1/* SPDX-License-Identifier: GPL-2.0-or-later */
2/*
3 * arch/arm/mach-pxa/include/mach/pcm027.h
4 *
5 * (c) 2003 Phytec Messtechnik GmbH <armlinux@phytec.de>
6 * (c) 2007 Juergen Beisert <j.beisert@pengutronix.de>
7 */
8
9/*
10 * Definitions of CPU card resources only
11 */
12
13#include <mach/irqs.h> /* PXA_GPIO_TO_IRQ */
14
15/* phyCORE-PXA270 (PCM027) Interrupts */
16#define PCM027_IRQ(x)          (IRQ_BOARD_START + (x))
17#define PCM027_BTDET_IRQ       PCM027_IRQ(0)
18#define PCM027_FF_RI_IRQ       PCM027_IRQ(1)
19#define PCM027_MMCDET_IRQ      PCM027_IRQ(2)
20#define PCM027_PM_5V_IRQ       PCM027_IRQ(3)
21
22#define PCM027_NR_IRQS		(IRQ_BOARD_START + 32)
23
24/* I2C RTC */
25#define PCM027_RTC_IRQ_GPIO	0
26#define PCM027_RTC_IRQ		PXA_GPIO_TO_IRQ(PCM027_RTC_IRQ_GPIO)
27#define PCM027_RTC_IRQ_EDGE	IRQ_TYPE_EDGE_FALLING
28#define ADR_PCM027_RTC		0x51	/* I2C address */
29
30/* I2C EEPROM */
31#define ADR_PCM027_EEPROM	0x54	/* I2C address */
32
33/* Ethernet chip (SMSC91C111) */
34#define PCM027_ETH_IRQ_GPIO	52
35#define PCM027_ETH_IRQ		PXA_GPIO_TO_IRQ(PCM027_ETH_IRQ_GPIO)
36#define PCM027_ETH_IRQ_EDGE	IRQ_TYPE_EDGE_RISING
37#define PCM027_ETH_PHYS		PXA_CS5_PHYS
38#define PCM027_ETH_SIZE		(1*1024*1024)
39
40/* CAN controller SJA1000 (unsupported yet) */
41#define PCM027_CAN_IRQ_GPIO	114
42#define PCM027_CAN_IRQ		PXA_GPIO_TO_IRQ(PCM027_CAN_IRQ_GPIO)
43#define PCM027_CAN_IRQ_EDGE	IRQ_TYPE_EDGE_FALLING
44#define PCM027_CAN_PHYS		0x22000000
45#define PCM027_CAN_SIZE		0x100
46
47/* SPI GPIO expander (unsupported yet) */
48#define PCM027_EGPIO_IRQ_GPIO	27
49#define PCM027_EGPIO_IRQ	PXA_GPIO_TO_IRQ(PCM027_EGPIO_IRQ_GPIO)
50#define PCM027_EGPIO_IRQ_EDGE	IRQ_TYPE_EDGE_FALLING
51#define PCM027_EGPIO_CS		24
52/*
53 * TODO: Switch this pin from dedicated usage to GPIO if
54 * more than the MAX7301 device is connected to this SPI bus
55 */
56#define PCM027_EGPIO_CS_MODE	GPIO24_SFRM_MD
57
58/* Flash memory */
59#define PCM027_FLASH_PHYS	0x00000000
60#define PCM027_FLASH_SIZE	0x02000000
61
62/* onboard LEDs connected to GPIO */
63#define PCM027_LED_CPU		90
64#define PCM027_LED_HEARD_BEAT	91
65
66/*
67 * This CPU module needs a baseboard to work. After basic initializing
68 * its own devices, it calls baseboard's init function.
69 * TODO: Add your own basebaord init function and call it from
70 * inside pcm027_init(). This example here is for the developmen board.
71 * Refer pcm990-baseboard.c
72 */
73extern void pcm990_baseboard_init(void);
74