk (FS_DEBUG_ALLOC, "Free rec-skb: %p\n", skb); 1485 dev_kfree_skb_any (skb); 1486 break; 1487 } 1488 1489 fs_dprintk (FS_DEBUG_QUEUE, "Adding skb %p desc %p -> %p(%p) ", 1490 skb, ne, skb->data, skb->head); 1491 n++; 1492 ne->flags = FP_FLAGS_EPI | fp->bufsize; 1493 ne->next = virt_to_bus (NULL); 1494 ne->bsa = virt_to_bus (skb->data); 1495 ne->aal_bufsize = fp->bufsize; 1496 ne->skb = skb; 1497 ne->fp = fp; 1498 1499 /* 1500 * FIXME: following code encodes and decodes 1501 * machine pointers (could be 64-bit) into a 1502 * 32-bit register. 1503 */ 1504 1505 qe_tmp = read_fs (dev, FP_EA(fp->offset)); 1506 fs_dprintk (FS_DEBUG_QUEUE, "link at %x\n", qe_tmp); 1507 if (qe_tmp) { 1508 qe = bus_to_virt ((long) qe_tmp); 1509 qe->next = virt_to_bus(ne); 1510 qe->flags &= ~FP_FLAGS_EPI; 1511 } else 1512 write_fs (dev, FP_SA(fp->offset), virt_to_bus(ne)); 1513 1514 write_fs (dev, FP_EA(fp->offset), virt_to_bus (ne)); 1515 fp->n++; /* XXX Atomic_inc? */ 1516 write_fs (dev, FP_CTU(fp->offset), 1); 1517 } 1518 1519 fs_dprintk (FS_DEBUG_QUEUE, "Added %d entries. \n", n); 1520} 1521 1522static void free_queue(struct fs_dev *dev, struct queue *txq) 1523{ 1524 func_enter (); 1525 1526 write_fs (dev, Q_SA(txq->offset), 0); 1527 write_fs (dev, Q_EA(txq->offset), 0); 1528 write_fs (dev, Q_RP(txq->offset), 0); 1529 write_fs (dev, Q_WP(txq->offset), 0); 1530 /* Configuration ? */ 1531 1532 fs_dprintk (FS_DEBUG_ALLOC, "Free queue: %p\n", txq->sa); 1533 kfree (txq->sa); 1534 1535 func_exit (); 1536} 1537 1538static void free_freepool(struct fs_dev *dev, struct freepool *fp) 1539{ 1540 func_enter (); 1541 1542 write_fs (dev, FP_CNF(fp->offset), 0); 1543 write_fs (dev, FP_SA (fp->offset), 0); 1544 write_fs (dev, FP_EA (fp->offset), 0); 1545 write_fs (dev, FP_CNT(fp->offset), 0); 1546 write_fs (dev, FP_CTU(fp->offset), 0); 1547 1548 func_exit (); 1549} 1550 1551 1552 1553static irqreturn_t fs_irq (int irq, void *dev_id) 1554{ 1555 int i; 1556 u32 status; 1557 struct fs_dev *dev = dev_id; 1558 1559 status = read_fs (dev, ISR); 1560 if (!status) 1561 return IRQ_NONE; 1562 1563 func_enter (); 1564 1565#ifdef IRQ_RATE_LIMIT 1566 /* Aaargh! I'm ashamed. This costs more lines-of-code than the actual 1567 interrupt routine!. (Well, used to when I wrote that comment) -- REW */ 1568 { 1569 static int lastjif; 1570 static int nintr=0; 1571 1572 if (lastjif == jiffies) { 1573 if (++nintr > IRQ_RATE_LIMIT) { 1574 free_irq (dev->irq, dev_id); 1575 printk (KERN_ERR "fs: Too many interrupts. Turning off interrupt %d.\n", 1576 dev->irq); 1577 } 1578 } else { 1579 lastjif = jiffies; 1580 nintr = 0; 1581 } 1582 } 1583#endif 1584 fs_dprintk (FS_DEBUG_QUEUE, "in intr: txq %d txrq %d\n", 1585 read_fs (dev, Q_EA (dev->hp_txq.offset)) - 1586 read_fs (dev, Q_SA (dev->hp_txq.offset)), 1587 read_fs (dev, Q_EA (dev->tx_relq.offset)) - 1588 read_fs (dev, Q_SA (dev->tx_relq.offset))); 1589 1590 /* print the bits in the ISR register. */ 1591 if (fs_debug & FS_DEBUG_IRQ) { 1592 /* The FS_DEBUG things are unnecessary here. But this way it is 1593 clear for grep that these are debug prints. */ 1594 fs_dprintk (FS_DEBUG_IRQ, "IRQ status:"); 1595 for (i=0;i<27;i++) 1596 if (status & (1 << i)) 1597 fs_dprintk (FS_DEBUG_IRQ, " %s", irq_bitname[i]); 1598 fs_dprintk (FS_DEBUG_IRQ, "\n"); 1599 } 1600 1601 if (status & ISR_RBRQ0_W) { 1602 fs_dprintk (FS_DEBUG_IRQ, "Iiiin-coming (0)!!!!\n"); 1603 process_incoming (dev, &dev->rx_rq[0]); 1604 /* items mentioned on RBRQ0 are from FP 0 or 1. */ 1605 top_off_fp (dev, &dev->rx_fp[0], GFP_ATOMIC); 1606 top_off_fp (dev, &dev->rx_fp[1], GFP_ATOMIC); 1607 } 1608 1609 if (status & ISR_RBRQ1_W) { 1610 fs_dprintk (FS_DEBUG_IRQ, "Iiiin-coming (1)!!!!\n"); 1611 process_incoming (dev, &dev->rx_rq[1]); 1612 top_off_fp (dev, &dev->rx_fp[2], GFP_ATOMIC); 1613 top_off_fp (dev, &dev->rx_fp[3], GFP_ATOMIC); 1614 } 1615 1616 if (status & ISR_RBRQ2_W) { 1617 fs_dprintk (FS_DEBUG_IRQ, "Iiiin-coming (2)!!!!\n"); 1618 process_incoming (dev, &dev->rx_rq[2]); 1619 top_off_fp (dev, &dev->rx_fp[4], GFP_ATOMIC); 1620 top_off_fp (dev, &dev->rx_fp[5], GFP_ATOMIC); 1621 } 1622 1623 if (status & ISR_RBRQ3_W) { 1624 fs_dprintk (FS_DEBUG_IRQ, "Iiiin-coming (3)!!!!\n"); 1625 process_incoming (dev, &dev->rx_rq[3]); 1626 top_off_fp (dev, &dev->rx_fp[6], GFP_ATOMIC); 1627 top_off_fp (dev, &dev->rx_fp[7], GFP_ATOMIC); 1628 } 1629 1630 if (status & ISR_CSQ_W) { 1631 fs_dprintk (FS_DEBUG_IRQ, "Command executed ok!\n"); 1632 process_return_queue (dev, &dev->st_q); 1633 } 1634 1635 if (status & ISR_TBRQ_W) { 1636 fs_dprintk (FS_DEBUG_IRQ, "Data transmitted!\n"); 1637 process_txdone_queue (dev, &dev->tx_relq); 1638 } 1639 1640 func_exit (); 1641 return IRQ_HANDLED; 1642} 1643 1644 1645#ifdef FS_POLL_FREQ 1646static void fs_poll (struct timer_list *t) 1647{ 1648 struct fs_dev *dev = from_timer(dev, t, timer); 1649 1650 fs_irq (0, dev); 1651 dev->timer.expires = jiffies + FS_POLL_FREQ; 1652 add_timer (&dev->timer); 1653} 1654#endif 1655 1656static int fs_init(struct fs_dev *dev) 1657{ 1658 struct pci_dev *pci_dev; 1659 int isr, to; 1660 int i; 1661 1662 func_enter (); 1663 pci_dev = dev->pci_dev; 1664 1665 printk (KERN_INFO "found a FireStream %d card, base %16llx, irq%d.\n", 1666 IS_FS50(dev)?50:155, 1667 (unsigned long long)pci_resource_start(pci_dev, 0), 1668 dev->pci_dev->irq); 1669 1670 if (fs_debug & FS_DEBUG_INIT) 1671 my_hd ((unsigned char *) dev, sizeof (*dev)); 1672 1673 undocumented_pci_fix (pci_dev); 1674 1675 dev->hw_base = pci_resource_start(pci_dev, 0); 1676 1677 dev->base = ioremap(dev->hw_base, 0x1000); 1678 if (!dev->base) 1679 return 1; 1680 1681 reset_chip (dev); 1682 1683 write_fs (dev, SARMODE0, 0 1684 | (0 * SARMODE0_SHADEN) /* We don't use shadow registers. */ 1685 | (1 * SARMODE0_INTMODE_READCLEAR) 1686 | (1 * SARMODE0_CWRE) 1687 | (IS_FS50(dev) ? SARMODE0_PRPWT_FS50_5: 1688 SARMODE0_PRPWT_FS155_3) 1689 | (1 * SARMODE0_CALSUP_1) 1690 | (IS_FS50(dev) ? (0 1691 | SARMODE0_RXVCS_32 1692 | SARMODE0_ABRVCS_32 1693 | SARMODE0_TXVCS_32): 1694 (0 1695 | SARMODE0_RXVCS_1k 1696 | SARMODE0_ABRVCS_1k 1697 | SARMODE0_TXVCS_1k))); 1698 1699 /* 10ms * 100 is 1 second. That should be enough, as AN3:9 says it takes 1700 1ms. */ 1701 to = 100; 1702 while (--to) { 1703 isr = read_fs (dev, ISR); 1704 1705 /* This bit is documented as "RESERVED" */ 1706 if (isr & ISR_INIT_ERR) { 1707 printk (KERN_ERR "Error initializing the FS... \n"); 1708 goto unmap; 1709 } 1710 if (isr & ISR_INIT) { 1711 fs_dprintk (FS_DEBUG_INIT, "Ha! Initialized OK!\n"); 1712 break; 1713 } 1714 1715 /* Try again after 10ms. */ 1716 msleep(10); 1717 } 1718 1719 if (!to) { 1720 printk (KERN_ERR "timeout initializing the FS... \n"); 1721 goto unmap; 1722 } 1723 1724 /* XXX fix for fs155 */ 1725 dev->channel_mask = 0x1f; 1726 dev->channo = 0; 1727 1728 /* AN3: 10 */ 1729 write_fs (dev, SARMODE1, 0 1730 | (fs_keystream * SARMODE1_DEFHEC) /* XXX PHY */ 1731 | ((loopback == 1) * SARMODE1_TSTLP) /* XXX Loopback mode enable... */ 1732 | (1 * SARMODE1_DCRM) 1733 | (1 * SARMODE1_DCOAM) 1734 | (0 * SARMODE1_OAMCRC) 1735 | (0 * SARMODE1_DUMPE) 1736 | (0 * SARMODE1_GPLEN) 1737 | (0 * SARMODE1_GNAM) 1738 | (0 * SARMODE1_GVAS) 1739 | (0 * SARMODE1_GPAS) 1740 | (1 * SARMODE1_GPRI) 1741 | (0 * SARMODE1_PMS) 1742 | (0 * SARMODE1_GFCR) 1743 | (1 * SARMODE1_HECM2) 1744 | (1 * SARMODE1_HECM1) 1745 | (1 * SARMODE1_HECM0) 1746 | (1 << 12) /* That's what hang's driver does. Program to 0 */ 1747 | (0 * 0xff) /* XXX FS155 */); 1748 1749 1750 /* Cal prescale etc */ 1751 1752 /* AN3: 11 */ 1753 write_fs (dev, TMCONF, 0x0000000f); 1754 write_fs (dev, CALPRESCALE, 0x01010101 * num); 1755 write_fs (dev, 0x80, 0x000F00E4); 1756 1757 /* AN3: 12 */ 1758 write_fs (dev, CELLOSCONF, 0 1759 | ( 0 * CELLOSCONF_CEN) 1760 | ( CELLOSCONF_SC1) 1761 | (0x80 * CELLOSCONF_COBS) 1762 | (num * CELLOSCONF_COPK) /* Changed from 0xff to 0x5a */ 1763 | (num * CELLOSCONF_COST));/* after a hint from Hang. 1764 * performance jumped 50->70... */ 1765 1766 /* Magic value by Hang */ 1767 write_fs (dev, CELLOSCONF_COST, 0x0B809191); 1768 1769 if (IS_FS50 (dev)) { 1770 write_fs (dev, RAS0, RAS0_DCD_XHLT); 1771 dev->atm_dev->ci_range.vpi_bits = 12; 1772 dev->atm_dev->ci_range.vci_bits = 16; 1773 dev->nchannels = FS50_NR_CHANNELS; 1774 } else { 1775 write_fs (dev, RAS0, RAS0_DCD_XHLT 1776 | (((1 << FS155_VPI_BITS) - 1) * RAS0_VPSEL) 1777 | (((1 << FS155_VCI_BITS) - 1) * RAS0_VCSEL)); 1778 /* We can chose the split arbitrarily. We might be able to 1779 support more. Whatever. This should do for now. */ 1780 dev->atm_dev->ci_range.vpi_bits = FS155_VPI_BITS; 1781 dev->atm_dev->ci_range.vci_bits = FS155_VCI_BITS; 1782 1783 /* Address bits we can't use should be compared to 0. */ 1784 write_fs (dev, RAC, 0); 1785 1786 /* Manual (AN9, page 6) says ASF1=0 means compare Utopia address 1787 * too. I can't find ASF1 anywhere. Anyway, we AND with just the 1788 * other bits, then compare with 0, which is exactly what we 1789 * want. */ 1790 write_fs (dev, RAM, (1 << (28 - FS155_VPI_BITS - FS155_VCI_BITS)) - 1); 1791 dev->nchannels = FS155_NR_CHANNELS; 1792 } 1793 dev->atm_vccs = kcalloc (dev->nchannels, sizeof (struct atm_vcc *), 1794 GFP_KERNEL); 1795 fs_dprintk (FS_DEBUG_ALLOC, "Alloc atmvccs: %p(%zd)\n", 1796 dev->atm_vccs, dev->nchannels * sizeof (struct atm_vcc *)); 1797 1798 if (!dev->atm_vccs) { 1799 printk (KERN_WARNING "Couldn't allocate memory for VCC buffers. Woops!\n"); 1800 /* XXX Clean up..... */ 1801 goto unmap; 1802 } 1803 1804 dev->tx_inuse = kzalloc (dev->nchannels / 8 /* bits/byte */ , GFP_KERNEL); 1805 fs_dprintk (FS_DEBUG_ALLOC, "Alloc tx_inuse: %p(%d)\n", 1806 dev->atm_vccs, dev->nchannels / 8); 1807 1808 if (!dev->tx_inuse) { 1809 printk (KERN_WARNING "Couldn't allocate memory for tx_inuse bits!\n"); 1810 /* XXX Clean up..... */ 1811 goto unmap; 1812 } 1813 /* -- RAS1 : FS155 and 50 differ. Default (0) should be OK for both */ 1814 /* -- RAS2 : FS50 only: Default is OK. */ 1815 1816 /* DMAMODE, default should be OK. -- REW */ 1817 write_fs (dev, DMAMR, DMAMR_TX_MODE_FULL); 1818 1819 init_q (dev, &dev->hp_txq, TX_PQ(TXQ_HP), TXQ_NENTRIES, 0); 1820 init_q (dev, &dev->lp_txq, TX_PQ(TXQ_LP), TXQ_NENTRIES, 0); 1821 init_q (dev, &dev->tx_relq, TXB_RQ, TXQ_NENTRIES, 1); 1822 init_q (dev, &dev->st_q, ST_Q, TXQ_NENTRIES, 1); 1823 1824 for (i=0;i < FS_NR_FREE_POOLS;i++) { 1825 init_fp (dev, &dev->rx_fp[i], RXB_FP(i), 1826 rx_buf_sizes[i], rx_pool_sizes[i]); 1827 top_off_fp (dev, &dev->rx_fp[i], GFP_KERNEL); 1828 } 1829 1830 1831 for (i=0;i < FS_NR_RX_QUEUES;i++) 1832 init_q (dev, &dev->rx_rq[i], RXB_RQ(i), RXRQ_NENTRIES, 1); 1833 1834 dev->irq = pci_dev->irq; 1835 if (request_irq (dev->irq, fs_irq, IRQF_SHARED, "firestream", dev)) { 1836 printk (KERN_WARNING "couldn't get irq %d for firestream.\n", pci_dev->irq); 1837 /* XXX undo all previous stuff... */ 1838 goto unmap; 1839 } 1840 fs_dprintk (FS_DEBUG_INIT, "Grabbed irq %d for dev at %p.\n", dev->irq, dev); 1841 1842 /* We want to be notified of most things. Just the statistics count 1843 overflows are not interesting */ 1844 write_fs (dev, IMR, 0 1845 | ISR_RBRQ0_W 1846 | ISR_RBRQ1_W 1847 | ISR_RBRQ2_W 1848 | ISR_RBRQ3_W 1849 | ISR_TBRQ_W 1850 | ISR_CSQ_W); 1851 1852 write_fs (dev, SARMODE0, 0 1853 | (0 * SARMODE0_SHADEN) /* We don't use shadow registers. */ 1854 | (1 * SARMODE0_GINT) 1855 | (1 * SARMODE0_INTMODE_READCLEAR) 1856 | (0 * SARMODE0_CWRE) 1857 | (IS_FS50(dev)?SARMODE0_PRPWT_FS50_5: 1858 SARMODE0_PRPWT_FS155_3) 1859 | (1 * SARMODE0_CALSUP_1) 1860 | (IS_FS50 (dev)?(0 1861 | SARMODE0_RXVCS_32 1862 | SARMODE0_ABRVCS_32 1863 | SARMODE0_TXVCS_32): 1864 (0 1865 | SARMODE0_RXVCS_1k 1866 | SARMODE0_ABRVCS_1k 1867 | SARMODE0_TXVCS_1k)) 1868 | (1 * SARMODE0_RUN)); 1869 1870 init_phy (dev, PHY_NTC_INIT); 1871 1872 if (loopback == 2) { 1873 write_phy (dev, 0x39, 0x000e); 1874 } 1875 1876#ifdef FS_POLL_FREQ 1877 timer_setup(&dev->timer, fs_poll, 0); 1878 dev->timer.expires = jiffies + FS_POLL_FREQ; 1879 add_timer (&dev->timer); 1880#endif 1881 1882 dev->atm_dev->dev_data = dev; 1883 1884 func_exit (); 1885 return 0; 1886unmap: 1887 iounmap(dev->base); 1888 return 1; 1889} 1890 1891static int firestream_init_one(struct pci_dev *pci_dev, 1892 const struct pci_device_id *ent) 1893{ 1894 struct atm_dev *atm_dev; 1895 struct fs_dev *fs_dev; 1896 1897 if (pci_enable_device(pci_dev)) 1898 goto err_out; 1899 1900 fs_dev = kzalloc (sizeof (struct fs_dev), GFP_KERNEL); 1901 fs_dprintk (FS_DEBUG_ALLOC, "Alloc fs-dev: %p(%zd)\n", 1902 fs_dev, sizeof (struct fs_dev)); 1903 if (!fs_dev) 1904 goto err_out; 1905 atm_dev = atm_dev_register("fs", &pci_dev->dev, &ops, -1, NULL); 1906 if (!atm_dev) 1907 goto err_out_free_fs_dev; 1908 1909 fs_dev->pci_dev = pci_dev; 1910 fs_dev->atm_dev = atm_dev; 1911 fs_dev->flags = ent->driver_data; 1912 1913 if (fs_init(fs_dev)) 1914 goto err_out_free_atm_dev; 1915 1916 fs_dev->next = fs_boards; 1917 fs_boards = fs_dev; 1918 return 0; 1919 1920 err_out_free_atm_dev: 1921 atm_dev_deregister(atm_dev); 1922 err_out_free_fs_dev: 1923 kfree(fs_dev); 1924 err_out: 1925 return -ENODEV; 1926} 1927 1928static void firestream_remove_one(struct pci_dev *pdev) 1929{ 1930 int i; 1931 struct fs_dev *dev, *nxtdev; 1932 struct fs_vcc *vcc; 1933 struct FS_BPENTRY *fp, *nxt; 1934 1935 func_enter (); 1936 1937#if 0 1938 printk ("hptxq:\n"); 1939 for (i=0;i<60;i++) { 1940 printk ("%d: %08x %08x %08x %08x \n", 1941 i, pq[qp].cmd, pq[qp].p0, pq[qp].p1, pq[qp].p2); 1942 qp++; 1943 if (qp >= 60) qp = 0; 1944 } 1945 1946 printk ("descriptors:\n"); 1947 for (i=0;i<60;i++) { 1948 printk ("%d: %p: %08x %08x %p %p\n", 1949 i, da[qd], dq[qd].flags, dq[qd].bsa, dq[qd].skb, dq[qd].dev); 1950 qd++; 1951 if (qd >= 60) qd = 0; 1952 } 1953#endif 1954 1955 for (dev = fs_boards;dev != NULL;dev=nxtdev) { 1956 fs_dprintk (FS_DEBUG_CLEANUP, "Releasing resources for dev at %p.\n", dev); 1957 1958 /* XXX Hit all the tx channels too! */ 1959 1960 for (i=0;i < dev->nchannels;i++) { 1961 if (dev->atm_vccs[i]) { 1962 vcc = FS_VCC (dev->atm_vccs[i]); 1963 submit_command (dev, &dev->hp_txq, 1964 QE_CMD_TX_PURGE_INH | QE_CMD_IMM_INQ | vcc->channo, 0,0,0); 1965 submit_command (dev, &dev->hp_txq, 1966 QE_CMD_RX_PURGE_INH | QE_CMD_IMM_INQ | vcc->channo, 0,0,0); 1967 1968 } 1969 } 1970 1971 /* XXX Wait a while for the chip to release all buffers. */ 1972 1973 for (i=0;i < FS_NR_FREE_POOLS;i++) { 1974 for (fp=bus_to_virt (read_fs (dev, FP_SA(dev->rx_fp[i].offset))); 1975 !(fp->flags & FP_FLAGS_EPI);fp = nxt) { 1976 fs_dprintk (FS_DEBUG_ALLOC, "Free rec-skb: %p\n", fp->skb); 1977 dev_kfree_skb_any (fp->skb); 1978 nxt = bus_to_virt (fp->next); 1979 fs_dprintk (FS_DEBUG_ALLOC, "Free rec-d: %p\n", fp); 1980 kfree (fp); 1981 } 1982 fs_dprintk (FS_DEBUG_ALLOC, "Free rec-skb: %p\n", fp->skb); 1983 dev_kfree_skb_any (fp->skb); 1984 fs_dprintk (FS_DEBUG_ALLOC, "Free rec-d: %p\n", fp); 1985 kfree (fp); 1986 } 1987 1988 /* Hang the chip in "reset", prevent it clobbering memory that is 1989 no longer ours. */ 1990 reset_chip (dev); 1991 1992 fs_dprintk (FS_DEBUG_CLEANUP, "Freeing irq%d.\n", dev->irq); 1993 free_irq (dev->irq, dev); 1994 del_timer_sync (&dev->timer); 1995 1996 atm_dev_deregister(dev->atm_dev); 1997 free_queue (dev, &dev->hp_txq); 1998 free_queue (dev, &dev->lp_txq); 1999 free_queue (dev, &dev->tx_relq); 2000 free_queue (dev, &dev->st_q); 2001 2002 fs_dprintk (FS_DEBUG_ALLOC, "Free atmvccs: %p\n", dev->atm_vccs); 2003 kfree (dev->atm_vccs); 2004 2005 for (i=0;i< FS_NR_FREE_POOLS;i++) 2006 free_freepool (dev, &dev->rx_fp[i]); 2007 2008 for (i=0;i < FS_NR_RX_QUEUES;i++) 2009 free_queue (dev, &dev->rx_rq[i]); 2010 2011 iounmap(dev->base); 2012 fs_dprintk (FS_DEBUG_ALLOC, "Free fs-dev: %p\n", dev); 2013 nxtdev = dev->next; 2014 kfree (dev); 2015 } 2016 2017 func_exit (); 2018} 2019 2020static const struct pci_device_id firestream_pci_tbl[] = { 2021 { PCI_VDEVICE(FUJITSU_ME, PCI_DEVICE_ID_FUJITSU_FS50), FS_IS50}, 2022 { PCI_VDEVICE(FUJITSU_ME, PCI_DEVICE_ID_FUJITSU_FS155), FS_IS155}, 2023 { 0, } 2024}; 2025 2026MODULE_DEVICE_TABLE(pci, firestream_pci_tbl); 2027 2028static struct pci_driver firestream_driver = { 2029 .name = "firestream", 2030 .id_table = firestream_pci_tbl, 2031 .probe = firestream_init_one, 2032 .remove = firestream_remove_one, 2033}; 2034 2035static int __init firestream_init_module (void) 2036{ 2037 int error; 2038 2039 func_enter (); 2040 error = pci_register_driver(&firestream_driver); 2041 func_exit (); 2042 return error; 2043} 2044 2045static void __exit firestream_cleanup_module(void) 2046{ 2047 pci_unregister_driver(&firestream_driver); 2048} 2049 2050module_init(firestream_init_module); 2051module_exit(firestream_cleanup_module); 2052 2053MODULE_LICENSE("GPL"); 2054 2055 2056 2057