1// SPDX-License-Identifier: GPL-2.0 2/* 3 * Exceptions for specific devices. Usually work-arounds for fatal design flaws. 4 */ 5 6#include <linux/delay.h> 7#include <linux/dmi.h> 8#include <linux/pci.h> 9#include <linux/vgaarb.h> 10#include <asm/amd_nb.h> 11#include <asm/hpet.h> 12#include <asm/pci_x86.h> 13 14static void pci_fixup_i450nx(struct pci_dev *d) 15{ 16 /* 17 * i450NX -- Find and scan all secondary buses on all PXB's. 18 */ 19 int pxb, reg; 20 u8 busno, suba, subb; 21 22 dev_warn(&d->dev, "Searching for i450NX host bridges\n"); 23 reg = 0xd0; 24 for(pxb = 0; pxb < 2; pxb++) { 25 pci_read_config_byte(d, reg++, &busno); 26 pci_read_config_byte(d, reg++, &suba); 27 pci_read_config_byte(d, reg++, &subb); 28 dev_dbg(&d->dev, "i450NX PXB %d: %02x/%02x/%02x\n", pxb, busno, 29 suba, subb); 30 if (busno) 31 pcibios_scan_root(busno); /* Bus A */ 32 if (suba < subb) 33 pcibios_scan_root(suba+1); /* Bus B */ 34 } 35 pcibios_last_bus = -1; 36} 37DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82451NX, pci_fixup_i450nx); 38 39static void pci_fixup_i450gx(struct pci_dev *d) 40{ 41 /* 42 * i450GX and i450KX -- Find and scan all secondary buses. 43 * (called separately for each PCI bridge found) 44 */ 45 u8 busno; 46 pci_read_config_byte(d, 0x4a, &busno); 47 dev_info(&d->dev, "i440KX/GX host bridge; secondary bus %02x\n", busno); 48 pcibios_scan_root(busno); 49 pcibios_last_bus = -1; 50} 51DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454GX, pci_fixup_i450gx); 52 53static void pci_fixup_umc_ide(struct pci_dev *d) 54{ 55 /* 56 * UM8886BF IDE controller sets region type bits incorrectly, 57 * therefore they look like memory despite of them being I/O. 58 */ 59 int i; 60 61 dev_warn(&d->dev, "Fixing base address flags\n"); 62 for(i = 0; i < 4; i++) 63 d->resource[i].flags |= PCI_BASE_ADDRESS_SPACE_IO; 64} 65DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8886BF, pci_fixup_umc_ide); 66 67static void pci_fixup_latency(struct pci_dev *d) 68{ 69 /* 70 * SiS 5597 and 5598 chipsets require latency timer set to 71 * at most 32 to avoid lockups. 72 */ 73 dev_dbg(&d->dev, "Setting max latency to 32\n"); 74 pcibios_max_latency = 32; 75} 76DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5597, pci_fixup_latency); 77DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5598, pci_fixup_latency); 78 79static void pci_fixup_piix4_acpi(struct pci_dev *d) 80{ 81 /* 82 * PIIX4 ACPI device: hardwired IRQ9 83 */ 84 d->irq = 9; 85} 86DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, pci_fixup_piix4_acpi); 87 88/* 89 * Addresses issues with problems in the memory write queue timer in 90 * certain VIA Northbridges. This bugfix is per VIA's specifications, 91 * except for the KL133/KM133: clearing bit 5 on those Northbridges seems 92 * to trigger a bug in its integrated ProSavage video card, which 93 * causes screen corruption. We only clear bits 6 and 7 for that chipset, 94 * until VIA can provide us with definitive information on why screen 95 * corruption occurs, and what exactly those bits do. 96 * 97 * VIA 8363,8622,8361 Northbridges: 98 * - bits 5, 6, 7 at offset 0x55 need to be turned off 99 * VIA 8367 (KT266x) Northbridges: 100 * - bits 5, 6, 7 at offset 0x95 need to be turned off 101 * VIA 8363 rev 0x81/0x84 (KL133/KM133) Northbridges: 102 * - bits 6, 7 at offset 0x55 need to be turned off 103 */ 104 105#define VIA_8363_KL133_REVISION_ID 0x81 106#define VIA_8363_KM133_REVISION_ID 0x84 107 108static void pci_fixup_via_northbridge_bug(struct pci_dev *d) 109{ 110 u8 v; 111 int where = 0x55; 112 int mask = 0x1f; /* clear bits 5, 6, 7 by default */ 113 114 if (d->device == PCI_DEVICE_ID_VIA_8367_0) { 115 /* fix pci bus latency issues resulted by NB bios error 116 it appears on bug free^Wreduced kt266x's bios forces 117 NB latency to zero */ 118 pci_write_config_byte(d, PCI_LATENCY_TIMER, 0); 119 120 where = 0x95; /* the memory write queue timer register is 121 different for the KT266x's: 0x95 not 0x55 */ 122 } else if (d->device == PCI_DEVICE_ID_VIA_8363_0 && 123 (d->revision == VIA_8363_KL133_REVISION_ID || 124 d->revision == VIA_8363_KM133_REVISION_ID)) { 125 mask = 0x3f; /* clear only bits 6 and 7; clearing bit 5 126 causes screen corruption on the KL133/KM133 */ 127 } 128 129 pci_read_config_byte(d, where, &v); 130 if (v & ~mask) { 131 dev_warn(&d->dev, "Disabling VIA memory write queue (PCI ID %04x, rev %02x): [%02x] %02x & %02x -> %02x\n", \ 132 d->device, d->revision, where, v, mask, v & mask); 133 v &= mask; 134 pci_write_config_byte(d, where, v); 135 } 136} 137DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, pci_fixup_via_northbridge_bug); 138DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8622, pci_fixup_via_northbridge_bug); 139DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, pci_fixup_via_northbridge_bug); 140DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8367_0, pci_fixup_via_northbridge_bug); 141DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, pci_fixup_via_northbridge_bug); 142DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8622, pci_fixup_via_northbridge_bug); 143DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, pci_fixup_via_northbridge_bug); 144DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8367_0, pci_fixup_via_northbridge_bug); 145 146/* 147 * For some reasons Intel decided that certain parts of their 148 * 815, 845 and some other chipsets must look like PCI-to-PCI bridges 149 * while they are obviously not. The 82801 family (AA, AB, BAM/CAM, 150 * BA/CA/DB and E) PCI bridges are actually HUB-to-PCI ones, according 151 * to Intel terminology. These devices do forward all addresses from 152 * system to PCI bus no matter what are their window settings, so they are 153 * "transparent" (or subtractive decoding) from programmers point of view. 154 */ 155static void pci_fixup_transparent_bridge(struct pci_dev *dev) 156{ 157 if ((dev->device & 0xff00) == 0x2400) 158 dev->transparent = 1; 159} 160DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, 161 PCI_CLASS_BRIDGE_PCI, 8, pci_fixup_transparent_bridge); 162 163/* 164 * Fixup for C1 Halt Disconnect problem on nForce2 systems. 165 * 166 * From information provided by "Allen Martin" <AMartin@nvidia.com>: 167 * 168 * A hang is caused when the CPU generates a very fast CONNECT/HALT cycle 169 * sequence. Workaround is to set the SYSTEM_IDLE_TIMEOUT to 80 ns. 170 * This allows the state-machine and timer to return to a proper state within 171 * 80 ns of the CONNECT and probe appearing together. Since the CPU will not 172 * issue another HALT within 80 ns of the initial HALT, the failure condition 173 * is avoided. 174 */ 175static void pci_fixup_nforce2(struct pci_dev *dev) 176{ 177 u32 val; 178 179 /* 180 * Chip Old value New value 181 * C17 0x1F0FFF01 0x1F01FF01 182 * C18D 0x9F0FFF01 0x9F01FF01 183 * 184 * Northbridge chip version may be determined by 185 * reading the PCI revision ID (0xC1 or greater is C18D). 186 */ 187 pci_read_config_dword(dev, 0x6c, &val); 188 189 /* 190 * Apply fixup if needed, but don't touch disconnect state 191 */ 192 if ((val & 0x00FF0000) != 0x00010000) { 193 dev_warn(&dev->dev, "nForce2 C1 Halt Disconnect fixup\n"); 194 pci_write_config_dword(dev, 0x6c, (val & 0xFF00FFFF) | 0x00010000); 195 } 196} 197DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2, pci_fixup_nforce2); 198DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2, pci_fixup_nforce2); 199 200/* Max PCI Express root ports */ 201#define MAX_PCIEROOT 6 202static int quirk_aspm_offset[MAX_PCIEROOT << 3]; 203 204#define GET_INDEX(a, b) ((((a) - PCI_DEVICE_ID_INTEL_MCH_PA) << 3) + ((b) & 7)) 205 206static int quirk_pcie_aspm_read(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 *value) 207{ 208 return raw_pci_read(pci_domain_nr(bus), bus->number, 209 devfn, where, size, value); 210} 211 212/* 213 * Replace the original pci bus ops for write with a new one that will filter 214 * the request to insure ASPM cannot be enabled. 215 */ 216static int quirk_pcie_aspm_write(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 value) 217{ 218 u8 offset; 219 220 offset = quirk_aspm_offset[GET_INDEX(bus->self->device, devfn)]; 221 222 if ((offset) && (where == offset)) 223 value = value & ~PCI_EXP_LNKCTL_ASPMC; 224 225 return raw_pci_write(pci_domain_nr(bus), bus->number, 226 devfn, where, size, value); 227} 228 229static struct pci_ops quirk_pcie_aspm_ops = { 230 .read = quirk_pcie_aspm_read, 231 .write = quirk_pcie_aspm_write, 232}; 233 234/* 235 * Prevents PCI Express ASPM (Active State Power Management) being enabled. 236 * 237 * Save the register offset, where the ASPM control bits are located, 238 * for each PCI Express device that is in the device list of 239 * the root port in an array for fast indexing. Replace the bus ops 240 * with the modified one. 241 */ 242static void pcie_rootport_aspm_quirk(struct pci_dev *pdev) 243{ 244 int i; 245 struct pci_bus *pbus; 246 struct pci_dev *dev; 247 248 if ((pbus = pdev->subordinate) == NULL) 249 return; 250 251 /* 252 * Check if the DID of pdev matches one of the six root ports. This 253 * check is needed in the case this function is called directly by the 254 * hot-plug driver. 255 */ 256 if ((pdev->device < PCI_DEVICE_ID_INTEL_MCH_PA) || 257 (pdev->device > PCI_DEVICE_ID_INTEL_MCH_PC1)) 258 return; 259 260 if (list_empty(&pbus->devices)) { 261 /* 262 * If no device is attached to the root port at power-up or 263 * after hot-remove, the pbus->devices is empty and this code 264 * will set the offsets to zero and the bus ops to parent's bus 265 * ops, which is unmodified. 266 */ 267 for (i = GET_INDEX(pdev->device, 0); i <= GET_INDEX(pdev->device, 7); ++i) 268 quirk_aspm_offset[i] = 0; 269 270 pci_bus_set_ops(pbus, pbus->parent->ops); 271 } else { 272 /* 273 * If devices are attached to the root port at power-up or 274 * after hot-add, the code loops through the device list of 275 * each root port to save the register offsets and replace the 276 * bus ops. 277 */ 278 list_for_each_entry(dev, &pbus->devices, bus_list) 279 /* There are 0 to 8 devices attached to this bus */ 280 quirk_aspm_offset[GET_INDEX(pdev->device, dev->devfn)] = 281 dev->pcie_cap + PCI_EXP_LNKCTL; 282 283 pci_bus_set_ops(pbus, &quirk_pcie_aspm_ops); 284 dev_info(&pbus->dev, "writes to ASPM control bits will be ignored\n"); 285 } 286 287} 288DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PA, pcie_rootport_aspm_quirk); 289DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PA1, pcie_rootport_aspm_quirk); 290DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PB, pcie_rootport_aspm_quirk); 291DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PB1, pcie_rootport_aspm_quirk); 292DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PC, pcie_rootport_aspm_quirk); 293DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_MCH_PC1, pcie_rootport_aspm_quirk); 294 295/* 296 * Fixup to mark boot BIOS video selected by BIOS before it changes 297 * 298 * From information provided by "Jon Smirl" <jonsmirl@gmail.com> 299 * 300 * The standard boot ROM sequence for an x86 machine uses the BIOS 301 * to select an initial video card for boot display. This boot video 302 * card will have its BIOS copied to 0xC0000 in system RAM. 303 * IORESOURCE_ROM_SHADOW is used to associate the boot video 304 * card with this copy. On laptops this copy has to be used since 305 * the main ROM may be compressed or combined with another image. 306 * See pci_map_rom() for use of this flag. Before marking the device 307 * with IORESOURCE_ROM_SHADOW check if a vga_default_device is already set 308 * by either arch code or vga-arbitration; if so only apply the fixup to this 309 * already-determined primary video card. 310 */ 311 312static void pci_fixup_video(struct pci_dev *pdev) 313{ 314 struct pci_dev *bridge; 315 struct pci_bus *bus; 316 u16 config; 317 struct resource *res; 318 319 /* Is VGA routed to us? */ 320 bus = pdev->bus; 321 while (bus) { 322 bridge = bus->self; 323 324 /* 325 * From information provided by 326 * "David Miller" <davem@davemloft.net> 327 * The bridge control register is valid for PCI header 328 * type BRIDGE, or CARDBUS. Host to PCI controllers use 329 * PCI header type NORMAL. 330 */ 331 if (bridge && (pci_is_bridge(bridge))) { 332 pci_read_config_word(bridge, PCI_BRIDGE_CONTROL, 333 &config); 334 if (!(config & PCI_BRIDGE_CTL_VGA)) 335 return; 336 } 337 bus = bus->parent; 338 } 339 if (!vga_default_device() || pdev == vga_default_device()) { 340 pci_read_config_word(pdev, PCI_COMMAND, &config); 341 if (config & (PCI_COMMAND_IO | PCI_COMMAND_MEMORY)) { 342 res = &pdev->resource[PCI_ROM_RESOURCE]; 343 344 pci_disable_rom(pdev); 345 if (res->parent) 346 release_resource(res); 347 348 res->start = 0xC0000; 349 res->end = res->start + 0x20000 - 1; 350 res->flags = IORESOURCE_MEM | IORESOURCE_ROM_SHADOW | 351 IORESOURCE_PCI_FIXED; 352 dev_info(&pdev->dev, "Video device with shadowed ROM at %pR\n", 353 res); 354 } 355 } 356} 357DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID, 358 PCI_CLASS_DISPLAY_VGA, 8, pci_fixup_video); 359 360 361static const struct dmi_system_id msi_k8t_dmi_table[] = { 362 { 363 .ident = "MSI-K8T-Neo2Fir", 364 .matches = { 365 DMI_MATCH(DMI_SYS_VENDOR, "MSI"), 366 DMI_MATCH(DMI_PRODUCT_NAME, "MS-6702E"), 367 }, 368 }, 369 {} 370}; 371 372/* 373 * The AMD-Athlon64 board MSI "K8T Neo2-FIR" disables the onboard sound 374 * card if a PCI-soundcard is added. 375 * 376 * The BIOS only gives options "DISABLED" and "AUTO". This code sets 377 * the corresponding register-value to enable the soundcard. 378 * 379 * The soundcard is only enabled, if the mainborad is identified 380 * via DMI-tables and the soundcard is detected to be off. 381 */ 382static void pci_fixup_msi_k8t_onboard_sound(struct pci_dev *dev) 383{ 384 unsigned char val; 385 if (!dmi_check_system(msi_k8t_dmi_table)) 386 return; /* only applies to MSI K8T Neo2-FIR */ 387 388 pci_read_config_byte(dev, 0x50, &val); 389 if (val & 0x40) { 390 pci_write_config_byte(dev, 0x50, val & (~0x40)); 391 392 /* verify the change for status output */ 393 pci_read_config_byte(dev, 0x50, &val); 394 if (val & 0x40) 395 dev_info(&dev->dev, "Detected MSI K8T Neo2-FIR; " 396 "can't enable onboard soundcard!\n"); 397 else 398 dev_info(&dev->dev, "Detected MSI K8T Neo2-FIR; " 399 "enabled onboard soundcard\n"); 400 } 401} 402DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, 403 pci_fixup_msi_k8t_onboard_sound); 404DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237, 405 pci_fixup_msi_k8t_onboard_sound); 406 407/* 408 * Some Toshiba laptops need extra code to enable their TI TSB43AB22/A. 409 * 410 * We pretend to bring them out of full D3 state, and restore the proper 411 * IRQ, PCI cache line size, and BARs, otherwise the device won't function 412 * properly. In some cases, the device will generate an interrupt on 413 * the wrong IRQ line, causing any devices sharing the line it's 414 * *supposed* to use to be disabled by the kernel's IRQ debug code. 415 */ 416static u16 toshiba_line_size; 417 418static const struct dmi_system_id toshiba_ohci1394_dmi_table[] = { 419 { 420 .ident = "Toshiba PS5 based laptop", 421 .matches = { 422 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), 423 DMI_MATCH(DMI_PRODUCT_VERSION, "PS5"), 424 }, 425 }, 426 { 427 .ident = "Toshiba PSM4 based laptop", 428 .matches = { 429 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), 430 DMI_MATCH(DMI_PRODUCT_VERSION, "PSM4"), 431 }, 432 }, 433 { 434 .ident = "Toshiba A40 based laptop", 435 .matches = { 436 DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), 437 DMI_MATCH(DMI_PRODUCT_VERSION, "PSA40U"), 438 }, 439 }, 440 { } 441}; 442 443static void pci_pre_fixup_toshiba_ohci1394(struct pci_dev *dev) 444{ 445 if (!dmi_check_system(toshiba_ohci1394_dmi_table)) 446 return; /* only applies to certain Toshibas (so far) */ 447 448 dev->current_state = PCI_D3cold; 449 pci_read_config_word(dev, PCI_CACHE_LINE_SIZE, &toshiba_line_size); 450} 451DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TI, 0x8032, 452 pci_pre_fixup_toshiba_ohci1394); 453 454static void pci_post_fixup_toshiba_ohci1394(struct pci_dev *dev) 455{ 456 if (!dmi_check_system(toshiba_ohci1394_dmi_table)) 457 return; /* only applies to certain Toshibas (so far) */ 458 459 /* Restore config space on Toshiba laptops */ 460 pci_write_config_word(dev, PCI_CACHE_LINE_SIZE, toshiba_line_size); 461 pci_read_config_byte(dev, PCI_INTERRUPT_LINE, (u8 *)&dev->irq); 462 pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, 463 pci_resource_start(dev, 0)); 464 pci_write_config_dword(dev, PCI_BASE_ADDRESS_1, 465 pci_resource_start(dev, 1)); 466} 467DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_TI, 0x8032, 468 pci_post_fixup_toshiba_ohci1394); 469 470 471/* 472 * Prevent the BIOS trapping accesses to the Cyrix CS5530A video device 473 * configuration space. 474 */ 475static void pci_early_fixup_cyrix_5530(struct pci_dev *dev) 476{ 477 u8 r; 478 /* clear 'F4 Video Configuration Trap' bit */ 479 pci_read_config_byte(dev, 0x42, &r); 480 r &= 0xfd; 481 pci_write_config_byte(dev, 0x42, r); 482} 483DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_LEGACY, 484 pci_early_fixup_cyrix_5530); 485DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_LEGACY, 486 pci_early_fixup_cyrix_5530); 487 488/* 489 * Siemens Nixdorf AG FSC Multiprocessor Interrupt Controller: 490 * prevent update of the BAR0, which doesn't look like a normal BAR. 491 */ 492static void pci_siemens_interrupt_controller(struct pci_dev *dev) 493{ 494 dev->resource[0].flags |= IORESOURCE_PCI_FIXED; 495} 496DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SIEMENS, 0x0015, 497 pci_siemens_interrupt_controller); 498 499/* 500 * SB600: Disable BAR1 on device 14.0 to avoid HPET resources from 501 * confusing the PCI engine: 502 */ 503static void sb600_disable_hpet_bar(struct pci_dev *dev) 504{ 505 u8 val; 506 507 /* 508 * The SB600 and SB700 both share the same device 509 * ID, but the PM register 0x55 does something different 510 * for the SB700, so make sure we are dealing with the 511 * SB600 before touching the bit: 512 */ 513 514 pci_read_config_byte(dev, 0x08, &val); 515 516 if (val < 0x2F) { 517 outb(0x55, 0xCD6); 518 val = inb(0xCD7); 519 520 /* Set bit 7 in PM register 0x55 */ 521 outb(0x55, 0xCD6); 522 outb(val | 0x80, 0xCD7); 523 } 524} 525DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_ATI, 0x4385, sb600_disable_hpet_bar); 526 527#ifdef CONFIG_HPET_TIMER 528static void sb600_hpet_quirk(struct pci_dev *dev) 529{ 530 struct resource *r = &dev->resource[1]; 531 532 if (r->flags & IORESOURCE_MEM && r->start == hpet_address) { 533 r->flags |= IORESOURCE_PCI_FIXED; 534 dev_info(&dev->dev, "reg 0x14 contains HPET; making it immovable\n"); 535 } 536} 537DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, 0x4385, sb600_hpet_quirk); 538#endif 539 540/* 541 * Twinhead H12Y needs us to block out a region otherwise we map devices 542 * there and any access kills the box. 543 * 544 * See: https://bugzilla.kernel.org/show_bug.cgi?id=10231 545 * 546 * Match off the LPC and svid/sdid (older kernels lose the bridge subvendor) 547 */ 548static void twinhead_reserve_killing_zone(struct pci_dev *dev) 549{ 550 if (dev->subsystem_vendor == 0x14FF && dev->subsystem_device == 0xA003) { 551 pr_info("Reserving memory on Twinhead H12Y\n"); 552 request_mem_region(0xFFB00000, 0x100000, "twinhead"); 553 } 554} 555DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x27B9, twinhead_reserve_killing_zone); 556 557/* 558 * Device [8086:2fc0] 559 * Erratum HSE43 560 * CONFIG_TDP_NOMINAL CSR Implemented at Incorrect Offset 561 * https://www.intel.com/content/www/us/en/processors/xeon/xeon-e5-v3-spec-update.html 562 * 563 * Devices [8086:6f60,6fa0,6fc0] 564 * Erratum BDF2 565 * PCI BARs in the Home Agent Will Return Non-Zero Values During Enumeration 566 * https://www.intel.com/content/www/us/en/processors/xeon/xeon-e5-v4-spec-update.html 567 */ 568static void pci_invalid_bar(struct pci_dev *dev) 569{ 570 dev->non_compliant_bars = 1; 571} 572DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x2fc0, pci_invalid_bar); 573DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x6f60, pci_invalid_bar); 574DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x6fa0, pci_invalid_bar); 575DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x6fc0, pci_invalid_bar); 576DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0xa1ec, pci_invalid_bar); 577DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0xa1ed, pci_invalid_bar); 578DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0xa26c, pci_invalid_bar); 579DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0xa26d, pci_invalid_bar); 580 581/* 582 * Device [1022:7808] 583 * 23. USB Wake on Connect/Disconnect with Low Speed Devices 584 * https://support.amd.com/TechDocs/46837.pdf 585 * Appendix A2 586 * https://support.amd.com/TechDocs/42413.pdf 587 */ 588static void pci_fixup_amd_ehci_pme(struct pci_dev *dev) 589{ 590 dev_info(&dev->dev, "PME# does not work under D3, disabling it\n"); 591 dev->pme_support &= ~((PCI_PM_CAP_PME_D3hot | PCI_PM_CAP_PME_D3cold) 592 >> PCI_PM_CAP_PME_SHIFT); 593} 594DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x7808, pci_fixup_amd_ehci_pme); 595 596/* 597 * Device [1022:7914] 598 * When in D0, PME# doesn't get asserted when plugging USB 2.0 device. 599 */ 600static void pci_fixup_amd_fch_xhci_pme(struct pci_dev *dev) 601{ 602 dev_info(&dev->dev, "PME# does not work under D0, disabling it\n"); 603 dev->pme_support &= ~(PCI_PM_CAP_PME_D0 >> PCI_PM_CAP_PME_SHIFT); 604} 605DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x7914, pci_fixup_amd_fch_xhci_pme); 606 607/* 608 * Apple MacBook Pro: Avoid [mem 0x7fa00000-0x7fbfffff] 609 * 610 * Using the [mem 0x7fa00000-0x7fbfffff] region, e.g., by assigning it to 611 * the 00:1c.0 Root Port, causes a conflict with [io 0x1804], which is used 612 * for soft poweroff and suspend-to-RAM. 613 * 614 * As far as we know, this is related to the address space, not to the Root 615 * Port itself. Attaching the quirk to the Root Port is a convenience, but 616 * it could probably also be a standalone DMI quirk. 617 * 618 * https://bugzilla.kernel.org/show_bug.cgi?id=103211 619 */ 620static void quirk_apple_mbp_poweroff(struct pci_dev *pdev) 621{ 622 struct device *dev = &pdev->dev; 623 struct resource *res; 624 625 if ((!dmi_match(DMI_PRODUCT_NAME, "MacBookPro11,4") && 626 !dmi_match(DMI_PRODUCT_NAME, "MacBookPro11,5")) || 627 pdev->bus->number != 0 || pdev->devfn != PCI_DEVFN(0x1c, 0)) 628 return; 629 630 res = request_mem_region(0x7fa00000, 0x200000, 631 "MacBook Pro poweroff workaround"); 632 if (res) 633 dev_info(dev, "claimed %s %pR\n", res->name, res); 634 else 635 dev_info(dev, "can't work around MacBook Pro poweroff issue\n"); 636} 637DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x8c10, quirk_apple_mbp_poweroff); 638 639/* 640 * VMD-enabled root ports will change the source ID for all messages 641 * to the VMD device. Rather than doing device matching with the source 642 * ID, the AER driver should traverse the child device tree, reading 643 * AER registers to find the faulting device. 644 */ 645static void quirk_no_aersid(struct pci_dev *pdev) 646{ 647 /* VMD Domain */ 648 if (is_vmd(pdev->bus) && pci_is_root_bus(pdev->bus)) 649 pdev->bus->bus_flags |= PCI_BUS_FLAGS_NO_AERSID; 650} 651DECLARE_PCI_FIXUP_CLASS_EARLY(PCI_VENDOR_ID_INTEL, PCI_ANY_ID, 652 PCI_CLASS_BRIDGE_PCI, 8, quirk_no_aersid); 653 654static void quirk_intel_th_dnv(struct pci_dev *dev) 655{ 656 struct resource *r = &dev->resource[4]; 657 658 /* 659 * Denverton reports 2k of RTIT_BAR (intel_th resource 4), which 660 * appears to be 4 MB in reality. 661 */ 662 if (r->end == r->start + 0x7ff) { 663 r->start = 0; 664 r->end = 0x3fffff; 665 r->flags |= IORESOURCE_UNSET; 666 } 667} 668DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x19e1, quirk_intel_th_dnv); 669 670#ifdef CONFIG_PHYS_ADDR_T_64BIT 671 672#define AMD_141b_MMIO_BASE(x) (0x80 + (x) * 0x8) 673#define AMD_141b_MMIO_BASE_RE_MASK BIT(0) 674#define AMD_141b_MMIO_BASE_WE_MASK BIT(1) 675#define AMD_141b_MMIO_BASE_MMIOBASE_MASK GENMASK(31,8) 676 677#define AMD_141b_MMIO_LIMIT(x) (0x84 + (x) * 0x8) 678#define AMD_141b_MMIO_LIMIT_MMIOLIMIT_MASK GENMASK(31,8) 679 680#define AMD_141b_MMIO_HIGH(x) (0x180 + (x) * 0x4) 681#define AMD_141b_MMIO_HIGH_MMIOBASE_MASK GENMASK(7,0) 682#define AMD_141b_MMIO_HIGH_MMIOLIMIT_SHIFT 16 683#define AMD_141b_MMIO_HIGH_MMIOLIMIT_MASK GENMASK(23,16) 684 685/* 686 * The PCI Firmware Spec, rev 3.2, notes that ACPI should optionally allow 687 * configuring host bridge windows using the _PRS and _SRS methods. 688 * 689 * But this is rarely implemented, so we manually enable a large 64bit BAR for 690 * PCIe device on AMD Family 15h (Models 00h-1fh, 30h-3fh, 60h-7fh) Processors 691 * here. 692 */ 693static void pci_amd_enable_64bit_bar(struct pci_dev *dev) 694{ 695 static const char *name = "PCI Bus 0000:00"; 696 struct resource *res, *conflict; 697 u32 base, limit, high; 698 struct pci_dev *other; 699 unsigned i; 700 701 if (!(pci_probe & PCI_BIG_ROOT_WINDOW)) 702 return; 703 704 /* Check that we are the only device of that type */ 705 other = pci_get_device(dev->vendor, dev->device, NULL); 706 if (other != dev || 707 (other = pci_get_device(dev->vendor, dev->device, other))) { 708 /* This is a multi-socket system, don't touch it for now */ 709 pci_dev_put(other); 710 return; 711 } 712 713 for (i = 0; i < 8; i++) { 714 pci_read_config_dword(dev, AMD_141b_MMIO_BASE(i), &base); 715 pci_read_config_dword(dev, AMD_141b_MMIO_HIGH(i), &high); 716 717 /* Is this slot free? */ 718 if (!(base & (AMD_141b_MMIO_BASE_RE_MASK | 719 AMD_141b_MMIO_BASE_WE_MASK))) 720 break; 721 722 base >>= 8; 723 base |= high << 24; 724 725 /* Abort if a slot already configures a 64bit BAR. */ 726 if (base > 0x10000) 727 return; 728 } 729 if (i == 8) 730 return; 731 732 res = kzalloc(sizeof(*res), GFP_KERNEL); 733 if (!res) 734 return; 735 736 /* 737 * Allocate a 256GB window directly below the 0xfd00000000 hardware 738 * limit (see AMD Family 15h Models 30h-3Fh BKDG, sec 2.4.6). 739 */ 740 res->name = name; 741 res->flags = IORESOURCE_PREFETCH | IORESOURCE_MEM | 742 IORESOURCE_MEM_64 | IORESOURCE_WINDOW; 743 res->start = 0xbd00000000ull; 744 res->end = 0xfd00000000ull - 1; 745 746 conflict = request_resource_conflict(&iomem_resource, res); 747 if (conflict) { 748 kfree(res); 749 if (conflict->name != name) 750 return; 751 752 /* We are resuming from suspend; just reenable the window */ 753 res = conflict; 754 } else { 755 dev_info(&dev->dev, "adding root bus resource %pR (tainting kernel)\n", 756 res); 757 add_taint(TAINT_FIRMWARE_WORKAROUND, LOCKDEP_STILL_OK); 758 pci_bus_add_resource(dev->bus, res, 0); 759 } 760 761 base = ((res->start >> 8) & AMD_141b_MMIO_BASE_MMIOBASE_MASK) | 762 AMD_141b_MMIO_BASE_RE_MASK | AMD_141b_MMIO_BASE_WE_MASK; 763 limit = ((res->end + 1) >> 8) & AMD_141b_MMIO_LIMIT_MMIOLIMIT_MASK; 764 high = ((res->start >> 40) & AMD_141b_MMIO_HIGH_MMIOBASE_MASK) | 765 ((((res->end + 1) >> 40) << AMD_141b_MMIO_HIGH_MMIOLIMIT_SHIFT) 766 & AMD_141b_MMIO_HIGH_MMIOLIMIT_MASK); 767 768 pci_write_config_dword(dev, AMD_141b_MMIO_HIGH(i), high); 769 pci_write_config_dword(dev, AMD_141b_MMIO_LIMIT(i), limit); 770 pci_write_config_dword(dev, AMD_141b_MMIO_BASE(i), base); 771} 772DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x1401, pci_amd_enable_64bit_bar); 773DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x141b, pci_amd_enable_64bit_bar); 774DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x1571, pci_amd_enable_64bit_bar); 775DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x15b1, pci_amd_enable_64bit_bar); 776DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x1601, pci_amd_enable_64bit_bar); 777DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, 0x1401, pci_amd_enable_64bit_bar); 778DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, 0x141b, pci_amd_enable_64bit_bar); 779DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, 0x1571, pci_amd_enable_64bit_bar); 780DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, 0x15b1, pci_amd_enable_64bit_bar); 781DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_AMD, 0x1601, pci_amd_enable_64bit_bar); 782 783#define RS690_LOWER_TOP_OF_DRAM2 0x30 784#define RS690_LOWER_TOP_OF_DRAM2_VALID 0x1 785#define RS690_UPPER_TOP_OF_DRAM2 0x31 786#define RS690_HTIU_NB_INDEX 0xA8 787#define RS690_HTIU_NB_INDEX_WR_ENABLE 0x100 788#define RS690_HTIU_NB_DATA 0xAC 789 790/* 791 * Some BIOS implementations support RAM above 4GB, but do not configure the 792 * PCI host to respond to bus master accesses for these addresses. These 793 * implementations set the TOP_OF_DRAM_SLOT1 register correctly, so PCI DMA 794 * works as expected for addresses below 4GB. 795 * 796 * Reference: "AMD RS690 ASIC Family Register Reference Guide" (pg. 2-57) 797 * https://www.amd.com/system/files/TechDocs/43372_rs690_rrg_3.00o.pdf 798 */ 799static void rs690_fix_64bit_dma(struct pci_dev *pdev) 800{ 801 u32 val = 0; 802 phys_addr_t top_of_dram = __pa(high_memory - 1) + 1; 803 804 if (top_of_dram <= (1ULL << 32)) 805 return; 806 807 pci_write_config_dword(pdev, RS690_HTIU_NB_INDEX, 808 RS690_LOWER_TOP_OF_DRAM2); 809 pci_read_config_dword(pdev, RS690_HTIU_NB_DATA, &val); 810 811 if (val) 812 return; 813 814 pci_info(pdev, "Adjusting top of DRAM to %pa for 64-bit DMA support\n", &top_of_dram); 815 816 pci_write_config_dword(pdev, RS690_HTIU_NB_INDEX, 817 RS690_UPPER_TOP_OF_DRAM2 | RS690_HTIU_NB_INDEX_WR_ENABLE); 818 pci_write_config_dword(pdev, RS690_HTIU_NB_DATA, top_of_dram >> 32); 819 820 pci_write_config_dword(pdev, RS690_HTIU_NB_INDEX, 821 RS690_LOWER_TOP_OF_DRAM2 | RS690_HTIU_NB_INDEX_WR_ENABLE); 822 pci_write_config_dword(pdev, RS690_HTIU_NB_DATA, 823 top_of_dram | RS690_LOWER_TOP_OF_DRAM2_VALID); 824} 825DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x7910, rs690_fix_64bit_dma); 826 827#endif 828 829#ifdef CONFIG_AMD_NB 830 831#define AMD_15B8_RCC_DEV2_EPF0_STRAP2 0x10136008 832#define AMD_15B8_RCC_DEV2_EPF0_STRAP2_NO_SOFT_RESET_DEV2_F0_MASK 0x00000080L 833 834static void quirk_clear_strap_no_soft_reset_dev2_f0(struct pci_dev *dev) 835{ 836 u32 data; 837 838 if (!amd_smn_read(0, AMD_15B8_RCC_DEV2_EPF0_STRAP2, &data)) { 839 data &= ~AMD_15B8_RCC_DEV2_EPF0_STRAP2_NO_SOFT_RESET_DEV2_F0_MASK; 840 if (amd_smn_write(0, AMD_15B8_RCC_DEV2_EPF0_STRAP2, data)) 841 pci_err(dev, "Failed to write data 0x%x\n", data); 842 } else { 843 pci_err(dev, "Failed to read data\n"); 844 } 845} 846DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, 0x15b8, quirk_clear_strap_no_soft_reset_dev2_f0); 847#endif 848