Lines Matching defs:set
43 * When set, all Link Local packets (224.0.0.X) will be treated as broadcast
82 * Master - if set, then the record describes the master system port.
88 * Note: Must be set for Spectrum.
120 * Controls the Switch aging time. Aging time is able to be set per Switch
459 * For Spectrum this value must be set to 0x1FFF
829 * Should be set to 0 when virtual ports are not enabled on the port.
885 * Priority tagged. If this bit is set, packets forwarded to the port with
886 * untagged VLAN membership (u bit is set) will be tagged with priority tag
894 * the pt bit will NOT be updated. To update the pt bit, pte must be set.
907 * Should be set to 0 when virtual ports are not enabled on the port.
990 * Should be set to 0 when virtual ports are not enabled on the port.
996 * When set, untagged frames on the ingress are allowed (default).
1002 * When set, priority tagged frames on the ingress are allowed (default).
1008 * When set, tagged frames on the ingress are allowed (default).
1388 * LAG hashing configuration. This is a bitmask, in which each set
1512 * Should be set to 0 when virtual ports are not enabled on the port.
1587 * Valid if set.
1607 * Counter set type for flow counters.
1634 * Must not be set for a non enabled RIF.
1719 * When set, the Port Prio Mode is updated with the provided ipprio_mode field.
1727 * When set, the Ingress Port VID Mode is updated with the provided ipvid_mode
1736 * When set, the Egress Port VID Mode is updated with the provided epvid_mode
1860 * router-sub-port local_port. Must not be set for a FID which is not a
1861 * router-sub-port and must be set prior to enabling the relevant RIF.
1888 * If not set, then nve_tunnel_flood_ptr is reserved and considered NULL.
1905 * If not set, then vni is reserved.
1925 * Must not be set for a non valid RIF.
2175 * is set.
2190 * Egress EtherType VLAN to push when SPVID.egr_et_set field set for the packet:
2299 bool set, bool smpe_valid, u16 smpe)
2304 mlxsw_reg_smid2_port_set(payload, port, set);
2553 * group - When set, the binding is of an ACL group. When cleared,
2555 * Must be set to 1 for Spectrum.
2561 * ACL/ACL group identifier. If the g bit is set, this field should hold
2714 * Type of action set to be used on this region.
2990 * For a new entry: set if ca=0, clear if ca=1
3007 * Action-set to perform when rule is matched.
3008 * Must be zero padded if action set is shorter.
3099 * All R/W fields are relevant for new entry. Activity bit is set
3103 /* Update action. Only action set will be updated. */
3145 * mask- in the same size as key. A bit that is set directs the TCAM
3154 * ACL action set.
3209 * 0 - The eRP is used only if bloom filter state is set for the given
3344 * All R/W fields are relevant for new entry. Activity bit is set
3400 * Delta mask must not be set for reserved fields in the key blocks.
3420 * Note: In Spectrum-2, a region of 8 key blocks must be set to either
3911 /* Forward and set color to red.
3980 * Should be set to 0 when virtual ports are not enabled on the port.
4497 * Written only when ptsc_we is set.
4631 * MTU value to set port to. Must be smaller or equal to max_mtu.
4633 * MTU is set.
4661 * Note: When set while the link is up, the changes will not take effect
4760 * Extended speed and protocol to set port to.
4766 * Speed and protocol to set port to.
4864 * reserved. HW will set incremental
4921 * 4 - Disabled by system. Can only be set by hardware.
4943 * Event update enable. If this bit is set, event generation will be
5015 * 1 - Enabled. When auto-negotiation is performed, set the Pause policy
5019 * Note: The auto-negotiation advertisement is set according to pptx and
5020 * pprtx. When PFC is set on Tx / Rx, ppan must be set to 0.
5157 * clr bit set.
5175 * for all counters in the counter group. This bit can be set
5190 * Priority for counter set that support per priority, valid values: 0-7.
5191 * Traffic class for counter set that support per traffic class,
5762 * If epsb is set, packets assigned to buffer are allowed to insert the port
5915 * If this bit is set, admin state will be updated based on admin_state field.
5923 * If this bit is set, event generation will be updated based on the e field.
5963 /* Phy local loopback. When set the port's egress traffic is looped back
6064 * Event update enable. If this bit is set, event generation will be updated
6071 * Software ignore enable bit. If this bit is set, the value of swi is used.
6079 * Software ignore. If this bit is set, the device shouldn't generate events
6207 * The register can only be set when the module is disabled by PMAOS register.
6227 * When set, will keep eeprom_override values after plug-out event.
6310 * The register can only be set when the module is disabled by PMAOS register
6541 * If set, then the device will wait for the event it sent to be acknowledged
6572 * Note: Must be set to 0 (forward) for event trap IDs, as they are already
6673 * 0 - Activity will be set when an entry is hit (default).
6674 * 1 - Activity will not be set when an entry is hit.
6811 * If the flag is set then loop-back filter for unicast packets is
6894 * LAG indication. When this bit is set the system_port field holds the
6901 * Port unique indentifier. When lag bit is set, this field holds the
7000 * same set of counters for the different type of traffic
7219 * The write may not succeed if the activity is set. There is not
7222 * response to the set command).
7343 /* IPv4, address set by mlxsw_reg_ratr_ipip_ipv4_udip. */
7345 /* IPv6, address set by mlxsw_reg_ratr_ipip_ipv6_ptr. */
7380 * Counter set type for flow counters
7495 * same set of counters for the different type of traffic
7705 * RALST is used to set and query the structure of an LPM tree.
7708 * will refer to. Therefore, bin X refers to a set of entries with prefixes
7839 * fields are written for new entry. Activity bit is set
7930 * field must be set.
8124 * relevant for new entry. Activity bit is set for new entries.
8196 * Counter set type for flow counters
8549 /* If set, allow decapsulation of IPinIP (without GRE). */
8551 /* If set, allow decapsulation of IPinGREinIP without a key. */
8553 /* If set, allow decapsulation of IPinGREinIP with a key. */
8774 * Note that low-entries must be set if high-entries are set. For
8775 * example: if erif_entry[2].v is set then erif_entry[1].v and
8776 * erif_entry[0].v must be set.
8971 * fields are relevant for new entry. Activity bit is set for new
9029 * A bit that is set directs the TCAM to compare the corresponding bit in key. A
9044 * A bit that is set directs the TCAM to compare the corresponding bit in key. A
9052 * ACL action set. The only supported action types in this field and in any
9053 * action-set pointed from here are as follows:
10065 * When set, latency-TLV is supported.
10071 * When set, string-TLV is supported.
10370 * Component properties set.
10585 /* If set, MCIA supports 128 bytes payloads. Otherwise, 48 bytes. */
10594 * When bit is set, the feature is supported in the device.
10686 * Counter set type.
11299 * Opcode Event Enable. When set a BCTOE event will be sent once the opcode
11480 * When set to '1', each change in the slot_info.provisioned / sr_valid /
11522 * If set, the data in the data field is valid and contain the information
11529 * If set, the INI file is applied and the card is provisioned.
11535 * If set, Shift Register is valid (after being provisioned) and data
11548 * If set, the LC is powered on, matching the INI version and a new FW
11555 * If set, the FW has completed the MDDC.device_enable command.
11615 * If set, the device is the flash owner. Otherwise, a shared flash
11713 * When set, FW is the manager and allowed to program the downstream device.
12029 * The hash is set by LAG hash.
12039 * The hash is set by LAG hash.
12181 * The TNQCR register configures how QoS is set in encapsulation into the
12190 * For encapsulation: How to set DSCP field:
12483 * When set, configures descriptor buffer.
12668 * When this bit is set, max_buff_occupancy field is cleared (and a
12791 * Clear Max Buffer Occupancy. When this bit is set, the max_buff_occupancy
12810 * Indicates which of the ports (for which the relevant bit is set)
12811 * are affected by the set operation. Configuration of any other port
12819 * Indicates which of the priorities (for which the relevant bit is set)
12820 * are affected by the set operation. Configuration of any other priority
12829 * Indicates which of the ports (for which the relevant bit is set)
12830 * are affected by the set operation. Configuration of any other port
12839 * set) are affected by the set operation. Configuration of any other
13106 * 4 - Disabled by system. Can only be set by hardware.