Searched full:just (Results 17201 - 17225 of 34800) sorted by relevance
1...<<681682683684685686687688689690>>...1392
| /kernel/linux/linux-6.6/drivers/platform/x86/dell/ |
| H A D | dell-wmi-privacy.c | 93 * triggers, just a bit later than with the active ack.
|
| /kernel/linux/linux-6.6/drivers/power/reset/ |
| H A D | at91-sama5d2_shdwc.c | 121 /* Simple power-on, just bail out */ in at91_wakeup_status()
|
| /kernel/linux/linux-6.6/drivers/usb/host/ |
| H A D | bcma-hcd.c | 258 * configured. In our case the order is reversed. We just initialized in bcma_hcd_usb20_ns_init_hc()
|
| H A D | uhci-hub.c | 377 * just skip the Resume signalling. in uhci_hub_control()
|
| /kernel/linux/linux-6.6/drivers/pwm/ |
| H A D | sysfs.c | 510 * the kernel it's just not exported. in pwmchip_sysfs_export()
|
| H A D | pwm-xilinx.c | 11 * bad cycle. This could probably be fixed by reading TCR0 just before
|
| /kernel/linux/linux-6.6/drivers/power/supply/ |
| H A D | lp8727_charger.c | 520 /* If charging parameter is not defined, just skip parsing the dt */ in lp8727_parse_dt()
|
| /kernel/linux/linux-6.6/drivers/pps/ |
| H A D | pps.c | 424 * client wants to use it, just fill it in afterward.
|
| /kernel/linux/linux-6.6/drivers/regulator/ |
| H A D | scmi-regulator.c | 164 /* Just one fixed voltage exposed by SCMI */ in scmi_config_linear_regulator_mappings()
|
| /kernel/linux/linux-6.6/drivers/usb/serial/ |
| H A D | cyberjack.c | 332 /* Just to be sure */ in cyberjack_read_bulk_callback()
|
| /kernel/linux/linux-6.6/drivers/bus/ |
| H A D | omap_l3_noc.c | 194 * here. Just mask it off to prevent the error from in l3_interrupt_handler()
|
| H A D | intel-ixp4xx-eb.c | 339 /* Just this one, so set it up and return */ in ixp4xx_exp_setup_child()
|
| H A D | qcom-ebi2.c | 88 * this is something just used on the FAST chip selects. There is also a "byte
|
| H A D | qcom-ssc-block-bus.c | 279 /* low level overrides for when the HW logic doesn't "just work" */ in qcom_ssc_block_bus_probe()
|
| /kernel/linux/linux-6.6/drivers/char/ipmi/ |
| H A D | bt-bmc.c | 166 * message data follows. The read operation just tries to capture the
|
| H A D | ipmi_si_platform.c | 350 case 4: /* SSIF, just ignore */ in acpi_ipmi_probe()
|
| /kernel/linux/linux-6.6/drivers/char/hw_random/ |
| H A D | xgene-rng.c | 165 /* 1st time, just recover */ in xgene_rng_chk_overflow()
|
| /kernel/linux/linux-6.6/drivers/base/power/ |
| H A D | wakeirq.c | 120 * We assume that the wake-up interrupt just needs to wake-up the
|
| /kernel/linux/linux-6.6/drivers/clk/berlin/ |
| H A D | berlin2-avpll.c | 22 * Unfortunately, its registers are not named but just numbered. To
|
| /kernel/linux/linux-6.6/drivers/clk/ |
| H A D | clk-si544.c | 490 /* Select page 0, just to be sure, there appear to be no more */ in si544_probe()
|
| /kernel/linux/linux-6.6/drivers/block/drbd/ |
| H A D | drbd_protocol.h | 98 * which just echoes them as received.)
|
| H A D | drbd_req.h | 82 * Just like "real" requests, empty flushes (blkdev_issue_flush()) will
|
| /kernel/linux/linux-6.6/drivers/char/agp/ |
| H A D | via-agp.c | 400 * but VT3336 doesn't. - explanation from via, just leave this as
|
| /kernel/linux/linux-6.6/drivers/firmware/efi/ |
| H A D | mokvar-table.c | 292 * This routine just returns if a valid EFI MOK variable config table
|
| /kernel/linux/linux-6.6/drivers/gpio/ |
| H A D | gpio-latch.c | 36 * The above is just an example. The actual number of number of latches and
|
Completed in 33 milliseconds
1...<<681682683684685686687688689690>>...1392