Lines Matching defs:error
181 int error;
183 error = bma150_set_reg_bits(bma150->client, mode, BMA150_WAKE_UP_POS,
185 if (error)
186 return error;
188 error = bma150_set_reg_bits(bma150->client, mode, BMA150_SLEEP_POS,
190 if (error)
191 return error;
202 int error;
204 error = bma150_set_reg_bits(bma150->client, 1, BMA150_SW_RES_POS,
206 if (error)
207 return error;
228 int error;
230 error = bma150_set_reg_bits(bma150->client, hyst,
233 if (error)
234 return error;
236 error = bma150_write_byte(bma150->client, BMA150_LOW_G_DUR_REG, dur);
237 if (error)
238 return error;
240 error = bma150_write_byte(bma150->client, BMA150_LOW_G_THRES_REG, thres);
241 if (error)
242 return error;
252 int error;
254 error = bma150_set_reg_bits(bma150->client, hyst,
257 if (error)
258 return error;
260 error = bma150_write_byte(bma150->client,
262 if (error)
263 return error;
265 error = bma150_write_byte(bma150->client,
267 if (error)
268 return error;
279 int error;
281 error = bma150_set_reg_bits(bma150->client, dur,
285 if (error)
286 return error;
288 error = bma150_write_byte(bma150->client,
290 if (error)
291 return error;
293 error = bma150_set_reg_bits(bma150->client, !!enable,
296 if (error)
297 return error;
347 int error;
349 error = pm_runtime_get_sync(&bma150->client->dev);
350 if (error < 0 && error != -ENOSYS)
351 return error;
358 error = bma150_set_mode(bma150, BMA150_MODE_NORMAL);
359 if (error)
360 return error;
379 int error;
381 error = bma150_soft_reset(bma150);
382 if (error)
383 return error;
385 error = bma150_set_bandwidth(bma150, cfg->bandwidth);
386 if (error)
387 return error;
389 error = bma150_set_range(bma150, cfg->range);
390 if (error)
391 return error;
394 error = bma150_set_any_motion_interrupt(bma150,
398 if (error)
399 return error;
401 error = bma150_set_high_g_interrupt(bma150,
404 if (error)
405 return error;
407 error = bma150_set_low_g_interrupt(bma150,
410 if (error)
411 return error;
426 int error;
429 dev_err(&client->dev, "i2c_check_functionality error\n");
435 dev_err(&client->dev, "BMA150 chip id error: %d\n", chip_id);
447 error = pdata->irq_gpio_cfg();
448 if (error) {
450 "IRQ GPIO conf. error %d, error %d\n",
451 client->irq, error);
452 return error;
460 error = bma150_initialize(bma150, cfg);
461 if (error)
462 return error;
483 error = input_setup_polling(idev, bma150_poll);
484 if (error)
485 return error;
492 error = input_register_device(idev);
493 if (error)
494 return error;
497 error = devm_request_threaded_irq(&client->dev, client->irq,
501 if (error) {
503 "irq request failed %d, error %d\n",
504 client->irq, error);
505 return error;