Lines Matching refs:value
1540 * Bit 0 can be used to change the Int Pin for the Function. The value is
1546 * value specified in the PCI Configuration Space.
1707 * value of the field is never reset.
1980 * Return value:
4301 * to a non-zero value to indicate when the command is completed.
4307 * Write the idle command value after the idle command parameter
4322 * Clear the tickle value. In the ASC-3550 the RISC flag
4324 * value is cleared.
4620 * The microcode will set the SCSI_CFG0 register using this value
4630 * The microcode will set the SCSI_CFG1 register using this value
4634 /* Read current SCSI_CFG1 Register value. */
4667 * termination value based on a table listed in a_condor.h.
4723 * Set filter value and possibly modified termination control
4726 * The microcode will set the SCSI_CFG1 register using this value
4735 * The microcode will set the MEM_CFG register using this value
4749 * The microcode will set the SEL_MASK register using this value
4768 * Set RISC ICQ physical address start value.
4782 * Set RISC IRQ physical address start value.
5101 * The microcode will set the SCSI_CFG0 register using this value
5111 * The microcode will set the SCSI_CFG1 register using this value
5115 /* Read current SCSI_CFG1 Register value. */
5146 * set the termination value based on a table listed in a_condor.h.
5208 * The microcode will set the SCSI_CFG1 register using this value
5216 * The microcode will set the MEM_CFG register using this value
5230 * The microcode will set the SEL_MASK register using this value
5250 * Set RISC ICQ physical address start value.
5266 * Set RISC IRQ physical address start value.
5596 * The microcode will set the SCSI_CFG0 register using this value
5606 * The microcode will set the SCSI_CFG1 register using this value
5643 * the function, then set the termination value based on a table listed
5697 * The microcode will set the SCSI_CFG1 register using this value
5705 * The microcode will set the MEM_CFG register using this value
5727 * The microcode will set the SEL_MASK register using this value
5745 * Set RISC ICQ physical address start value. Initialize the
5746 * COMMA register to the same value otherwise the RISC will
5763 * Set RISC IRQ physical address start value.
5875 /* Translate initialization return value to status value. */
6032 * the SCSI defined check condition value of
6133 * is passed the microcode ASC_MC_INTRB_CODE byte value.
6800 * the SCSI defined check condition value of
7363 * write the new value to the microcode.
7395 * 'sdtr_able' bit. Write the new value to the microcode.
7587 /* This is a byte value, otherwise it would need to be swapped. */
8443 * Clear the tickle value. In the ASC-3550 the RISC flag
8445 * value is cleared.
8716 uchar value;
8720 value = 0x00;
8722 value = dma_channel - 4;
8724 cfg_lsw |= value;
10209 /* If the value is zero, assume it is uninitialized. */
10220 /* If the value is zero, assume it is uninitialized. */
10248 * value check that a legal value is set and set the ADV_DVC_CFG
10268 * The EEPROM 'termination' field contains a bad value. Use
10385 /* If the value is zero, assume it is uninitialized. */
10396 /* If the value is zero, assume it is uninitialized. */
10424 * value check that a legal value is set and set the ADV_DVC_CFG
10443 * The EEPROM 'termination_se' field contains a bad value.
10467 * The EEPROM 'termination_lvd' field contains a bad value.
10609 /* If the value is zero, assume it is uninitialized. */
10620 /* If the value is zero, assume it is uninitialized. */
10648 * value check that a legal value is set and set the ASC_DVC_CFG
10667 * The EEPROM 'termination_se' field contains a bad value.
10691 * The EEPROM 'termination_lvd' field contains a bad value.
11001 * bus_type value. The bus_type value should no
11055 /* 'max_tag_qng' is set to the same value for every device. */
11209 * elements to be executed simultaneously. This value is
11221 * The value of 'sg_tablesize' can not exceed the SCSI