Lines Matching defs:set
164 * need to set this)
329 * from Beacon frame). After the first set of IEs, another set of IEs may follow
424 * The frequency is set in MHz. The array is zero-terminated.
464 * When set, the driver is expected to remove rates 1, 2, 5.5, and 11
494 * a multicast one, i.e., bit 0 of byte 0 should not be set.
504 * must be set.
565 * This optional parameter can be used to set the dwell time on each
573 * If this is set, the duration specified by the %duration field is
581 * relative_rssi_set - Whether relative RSSI parameters are set
962 * only for drivers that set WPA_DRIVER_FLAGS_4WAY_HANDSHAKE_PSK. This
973 * only for drivers that set WPA_DRIVER_FLAGS_4WAY_HANDSHAKE_PSK. This
1041 * Only bits set in the mask will be used, and not all values are used
1091 * pbss - If set, connect to a PCP in a PBSS. Otherwise, connect to an
1210 * This parameter can be used to set a specific basic rate set for the
1211 * BSS. If %NULL, default basic rate set is used.
1218 * This parameter can be used to set a specific Beacon frame data rate
1335 * not set (e.g., when 802.11g mode is not in use)
1350 * hessid - Homogeneous ESS identifier or %NULL if not set
1836 int set; /* Set STA parameters instead of add */
1969 WNM_SLEEP_TFS_REQ_IE_SET, /* AP requests driver to set TFS req IE for
1974 WNM_SLEEP_TFS_RESP_IE_SET, /* AP requests driver to set TFS resp IE
2109 * %WMM_PARAMS_UAPSD_QUEUES_INFO is set)
2286 * keys and set to zero for unicast keys); %NULL if not set
2301 * it as the default Tx key (set_tx is set) and accept Rx for all the
2407 * parameters are either a set of bssid, pmkid, and pmk; or a set of
2426 * entry for any reason. The PMKSA parameters are either a set of
2427 * bssid and pmkid; or a set of ssid, fils_cache_id, and pmkid.
2525 * with driver specific functionality. If this function pointer is set,
2544 * space applications. This function, if set, gets called with
2553 * @addr: Address of the station for which to set protection (may be
2559 * This is an optional function that can be used to set the driver to
2563 * set protection operation; instead, they set protection implicitly
2728 * template or the set of additional IEs (e.g., WPS and P2P IE).
2773 * enable/disable IEEE 802.1X support and set WPA/WPA2 parameters. This
2774 * can be left undefined (set to %NULL) if IEEE 802.1X support is
2775 * always enabled and the driver uses set_ap() to set WPA/RSN IE
2789 * kernel driver for Beacon frames. This can be left undefined (set to
2833 * undefined (set to %NULL) if the driver uses the Beacon template from
2942 * This function is used to add or set (params->set 1) a station
2950 * With TDLS, this function is used to add or set (params->set 1)
3000 * @total_flags: Bitmap of all WPA_STA_* flags currently set
3090 * network interface up) at the end of initial configuration. If set,
3138 * Beacon and Probe Response frames. This can be left undefined (set
3198 * If the %WPA_DRIVER_FLAGS_OFFCHANNEL_TX flag is set, the frame will
3202 * If the flag is not set, the wait time will be ignored. In this case,
3221 * set in the driver flags.
3335 * @encrypt: Whether to encrypt the frame (if keys are set)
3365 * This function is used to set Notice of Absence parameters for GO. It
3366 * is used only for testing. To disable NoA, all parameters are set to
3479 * @attr: Bridge port attribute to set
3480 * @val: Value to be set
3488 * @param: Bridge parameter to set
3489 * @val: Value to be set
3523 * This function can be used to set authentication algorithms for AP
3773 * @freq: If set, survey data for the specified frequency is only
3774 * being requested. If not set, all survey data is requested.
3808 * @bssid: Forced BSSID if roaming is disabled or %NULL if not set
3812 * associate() command (bssid being set there indicates that the driver
4182 * request from the IEs set by set_default_scan_ies() in the Probe
4407 * the STA and set up encryption keys with it.
4730 * This event indicates a set of frequency ranges that should be avoided
4934 * set, the results from previous scan will be used. If no
5301 * If not set to NULL, this is used for comparison with
5350 * is set.