xref: /kernel/linux/linux-5.10/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml

# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause)
# Copyright (C) 2019 Texas Instruments Incorporated
%YAML 1.2
---
$id: http://devicetree.org/schemas/sound/tlv320adcx140.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Texas Instruments TLV320ADCX140 Quad Channel Analog-to-Digital Converter

maintainers:
  - Dan Murphy <dmurphy@ti.com>

description: |
  The TLV320ADCX140 are multichannel (4-ch analog recording or 8-ch digital
  PDM microphones recording), high-performance audio, analog-to-digital
  converter (ADC) with analog inputs supporting up to 2V RMS. The TLV320ADCX140
  family supports line and  microphone Inputs, and offers a programmable
  microphone bias or supply voltage generation.

  Specifications can be found at:
    https://www.ti.com/lit/ds/symlink/tlv320adc3140.pdf
    https://www.ti.com/lit/ds/symlink/tlv320adc5140.pdf
    https://www.ti.com/lit/ds/symlink/tlv320adc6140.pdf

properties:
  compatible:
    oneOf:
      - const: ti,tlv320adc3140
      - const: ti,tlv320adc5140
      - const: ti,tlv320adc6140

  reg:
    maxItems: 1
    description: |
      I2C addresss of the device can be one of these 0x4c, 0x4d, 0x4e or 0x4f

  reset-gpios:
    description: |
      GPIO used for hardware reset.

  areg-supply:
    description: |
      Regulator with AVDD at 3.3V.  If not defined then the internal regulator
      is enabled.

  ti,mic-bias-source:
    description: |
      Indicates the source for MIC Bias.
      0 - Mic bias is set to VREF
      1 - Mic bias is set to VREF × 1.096
      6 - Mic bias is set to AVDD
    $ref: /schemas/types.yaml#/definitions/uint32
    enum: [0, 1, 6]

  ti,vref-source:
    description: |
      Indicates the source for MIC Bias.
      0 - Set VREF to 2.75V
      1 - Set VREF to 2.5V
      2 - Set VREF to 1.375V
    $ref: /schemas/types.yaml#/definitions/uint32
    enum: [0, 1, 2]

  ti,pdm-edge-select:
    description: |
       Defines the PDMCLK sampling edge configuration for the PDM inputs.  This
       array is defined as <PDMIN1 PDMIN2 PDMIN3 PDMIN4>.

       0 - (default) Odd channel is latched on the negative edge and even
       channel is latched on the the positive edge.
       1 - Odd channel is latched on the positive edge and even channel is
       latched on the the negative edge.

       PDMIN1 - PDMCLK latching edge used for channel 1 and 2 data
       PDMIN2 - PDMCLK latching edge used for channel 3 and 4 data
       PDMIN3 - PDMCLK latching edge used for channel 5 and 6 data
       PDMIN4 - PDMCLK latching edge used for channel 7 and 8 data

    $ref: /schemas/types.yaml#/definitions/uint32-array
    minItems: 1
    maxItems: 4
    items:
      maximum: 1
    default: [0, 0, 0, 0]

  ti,gpi-config:
    description: |
       Defines the configuration for the general purpose input pins (GPI).
       The array is defined as <GPI1 GPI2 GPI3 GPI4>.

       0 - (default) disabled
       1 - GPIX is configured as a general-purpose input (GPI)
       2 - GPIX is configured as a master clock input (MCLK)
       3 - GPIX is configured as an ASI input for daisy-chain (SDIN)
       4 - GPIX is configured as a PDM data input for channel 1 and channel
            (PDMDIN1)
       5 - GPIX is configured as a PDM data input for channel 3 and channel
            (PDMDIN2)
       6 - GPIX is configured as a PDM data input for channel 5 and channel
            (PDMDIN3)
       7 - GPIX is configured as a PDM data input for channel 7 and channel
            (PDMDIN4)

    $ref: /schemas/types.yaml#/definitions/uint32-array
    minItems: 1
    maxItems: 4
    items:
      maximum: 7
    default: [0, 0, 0, 0]

  ti,asi-tx-drive:
    type: boolean
    description: |
      When set the device will set the Tx ASI output to a Hi-Z state for unused
      data cycles. Default is to drive the output low on unused ASI cycles.

patternProperties:
  '^ti,gpo-config-[1-4]$':
    $ref: /schemas/types.yaml#/definitions/uint32-array
    description: |
       Defines the configuration and output driver for the general purpose
       output pins (GPO).  These values are pairs, the first value is for the
       configuration type and the second value is for the output drive type.
       The array is defined as <GPO_CFG GPO_DRV>

       GPO output configuration can be one of the following:

       0 - (default) disabled
       1 - GPOX is configured as a general-purpose output (GPO)
       2 - GPOX is configured as a device interrupt output (IRQ)
       3 - GPOX is configured as a secondary ASI output (SDOUT2)
       4 - GPOX is configured as a PDM clock output (PDMCLK)

       GPO output drive configuration for the GPO pins can be one of the following:

       0d - (default) Hi-Z output
       1d - Drive active low and active high
       2d - Drive active low and weak high
       3d - Drive active low and Hi-Z
       4d - Drive weak low and active high
       5d - Drive Hi-Z and active high

  ti,gpio-config:
    description: |
       Defines the configuration and output drive for the General Purpose
       Input and Output pin (GPIO1). Its value is a pair, the first value is for
       the configuration type and the second value is for the output drive
       type. The array is defined as <GPIO1_CFG GPIO1_DRV>

       configuration for the GPIO pin can be one of the following:
       0 - disabled
       1 - GPIO1 is configured as a general-purpose output (GPO)
       2 - (default) GPIO1 is configured as a device interrupt output (IRQ)
       3 - GPIO1 is configured as a secondary ASI output (SDOUT2)
       4 - GPIO1 is configured as a PDM clock output (PDMCLK)
       8 - GPIO1 is configured as an input to control when MICBIAS turns on or
           off (MICBIAS_EN)
       9 - GPIO1 is configured as a general-purpose input (GPI)
       10 - GPIO1 is configured as a master clock input (MCLK)
       11 - GPIO1 is configured as an ASI input for daisy-chain (SDIN)
       12 - GPIO1 is configured as a PDM data input for channel 1 and channel 2
            (PDMDIN1)
       13 - GPIO1 is configured as a PDM data input for channel 3 and channel 4
            (PDMDIN2)
       14 - GPIO1 is configured as a PDM data input for channel 5 and channel 6
            (PDMDIN3)
       15 - GPIO1 is configured as a PDM data input for channel 7 and channel 8
            (PDMDIN4)

       output drive type for the GPIO pin can be one of the following:
       0 - Hi-Z output
       1 - Drive active low and active high
       2 - (default) Drive active low and weak high
       3 - Drive active low and Hi-Z
       4 - Drive weak low and active high
       5 - Drive Hi-Z and active high

    allOf:
      - $ref: /schemas/types.yaml#/definitions/uint32-array
      - minItems: 2
        maxItems: 2
        items:
          maximum: 15
        default: [2, 2]

required:
  - compatible
  - reg

additionalProperties: false

examples:
  - |
    #include <dt-bindings/gpio/gpio.h>
    i2c0 {
      #address-cells = <1>;
      #size-cells = <0>;
      codec: codec@4c {
        compatible = "ti,tlv320adc5140";
        reg = <0x4c>;
        ti,mic-bias-source = <6>;
        ti,pdm-edge-select = <0 1 0 1>;
        ti,gpi-config = <4 5 6 7>;
        ti,gpio-config = <10 2>;
        ti,gpo-config-1 = <0 0>;
        ti,gpo-config-2 = <0 0>;
        reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
      };
    };