xref: /kernel/linux/linux-5.10/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt

Device tree binding for NVIDIA Tegra XUSB pad controller
========================================================

The Tegra XUSB pad controller manages a set of I/O lanes (with differential
signals) which connect directly to pins/pads on the SoC package. Each lane
is controlled by a HW block referred to as a "pad" in the Tegra hardware
documentation. Each such "pad" may control either one or multiple lanes,
and thus contains any logic common to all its lanes. Each lane can be
separately configured and powered up.

Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or
super-speed USB. Other lanes are for various types of low-speed, full-speed
or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller
contains a software-configurable mux that sits between the I/O controller
ports (e.g. PCIe) and the lanes.

In addition to per-lane configuration, USB 3.0 ports may require additional
settings on a per-board basis.

Pads will be represented as children of the top-level XUSB pad controller
device tree node. Each lane exposed by the pad will be represented by its
own subnode and can be referenced by users of the lane using the standard
PHY bindings, as described by the phy-bindings.txt file in this directory.

The Tegra hardware documentation refers to the connection between the XUSB
pad controller and the XUSB controller as "ports". This is confusing since
"port" is typically used to denote the physical USB receptacle. The device
tree binding in this document uses the term "port" to refer to the logical
abstraction of the signals that are routed to a USB receptacle (i.e. a PHY
for the USB signal, the VBUS power supply, the USB 2.0 companion port for
USB 3.0 receptacles, ...).

Required properties:
--------------------
- compatible: Must be:
  - Tegra124: "nvidia,tegra124-xusb-padctl"
  - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl"
  - Tegra210: "nvidia,tegra210-xusb-padctl"
  - Tegra186: "nvidia,tegra186-xusb-padctl"
  - Tegra194: "nvidia,tegra194-xusb-padctl"
- reg: Physical base address and length of the controller's registers.
- resets: Must contain an entry for each entry in reset-names.
- reset-names: Must include the following entries:
  - "padctl"

For Tegra124:
- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V.
- avdd-pll-erefe-supply: PLLE reference PLL power supply. Must supply 1.05 V.
- avdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V.
- hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 3.3 V.

For Tegra210:
- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V.
- avdd-pll-uerefe-supply: PLLE reference PLL power supply. Must supply 1.05 V.
- dvdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V.
- hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 1.8 V.

For Tegra186:
- avdd-pll-erefeut-supply: UPHY brick and reference clock as well as UTMI PHY
  power supply. Must supply 1.8 V.
- avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
  3.3 V.
- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.
- vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V.

For Tegra194:
- avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply
  3.3 V.
- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V.

Pad nodes:
==========

A required child node named "pads" contains a list of subnodes, one for each
of the pads exposed by the XUSB pad controller. Each pad may need additional
resources that can be referenced in its pad node.

The "status" property is used to enable or disable the use of a pad. If set
to "disabled", the pad will not be used on the given board. In order to use
the pad and any of its lanes, this property must be set to "okay".

For Tegra124 and Tegra132, the following pads exist: usb2, ulpi, hsic, pcie
and sata. No extra resources are required for operation of these pads.

For Tegra210, the following pads exist: usb2, hsic, pcie and sata. Below is
a description of the properties of each pad.

UTMI pad:
---------

Required properties:
- clocks: Must contain an entry for each entry in clock-names.
- clock-names: Must contain the following entries:
  - "trk": phandle and specifier referring to the USB2 tracking clock

HSIC pad:
---------

Required properties:
- clocks: Must contain an entry for each entry in clock-names.
- clock-names: Must contain the following entries:
  - "trk": phandle and specifier referring to the HSIC tracking clock

PCIe pad:
---------

Required properties:
- clocks: Must contain an entry for each entry in clock-names.
- clock-names: Must contain the following entries:
  - "pll": phandle and specifier referring to the PLLE
- resets: Must contain an entry for each entry in reset-names.
- reset-names: Must contain the following entries:
  - "phy": reset for the PCIe UPHY block

SATA pad:
---------

Required properties:
- resets: Must contain an entry for each entry in reset-names.
- reset-names: Must contain the following entries:
  - "phy": reset for the SATA UPHY block


PHY nodes:
==========

Each pad node has a child named "lanes" that contains one or more children of
its own, each representing one of the lanes controlled by the pad.

Required properties:
--------------------
- status: Defines the operation status of the PHY. Valid values are:
  - "disabled": the PHY is disabled
  - "okay": the PHY is enabled
- #phy-cells: Should be 0. Since each lane represents a single PHY, there is
  no need for an additional specifier.
- nvidia,function: The output function of the PHY. See below for a list of
  valid functions per SoC generation.

For Tegra124 and Tegra132, the list of valid PHY nodes is given below:
- usb2: usb2-0, usb2-1, usb2-2
  - functions: "snps", "xusb", "uart"
- ulpi: ulpi-0
  - functions: "snps", "xusb"
- hsic: hsic-0, hsic-1
  - functions: "snps", "xusb"
- pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4
  - functions: "pcie", "usb3-ss"
- sata: sata-0
  - functions: "usb3-ss", "sata"

For Tegra210, the list of valid PHY nodes is given below:
- usb2: usb2-0, usb2-1, usb2-2, usb2-3
  - functions: "snps", "xusb", "uart"
- hsic: hsic-0, hsic-1
  - functions: "snps", "xusb"
- pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4, pcie-5, pcie-6
  - functions: "pcie-x1", "usb3-ss", "pcie-x4"
- sata: sata-0
  - functions: "usb3-ss", "sata"

For Tegra194, the list of valid PHY nodes is given below:
- usb2: usb2-0, usb2-1, usb2-2, usb2-3
  - functions: "xusb"
- usb3: usb3-0, usb3-1, usb3-2, usb3-3
  - functions: "xusb"

Port nodes:
===========

A required child node named "ports" contains a list of all the ports exposed
by the XUSB pad controller. Per-port configuration is only required for USB.

USB2 ports:
-----------

Required properties:
- status: Defines the operation status of the port. Valid values are:
  - "disabled": the port is disabled
  - "okay": the port is enabled
- mode: A string that determines the mode in which to run the port. Valid
  values are:
  - "host": for USB host mode
  - "device": for USB device mode
  - "otg": for USB OTG mode

Required properties for OTG/Peripheral capable USB2 ports:
- usb-role-switch: Boolean property to indicate that the port support OTG or
  peripheral mode. If present, the port supports switching between USB host
  and peripheral roles. Connector should be added as subnode.
  See usb/usb-conn-gpio.txt.

Optional properties:
- nvidia,internal: A boolean property whose presence determines that a port
  is internal. In the absence of this property the port is considered to be
  external.
- vbus-supply: phandle to a regulator supplying the VBUS voltage.

ULPI ports:
-----------

Optional properties:
- status: Defines the operation status of the port. Valid values are:
  - "disabled": the port is disabled
  - "okay": the port is enabled
- nvidia,internal: A boolean property whose presence determines that a port
  is internal. In the absence of this property the port is considered to be
  external.
- vbus-supply: phandle to a regulator supplying the VBUS voltage.

HSIC ports:
-----------

Required properties:
- status: Defines the operation status of the port. Valid values are:
  - "disabled": the port is disabled
  - "okay": the port is enabled

Optional properties:
- vbus-supply: phandle to a regulator supplying the VBUS voltage.

Super-speed USB ports:
----------------------

Required properties:
- status: Defines the operation status of the port. Valid values are:
  - "disabled": the port is disabled
  - "okay": the port is enabled
- nvidia,usb2-companion: A single cell that specifies the physical port number
  to map this super-speed USB port to. The range of valid port numbers varies
  with the SoC generation:
  - 0-2: for Tegra124 and Tegra132
  - 0-3: for Tegra210

Optional properties:
- nvidia,internal: A boolean property whose presence determines that a port
  is internal. In the absence of this property the port is considered to be
  external.

- maximum-speed: Only for Tegra194. A string property that specifies maximum
  supported speed of a usb3 port. Valid values are:
  - "super-speed-plus": default, the usb3 port supports USB 3.1 Gen 2 speed.
  - "super-speed": the usb3 port supports USB 3.1 Gen 1 speed only.

For Tegra124 and Tegra132, the XUSB pad controller exposes the following
ports:
- 3x USB2: usb2-0, usb2-1, usb2-2
- 1x ULPI: ulpi-0
- 2x HSIC: hsic-0, hsic-1
- 2x super-speed USB: usb3-0, usb3-1

For Tegra210, the XUSB pad controller exposes the following ports:
- 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3
- 2x HSIC: hsic-0, hsic-1
- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3

For Tegra194, the XUSB pad controller exposes the following ports:
- 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3
- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3

Examples:
=========

Tegra124 and Tegra132:
----------------------

SoC include:

	padctl@7009f000 {
		/* for Tegra124 */
		compatible = "nvidia,tegra124-xusb-padctl";
		/* for Tegra132 */
		compatible = "nvidia,tegra132-xusb-padctl",
			     "nvidia,tegra124-xusb-padctl";
		reg = <0x0 0x7009f000 0x0 0x1000>;
		resets = <&tegra_car 142>;
		reset-names = "padctl";

		pads {
			usb2 {
				status = "disabled";

				lanes {
					usb2-0 {
						status = "disabled";
						#phy-cells = <0>;
					};

					usb2-1 {
						status = "disabled";
						#phy-cells = <0>;
					};

					usb2-2 {
						status = "disabled";
						#phy-cells = <0>;
					};
				};
			};

			ulpi {
				status = "disabled";

				lanes {
					ulpi-0 {
						status = "disabled";
						#phy-cells = <0>;
					};
				};
			};

			hsic {
				status = "disabled";

				lanes {
					hsic-0 {
						status = "disabled";
						#phy-cells = <0>;
					};

					hsic-1 {
						status = "disabled";
						#phy-cells = <0>;
					};
				};
			};

			pcie {
				status = "disabled";

				lanes {
					pcie-0 {
						status = "disabled";
						#phy-cells = <0>;
					};

					pcie-1 {
						status = "disabled";
						#phy-cells = <0>;
					};

					pcie-2 {
						status = "disabled";
						#phy-cells = <0>;
					};

					pcie-3 {
						status = "disabled";
						#phy-cells = <0>;
					};

					pcie-4 {
						status = "disabled";
						#phy-cells = <0>;
					};
				};
			};

			sata {
				status = "disabled";

				lanes {
					sata-0 {
						status = "disabled";
						#phy-cells = <0>;
					};
				};
			};
		};

		ports {
			usb2-0 {
				status = "disabled";
			};

			usb2-1 {
				status = "disabled";
			};

			usb2-2 {
				status = "disabled";
			};

			ulpi-0 {
				status = "disabled";
			};

			hsic-0 {
				status = "disabled";
			};

			hsic-1 {
				status = "disabled";
			};

			usb3-0 {
				status = "disabled";
			};

			usb3-1 {
				status = "disabled";
			};
		};
	};

Board file:

	padctl@7009f000 {
		status = "okay";

		pads {
			usb2 {
				status = "okay";

				lanes {
					usb2-0 {
						nvidia,function = "xusb";
						status = "okay";
					};

					usb2-1 {
						nvidia,function = "xusb";
						status = "okay";
					};

					usb2-2 {
						nvidia,function = "xusb";
						status = "okay";
					};
				};
			};

			pcie {
				status = "okay";

				lanes {
					pcie-0 {
						nvidia,function = "usb3-ss";
						status = "okay";
					};

					pcie-2 {
						nvidia,function = "pcie";
						status = "okay";
					};

					pcie-4 {
						nvidia,function = "pcie";
						status = "okay";
					};
				};
			};

			sata {
				status = "okay";

				lanes {
					sata-0 {
						nvidia,function = "sata";
						status = "okay";
					};
				};
			};
		};

		ports {
			/* Micro A/B */
			usb2-0 {
				status = "okay";
				mode = "otg";
			};

			/* Mini PCIe */
			usb2-1 {
				status = "okay";
				mode = "host";
			};

			/* USB3 */
			usb2-2 {
				status = "okay";
				mode = "host";

				vbus-supply = <&vdd_usb3_vbus>;
			};

			usb3-0 {
				nvidia,port = <2>;
				status = "okay";
			};
		};
	};

Tegra210:
---------

SoC include:

	padctl@7009f000 {
		compatible = "nvidia,tegra210-xusb-padctl";
		reg = <0x0 0x7009f000 0x0 0x1000>;
		resets = <&tegra_car 142>;
		reset-names = "padctl";

		status = "disabled";

		pads {
			usb2 {
				clocks = <&tegra_car TEGRA210_CLK_USB2_TRK>;
				clock-names = "trk";
				status = "disabled";

				lanes {
					usb2-0 {
						status = "disabled";
						#phy-cells = <0>;
					};

					usb2-1 {
						status = "disabled";
						#phy-cells = <0>;
					};

					usb2-2 {
						status = "disabled";
						#phy-cells = <0>;
					};

					usb2-3 {
						status = "disabled";
						#phy-cells = <0>;
					};
				};
			};

			hsic {
				clocks = <&tegra_car TEGRA210_CLK_HSIC_TRK>;
				clock-names = "trk";
				status = "disabled";

				lanes {
					hsic-0 {
						status = "disabled";
						#phy-cells = <0>;
					};

					hsic-1 {
						status = "disabled";
						#phy-cells = <0>;
					};
				};
			};

			pcie {
				clocks = <&tegra_car TEGRA210_CLK_PLL_E>;
				clock-names = "pll";
				resets = <&tegra_car 205>;
				reset-names = "phy";
				status = "disabled";

				lanes {
					pcie-0 {
						status = "disabled";
						#phy-cells = <0>;
					};

					pcie-1 {
						status = "disabled";
						#phy-cells = <0>;
					};

					pcie-2 {
						status = "disabled";
						#phy-cells = <0>;
					};

					pcie-3 {
						status = "disabled";
						#phy-cells = <0>;
					};

					pcie-4 {
						status = "disabled";
						#phy-cells = <0>;
					};

					pcie-5 {
						status = "disabled";
						#phy-cells = <0>;
					};

					pcie-6 {
						status = "disabled";
						#phy-cells = <0>;
					};
				};
			};

			sata {
				clocks = <&tegra_car TEGRA210_CLK_PLL_E>;
				clock-names = "pll";
				resets = <&tegra_car 204>;
				reset-names = "phy";
				status = "disabled";

				lanes {
					sata-0 {
						status = "disabled";
						#phy-cells = <0>;
					};
				};
			};
		};

		ports {
			usb2-0 {
				status = "disabled";
			};

			usb2-1 {
				status = "disabled";
			};

			usb2-2 {
				status = "disabled";
			};

			usb2-3 {
				status = "disabled";
			};

			hsic-0 {
				status = "disabled";
			};

			hsic-1 {
				status = "disabled";
			};

			usb3-0 {
				status = "disabled";
			};

			usb3-1 {
				status = "disabled";
			};

			usb3-2 {
				status = "disabled";
			};

			usb3-3 {
				status = "disabled";
			};
		};
	};

Board file:

	padctl@7009f000 {
		status = "okay";

		pads {
			usb2 {
				status = "okay";

				lanes {
					usb2-0 {
						nvidia,function = "xusb";
						status = "okay";
					};

					usb2-1 {
						nvidia,function = "xusb";
						status = "okay";
					};

					usb2-2 {
						nvidia,function = "xusb";
						status = "okay";
					};

					usb2-3 {
						nvidia,function = "xusb";
						status = "okay";
					};
				};
			};

			pcie {
				status = "okay";

				lanes {
					pcie-0 {
						nvidia,function = "pcie-x1";
						status = "okay";
					};

					pcie-1 {
						nvidia,function = "pcie-x4";
						status = "okay";
					};

					pcie-2 {
						nvidia,function = "pcie-x4";
						status = "okay";
					};

					pcie-3 {
						nvidia,function = "pcie-x4";
						status = "okay";
					};

					pcie-4 {
						nvidia,function = "pcie-x4";
						status = "okay";
					};

					pcie-5 {
						nvidia,function = "usb3-ss";
						status = "okay";
					};

					pcie-6 {
						nvidia,function = "usb3-ss";
						status = "okay";
					};
				};
			};

			sata {
				status = "okay";

				lanes {
					sata-0 {
						nvidia,function = "sata";
						status = "okay";
					};
				};
			};
		};

		ports {
			usb2-0 {
				status = "okay";
				mode = "otg";
			};

			usb2-1 {
				status = "okay";
				vbus-supply = <&vdd_5v0_rtl>;
				mode = "host";
			};

			usb2-2 {
				status = "okay";
				vbus-supply = <&vdd_usb_vbus>;
				mode = "host";
			};

			usb2-3 {
				status = "okay";
				mode = "host";
			};

			usb3-0 {
				status = "okay";
				nvidia,lanes = "pcie-6";
				nvidia,port = <1>;
			};

			usb3-1 {
				status = "okay";
				nvidia,lanes = "pcie-5";
				nvidia,port = <2>;
			};
		};
	};