Lines Matching refs:value
182 * @cw_min: minimum contention window [a value of the form
385 * of addresses for an interface increase beyond this value, hardware ARP
591 * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value
593 * cause an event to be sent indicating where the current value is in
595 * @cqm_rssi_low: Connection quality monitor RSSI lower threshold, a zero value
605 * TPC is enabled if value passed in %txpower_type is
608 * NL80211_TX_POWER_FIXED (use value configured from userspace)
615 * In units of 1000 TUs. Zero value indicates that the AP did not include
1052 * A value of -1 for @idx indicates an invalid rate and, if used
1364 * @RX_FLAG_NO_SIGNAL_VAL: The signal strength value is not present.
1408 * @RX_FLAG_AMPDU_EOF_BIT_KNOWN: The EOF value is known
1425 * the "0-length PSDU" field included there. The value for it is
1426 * in &struct ieee80211_rx_status. Note that if this value isn't
1471 * if the driver fills this value it should add
1504 * @mactime: value in microseconds of the 64-bit Time Synchronization Function
1535 * @he_dcm: HE DCM value
1540 * @ampdu_reference: A-MPDU reference number, must be a different value for
1683 * value only that is set to the minimum of all interfaces
1721 * @timestamp: value in microseconds of the 64-bit Time Synchronization
2268 * notifications and capabilities. The value is only valid after
2770 * @max_signal: Maximum value for signal (rssi) in RX information, used
2808 * advertise a constant value of 64 as some older APs crash if
2811 * For AddBA to HE capable peers this value will be used.
2831 * @units_pos member is set to a non-negative value then the timestamp
2836 * IEEE80211_RADIOTAP_TIMESTAMP_SPOS_* value.
3064 * value 1 to permit this specific key/algorithm to be done in software.
3151 * @dynamic_ps_timeout hardware configuration value and use it that value
3439 * Note that the vif.cab_queue value should be set to %IEEE80211_INVAL_HW_QUEUE
3540 * @action: the ampdu action, value from %ieee80211_ampdu_mlme_action.
3545 * actual ssn value used to start the session and writes the value here.
3741 * The @changed parameter indicates which value changed.
3747 * The @changed parameter indicates which value changed, and the @link_id
3753 * This callback is optional, and its return value is passed
3804 * This callback is also allowed to return the special return value 1,
3934 * @get_tsf: Get the current TSF timer value from firmware/hardware. Currently,
3939 * @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
3944 * @offset_tsf: Offset the TSF timer by the specified value in the
3972 * estimation algorithm (dynack). To disable dynack set valid value for
4174 * specified station. The returned value is expressed in Kbps. It returns 0
4354 int (*set_frag_threshold)(struct ieee80211_hw *hw, u32 value);
4355 int (*set_rts_threshold)(struct ieee80211_hw *hw, u32 value);
4659 * NULL is valid value, and means use the default naming (phy%d)
5434 * Return: new countdown value
5441 * @counter: the new value for the counter
5447 * as it will cause a race condition around the counter value.
5583 * the duration field value in little-endian byteorder.
5620 * the duration field value in little-endian byteorder.
5691 * @skb: the packet to take the IV32 value from that will be encrypted
5743 * This function writes the tkip IV value to pos (which should
5752 * @tid: The TID, or -1 for the management frame value (CCMP/GCMP only);
5753 * the value on TID 0 is also used for non-QoS frames. For
5771 * @tid: The TID, or -1 for the management frame value (CCMP/GCMP only);
5772 * the value on TID 0 is also used for non-QoS frames. For
6109 * @timeout: session timeout value (in TUs)
6514 * @rssi_level: new RSSI level value or 0 if not available
6973 * Return: The average RSSI value for the requested interface, or 0 if not