| /kernel/linux/linux-5.10/drivers/net/ethernet/oki-semi/pch_gbe/ |
| H A D | pch_gbe_param.c | 154 { SPEED_100, "" },
379 case SPEED_100: in pch_gbe_check_copper_options()
387 hw->mac.link_speed = SPEED_100; in pch_gbe_check_copper_options()
390 case SPEED_100 + HALF_DUPLEX: in pch_gbe_check_copper_options()
395 hw->mac.link_speed = SPEED_100; in pch_gbe_check_copper_options()
398 case SPEED_100 + FULL_DUPLEX: in pch_gbe_check_copper_options()
403 hw->mac.link_speed = SPEED_100; in pch_gbe_check_copper_options()
|
| /kernel/linux/linux-6.6/drivers/net/ethernet/oki-semi/pch_gbe/ |
| H A D | pch_gbe_param.c | 154 { SPEED_100, "" },
379 case SPEED_100: in pch_gbe_check_copper_options()
387 hw->mac.link_speed = SPEED_100; in pch_gbe_check_copper_options()
390 case SPEED_100 + HALF_DUPLEX: in pch_gbe_check_copper_options()
395 hw->mac.link_speed = SPEED_100; in pch_gbe_check_copper_options()
398 case SPEED_100 + FULL_DUPLEX: in pch_gbe_check_copper_options()
403 hw->mac.link_speed = SPEED_100; in pch_gbe_check_copper_options()
|
| /kernel/linux/linux-5.10/drivers/net/ |
| H A D | mii.c | 112 ethtool_cmd_speed_set(ecmd, SPEED_100); in mii_ethtool_gset()
126 SPEED_100 : SPEED_10))); in mii_ethtool_gset()
198 cmd->base.speed = SPEED_100; in mii_ethtool_get_link_ksettings()
211 SPEED_100 : SPEED_10)); in mii_ethtool_get_link_ksettings()
243 speed != SPEED_100 && in mii_ethtool_sset()
307 else if (speed == SPEED_100) in mii_ethtool_sset()
336 speed != SPEED_100 && in mii_ethtool_set_link_ksettings()
404 else if (speed == SPEED_100) in mii_ethtool_set_link_ksettings()
|
| H A D | sungem_phy.c | 364 case SPEED_100: in genmii_setup_forced()
403 phy->speed = SPEED_100; in genmii_read_link()
533 case SPEED_100: in bcm54xx_setup_forced()
563 SPEED_100 : SPEED_10); in bcm54xx_read_link()
814 case SPEED_100: in marvell_setup_forced()
858 phy->speed = SPEED_100; in marvell_read_link()
|
| /kernel/linux/linux-6.6/drivers/net/ |
| H A D | mii.c | 111 ethtool_cmd_speed_set(ecmd, SPEED_100); in mii_ethtool_gset()
125 SPEED_100 : SPEED_10))); in mii_ethtool_gset()
196 cmd->base.speed = SPEED_100; in mii_ethtool_get_link_ksettings()
209 SPEED_100 : SPEED_10)); in mii_ethtool_get_link_ksettings()
241 speed != SPEED_100 && in mii_ethtool_sset()
305 else if (speed == SPEED_100) in mii_ethtool_sset()
334 speed != SPEED_100 && in mii_ethtool_set_link_ksettings()
402 else if (speed == SPEED_100) in mii_ethtool_set_link_ksettings()
|
| H A D | sungem_phy.c | 360 case SPEED_100: in genmii_setup_forced()
399 phy->speed = SPEED_100; in genmii_read_link()
529 case SPEED_100: in bcm54xx_setup_forced()
559 SPEED_100 : SPEED_10); in bcm54xx_read_link()
810 case SPEED_100: in marvell_setup_forced()
854 phy->speed = SPEED_100; in marvell_read_link()
|
| /kernel/linux/linux-5.10/drivers/net/ethernet/stmicro/stmmac/ |
| H A D | dwmac-sti.c | 183 if (spd == SPEED_100) in stih4xx_fix_retime_src()
215 else if (spd == SPEED_100) in stid127_fix_retime_src()
282 dwmac->speed = SPEED_100; in sti_dwmac_parse_data()
|
| H A D | dwmac-meson.c | 36 case SPEED_100: in meson6_dwmac_fix_mac_speed()
|
| H A D | dwmac-qcom-ethqos.c | 152 case SPEED_100: in ethqos_update_rgmii_clk()
302 case SPEED_100: in ethqos_rgmii_macro_init()
407 if (ethqos->speed != SPEED_100 && ethqos->speed != SPEED_10) { in ethqos_configure()
|
| /kernel/linux/linux-5.10/drivers/net/ethernet/chelsio/cxgb3/ |
| H A D | vsc8211.c | 159 sp = SPEED_100; in vsc8211_get_link_status()
173 sp = SPEED_100; in vsc8211_get_link_status()
235 sp = SPEED_100; in vsc8211_get_link_status_fiber()
|
| /kernel/linux/linux-6.6/drivers/net/ethernet/chelsio/cxgb3/ |
| H A D | vsc8211.c | 159 sp = SPEED_100; in vsc8211_get_link_status()
173 sp = SPEED_100; in vsc8211_get_link_status()
235 sp = SPEED_100; in vsc8211_get_link_status_fiber()
|
| /kernel/linux/linux-5.10/drivers/net/ethernet/intel/e1000/ |
| H A D | e1000_param.c | 547 { SPEED_100, "" }, in e1000_check_copper_options()
687 case SPEED_100: in e1000_check_copper_options()
694 case SPEED_100 + HALF_DUPLEX: in e1000_check_copper_options()
700 case SPEED_100 + FULL_DUPLEX: in e1000_check_copper_options()
|
| /kernel/linux/linux-6.6/drivers/net/ethernet/intel/e1000/ |
| H A D | e1000_param.c | 545 { SPEED_100, "" }, in e1000_check_copper_options()
685 case SPEED_100: in e1000_check_copper_options()
692 case SPEED_100 + HALF_DUPLEX: in e1000_check_copper_options()
698 case SPEED_100 + FULL_DUPLEX: in e1000_check_copper_options()
|
| /kernel/linux/linux-5.10/drivers/net/ethernet/ibm/ehea/ |
| H A D | ehea_ethtool.c | 39 speed = SPEED_100; in ehea_get_link_ksettings()
104 case SPEED_100: in ehea_set_link_ksettings()
|
| /kernel/linux/linux-6.6/drivers/net/ethernet/ibm/ehea/ |
| H A D | ehea_ethtool.c | 39 speed = SPEED_100; in ehea_get_link_ksettings()
104 case SPEED_100: in ehea_set_link_ksettings()
|
| /kernel/linux/linux-6.6/drivers/net/ethernet/microchip/sparx5/ |
| H A D | sparx5_port.c | 42 status->speed = SPEED_100; in decode_sgmii_word()
245 conf->speed != SPEED_100 && in sparx5_port_verify_speed()
369 spd_prm = spd == SPEED_10 ? 1000 : spd == SPEED_100 ? 100 : 10; in sparx5_port_disable()
499 case SPEED_100: in sparx5_port_fifo_sz()
607 case SPEED_100: in sparx5_port_fwd_urg()
875 clk_spd = spd == SPEED_10 ? 0 : spd == SPEED_100 ? 1 : 2; in sparx5_port_config_low_set()
878 hdx_gap_1 = spd == SPEED_1000 ? 0 : spd == SPEED_100 ? 1 : 2; in sparx5_port_config_low_set()
879 hdx_gap_2 = spd == SPEED_1000 ? 0 : spd == SPEED_100 ? 4 : 1; in sparx5_port_config_low_set()
|
| /kernel/linux/linux-5.10/drivers/net/ethernet/intel/igbvf/ |
| H A D | defines.h | 54 #define SPEED_100 100 macro
|
| /kernel/linux/linux-6.6/drivers/net/ethernet/intel/igbvf/ |
| H A D | defines.h | 54 #define SPEED_100 100 macro
|
| /kernel/linux/linux-5.10/drivers/net/ethernet/microchip/ |
| H A D | encx24j600.c | 205 if (priv->speed == SPEED_100) in encx24j600_update_phcon1()
237 ? SPEED_100 : SPEED_10; in encx24j600_wait_for_autoneg()
241 priv->speed == SPEED_100 ? "100" : "10", in encx24j600_wait_for_autoneg()
286 priv->speed = SPEED_100; in encx24j600_check_link_status()
690 if (speed == SPEED_10 || speed == SPEED_100) { in encx24j600_setlink()
693 priv->speed = (speed == SPEED_100); in encx24j600_setlink()
696 /*speeds other than SPEED_10 and SPEED_100 */ in encx24j600_setlink()
1024 priv->speed = SPEED_100; in encx24j600_spi_probe()
|
| /kernel/linux/linux-6.6/drivers/net/ethernet/microchip/ |
| H A D | encx24j600.c | 205 if (priv->speed == SPEED_100) in encx24j600_update_phcon1()
236 ? SPEED_100 : SPEED_10; in encx24j600_wait_for_autoneg()
240 priv->speed == SPEED_100 ? "100" : "10", in encx24j600_wait_for_autoneg()
285 priv->speed = SPEED_100; in encx24j600_check_link_status()
689 if (speed == SPEED_10 || speed == SPEED_100) { in encx24j600_setlink()
692 priv->speed = (speed == SPEED_100); in encx24j600_setlink()
695 /*speeds other than SPEED_10 and SPEED_100 */ in encx24j600_setlink()
1024 priv->speed = SPEED_100; in encx24j600_spi_probe()
|
| /kernel/linux/linux-5.10/drivers/net/phy/ |
| H A D | uPD60620.c | 60 phydev->speed = SPEED_100; in upd60620_read_status()
|
| /kernel/linux/linux-6.6/drivers/net/phy/ |
| H A D | ax88796b.c | 67 phydev->speed = SPEED_100; in asix_ax88772a_read_status()
|
| H A D | uPD60620.c | 60 phydev->speed = SPEED_100; in upd60620_read_status()
|
| /kernel/linux/linux-6.6/drivers/net/ethernet/stmicro/stmmac/ |
| H A D | dwmac-meson.c | 36 case SPEED_100: in meson6_dwmac_fix_mac_speed()
|
| /kernel/linux/linux-5.10/drivers/net/ethernet/ibm/emac/ |
| H A D | phy.c | 190 case SPEED_100: in genmii_setup_forced()
248 phy->speed = SPEED_100; in genmii_read_link()
270 phy->speed = SPEED_100; in genmii_read_link()
|