Home
last modified time | relevance | path

Searched refs:delay (Results 11826 - 11850 of 12462) sorted by relevance

1...<<471472473474475476477478479480>>...499

/kernel/linux/linux-6.6/drivers/net/ethernet/qlogic/qed/
H A Dqed_ll2.c18 #include <linux/delay.h>
/kernel/linux/linux-6.6/drivers/net/ethernet/realtek/
H A D8139too.c107 #include <linux/delay.h>
433 Cfg3_GNTSel = (1 << 7), /* 1 = delay 1 clock from PCI GNT signal */
1143 No extra delay is needed with 33Mhz PCI, but 66Mhz may change this.
1195 met by back-to-back PCI I/O cycles, but we insert a delay to avoid
/kernel/linux/linux-6.6/drivers/net/ethernet/sfc/falcon/
H A Dfalcon.c9 #include <linux/delay.h>
H A Dfarch.c9 #include <linux/delay.h>
H A Defx.c12 #include <linux/delay.h>
/kernel/linux/linux-6.6/drivers/net/ethernet/sfc/siena/
H A Dfarch.c9 #include <linux/delay.h>
/kernel/linux/linux-6.6/drivers/atm/
H A Dlanai.c63 #include <linux/delay.h>
517 * If we don't delay a little while here then we can end up in reset_board()
H A Deni.c17 #include <linux/delay.h>
H A Dfore200e.c25 #include <linux/delay.h>
H A Dhe.c63 #include <linux/delay.h>
/kernel/linux/linux-6.6/drivers/ata/
H A Dlibahci.c25 #include <linux/delay.h>
721 * unplugging). Otherwise a 500ms delay for each port is added. in ahci_stop_engine()
1558 * which can save timeout delay. in ahci_bad_pmp_check_ready()
H A Dsata_nv.c28 #include <linux/delay.h>
1420 /* Seems to need some delay before switching between NCQ and in nv_adma_qc_issue()
/kernel/linux/linux-6.6/fs/ocfs2/dlm/
H A Ddlmrecovery.c24 #include <linux/delay.h>
/kernel/linux/linux-6.6/drivers/scsi/
H A Dmvumi.c17 #include <linux/delay.h>
/kernel/linux/linux-6.6/drivers/staging/media/av7110/
H A Dav7110.c18 #include <linux/delay.h>
/kernel/linux/linux-6.6/drivers/staging/rtl8192e/
H A Drtllib_softmac.c17 #include <linux/delay.h>
/kernel/linux/linux-6.6/drivers/staging/rtl8192u/ieee80211/
H A Dieee80211_softmac.c17 #include <linux/delay.h>
/kernel/linux/linux-6.6/drivers/scsi/aic7xxx/
H A Daic79xx_osm.c54 #include <linux/delay.h> /* For ssleep/msleep */
64 * Set this to the delay in seconds after SCSI bus reset.
67 * delay handling for error recovery actions.
/kernel/linux/linux-6.6/drivers/tty/serial/8250/
H A D8250_port.c22 #include <linux/delay.h>
2398 * would be to delay the reading of iir. However, this is not in serial8250_do_startup()
/kernel/linux/linux-6.6/drivers/tty/serial/
H A Damba-pl011.c37 #include <linux/delay.h>
1539 * WA: introduce 26ns(1 uart clk) delay before W1C; in check_apply_cts_event_workaround()
1540 * single apb access will incur 2 pclk(133.12Mhz) delay, in check_apply_cts_event_workaround()
1777 * to get this delay write read only register 10 times in pl011_write_lcr_h()
H A Dimx.c22 #include <linux/delay.h>
445 /* continue without any delay */ in imx_uart_stop_tx()
703 /* continue without any delay */ in imx_uart_start_tx()
H A Dsamsung_tty.c40 #include <linux/delay.h>
1861 /* some delay is required after fifo reset */ in s3c24xx_serial_resetport()
/kernel/linux/linux-6.6/drivers/tty/
H A Dtty_io.c97 #include <linux/delay.h>
/kernel/linux/linux-6.6/drivers/target/
H A Dtarget_core_transport.c14 #include <linux/delay.h>
1822 * Check if we need to delay processing because of ALUA in target_submit()
/kernel/linux/linux-6.6/drivers/thunderbolt/
H A Dswitch.c9 #include <linux/delay.h>

Completed in 88 milliseconds

1...<<471472473474475476477478479480>>...499